MA1106-EA
Operation Guide 5244
• Your watch may differ somewhat from the one shown in the illustration.
■ For a watch with an elapsed time bezel
Rotate the elapsed time bezel to align the
minute hand.
After certain amount of time elapsed, read the graduation on
the elapsed time bezel which the minute hand points to.
The elapsed time is indicated.
mark with the
Hour hand
To set the time
1. When the second hand is at
12 o’clock, pull out the crown
to the second click to stop it.
2. Set the hands by rotating the
crown. Rotate the crown to
move the hands clockwise.
Move the minute hand four or
five minutes past the time you
want to set, and then back it
up to the proper setting.
Minute hand
Elapsed time bezel
First click
• Some water resistant models are equipped with a screw
lock crown.
(Setting Day)
• With such models, you must unscrew the crown in the
direction noted in the illustration to loosen it before you can
pull it out. Do not pull too forcibly on such crowns.
• Also note that such watches are not water resistant while
their crowns are loosened. Be sure to screw the crowns
back in as far as they will go after making any setting.
ꢀꢁ
Second click
(Setting Time)
3. Push the crown back in to
the normal position to restart
timekeeping.
Crown
(Normal position)
Specifications
Day
Second hand
Accuracy at normal temperature: 20 seconds a month
Display: 3 analog hands (timekeeping hour and minutes, stopwatch seconds),
To set the day
3 dials (timekeeping seconds, stopwatch minutes and 1/20 seconds), day
1. Pull the crown out to the first click.
2. Set the day by rotating the crown.
Stopwatch function: Measuring capacity: 59'59.95"
Measuring unit: 1/20 second
Measuring mode: Elapsed time
Battery: One silver oxide battery (Type: SR927W)
Approximately 3 years on type SR927W (assuming one stopwatch operation 60 min./day)
3. Push the crown back in to the normal position.
• Avoid changing the date setting while the current time is between 9:00 p.m. and
1:00 a.m.
Using the Stopwatch
Stopwatch 1/20 second hand
* This hand rotates and
indicates the second count
during the first 30 seconds.
Stopwatch minute hand
ꢀꢁ
Stopwatch second hand
The stopwatch lets you measure elapsed time up to 59 minutes, 59.95 seconds.
To measure elapsed time (First 30 seconds)
1. Press A to start the stopwatch.
2. Press A to stop the stopwatch.
• You can resume the measurement operation by pressing A again.
3. Check the elapsed time.
• The example below shows an elapsed time of 24.65 seconds.
Stopwatch 1/20 second hand
[.65]
ꢀꢁ
Stopwatch second hand
[24 seconds]
• Press B to reset the stopwatch.
This will enter the Timekeeping Mode.
To measure elapsed time (After the first 30 seconds)
1. Press A to start the stopwatch.
• During elapsed time measurement, the stopwatch 1/20 second hand
automatically rotates for the final second of each minute.
2. Press A to stop the stopwatch.
• You can resume the measurement operation by pressing A again.
3. Press A and the stopwatch 1/20 second hand will move to the
1/20 second count.
• If the elapsed time operation was stopped during the final second of each
minute, the stopwatch 1/20 second hand will already be pointing at the
1/20 second count. Do not press A at this time, because doing so will restart
the elapsed time operation.
4. Check the elapsed time.
• The example below shows an elapsed time of two minutes, 24.65 seconds.
Stopwatch 1/20 second hand
[.65]
Stopwatch minute hand
[2 minutes]
ꢀꢁ
Stopwatch second hand
[24 seconds]
• Press B to reset the stopwatch.
This will enter the Timekeeping Mode.
Notes:
• Do not try to perform stopwatch operations while the crown is pulled out either
to the first or second click. If you try to press a button, you might accidentally
cause the crown to rotate and change the current time or day setting.
• If the starting positions of the stopwatch second hand and 1/20 second hand
become misaligned, use the following procedures to adjust the positions of the
hands so they point to 12 o’clock when the stopwatch is reset.
To adjust the positions of the stopwatch hands
1. Press B to reset the stopwatch, and check the stopwatch second hand,
1/20 second hand, and minute hand. They all should be at 12 o’clock.
2. To adjust the hands, pull out the crown to the second click.
3. Press A to move the stopwatch second hand to 12 o’clock.
• Holding down A will move the second hand at high speed, until you release
the button.
4. Press B to move the stopwatch 1/20 second hand to 12 o’clock.
• Holding down B will move the 1/20 second hand at high speed, until you
release the button.
5. After making the adjustments you want, push the crown back in to its normal
position. The stopwatch minute hand will move automatically to 12 o’clock.
• Note that pulling the crown out also stops the timekeeping second hand. After
performing the above procedure, you should also adjust the timekeeping setting.
1
|