INTRODUCTION
OWNER’S MANUAL
Note: Your warranty period begins at
the time of purchase. The warranty
is validated only by the dated store
receipt. Now is the time to record the
serial number of the unit in the space
provided in the warranty section of the
manual.
Dear Whistler Owner,
Pro 58/68
Total band protection™
LASER-RADAR
If you have questions concerning the oper-
ation of this Whistler product please
call:
DETECTOR
CuSTOmer SeRVICE
1-800-531-0004
Monday - Friday • 8:00 am - 5:00 pm CT
or visit our website
To fully acquaint yourself with the
operation of your Whistler and to
better understand the differences
between detecting radar, laser and
safety radar signals, we recommend
reading this entire manual or visit our
FAQ page on our website
www.whistlergroup.com
Please keep the receipt in a safe place.
You may register your product online
at www.whistlergroup.com. For warranty
verification purposes, a copy of your dated
store receipt must still accompany any unit
sent in for warranty work. If the unit is
returned without a dated store receipt an
out of warranty service charge applies.
The Whistler Group Corporate Headquarters
13016 N. Walton Blvd. • Bentonville, AR 72712
Tel 479.273.6012 • Fax 479.273.2927
www.whistlergroup.com
Enjoy your Whistler and please drive
Customer Return Center
551 N. 13th St. • Rogers, AR 72756
safely.
Customer Service Tel 800.531.0004
www.whistlergroup.com
Sincerely,
The Whistler Group, Inc.
P/N 203064
©
2008 The Whistler Group, Inc.
FEATURE DESCRIPTIONS
INSTALLATION
OPERATION
11. 7 Segment Icon Display – Provides intense
blue numericsignal strength indicator and band identifi-
cation.
Power On and Self-Test
Windshield Mounting
Each time your Whistler detector is turned on, an
automatic self-test sequence confirms that the
speaker and visual displays are functional.
• Press Power. Display shows in order:
1. WHISTLER 2. X-Band 3. K-Band 4. Ka-Band
5. LASER 6. HIGHWAY
• Install the two suction cups and rubber bumper
onto the bracket by fitting them into their holes.
• Press the suction cups onto the windshield at the
location you have chosen.
Important: Some newer cars have a plastic safety
coating on the inside of the windshield. The wind-
shield bracket may leave permanent marks on this
type of surface. To find out if your vehicle has this
type of windshield, check the owner’s manual or ask
your dealer. We recommend that you do not leave
the suction cup bracket on the window in direct sun-
light. If the detector is removed, this may cause
blistering of the dash in some vehicles.
• Slide the detector onto the bracket until it locks into
place.
12. Power Jack – Provides connection for the power
cord.
13. Twin Alert Periscope - Provides an addi-
tional attention getting visual alert.
14. Menu Button - (Pro-68) Enters option select
mode. (Pro-58) Engages VG-2 .
15. Dim/Dark Button - Engages Dim/Dark dis-
play options.
Setting Saver
Setting Saver saves your personalized settings so
that when the detector is turned off and then on
again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed one beep confirms fea-
ture “on”, two beeps confirm feature “off”.
INSTALLATION
Audio Level Adjustment
The audio levels can be adjusted high to low or low to high.
Pro-58:
• If necessary, the unit may be leveled by bending the
windshield bracket. Press the bracket release button
and remove the detector before bending.
Power Cord Connection
Mounting Guidelines
• Mount the unit as low as possible near the
center of the windshield.
• Press Volume up to increase audio level.
• Press Volume
Pro-68:
down to decrease audio level.
• Do not mount your unit behind wipers,
ornaments, mirrored sunscreens, etc. These
obstructions have metal surfaces which can
affect radar and laser signals and reduce
critical warning time. (Regular tinted glass
does not affect reception.)
• Plug the small end of the power cord into the
unit’s power jack.
• Move Power/Volume button back to increase audio level.
• Move Power/Volume button forward to decrease audio level.
As audio level is adjusted, beeps are provided and
the display indicates volume level.
• Plug the large end into the vehicle’s cigarette lighter.
Note: Cord fits tightly into detector. When
installing the cord, expect some resistance.
• Some windshields have an Instaclear™ or
Electriclear™ type coating, which affect radar
signals. Consult your dealer or the owner’s
manual supplied with your vehicle to determine
if your windshield has this coating.
• Avoid placing unit in direct contact with wind
shield.
Self Test Mute
Simply press the Quiet button during the self-test
sequence to cancel the self-test audio. This will not
affect radar/laser alerts. To restore the self-test
audio, simply press the Quiet button during the next
self-test.
Fuse Replacement
The lighter socket plug is equipped with a
replaceable 2 amp 3AG fuse located behind the
silver tip. To replace the fuse, carefully unscrew
the tip of the plug.
Important: Unscrew slowly. The tip contains a
spring which may fly out when disassembling.
Insert the new fuse with the spring and screw on
the tip. With use, screw cap on plug may loosen.
Retighten occasionally.
Quiet Mode
Quiet cancels audio during an alert and any new
alert within 20 seconds. After 20 seconds, approxi-
mately 2 beeps are provided on any new alert and
unit then remains quiet.
• To reduce the possibility of theft, conceal your
unit when not in use.
Windshield
Mounting
Unscrew the tip of the lighter socket plug
carefully when replacing the 2 amp fuse.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to restore
the standard audio alert pattern; or turn the unit off,
then on.
Rubber Bumper
7
5
6
OPERATION
OPERATION
OPERATION
Auto Quiet Mode
Twin Alert Periscope (Pro-68 only)
Highway Mode
Auto Quiet reduces the selected audio level to
level (1) approximately 5 seconds after a radar or
safety radar signal is detected. The alert for any
new signal within 20 seconds will resume at level
(1). Auto Quiet does not affect VG-2 or laser
Highway mode provides full audio warnings any
time radar (X, K, Ka, Safety Radar) or laser sig-
nals are detected, and is recommended for
open road driving. ( Highway Mode displays every signal )
Whistler’s new Twin Alert Periscope provides an
added attention getting visual alert. The two extra
LED’s flash on and off when the unit alarms to pro-
vide a unique visual alert. This alert can be pro-
grammed, through the Option Select Mode to: 1.
flash for all alarms, 2. remain on, or 3. turn LEDs off
completely.
For more information on City and Highway
mode, please visit our FAQ page on our web-
site: www.whistlergroup.com
alerts.
• Press Quiet/Menu (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you
may cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
City/City 1/City 2 Mode
Teach/Tutorial Mode (Pro-68 only)
Provides simulated alerts for each type of signal.
• Press City and Quiet simultaneously and
release.
Whistler’s Three Stage City Mode is designed to
reduce the annoyance of automatic door open-
ers, intrusion alarms and other devices which
share frequencies with police radar. Generally, X
band is used for these devices.
Stay Alert Feature
The Stay Alert Feature is designed to test a dri-
ver’s alertness. To engage (when unit is not
alarming) :
• Press Power to exit.
• Press City to cancel Highway mode and
engage City.
• Press City again to enter City 1 Mode
• Press City again to enter City 2 Mode
• Pressing City a fourth time cancels City 2
Mode and returns the unit to Highway Mode.
Dim/Dark Modes
• Press and hold City for approximately 2 seconds.
Release button during or immediately after the alert is
given.
Dim/Dark Modes reduce the illumination of the
display.
Pro-58:
The “H” or “C” will flash indicating Stay Alert is
activated. Within 30-60 seconds two beeps are
sounded; to show alertness, the driver must press
either the City, Volume or Quiet button within 3-5
seconds.
• Press and hold Power button for 2 seconds to
reduce illumination to a Dim setting.
• Pressing and holding the Power button for 2
seconds a second time engages Dark Mode.
The display illumination is further reduced.
• Pressing and holding the button a third time
restores full illumination to the display.
Pro-68:
In City Mode, weak speed/safety radar signals
give an initial alarm of two beeps, and then
remains quiet unless the signal becomes very
strong. When the signal strength increases, two
additional beeps are provided. City 1 and City 2
Modes operate the same as Highway Mode, but
in City 1 Mode, only the X band sensitivity is
lowered. In City 2 Mode, X-band is not detect-
ed.
If the button is pressed within 3-5 seconds, the cycle is
repeated. If a button was not pressed with in 3-5 seconds,
alarm sounds and the display will flash all LED’s.
• Press Power to exit
• Quickly press the Dark button to access
Dim/Dark settings.
WARNING!!! Stay Alert is NOT intended as a
substitute for adequate rest. You should NOT oper-
ate a vehicle if you are drowsy. During extended
periods of vehicle operation, you should take fre-
quent breaks. Improper reliance on the Stay Alert
feature may result in vehicle damage, personal
injury or death. NEVER OPERATE A VEHICLE IF
YOU ARE DROWSY.
Dim or dark can be engaged during an alert. In
Dark Mode, the display goes dark for as long as
a signal is being detected and for 20 seconds
after, then the display returns to the dimmer
setting.
Caution: Some towns/small cities may still be
using X band radar. City Modes do not change
the audio alert for laser or VG-2.
8
9
10
OPERATION
OPERATION
OPERATION
SWS
Engaging/Disengaging VG-2
Option Select Mode (Pro-68 only)
Press the Menu button to enter Option Select
Mode. Each press of the Menu button changes
to the next selectable feature.
Pro-58: Press and hold the quiet button. Unit
beeps once for VG-2 on, twice for off.
Safety Warning System™
In communities where transmitters are located,
the Safety Warning System™ displays over 60
text messages. When Safety Radar is detected
the audio alert is geiger counter-like and dis-
Pro-68: See Option Mode to engage VG-2.
The Dark (D) button and the Quiet (Q) button
turns the feature ON/OFF or Blinking. The deci-
mal point illumination indicates whether a fea-
ture is on or off. A button must be pressed with-
in 20 seconds or Option Select Mode will auto-
matically be exited.
When a VG-2 signal is detected, the VG-2 alert
is sounded. After 3 seconds the audio is can-
celled and the VG-2 indicator flashes at a slower
rate. This cycle is repeated if the VG-2 signal is
again detected. During the period a VG-2 signal
is detected, a radar signal cannot be detected.
However, because the VG-2 alert has confirmed
that a patrol car is nearby, you are already aware
of the potential for speed monitoring and can
adjust your speed accordingly. Laser detection is
not affected while a VG-2 signal is detected.
plays a
received.
to indicate a SWS™ message has been
Note: Not all areas have Safety Warning System™
transmitters.
Feature:
Option:
Filter Mode (Pro-68 only)
VG-2 (default = OFF)
D for ON, Q for OFF
There are times when a radar detector can emit
the same frequency as police radar and can
cause your detector to falsely alarm. Sometimes
a detector can display a signal when picking up
another radar detector in vehicle close by. The
Whistler Filter Mode option provide a method
to study the signal which will verify if the signal
is a legitimate police radar or a false alert from
another detector.
Twin Alert Periscope
D or Q for ON, OFF,
(default = Blinking with alert) BLINKING
X Band (default = ON)
K Band (default = ON)
Ka Band (default = ON)
D for ON, Q for OFF
D for ON, Q for OFF
D for ON, Q for OFF
Vehicle Battery Saver Mode
The Vehicle Battery Saver Mode automatically
shuts off your detector within 3 hours if you for-
get to turn it off. The timer is reset if the detec-
tor is turned off, unplugged or any button is
pressed before the 6 hours have expired. The
detector will alert you with an audible and visual
warning before it shuts off.
POP Mode (default = ON) D for ON, Q for OFF
Filter: Allows for normal filtering.
SWS (default = OFF)
Filter (default = ON)
D for ON, Q for OFF
D for ON, Q for OFF
Filter is the factory default and should provide
adequate filtering for most conditions. Filter
Mode does not override Highway or City set-
tings. See Option Select Mode to change Filter
settings.
Option Select Mode (Pro-58 only)
Press the Quiet/Menu button to enter Option
Select Mode. Each press of the Menu button
changes to the next selectable feature.
During this warning you can reset the timer by
pressing any button.
Feature:
Option:
If the unit has automatically turned itself off,
press the Power button to turn the unit back on.
You can manually engage the Vehicle Battery
Saver Mode by pressing and holding the City
button until one beep is heard.
VG-2 (default = OFF)
Press and hold Q uiet
“V” Indicates its on
POP Mode (default = ON) Press and hold both Volume
Buttons “P” indiactes POP ON
11
12
13
POP MODE ALERTS
VG-2 ALERTS
RESET FEATURES
POP™ Mode Alerts
VG-2 Audio/Visual Alerts
Note: You must turn this feature on before it will
detect VG-2.
Reset Features
Because POP™ Mode travels on regular radar
bandwidth, there is no particular alert for POP™
Mode transmissions. POP™ Mode alerts will be
displayed as a regular radar alert.
All user features can be reset to factory settings.
• Unplug Power Cord from unit.
• Press and hold Power and Quiet.
• Plug Power Cord into unit.
• Wait for 2 beeps.
• Release Power and Quiet buttons.
When a VG-2 signal is detected, the detector ‘hides’ its
own radiated signal and becomes undetectable by
the VG-2.
Every 30 seconds, the detector checks for a VG-2
signal. If a VG-2 signal is still present, the unit
continues to hide and repeats the VG-2 alert. If no
signal is detected, two beeps are provided,
indicating an ‘all clear’ condition. During a VG-2
Alert X, K, and Ka band signals cannot be
received (Reference page 21 for VG-2 information).
LASER/RADAR ALERTS
Speed Radar Audio/Visual Alerts
When X, K or Ka is detected, the band ID and
signal strength is displayed. The audio alert is
continuous and has a geiger counter-like
pattern. The faster the beep, the closer or
stronger the radar source.
Unit is now reset to the following features
and settings.
Default factory settings are:
1. Audio to level (4).
2. Display shows “H”
3. Auto Quiet Mode OFF.
4. VG-2 Detection Mode OFF.
5. Safety Radar OFF. (Pro-68 only)
6. Dim/Dark Mode to full illumination.
7. All Radar Bands ON. (Pro-68 only)
8. LED Periscope to Blink. (Pro-68 only)
9. POP ON.
Laser Audio/Visual Alerts
Alert Priority
When a laser signal is detected the audio alert is
continuous for a minimum of 3 seconds.
When two or more signals are received at the
same time, the alert priority is:
1. Laser
• The unit shows an “L”.
2. VG-2
®
Pulse Protection
3. Speed Radar
Pulse (or instant-on) radar is more difficult to
detect than conventional radar because it
remains ‘off’ until activated to measure the speed
of a targeted vehicle.
10. Display at full illumination
4. Safety Radar
Example:
TROUBLESHOOTING
If X band is alerting, then suddenly a VG-2
signal is detected, the VG-2 warning will
override the X band alert.
Your Whistler detector is expertly engineered
and designed to exacting quality standards to
provide you with reliable, trouble-free operation.
If your unit has been correctly installed following
the guidelines in this manual, but is not
operating optimally, please refer to the
troubleshooting guide below.
When a pulse type transmission is detected, your
Whistler detector sounds an urgent 3-second
audio warning and the unit displays a “P”.
After the 3-second pulse alert, the standard alert
pattern continues for as long as the signal is
present.
It is important to respond promptly to a pulse
alert, since warning time may be minimal.
PROBLEM: No display or audio.
• Check fuse in Whistler plug; replace if
necessary with a 2 amp 3AG type.
• Check fuse for lighter socket; replace if
necessary.
• Make sure lighter socket is clean.
14
15
16
TROUBLESHOOTING
CARE AND MAINTENANCE
FCC INFORMATION
PROBLEM: Unit alarms when vehicle hits
bumps.
FCC ID : HSXWH11 - Pro-58, Pro-68
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
Care And Maintenance
During the summer months, avoid prolonged
exposure to direct sunlight by removing your unit
from the dash when your vehicle is parked for an
extended period of time. Do not spray water,
cleaners, or polishes directly onto the unit. The
spray may penetrate through the openings and
damage the unit. Also, do not use any abrasive
cleaners on the unit’s exterior.
• Check for loose lighter socket; tighten and
clean.
• Check connections at both ends of power
cord. Substitute another cord to determine if
cord is defective. Return defective cord to
the factory.
(1) This device many not cause harmful
interference, and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.
Important: FCC requirements state that
changes or modifications not expressly approved
by Whistler could void the user’s authority to
operate the equipment.
PROBLEM: Audio alerts are not loud
enough.
• Cancel Auto Quiet Mode or City Mode.
• Check audio level setting (see page 7 ).
ARE DETECTORS LEGAL?
In Most States YES!
Laser-Radar detectors are legal in every state
(with the exception of Virginia and Washington,
D.C., which have local regulations restricting the
use of radar receivers in any vehicle) when used
in automobiles or light trucks (under 10,000 lbs.).
If difficulties occur which cannot be solved by
information in this Troubleshooting Guide, please
call Whistler Customer Service at 1-800-531-0004
or visit our FAQ page at
www.whistlergroup.com/faq-detectors.asp,
before returning your unit for service.
SPEED MONITORING
Radar Facts
A radar gun operates by transmitting radio
waves at certain frequencies which reflect off
objects and are picked up by the radar gun’s
receiving section. When a radar beam reflects
off a moving target, a measurable frequency shift
occurs. The radar unit converts this shift into miles
per hour to determine your vehicle’s speed.
Currently, the FCC (Federal Communications
Commission) permits operation of traffic radar
guns at X Band (10.500 - 10.550 GHz), K Band
(24.050 - 24.250 GHz), and Ka Band (33.400 -
36.000 GHz).
Concerning trucks over 10,000 lbs., the Federal
Highway Administration (FHWA) issued a
regulation, effective January, 1994 which prohibits
radar and laser detector use in these types of
vehicles nationally. Prior to the FHWA regulation,
laws existed in the state of New York restricting
the use of radar detectors in trucks over 18,000
lbs. and in Illinois in trucks over 26,000 lbs.
Note: A radar detector will not alarm if an offi-
cer is not transmitting on any one of the above
radar bands.
POP™ Mode
POP™ Mode is a feature on some newer radar
guns operating on K and Ka bands. When the
gun is in POP™ Mode and activated, a brief burst
of energy, less that 1/15 of a second, is transmit-
ted and the vehicle’s speed is quickly acquired. A
detector without POP™ Mode detection capabili-
ty cannot respond to this brief transmission.
19
17
18
SPEED MONITORING
SPEED MONITORING
SPEED MONITORING
Note: Having a radar detector capable of
detecting the VG-2 may alert you to the pres-
ence of a speed trap. The newest tool Police
have to detect radar detectors is called Spectre.
As of thhis printing. Spectre can detect the
majority of undetectable (VG-2) laser/radar
detectors on the market.
Laser Tips
Total Band Protection™
If you are the targeted vehicle, a laser gun can
often determine your speed within a few
seconds after you receive an alert. In this situa-
tion there is generally no time to safely adjust
your speed. However, if you are traveling near or
behind the targeted vehicle and receive an alert,
response time should be sufficient. Any laser
alert, regardless of duration, requires immediate
action!
Complete Band Coverage that detects laser,
radar, VG-2 and safety radar bands.
Laser Facts
It’s well documented that many radar guns
cannot reliably provide the speed of a targeted
vehicle that is traveling in a group of vehicles. In
contrast, a laser gun can target a specific vehicle
out of a line of traffic and determine its speed.
The advantage of laser over radar in terms of
target identification is the result of the laser gun’s
narrow beam. A radar gun’s transmission can
cover more than a four-lane highway at a dis-
tance of 1,000 feet, compared with a laser gun’s
transmission which covers about 3 feet at the
same distance. For best protection, keep these
points in mind:
It is the responsibility of the individual radar detector
owner to know and understand the laws in your area
regarding the legality of the use of radar detectors.
Other Speed Detection Systems
WARRANTY INFORMATION
Several techniques other than radar or laser are
used to measure vehicle speeds. When these
methods are being used, no detector can provide
a warning. These techniques include:
Consumer Warranty
This Whistler Laser-Radar detector is warranted
to the original purchaser for a period of one year
from the date of original purchase against all
defects in materials and workmanship. This
limited warranty is void if the unit is abused,
modified, installed improperly, if the housing and/or
serial numbers have been removed. There are no
expresswarranties covering this product other than
those set forth in this warranty. All express or
implied warranties for this product are limited to the
above time. Whistler is not liable for damages
arising from the use, misuse, or operation of this
product.
• Pacing - A patrol car drives behind you and
matches your driving speed.
• Vascar/Aircraft - The time it takes a vehicle to
travel a known distance is measured.
• Because the vehicle’s license plate or
headlights are the laser gun’s primary targets,
mounting the Whistler detector on the
dashboard can improve laser detection at short
range.
• Do not follow closely behind any vehicle you
cannot see through. If you can’t see past a
vehicle ahead of you, chances are your detector
won’t either.
• The receiving range of your laser detector will
not be the same as a radar detector. Laser guns
are most often used at short range.
Radar Detector Detectors: VG-2,
Spectre
The Interceptor VG-2 or simply VG-2, is one type of
microwave receiver used by Police to detect signals
radiated by the local oscillator of a radar detector.
Because it purpose is to identify persons driving with
radar detectors, these devices are known as a “radar
detector detector” (RDD).
An RDD is the primary tool used by the police to
identify radar detector equipped vehicles. If caught
in a state or country where detectors are illegal (see
page 18), drivers risk losing their radar detector and
receiving a fine. In addition, instant-on radar is
almost always used in combination with a RDD,
leaving unsuspecting motorists vulnerable to receive
two tickets - one potentially for speeding, the other
for possession of a detector.
Whistler Laser-Radar detectors receive all current
laser guns which operate at a laser wavelength of 905
+/- 10mm.
•Pro Laser™ I II III
•LT1 20-20
•Ultra Lyte
20
21
22
WARRANTY INFORMATION
WARRANTY INFORMATION
WARRANTY INFORMATION
ACCESSORIES
3. Be certain your unit is returned with its serial
number. For reference, please write your unit’s
serial number in the following space:
s/n______________.
Important: When returning your unit for service,
be certain to include a daytime telephone
number and an email address (if applicable).
Service Under Warranty
These and other accessories can be
ordered directly from Whistler by calling
1-800-531-0004 or visit our online store at
www.whistlergroup.com
During the warranty period, defective units will
be repaired without charge to the purchaser when
returned with a dated store receipt to the address
below. Units returned without a dated store
receipt will be handled as described in section
“Service Out Of Warranty.”
Due to the specialized equipment necessary for
testing a Laser-Radar receiver, there are no
authorized service stations for Whistler brand
detectors other than Whistler.
Customer Service
Units without serial numbers are not covered under warranty.
If you have questions concerning the operation of your
Whistler detector, or require service during or after the
warranty period, please call Customer Service at:
Important: To validate that your unit is within
the warranty period, make sure you keep a
copy of your dated store receipt. You may
register your warranty online at
Order # Description
Price
1-800-531-0004
Representatives are available to answer your questions
Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT) or
visit the FAQ’s at www.whistlergroup.com.
500501
159032
202151
206552
206553
206880
Zipped Travel Case
$ 9.95
$ 2.95
$ 9.95
$14.95
$15.95
$ 9.95
warranty verification purposes, a copy of
your dated store receipt must accompany any
unit sent in for warranty work.
Package of 8 Suction Cups
Windshield Bracket Kit
Straight Power Cord (5’)
Coiled Power Cord (7’)
When returning a unit for service under
warranty, please follow these instructions:
Service Out of Warranty
Units will be repaired at ‘out of warranty’ service
rates when:
• The unit’s original warranty has expired.
• A dated store receipt is not supplied.
• The unit has been returned without its serial
number.
• The unit has been abused, modified,
installed improperly, or had its housing
removed.
SPECIFICATIONS
Radar Frequencies:
10.500 - 10.550 GHz (X Band)
24.050 - 24.250 GHz (K Band )
33.400 - 36.000 GHz (Ka Superwideband)
1. Ship the unit in the original carton or in a
suitable sturdy equivalent, fully insured, with
return receipt requested to:
Hardwire Kit (10' )
(for wiring to fuse box)
206666
Modular Cord Package
(includes coiled and straight
cords, and power adapter)
$17.95
Whistler Repair Dept.
551 N. 13th St.
Rogers, AR. 72756
Operating Temperature Range:-10˚ C to +70˚ C
(14˚ F to +158˚ F)
402081
206660
Non Skid Dash Pad
$ 6.95
$11.95
Please allow 3 weeks turnaround time.
Important: Whistler will not assume responsi-
bility for loss or damage incurred in shipping.
Therefore, please ship your unit insured with
return receipt requested. CODs will not be
accepted!
Straight Modular Cord &
Socket Multiplier
Power Requirements:
The minimum out of warranty service fee for
your Whistler detector is $55.00 (U.S.). If you
require out of warranty service, please return
your unit as outlined in the section “Service
Under Warranty” along with a certified check or
money order for $55.00. Payment may also be
made by MasterCard, VISA or American
12 volts with power cord.
206661
202152
Coiled Modular Cord &
Socket Multiplier
One or more U.S. patents may apply:
#5,146,227, #5,379,456, #5,666,120, #5,990,821,
#7,215,276
$12.95
$9.95
2. Include with your unit the following
information, clearly printed:
Large Windshield Bracket
• Your name and street address (for
shipping via UPS), a daytime telephone
number and an email address, if applicable.
• A detailed description of the problem (e.g.,
“Unit performs self-test but does not respond
Express; personal checks are not accepted.
POP™ Mode is a trademark of MPH Industries, Inc.
Specifications are subject to change without notice.
SWS™ is a trademark of Safety Warning System L.C.
* Modular: Interconnecting pieces cord and plug.
Shippiing andd handlling (peer ordeer) $5..000 . Priices are
subject tto changee withoutt notice.
In the event repairs cannot be covered by the
minimum $55.00 service fee, you will be contact-
ed by a Whistler technical service specialist who
will outline options available to you.
If you elect not to have your unit repaired, it will
be returned to you along with your certified
check or money order.
`
to radar”).
• A copy of your dated store receipt or bill of
sale.
23
24
25
26
|