MA0506-EA
Operation Guide DQD-70B
•
A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the clock.
ILLUSTRATION
• Depending on its model number, the configuration of your clock may differ somewhat from that shown in the illustration.
Alarm Off
Snooze Alarm On
Receive indicator
(Displayed during
signal reception.)
Snooze on indicator
Antenna icon
PM indicator
Wave OK indicator
SNZ
ON
OFF
SNZ
ON
OFF
Current time
(Hour, minutes,
seconds)
ALARM
SET
ALARM
SET
RESET
SET
DEMO
Date (month - day)
Day of the week
Alarm on indicator
Alarm time
WAVE
GENERAL GUIDE
1 SNOOZE/LIGHT button
• Press this button to illuminate the display for about five seconds.
• Pressing this button while the alarm is sounding stops the alarm.
2 Alarm Mode selector
SNZ: Snooze alarm on
ON: Alarm on
RESET
SET
DEMO
WAVE
OFF: Alarm off
3 SET button
Use this button when setting the current time.
4 DEMO button
Press this button to sound the alarm.
5 RESET button
Press this button to reset the clock after replacing its batteries.
6 WAVE button
Press this button to receive the time calibration signal and adjust timekeeping.
7 Alarm Time Set buttons
Use these buttons to change the alarm time or current time setting.
1
Operation Guide DQD-70B
2. While the screen you want is on the display, use the
Alarm Time Set buttons (7) to change the digits
that are flashing.
• Holding down + or – changes the flashing digits at
high speed.
BATTERY REPLACEMENT
Press
+
to increase
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove both of the old batteries.
3. Load two new batteries. Make sure that their positive (+) and negative (–) ends face in the correct directions. If
you load batteries incorrectly, they can burst and damage the clock.
4. Press the RESET button (5). Be sure to press the RESET button (5) after replacing batteries.
5. Replace the battery compartment cover.
the flashing digits.
Press
the flashing digits.
–
to decrease
• Your GMT differential is a value that indicates the time
difference between your current location and
Greenwich Mean Time (GMT). You can find out the
GMT differential of your location by checking the
nearby map.
• You can set the year in the range of 2000 to 2099.
The day of the week is set automatically in
accordance with the date setting.
• Pressing + or – while the Time Setting Screen is on the
display causes the seconds count to be reset to 00.
• Each press of + or – while the 12-hour/24-hour
Setting Screen is on the display toggles between
12-hour and 24-hour timekeeping.
GMT differential
:0H
:1H
:2H
:3H
Battery precautions
•
Keep batteries out of the reach of small children. If a battery is accidentally swallowed, contact your physician immediately.
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
•
Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto your skin.
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
• You can select one of 16 levels for the contrast
setting. Select the setting that makes the display easy
to read.
3. After making the settings you want, use the SET
button (3) to display the Current Time Screen.
• The clock automatically returns to the Current Time
Screen if you leave a setting screen on the display for
about three minutes without performing any operation.
USING THE ALARM
The alarm sounds when the alarm time you set is reached. You can also use the Alarm Mode selector (2) to
select the snooze alarm feature.
Setting the Alarm Time
Use the Alarm Time Set buttons (7) to set the alarm
time.
+
Press to increase
the alarm time setting.
Pressing the Alarm Time Set buttons (7) causes the
alarm time to appear in place of the date on the display.
• Holding down + or – changes the digits at high speed.
–
Press to decrease
the alarm time setting.
Turning the Alarm On and Off
Use the Alarm Mode selector (
2
) on the side of the clock to turn the alarm on and off, and to select the snooze feature.
Alarm Mode selector
Description
The alarm sounds at the preset time for one minute, and seven more times every five
minutes thereafter. Even if you stop the alarm sound by pressing the SNOOZE/LIGHT
button ( ), the alarm operation is performed again five minutes later.
SNZ
• The indicator ( ) flashes on the display to indicate that the snooze feature is
activated.
ON
The alarm sounds at the preset time for one minute.
The alarm does not sound.
OFF
• The alarm time appears in place of the date on the display whenever the Alarm Mode selector (2) is set to ON
or SNZ.
• The alarm sound changes over four levels as it sounds.
Stopping the Alarm
• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on,
the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector (2) to OFF.
USING THE LIGHT
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark.
Important!
• Overuse of the light can shorten battery life.
3
|