X10 Wireless Technology Home Security System IN46A User Manual

Thank you for purchasing the X10 MultiView Camera  
system! This kit gives you everything you need to  
view and control up to four cameras from your PC.  
Camera Installation  
Setting Up MultiView  
1. Set the House Code on the wireless transceiver  
module (model TM751), plug it into an AC outlet and  
extend the antenna.  
First, download and install MultiView using the link  
you received by e-mail. Once this is done you are  
ready to install the USB Video Adapter (model  
VA11A). Do not connect the USB Video Adapter  
before installing MultiView.  
Getting Started  
2. Set the House Code on the ScanCam remote  
control (model CR12A) and insert 4 AAA batteries. If  
the cameras are going to be units other than 1-4,  
follow the instructions that came in the remote’s box  
to change the scan controls.  
Before you begin the installation, you will need to  
select the locations and settings for the cameras.  
These might include cameras at the front and back  
doors and in a child's room or looking at the back  
yard. The cameras will each have an X10 address,  
consisting of the House (letter) and Unit (number)  
codes. If you are already using X10 automation,  
choose a House Code that is not in use by any  
other modules or controllers. The cameras must  
be set to consecutive addresses within one of the  
following groups: 1-4, 5-8, 9-12 or 13-16.  
When the installation program instructs you to, plug  
the USB Video Adapter into a USB port on your  
computer. The computer will recognize that new  
hardware has been installed and complete the  
installation.  
3. Connect the video receiver (model VR31A) to the  
USB Video Adapter. Adjust the antenna so that it it  
faces in the general direction of all the cameras --  
sometimes it may be best to point the antenna towards  
the ceiling.  
Next, plug the Firecracker interface (model CM17A)  
into a serial port on your PC. Connect the PC  
Receiver (model MR26A) to the port on the  
Firecracker interface. Run MultiView.  
4. Set up a camera. Set the House and Unit code on  
the addressable power supply (model XM10A) as you  
chose above (see Getting Started). Plug the power  
supply into a free AC outlet. Connect the camera to  
the power supply. The camera should come on and  
you should be able to get the picture on your PC.  
Adjust the antenna so that it points better at the  
antenna of the receiver. When the camera is set up,  
turn it off using the CR12A. Repeat these steps for  
each camera you are setting up.  
5. Adjust cameras. Now that you can see the video  
from each camera, you can adjust the antenna position  
on each camera for better reception. Experiment to  
see what works best. You can also improve the picture  
by focusing the camera on the area you want to see  
best. Turn the black piece of the lens mounting to  
adjust the focus.  
6. Set up a motion sensor for each camera. Find a  
place for the Eagle Eye motion sensor (model MS14A)  
in the area where the ScanCam is installed. Follow  
the instructions in the box to set the House and Unit  
code to the same address as the camera in this  
location. Repeat these steps for each Eagle Eye.  
GUIDE:  
IN46A  
Copywrite 2001 X10 Wireless Technology, Inc. All rights reserved.  
 

Whirlpool Ventilation Hood GZ8330 User Manual
Whistler Radar Detector XTR 220 User Manual
White Westinghouse Washer SWS1233CQ S User Manual
Windsor Vacuum Cleaner 1012 0610 User Manual
Xantrex Technology Portable Generator PV225S 480 P User Manual
Yamaha Stereo Receiver HTR 5130RDS User Manual
Yamaha Stereo Receiver HTR 6080 User Manual
Zanussi Cooktop ZKC5020 User Manual
Zanussi Microwave Oven MW700 User Manual
Zanussi Refrigerator 102280 User Manual