WASHING MACHINE
FC 1200W
INSTRUCTION BOOKLET
822 90 14-85
Important safety information
Before installing and first using the washing machine, read the instruction booklet carefully, including
its hints and warnings. Doing so will ensure that your machine will perform properly and to best
advantage. Anyone using the machine should be thoroughly familiar with its instructions for use
and safety features. Save these instructions and make sure they remain with the machine if it is
moved or sold, so that everyone using it through its life can be properly informed on appliance use
and safety.
■ Remove stains such as rust, dye, ink and grass before
Installation
■ All packaging and transit locking devices must be
machine-washing.
■ Avoid washing clothes which are frayed or excessively
removed before the machine is first used. If they are
not, the result may be damage to the machine or other
property. See the section Transit locking devices.
worn.
■ Items which have been treated with chemicals such
as stain removal products, liquid domestic cleaning
products and similar must be rinsed thoroughly by
hand before they can be washed in the machine.
■ All installation work and other work done on the product
must be carried out by a qualified technician. Work
performed by persons with inadequate knowledge
may adversely affect the satisfactory functioning of
the product and may cause personal injury or damage.
■ Wash small items such as thin socks, garment
ties/laces, lace items etc. in a special laundry net
to prevent them from getting between the inner
and outer drums.
■ The machine is heavy, so take care when lifting it.
Never lift the machine by gripping its control panel,
door, or detergent dispenser.
■ Always follow the recommendations of the manu-
facturers of detergent and fabric conditioner concerning
the quantities of these products to use. Using too
much can damage your laundry items.
■ Make sure that the power cord is not nipped or other-
wise damaged and that its hoses do not get crushed
or kinked when moving the machine in connection
with installation or cleaning etc.
■ Do not overload the drum. Overloading impairs the
machine's performance and can damage laundry
items.
■ If the power cable is damaged, it must be replaced
by a special cable or assembly available from the
manufacturer or its service agent.
■ Before opening the door always check that the water
has been pumped out of the machine.
Child Safety
■ The washing machine should be used by adults only.
Do not allow children to play with it or touch its controls
and moving/movable parts.
■ Do not leave the premises while the machine is
operating.
■ After using the machine, turn off its water supply and
disconnect it from the power supply. When removing
the electrical plug, grip the plug, not the lead.
■ When the machine is operating, the door glass will
get hot, so it should not be touched. Keep children
away from the machine when it is operating.
■ Leave the door ajar when the machine is not in use,
to prevent any stale odour.
■ Before loading the machine, check that there are
■ Make sure that the machine is disconnected from the
no foreign objects or pets inside the drum.
power supply during cleaning and maintenance work.
During Use
■ Servicing and repairs must be carried out by a service
company authorised by the supplier. Use only spare
parts supplied by these. Never try to repair the
machine yourself.
■ This machine is intended only for normal domestic
washing and only in accordance with these instructions.
Using it for other purposes could lead to physical
injury or damage to property.
■ Only machine-washable items should be washed in
the machine. If in doubt, contact the manufacturer or
retailer of the item.
Conservation
In the interest of the environment:
■ At the end of the machine's useful life, disconnect
the electrical plug from the power supply, then cut
the electrical lead at the point where it enters the
machine. Make quite sure that children will not be
able to play with the severed lead and plug.
■ Follow the recommendations of the care label, and
make sure that pockets are empty and zips and buttons
are done up before washing.
■ Objects such as coins, safety pins, nails, screws and
other hard objects can cause serious damage to the
machine. Make sure that all pockets have been emptied
before putting garments into the machine.
822 90 14-85
- 3 -
Description of the appliance
Machine front
Control panel
Door
Door latch
All feet adjustable
Machine rear
Transit locking
devices
Electrical lead
Discharge hose
Inlet hose, cold fill
- 4 -
Description of the appliance
The control panel
7
8 1 2 3 4
5
6
Push-button switches
Knob controls and detergent dispenser
5
1
2
3
– After selecting the wash programme and
temperature, push this button in to start the machine.
(See 8, Indicator light).
Temperature control – For setting temperatures
between and 90°. Follow care label recommen-
dations.
– An optional function which increases the
volume of water for rinsing in Cotton programmes,
and adds one extra rinse.
6
7
Programme control – For setting programme
type. See Programme Chart.
Detergent dispenser – With separate compartments
for detergent and fabric conditioner. Pre-wash
detergent is to be added straight into the drum,
using a dosing device.
– An optional function. When this button is
pressed in, the programme will stop at the end of
the last rinse, and the rinse water will be retained
in the machine. This function is available for the
Synthetics, Delicate, and Wool programmes, to
minimise creasing in synthetic fibres. Once the
programme has stopped on rinse-hold, if you wish
to end the wash with both emptying of water and
spinning of the load, press the option button again
so it pops out. If you wish to end the wash by
emptying the water without spinning, you have to
advance the programme control knob manually,
to programme setting L. Before you advance the
programme control knob manually, we recommend
that you first press the On/Off button to switch the
machine off (button pops out). Once the programme
control knob is set at L, press the On/Off button
again (button remains in) to complete the programme.
Indicator light – Comes on approx. 5 seconds
after the ON/OFF button is pressed, when the
door is locked electrically and the machine starts.
The light goes out approx. 2–3 minutes after the
end of the programme and the door is unlocked.
8
– An optional function which reduces the
maximum spin speed:
4
Cotton programme: 1100 ➔ 600 rpm.
Synthetics/Delicate programmes: 600 ➔ 400 rpm.
- 5 -
Using your appliance
The very first time that the machine is used you should
run a wash programme with no load in the drum, to clear
any residues which may have been left by the manufac-
turing process. Pour approx. 100 ml of detergent straight
into the drum and run programme G, 40° C.
When the programme has ended the machine will be
ready for use.
1
Loading the machine
Pull the door latch gently to open the door. Put the items
to be washed inside the drum. Large and small items can
be mixed. Try always to wash full loads: for maximum load
weights see the programme charts. You should only reduce
the load weight for heavily-soiled items and sensitive fabrics.
One way of achieving the maximum load size is to fill the
drum with dry items, but without forcing them in. Another
way is to weigh the first loads you wash, so you learn to
estimate the right load size. Close the machine door.
2
Adding detergent and fabric conditioner
The amount of detergent you use has an impact on the
performance of any washing machine. Both too much
and too little can cause problems. Use only detergent for
automatic washing machines, and follow the manufacturer's
instructions when measuring the quantity.
Increase the quantity of detergent if the load is heavily
soiled or if you have a hard water supply. Decrease the
amount for lightly soiled items or less than a full load.
Excessive foaming may indicate you have used too much
detergent.
3
The detergent dispenser is used for fabric conditioner and
detergent for the main wash. Put the detergent in the larger
compartment on the left (Fig 1) and the fabric conditioner
in the smaller one on the right (Fig. 2). Never fill the com-
partment for fabric conditioner higher than the maximum
level marked on it. If using pre-wash, add the detergent
for this straight into the drum.
Starting the machine
Before starting the programme, check:
that the door is closed
that the machine is plugged in and switched on at
the wall socket
4
that the machine's water supply is turned on
Set the temperature (Fig. 3), select the programme (Fig. 4)
and press any option buttons you require. Then press the
ON/OFF button to start the wash. The indicator light will
come on and after 5 seconds the door locks shut electrically
and the machine starts working.
- 6 -
Hints & Tips
For Best Washing Results
Always:
•
Load the laundry loosely alternating large items with
•
•
•
Empty pockets.
small ones.
Ensure buttons and zips are fastened.
•
Sort the laundry according to the type of fabric, colour
fastness and degree of soilage.
Consult the care label on the garment. Only wash
fabrics wich are designed to be machine washed.
•
•
White items should not be washed with coloured items.
•
Place small items such as socks, laces, hand-
kerchiefs etc in a washing bag or pillow case, as it
is possible for such items to slip down between the
tub and the inner drum.
Wash new coloured items separately when washing
for the first time.
•
Treat stains such as paint, ink, rust and grass before
washing.
Items that should not be put in the machine:
•
•
•
Avoid washing frayed or torn articles.
Underwired bras.
When washing fabrics requiring different wash
temperatures, always select the lowest temperature.
•
Garments which have been in contact with volatile
or petroleum based products.
•
Weigh the laundry the first few times you use the
appliance.
•
Some duvets and eiderdowns should be washed in
large commercial machines. Check with the manu-
facturer of the item.
The average weights of the most common items are
listed below as a guide:
Help the Environment:
To save water, energy and help protect the environment.
1000g = 1kg
•
•
•
•
Do not use a pre-wash for normally soiled washing.
Sheet
700-1000 g
100-200 g
400-500g
50-100 g
Wash full loads.
Pillow case
Tablecloth
Pre-treat stains and then wash at a lower temperature.
Serviette
Only use the advised quantities of detergent and
fabric softener.
Tea towel
70-120 g
Linen hand towel
Towelling hand towel
Towelling bath towel
Bath robe
100-150 g
150-250 g
700-1000 g
1000-1500 g
200-300 g
150-200 g
Man’s shirt
Apron
- 7 -
Programme chart
Cotton (dry load weight: 3.0 kg)
Load
type
Degree of
soiling
Progr.
selection
Temp.
setting
Progr. time
Programme
content
(min.) ❋
90° programme with
pre-wash. 3 rinses and
spin at 1 100 rpm.
White
articles
Heavily
soiled
~147
~135
~110
~110
~91
A
B
C
C
D
90
90
60
40
40
90° programme without
pre-wash.
White
articles
Normally
soiled
3 rinses and spin at
1 100 rpm.
60° programme without
pre-wash.
Fast
Coloureds
Normally
soiled
3 rinses and spin at
1 100 rpm.
40° programme without
pre-wash.
Non-fast
Coloureds
Normally
soiled
3 rinses and spin at
1 100 rpm.
Quick wash programme
30°-40° without pre-
wash. 3 rinses and spin
at 1 100 rpm.
Quick
wash
Lightly
soiled
Draining and spin at
1 100 rpm.
Spin
~8
~2
E
L
Drain
Draining
❋
The programme times are intended as a guide only. The actual time will vary depending on incoming water
pressure and temperature.
- 8 -
Synthetics and Delicate (dry load weight: 1.5 kg)
Wool (dry load weight: 1.0 kg)
Load
type
Degree of
soiling
Progr.
selection
Temp.
setting
Progr. time
Programme
content
(min.) ❋
60° programme without
pre-wash.
Normally
soiled
Synthetics
Synthetics
~74
~74
~56
~50
F
F
60
40
40
30
3 rinses and spin at
600 rpm.
40° programme without
pre-wash.
Lightly
soiled
3 rinses and spin at
600 rpm.
30°-40° programme
without pre-wash.
3 rinses and spin at
600 rpm.
Delicate
fabrics
Normally
soiled
G
H
-40° programme
without pre-wash.
3 rinses and spin at
600 rpm.
Woollens
Lightly
soiled
Emptying and spin at
600 rpm.
Spin
~8
~2
K
L
Drain
Draining
- Rinse-hold is an optional function available for the Synthetics, Delicate, and Wool programmes. To select
rinse-hold, press the option button on the machine control panel. Rinse-hold means that the programme halts and
the water from the last rinse is retained in the machine to minimise creasing in synthetic fibres.
Once the programme has stopped on rinse-hold, if you wish to end the wash with both emptying of water and
spinning of the load, press the option button again so it pops out.
If you wish to end the wash by emptying the water without spinning, you have to advance the programme control
knob manually, to programme setting L. Before you advance the programme control knob manually, we recommend
that you first press the On/Off button to switch the machine off (button pops out). Once the programme control knob
is set at L, press the On/Off button again (button remains in) to complete the programme.
❋
The programme times are intended as a guide only. The actual time will vary depending on incoming water
pressure and temperature.
- 9 -
Wash symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
Normal (Maximum)
FABRIC
White Cotton or Linen
without Special Finishes
Normal (Maximum)
Reduced (Medium)
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C
Nylon, Polyester/Cotton
Viscose with Special Finishes
Cotton/Acrylic Mix
Normal (Maximum)
Reduced (Medium)
Much Reduced (Minimum)
Hand wash only
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
Acrylics, Acetate, Triacetate,
Wool mixes, Polyester/wool
Wool, Wool mixtures, Silks
Do not machine wash
BLEACHING
Chlorine bleach may be used
IRONING
Hot Iron
Cotton, Linen, Viscose
Polyester mixtures, Wool
Acrylic, Nylon, Polyester
Warm Iron
Cool Iron
DRY CLEANING
P
May be dry cleaned. Other letters and/or a bar beneath the circle
will indicate the required process to the dry cleaner.
TUMBLE DRYING
May be tumble dried
With high heat setting
With low heat setting
A cross through any symbol means ‘DO NOT’
X
- 10 -
Which detergent?
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
Coloureds
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach and
therefore helps to preserve colours.
To maintain the appearance of your clothes and house-
hold textiles and to make them last longer you should use
different types of detergent for different washes, whether
for whites, colours or delicates.
Delicate Items
When washing delicates such as
woollens, you should use a product
which is specially designed to care to
care for fine fabrics. Drefs Automatic
is suitable for woollens and other
delicates.
Whites
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
Laundry Bleach
For additional stain removal you
may wish to use a product such as
Ace Gentle Bleach which is used
in addition to your chosen detergent.
Ace is suitable for all washable
fabrics including silks, woollens
and coloureds.
Non Biological
If you prefer to use a non biological
detergent, which does not contain
enzymes we recommend Fairy.
Fairy provides good cleaning and
stain removal.
And in which form?
Not only are there different types of detergent, but they
are also available in different forms. Whether you choose
a powder or liquid in traditional or compact form is down
to personal choice.
❋ If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
Fabric Conditioners
Traditional Powders
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
These are ideal for improving ‘softness’ and also reduce
static cling on synthetics and make ironing easier.
They are available in two types:
Traditional Liquids
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
the machine immediately upon placing the detergent in the
dispenser drawer. Alternatively the detergent is measured
into the specially designed dosing device❋ which should
be placed on top of the laundry and at the back of the
machine drum.
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The liquid
fabric softener should be poured into
the compartment marked with the
, start
symbol
.
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
Compact Powders and Liquids
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and generally
require a smaller dosage. Follow the manufacturer’s
instructions to ensure the most economical usage.
Pour the detergent directly into the dispenser drawer, or
alternatively measure the detergent into the specially
designed dosing device❋ which should be placed on top
of the laundry and at the back of the machine drum.
Bounce conditioning sheets for use
in a tumble dryer. We recommend the
conditioning sheets are pinned (using
a safety pin to an article of laundry and
placed in the tumble dryer).
- 11 -
Maintenance and cleaning
Use a container such as a bowl to catch water running
out of it.
The cabinet
Clean the outside surfaces of the machine using a mild
(non-abrasive) household cleaning product. Finish by
removing remaining traces of the product with a damp cloth.
Turn the programme control knob to an Drain pro-
gramme, restart the machine and let that programme
run for a short time.
The detergent dispenser
Release the discharge hose from the plastic clip
on the machine rear. Place the end of the hose in
a bowl or bucket.
In time, residues of detergent and fabric conditioner are
likely to build up inside the detergent dispenser. It should
be cleaned at regular intervals by flushing it out with water.
If necessary, the whole dispenser can be taken out of the
machine for cleaning. You need to pull it firmly outwards,
so that it comes free of a retaining stop (Fig. 1).
When you begin using the machine again, you will need
to reconnect the water intake and discharge hoses.
Do not use cleaning products which contain
alcohol (spirits), thinners and similar substances.
To remove the siphon (at the inside edge of the dispenser)
for cleaning, you need to press it inwards and pull it upwards
at the same time (Fig. 2). When you put it back, press it
downwards until you hear a distinct click.
Inside the opening for the detergent
dispenser
Detergent residues can also build up inside the opening
for the detergent dispenser. You can use an old toothbrush
for cleaning this area (Fig. 3). When you have finished and
put back the dispenser, run a short programme with no
wash load in the machine to rinse it clean.
1
2
3
Cleaning inside the machine
If you mostly use your machine for low-temperature washes
and/or if you use only very little detergent, you should clean
the inside of the machine about once a month. This will
prevent mould or stale odours from developing.
Use a normal measure of detergent, must be a powder
(such as Ariel Futur) and run a wash programme at the
highest temperature with no wash load in the machine.
Descaling
If your water supply is harder than 7° dH, you should descale
your washing machine at least once every three months.
Use approx. 150 ml of citric acid instead of detergent and
run a wash programme at the highest temperature with no
wash load in the machine. Limescale deposits on compo-
nents such as the machine's heating element will reduce
their service life. (Contact your water company to find out
the hardness level of your local water supply).
Protecting the machine against
freezing
If the machine is kept in a place where the temperature
may sometimes falls below 0° C, there is a risk that the
small amount of water which remains inside parts of the
machine after normal use will freeze and damage it.
To prevent this you should:
Turn off the water supply to the machine and dis-
connect the water intake hose from the supply pipe.
Select a wash programme, start the machine and let
the programme run for a short time.
Lower the tap end of the intake hose to floor level.
- 12 -
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling
out an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
Symptom
Check
■ Have you pressed the ON/OFF button?
■ Has the machine no power supply?
The machine will not start.
■ Check circuit-breakers/fuses (start with fuse in electrical plug).
■ Is the door closed properly?
■ Have you set the programme control knob properly?
■ Is the machine's water tap turned on?
■ Is the machine's water tap turned on?
The machine is not filling with water.
■ Has your domestic water supply been cut off temporarily?
■ Is the water intake hose kinked or blocked?
■ Is the filter inside the intake hose blocked?
■ Is the water pressure too low?
■ Is the end of the discharge hose too low down?
The machine is discharging water at
the same time as filling.
(See Installation)
■ (If discharge hose empties into wall standpipe:) is there
still a proper air gap between the end of the discharge
hose and the wall standpipe? (See Installation.)
If the machine needs to be emptied manually:
release the discharge hose from the plastic clip on the
machine rear. Lower the end of the hose to floor level,
letting it empty into a suitable container.
■ Is the programme one which pauses with rinse-hold?
(Must be advanced manually to empty or spin.)
■ Is the discharge hose kinked or blocked?
■ Has the hose been lengthened according to the instructions?
(See Installation.)
The machine will not empty or spin.
■ Have you used too much detergent?
The machine is leaking or overflowing.
The machine is vibrating or noisy.
■ Have you been using the detergent for automatic machines?
■ Are the hoses correctly installed? (See Installation.)
■ Is the detergent compartment blocked?
■ Have you removed all the transit locking devices?
■ Has the machine been installed on a suitable surface
and levelled?
■ Is the machine knocking against a wall?
■ Is the machine standing firmly on all four feet?
■ Did you wait 2-3 minutes after the end of the programme and
has the indicator light gone out?
The machine door will not open.
Read the section Loading the machine on door opening.
Never try to force the door open. Contact service.
Never attempt to repair the washing machine yourself.
Repairs carried out by unauthorised or inexperienced
persons can cause injury or serious malfunctioning.
- 13 -
Service
Service and Spare Parts
In the event of your appliance requiring service, or if you wish
to purchase spare parts, please contact your local Service
Force Centre by telephoning:
08705 929929
Your telephone call will be automatically routed to the Service
Force Centre covering your post code area.
For the address of your local Service Force Centre and further
information about Service Force, please visit the website at
For Customer Service in Ireland please contact us at
the address below:
Zanussi Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Dublin 12
Republic of Ireland
Tel: + 353 (0)1 4090751
Email: [email protected]
Before calling out an engineer, please ensure you have read
the details under the heading ”Something Not Working”.
When you contact the Service Force Centre you will need to
give the following details:
1.
2.
3.
4.
Your name, address and post code
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance
(found on the rating plate)
5.
The purchase date
Please note that a valid purchase receipt or guarantee
documentation is required for in-guarantee service calls.
Customer Care Department
For general enquiries concerning your Zanussi Electrolux
appliance or for further information on Zanussi Electrolux
products, please contact our Customer Care Department by
letter or telephone at the address below or visit our website at
Customer Care Department
Zanussi Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel:
08705 727727 *
* call to this number may be recorded for training purposes.
- 14 -
Guarantee Conditions
Standard guarantee conditions
We, Zanussi Electrolux, undertake that if within 12 months of the date of the purchase this ZANUSSI ELECTROLUX
appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at
our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
•
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate
The appliance has been used for normal domestic purposes only and in accordance with the manufacturer’s
instructions
•
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us
•
•
•
All service work under this guarantee must be undertaken by a Zanussi Electrolux Service Force Centre
Any appliance or defective part replaced shall become the Company’s property
This guarantee is in addition to your statutory and other legal rights
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours
in which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
•
•
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
United Kingdom
Appliances found to be in use within a commercial environment, plus those which are the subject to rental
agreements
Products of Zanussi Electrolux manufacture which are not marketed by Zanussi Electrolux
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject
to the following qualifications:
•
•
The guarantee starts from the date you first purchased your product
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products
•
•
•
This guarantee relates to you and cannot be transferred to another user
Your new home is within the European Community (EC) or European Free Trade Area
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household
•
The product is installed taking into account regulations in your new country
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new
home. They will then ensure that the local Service Organisation is aware of your move and able to look after you
and your appliances.
France
Germany
Italy
Senlis
+33 (0)3 44 62 29 99
+49 (0)800 234 7378
+39 (0)0434 39 4700
+46 (0)8 672 53 90
+44 (0)1753 219897
+353 (0)1 4090751
Nurnberg
Pordenone
Stockholm
Slough
Sweden
UK
Ireland
Dublin
- 15 -
Installation instructions
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Any plumbing work required to install this appliance
should be carried out by a qualified plumber or
competent person.
Technical specifications
DIMENSIONS
Height
Width
Depth
67 cm
49.5 cm
51.5 cm
WEIGHT
(net)
54 kg
RECOMMENDED CAPACITY
(DRY WEIGHT)
Cotton
3.0 kg
1.5 kg
1.0 kg
Synthetics/Delicate
Wool
WATER PRESSURES
Minimum
Maximum
50 kPa (0.5 bar)
1000 kPa (10 bar)
DRUM VOLUME
SPIN SPEED
27 litres
Maximum
1 100 rpm
ELECTRICAL DATA
Power supply
Fuse
230 V - 50 Hz
13 A
Power rating
1900 W
This appliance complies with the requirements of the following EU directives:
73/23/EEC, dated 19.02.1973 – low-voltage directive.
–
–
89/336/EEC, dated 03.05.1989 (incl. amendment
92/31/EEC) – directive on electromagnetic compatibility.
- 16 -
Unpacking the machine
If the machine is damaged
If the machine has been damaged during transportation,
you should immediately notify the company responsible
for delivering it.
1
Check that the washing machine is undamaged. If you
discover any damage, faults or that anything is missing, you
should notify the seller immediately. Never leave packaging
material in a place where children may play with it.
When lifting the machine
Take care when lifting the machine. Incorrect methods of
lifting can cause physical injuries, and also increase the
risk of damage to the machine. Open the door and take
hold of it inside the top of the door opening. You can also
grasp the rear overhang of the machine top to lift this
machine. Never lift the machine by gripping its control
panel, the door itself, or its detergent dispenser (Fig. 1).
2
Transit locking devices
When supplied the washing machine is packed using a
number of locking devices/packing pieces to prevent drum
and motor from damage in transit. These must all be
removed before the washing machine is installed.
Spread some of the polystyrene packaging materials on
the floor behind the machine and then lay the machine
carefully rear-side-down on them. Make sure that no
hoses are crushed in the process (Fig. 2).
3
Remove the polystyrene base the machine was transported
on. Then return the machine to its normal upright position
and undo the three screws on its rear (Fig. 3).
The three holes must then be plugged with the plastic
plugs supplied with the machine in the plastic bag inside
the drum (Fig. 4).
Identification of materials
All materials used in packaging this machine are
environmentally-friendly. The various plastics used
are identified and can be recycled:
• PE stands for polyethylene, which is used for the bag
around the machine and the bag in which these instructions
were supplied.
4
• PS stands for polystyrene (moulded), which is used for
the sections of packaging needed to cushion the machine.
The cardboard components of the packaging are made
from recyclable paper and should be taken to a collection
point for recycling.
The machine contains plastic and rubber components.
These have identifying marks to show what they are
made from, so they can be recycled or disposed of
properly at the end of the machine's life.
The materials are identified according to international
standards.
- 17 -
Installation
The machine must be installed on a sound and
firm surface and must not be touching walls or
furniture.
1
Levelling the machine
Adjust the feet to level the machine. Make sure
the machine is standing on all four feet. Accurate
levelling prevents vibration, noise and displacement
of the machine during operation. (Fig. 1).
Some vibration is normal and unavoidable when
the machine is spinning the load, especially if
mounted on a wooden floor.
Sprung wooden floors are particularly susceptible
to vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
2
When the appliance location is on carpet
floors, attention must be paid so as to
ensure that there is no obstruction to
the bottom vents.
Water inlet
Connect the inlet hose to a tap with a 3/4" pipe
thread (Fig. 2).
The inlet hose must not be joined onto any form
of extension hose. If it is too short, the entire hose
must be replaced with a longer high-pressure hose,
specially designed for the purpose.
3
The machine end of this hose can be turned in
any direction. Loosen the retaining nut, turn the
hose, then retighten the nut (Fig. 3).
- 18 -
Water drainage
If you intend the drain hose from the machine to
empty into a sink, make sure that the sink is empty
and that the plug hole is not blocked.
If the machine is permanently plumbed in, hook the
end of the hose into a standpipe installed for the
purpose. The standpipe must have an internal dia-
meter of at least 40 mm (1 1/2”) in order that there is
an air gap between the drain hose and the standpipe.
Make sure, that it is designed in such a way, that the
end of the drain hose cannot be covered with water.
Important
Before connecting up the machine to new pipework
or to pipework that has not been used for some time,
run off a reasonable amount of water to flush out
any debris that may have collected in the pipes.
Whether discharging into a sink or a standpipe,
check that the end of the drain hose is neither too
high not too low. The top of the curve in the hose’s
end should be no more than 800 mm (31.5”), and
no less than 450 mm (17.8”) above floor level.
The discharge hose can be extended up to total
3,5 m. For the extension piece use a hose with an
internal diameter at least as large as that of the
machine's own hose. Use a suitable hose connector.
The hose should always be routed at floor level,
rising up only where it meets the waste pipe.
Power supply
The washing machine is supplied with a lead and
electrical plug for connection to a 230 V, 13 A
earthed wall socket. Before any work is carried out
on the machine, it must be isolated from the electric
mains supply, for example by removing the plug
from the wall socket.
Permanent electrical installation must be
carried out by an authorised electrician.
- 19 -
© Electrolux plc 2003
|