Toshiba Automobile Electronics IK TF7 User Manual

INSTRUCTION MANUAL  
3 CCD CAMERA  
IK-TF7  
For Customer Use  
Enter below the Serial No.  
which is located on the  
bottom of the cabinet. Retain  
this information for future ref-  
erence.  
Model No.: IK-TF7  
Serial No.:  
INFORMATION  
This equipment has been tested and found to comply with the limits for a Class A digital device, pursu-  
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be  
required to correct the interference at his own expense.  
USER-INSTALLER CAUTION: Your authority to operate this FCC verified equipment could be voided if  
you make changes or modifications not expressly approved by the party responsible for compliance to  
Part 15 of the FCC Rules.  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est comforme à la norme NMB-003 du Canada.  
IK-TF7(E)  
Page 1  
2004.04.05, 8:50 AMAdobe PageMaker 6.5J/PPC  
 
Caution  
Note the following instructions when installing.  
Do not cover the product by any material.  
Do not put the product on an Inflammable material such as carpet or blanket.  
Do not put the product in a narrow space, since the heat generated from the product  
may be difficult to emanate.  
If you do not follow the above, the heat generated by the product may cause fire.  
Do not put the product in direct sunshine and/or high temperature.  
The temperature inside the product may cause fire.  
Avoid setting in humid, smoky, vaporized or dusty places.  
This may cause fire and/or electric shock.  
Do not point the lens directly at the sun and/or intensive light such as direct sunlight,  
etc.  
Focusing of the light may cause injury of eye and/or fire.  
Ask your dealer to perform a periodical check and internal cleaning (approx. once  
every five years).  
Dust inside the product may cause fire and/or trouble. For check and cleaning cost, please  
consult your dealer.  
Disclaimer  
We disclaim any responsibility and shall be held harmless for any damages or losses incurred by the  
user in any of the following cases:  
1. Fire, earthquake or any other act of God; acts by third parties; misuse by the user, whether inten-  
tional or accidental; use under extreme operating conditions.  
2. Malfunction or non-function resulting in indirect, additional or consequential damages, including  
but not limited to loss of expected income and suspension of business activities.  
3. Incorrect use not in compliance with instructions in this instruction manual.  
4. Malfunctions resulting from misconnection to other equipment.  
5. Repairs or modifications made by the user or caused to be made by the user and carried out by  
an unauthorized third party.  
6. Notwithstanding the foregoing, Toshiba’s liabilities shall not, in any circumstances, exceed the  
purchase price of the product.  
Copyright and Right of Portrait  
There may be a conflict with the Copyright Law and other laws when a customer uses, displays,  
distributes, or exhibits an image picked up by the camera without permission from the copyright  
holder. Please also note that transfer of an image or file covered by copyright is restricted to use  
within the scope permitted by the Copyright Law.  
3
IK-TF7(E)  
Page 3  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
TABLE OF CONTENTS  
1. CAUTIONS ON USE AND INSTALLATION ..... 5 7. 3 External Sync ............................................ 22  
( 1 ) External sync signal input conditions ...... 22  
( 2 ) External sync frequency range ............... 22  
( 3 ) Using the unit with external sync signal .. 23  
(3. 1) H (horizontal) phase adjustment...... 23  
2. COMPONENTS ................................................ 5  
3. ITEMS CONTROLLED BY USING  
ON SCREEN DISPLAY .................................... 6  
( 4 ) Changing HD/VD input/output ................ 23  
4. NAMES AND FUNCTIONS .............................. 7  
5. CONNECTION .................................................. 8  
7. 4 Synchro. Scan Operatin ........................... 23  
( 1 ) Setting by 1H .......................................... 23  
( 2 ) Setting by the frame ................................ 23  
5. 1 Standard Connection ................................ 8  
5. 2 Cautions on Connection ........................... 8  
5. 3 Connector Pin Assignments ..................... 8  
7. 5 EXT TRIG (External trigger) ..................... 24  
( 1 ) 1P SNR (1 Pulse Sync Non Reset) ........ 24  
(1. 1) 1 Pulse Trigger SYNC-NON RESET  
Picture Output Timing ...................... 24  
(1. 2) 1 Pulse Trigger SYNC-NON RESET  
Picture Output Timing (at Time of  
6. OPERATION ..................................................... 9  
6. 1 White Balance........................................... 9  
6. 2 Gain ........................................................ 10  
6. 3 Shading Correction ................................. 10  
Internal Sync) ................................... 25  
7. MODE SETTING BY ON SCREEN DISPLAY ..... 11  
( 2 ) 1P SR (1 Pulse Sync Reset)................... 26  
(2. 1) 1 Pulse Trigger SYNC-RESET Picture  
Output Timing ................................... 26  
7. 1 Using the Menues ................................... 11  
7. 2 Menus ..................................................... 12  
( 1 ) SHUTTER (Electronic shutter)................ 12  
( 3 ) PW SNR (Pulse width trigger  
(1. 1) Changing each setting in  
SYNC-NON RESET) .............................. 27  
(3. 1) Pulse Width Trigger SYNC-NON RESET  
Picture Output Timing ...................... 27  
(3. 2) Pulse Width Trigger SYNC-NON RESET  
Picture Output Timing (at Time of  
MANU mode ..................................... 12  
(1. 2) Changing each setting in  
SS (synchro. scan) mode ................. 13  
(1. 3) Changing each setting in  
E.TRG mode..................................... 14  
(1. 3. 1) Changing each setting in  
1P SNR mode ............................... 14  
(1. 3. 2) Changing each setting in  
1P SR mode ................................. 15  
(1. 3. 3) Changing each setting in  
PW SNR mode ............................. 16  
(1. 3. 4) Changing each setting in  
PW SR mode ................................ 17  
(1. 3. 5) Changing each setting in  
RR mode ....................................... 18  
Internal Sync) ................................... 28  
( 4 ) PW SR (Pulse width trigger  
SYNC-RESET) ....................................... 29  
(4. 1) 1 Pulse Width Trigger SYNC-RESET  
Picture Output Timing ...................... 29  
( 5 ) RR (Reset restart) .................................. 30  
(5. 1) Long Term Exposure ........................ 30  
(5. 2) Input Timing Chart Example ............ 30  
7. 6 Partial Scanning ........................................ 31  
( 1 ) Partial Scanning OFF  
( 2 ) GAIN (Video gain)................................... 18  
(2. 1) Changing each setting in GAIN........ 18  
( 3 ) WHT BAL (White balance)...................... 19  
(3. 1) Changing each setting in AWB  
(All pixels scanning) ................................ 31  
( 2 ) Partial Scanning ON ............................... 31  
( 3 ) When Partial Scanning Mode is ON ....... 31  
8. INPUT OUTPUT SIGNAL SPECIFICATOINS ........ 32  
(Automatic White Balance) mode .... 19  
(3. 2) Changing each setting in MANU  
(Manual) mode ................................. 19  
( 1 ) HD/VD Output Amplitude Specifications ... 32  
( 2 ) VD Input Specifications........................... 32  
( 3 ) VIDEO INDEX Output Specifications..... 32  
( 4 ) HD Input Specifications .......................... 32  
( 5 ) Trigger Pulse Specifications.................... 32  
( 4 ) PROCESS .............................................. 20  
(4. 1) Changing master pedestal ............... 20  
(4. 2) Changing R pedestal ........................ 20  
(4. 3) Changing B pedestal ........................ 20  
(4. 4) Changing White clip .......................... 20  
(4. 5) Changing shading correction mode ... 20  
(4. 6) Changing manual shading correction .. 20  
( 5 ) SYNC ...................................................... 21  
(5. 1) Adjusting horizontal phase ............... 21  
(5. 2) Changing RGB SYNC ...................... 21  
( 6 ) External HD/VD Input Phase  
Specifications.......................................... 32  
9. CCD OUTPUT WAVEFORM TIMING CHART ... 33  
( 1 ) Horizontal Output Waveform Timing Chart ... 33  
( 2 ) Vertical Output Waveform Timing Chart... 33  
( 6 ) OPTION .................................................. 21  
(6. 1) Changing RS232C communication  
baud rate .......................................... 21  
10. SPECIFICATIONS ....................................... 34  
11. EXTERNAL APPEARANCE DIAGRAM ...... 35  
12. BEFORE MAKING A SERVICE CALL ........ 35  
( 7 ) Setting to factory setting status............... 22  
4
IK-TF7(E)  
Page 4  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
1. CAUTIONS ON USE AND INSTALLATION  
Carefully handle the units.  
Handling of the protection cap.  
Do not drop, or give a strong shock or vibration to  
the camera. This may cause problems. Treat the  
camera cables carefully to prevent cable problems,  
such as cable breakdown and loosened connec-  
tions.  
Keep the protection cap away from children. Chil-  
dren may put them into mouth or swallow them  
accidentally. The protection cap protects the im-  
age sensing plane when the lens is removed from  
the camera, do not throw away.  
Do not shoot intense light.  
When not using the camera for a longtime.  
Stop supplying power.  
If there is an intense light at a location on the  
screen such as a spot light, a blooming and smear-  
ing may occur. When intense light enters, vertical  
stripes may appear on the screen. This is not a  
malfunction. Ghosts may occur when there is an  
intense light near the object. In this case, change  
the shooting angle.  
When cleaning the camera.  
Always turn off the power and clean with a piece  
of soft dry cloth. Do not use benzine, alcohol, thin-  
ner, household detergents, chemically treated  
cloths, etc. If used, coating and printed letters may  
be discolored. When cleaning the lens, use a lens  
cleaning paper, etc.  
Install the camera in a location free from noise.  
If the camera or the cables are located near power  
utility lines or a TV, etc. undesirable noise may ap-  
pear on the screen. In such a case, try to change  
the location of the camera or the cable wiring.  
Avoid using or storing the camera in the fol-  
lowing places:  
Places filled with highly flammable gas.  
Places near gasoline, benzene, or paint thinner.  
Places subject to strong vibration.  
Moire  
When thin stripe patterns are shot, stripe patterns  
that are not actually there (moire) may appears  
as interference stripes. This is not a malfunction.  
Places contacting chemicals (such as pesticides),  
rubber or vinyl products for a long period of time.  
Operating ambient temperature and humidity.  
Do not use the camera in places where tempera-  
ture and humidity exceed the specifications. Pic-  
ture quality will lower and internal parts may be  
damaged.  
Be particularly careful when using in places ex-  
posed to direct sunlight. When shooting in hot  
places, depending on the conditions of the object  
and the camera (for example when the gain is in-  
creased), noise in the form of vertical strips or  
white dots may occur. This is not a malfunction.  
2. COMPONENTS  
(1) Camera ...........................................................................................................................................1  
(2) Accessories  
(a) Instruction manual ...................................................................................................................1  
5
IK-TF7(E)  
Page 5  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
3. ITEMS CONTROLLED BY USING ON SCREEN DISPLAY  
Preset value  
(Factory setting)  
Item  
MODE  
E. TRG  
MANU speed  
Available selectins  
MANU, SS, E. TRG  
1P SNR, 1P SR, PW SNR, PW SR, RR  
OFF, 1/100s, 1/250s, 1/500s, 1/1000s, 1/2000s,  
MANU  
1P SNR  
OFF  
1/4000s, 1/10000s, 1/25000s, 1/50000s, 1/1000000s  
Syncro. Partial scanning OFF 1H/796H~795H/796H, OFF, 2FRM~512FRM  
scan. Partial scanning 60fps 1H/387H~386H/387H, OFF, 2FRM~512FRM  
OFF  
OFF  
Partial scanning 90fps  
1H/258H~257H/258H, OFF, 2FRM~512FRM  
OFF, 60 fps, 90 fps  
Partial scanning  
Trigger  
(1P SNR/SR)  
Trigger  
(PW SNR/SR)  
,
,
1P  
16 ms  
0.01ms~16ms  
exposure time  
MODE  
MANU  
MODE  
Color temperature  
MANUAL R GAIN  
MANUAL B GAIN  
Master pedestal  
R pedestal  
MANU, OFF  
-3dB~18dB  
AWB, MANU  
3200K, 5600K  
-100~0~100  
-100~0~100  
-64~0~64  
OFF  
0dB  
AWB  
3200K  
0
0
0
0
-64~0~64  
B pedestal  
White clip  
-64~0~64  
-50~0~50  
0
0
Shading correction  
mode  
MANU, OFF  
MANU  
Manual shading  
correction  
-128~0~127  
0
H phase adjustment  
RGB SYNC  
Baud rate  
-100~0~100  
G ON, ALL ON, ALL OFF  
9600 bps, 19200 bps  
0
ALL ON  
9600 bps  
6
IK-TF7(E)  
Page 6  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
4. NAMES AND FUNCTIONS  
8
2
4
DC IN 12V terminal  
DISP button  
1 Prism faceplate  
MENU UP button  
(AWB)  
DISP  
6
7
DATA UP (AWB) button  
DATA DOWN button  
MENU DATA  
DC IN 12V  
RGB  
PAGE  
5 MENU DOWN button  
9
RGB terminal  
3 PAGE button  
[ Front ]  
[ Rear ]  
Prism faceplate  
The protection cap is attached on the lens mount portion. After removing the cap,  
mount the lens. Be careful not to scratch or touch the optical area.  
1
DISP button  
Used when switching the display.  
2
3
4
5
6
PAGE button  
Used when switching to the menu and when selecting the menus.  
Select the function to be confirmed or changed on the menu.  
Select the function to be confirmed or changed on the menu.  
MENU UP button  
MENU DOWN button  
DATA UP (AWB) button  
Changes the value of the function selected by the MENU (UP/DOWN) button. (Also  
used when using AWB.)  
DATA DOWN button  
DC IN 12V terminal  
RGB terminal  
Changes the value of the function selected by the MENU (UP/DOWN) button.  
Accept a DC power input (12V).  
7
8
9
Used as the connector terminal for RGB output, and SYNC output.  
HD and VD signals are input/output. When the random trigger operation is used,  
the trigger signal is input and the index signal is output. This terminal also includes  
an RS232C format control.  
7
IK-TF7(E)  
Page 7  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
5. CONNECTION  
5. 1 Standard Connection  
Lens  
IK-TF7  
DC IN 12V  
Less than 4 mm  
DC power supply  
5. 2 Cautions on Connection  
• When connecting the camera cables, be sure to turn off the camera and the other equipment connected.  
• We suggest using a C mount lens made for a 3CCD camera.  
When using another lens, the best camera performance of this camera may not be obtained.  
(For example, low resolution may occur, focus may be lost through the range of a zoom lens, and  
flare, ghost or shading may occur)  
Furthermore, in order to avoid damaging the mounting portion of the camera head, use a lens which  
has projection dimension from the mounting base of less than 0.157"(4mm).  
• For DC power supply connecting to DC IN 12V terminal, use UL listed and/or CSA approved ungrounding  
type AC adaptor with the specifications described below.  
Power supply voltage  
Current rating  
Ripple voltage  
Connector  
: DC12V±10%  
: More than 830 mA  
: Less than 50 mV(p–p)  
: HR10A–7P–4S by HIROSE electronics Co. Ltd  
Pins 1, 2 : 12V  
Pins 3, 4 : GND  
5. 3 Connector Pin Assignments  
DC IN 12V  
RGB  
1
R
G
1
2
3
4
+12V  
+12V  
GND  
GND  
2
3
B
1
2
3
4
5
4
3
2
1
4
TXD  
GND  
GND  
GND  
SYNC  
12V  
GND  
RXD  
TRIG  
5
10  
9
8
6
7
6
14 13 12  
15  
11  
7
8
9
10  
11  
12  
13  
14  
15  
HD IN/OUT  
VD IN/OUT  
INDEX  
8
IK-TF7(E)  
Page 8  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
6. OPERATION  
Referring to the item " 5. CONNECTION", connect each equipment correctly.  
Turn on the connected equipment and the camera.  
1
2
3
4
5
Pointing the lens at the object, operate the lens iris adjustment, focus adjustment, etc..  
Referring to the item "6.1 White Balance", operate the adjustment.  
Referring to the items "6.2 Gain, 7. MODE SETTING BY ON SCREEN DISPLAY", select the necessary  
items.  
6. 1 White Balance  
For the white balance adjustment for this unit, AWB (Automatic White Balance) and MANU (Manual white  
balance) adjustments are provided. Referring to the items "7.2 (3) WHT BAL (White balance), 7. MODE SET-  
TING BY ON SCREEN DISPLAY", select the desired mode.  
AWB  
MANU  
(Automatic White Balance)  
(Manual White Balance)  
Outline  
Notes  
Adjust white balance by shooting the white Adjust the white balance manually using  
object inside the area set by AWB menu  
and pressing the [DATA UP] button.  
the WHT BAL menu while shooting the  
white object.  
When the shutter mode is E.TRG, AWB is Adjustment is performed by confirming  
not available. with a waveform monitor.  
AWB (Automatic white balance)  
1
• Set the MODE to AWB on the WHT BAL menu.  
Perform the C.TEMP (color temperature conversion) setting, if necessary.  
(Refer to the item "7.2 (3) WHT BAL (White balance)".)  
3200K : Appropriate for indoor shooting.  
5600K : Appropriate for outdoor shooting.  
• If the index menu/menu is displayed, press the [DISP] button to disable the character display on the  
menu.  
• Shoot a known white object that fills the screen and push [DATA UP] button for approx. 1 second.  
• The character AWB blinks on the screen when the AWB starts.  
• The character AWB stops blinking when the AWB finishes, and the result is displayed for approx. 1  
second.  
Result displayed  
Meaning  
AWB OK  
Automatic white balance adjustment finished correctly.  
AWB NG LEVEL  
LOW  
Automatic white balance adjustment cannot be performed because the  
video level is too low.  
Set the video level properly.  
AWB NG  
LEVEL HIGH  
Automatic white balance adjustment cannot be performed because the  
video level is too high.  
Set the video level properly.  
AWB NG  
C. TEMP HIGH  
Automatic white balance adjustment cannot be performed because the  
color temperature is too low.  
If the C.TEMP is set to 5600K, set to 3200K.  
If the message appears with the C.TEMP set to 3200K, change the  
illumination or use a color temperature conversion filter.  
AWB NG  
C. TEMP HIGH  
Automatic white balance adjustment cannot be performed because the  
color temperature is too high.  
If the C.TEMP is set to 3200K, set to 5600K.  
If the message appears with the C.TEMP set to 5600K, change the  
illumination or use the color temperature conversion filter.  
9
IK-TF7(E)  
Page 9  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
Result displayed  
Meaning  
AWB NG  
NOT AVAILABLE  
Automatic white balance adjustment cannot be performed because the  
shutter speed mode is E.TRG mode.  
AWB NG  
Automatic white balance adjustment cannot be performed for other  
reasons. Such as no white area is included in an object, etc.  
MANU (Manual white balance)  
2
• Set the MODE to MANU on the WHT BAL menu.  
(Refer to the item "7.2 (3) WHT BAL (white balance)".)  
• Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the  
menu, confirming with a monitor or a waveform monitor.  
(Refer to the item "7.2 (3) (3.2) Changing each setting in MANU mode".)  
6. 2 Gain  
When the image is dark even if the lens iris is open, change the gain (video gain) to get the proper video level.  
For the gain adjustment of the unit, MANU (Manual) and OFF (0 dB) modes are provided. Select the mode on  
the GAIN menu. (Refer to the item "7.2 (2) GAIN (Video gain)".)  
MANU (Manual gain)  
1
2
Gain adjustment is performed on the GAIN menu. The adjustment range is from -3dB to 18dB in 1dB steps.  
(Refer to the item "7.2 (2) (2.1) (a) Changing the gain in MANU mode".)  
OFF  
Gain is fixed at 0 dB.  
6. 3 Shading Correction  
Due to the lens used or the environmental condition, vertical color shading may occur at the top and bottom of  
the screen. In this case, the shading correction can decrease the color shading. For the shading correction of  
the unit, MANU (Manual shading correction) and OFF (no shading correction) modes are provided. Select the  
mode on the PROCESS menu. (Refer to the item "7.2 (4) (4.5) Changing shading correction mode".)  
MANU (Manual Shading)  
1
Perform the correction amount setting on the PROCESS menu, confirming with a monitor or a waveform  
monitor. (Refer to the "7.2 (4) (4.6) Changing the manual shading correction setting".)  
OFF  
2
The status is no shading correction.  
* The shading correction is effective when the lens iris or zoom ratio is fixed. Use the unit with SHAD.  
OFF for variable lens conditions.  
10  
IK-TF7(E)  
Page 10  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
7. MODE SETTING BY ON SCREEN DISPLAY  
Various settings can be controlled on the unit by using the on screen menu displayed on the monitor. The  
contents once set are memorized when the power is turned off, so it is unnecessary to set again when using  
the unit next time. When the setting is performed, select the menu of the item to be set.  
7. 1 Using the Menues  
When the power turns on, the normal screen showing only the shooting image appears. Change the output to  
each screen (video signal output, Index menu, and menus) by using the [DISP], [PAGE], [MENU UP], and  
[MENU DOWN] buttons.  
* A menu is selected when pushing the [PAGE] button after moving the "" on the screen by the [MENU UP],  
[MENU DOWN] button while the Index menu is displayed.  
POWER ON  
Video signal output  
Index menu  
DISP  
DISP  
DISP  
PAGE  
PAGE  
Menues  
PAGE  
WHT BAL  
SHUTTER  
GAIN  
PROCESS  
SYNC  
INT  
OPTION  
SHAD.  
MANU  
BAUD  
RATE  
PAGE  
PAGE  
MANU  
PAGE  
AWB  
PAGE  
MANU  
SS  
PAGE  
SHAD.  
OFF  
EXT  
MANU  
OFF  
E. TRG  
1P SR  
E. TRG  
1P SNR  
E. TRG  
PW SR  
E. TRG  
PW SNR  
E. TRG  
RR  
11  
IK-TF7(E)  
Page 11  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
7. 2 Menus  
• Select the menu to change the setting by referring the item "7.1 Using the Menues".)  
• When the [MENU UP], [MENU DOWN] buttons are pushed, the "" on the screen moves up and down.  
Move the "" to the item to change.  
Note:  
When performing the mode setting in the menu display while selecting ON in "PART" and E.TRG in  
"MODE", the display shows normal mode and then the camera returns the setting mode.  
( 1 ) SHUTTER (Electronic shutter)  
The electronic shutter has three modes; MANU (Manual), SS (Synchro. Scan), E.TRG (External trigger).  
Set the "" to "MODE" and push [DATA UP], [DATA DOWN] button to select the desired mode among "MANU",  
"SS", "E.TRG".  
(1. 1) Changing each setting in MANU mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• Shutter speed setting  
OFF, 100 (1/100s), 250 (1/250s), 500 (1/500s)  
1000 (1/1000s), 2000 (1/2000s), 4000 (1/4000s)  
10000 (1/10000s), 25000 (1/25000s)  
MODE  
MANU  
PART  
MANU  
50000  
OFF  
50000 (1/50000s)100000 (1/100000s)  
• Partial scanning switch OFF/60fps/90fps  
<MODE = MANUAL>  
(a) Changing the shutter speed  
Set the "" to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Partial scanning setting  
Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either OFF or 60fps, 90fps by pushing [DATA UP], [DATA DOWN] buttons.  
12  
IK-TF7(E)  
Page 12  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 2) Changing each setting in SS (synchro. scan) mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
• Synchro. scanning setting  
-- SHUTTER --  
OFF : 1H/796H795H/796HOFF2FRM512FRM  
60fps : 1H/387H386H/387HOFF2FRM512FRM  
90fps : 1H/258H257H/258HOFF2FRM512FRM  
MODE  
SS  
PART  
SS  
OFF  
OFF  
• Partial scanning switch OFF/60fps/90fps  
<MODE = SS>  
(a) Changing the shutter speed setting  
Set the "" to SS by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select the shutter speed by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Partial scanning setting  
Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either OFF or 60fps, 90fps by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
13  
IK-TF7(E)  
Page 13  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 3) Changing each setting in E.TRG mode  
The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR.  
First set the "" to MODE and select E. TRG, then set the "" to E.TRG and select the desired E.TRG mode.  
(1. 3. 1) Changing each setting in 1P SNR mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
1P SNR, 1P SR, PW SNR, PW SR, RR  
MODE  
E.TRG  
TRG.P  
EXP.  
PART  
E.TRG  
1P SNR  
• Input trigger pulse setting at 1P SNR and 1P SR  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
16ms  
OFF  
• Exposure time setting at 1P SNR and 1P SR  
0.01 ms  
0.01 ms  
step  
• Partial scanning switch OFF/60fps/90fps  
0.02 ms  
0.02 ms  
step  
0.4 ms  
0.1 ms  
step  
1 ms  
16 ms  
1 ms  
step  
<MODE = E.TRG E.TRG = 1P SNR>  
(a) Changing the polarity of inputting trigger pulse setting  
Set the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing 1P SNR exposure time setting  
Set the "" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
(c) Changing the partial scanning setting  
Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either OFF or 60fps, 90fps by pushing [DATA UP], [DATA DOWN] buttons.  
14  
IK-TF7(E)  
Page 14  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 3. 2) Changing each setting in 1P SR mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
1P SNR, 1P SR, PW SNR, PW SR, RR  
MODE  
E.TRG  
TRG.P  
EXP.  
PART  
E.TRG  
1P SR  
• Input trigger pulse setting at 1P SNR and 1P SR  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
16ms  
OFF  
• Exposure time setting at 1P SNR and 1P SR  
0.01 ms  
0.01 ms  
step  
• Partial scanning switch OFF/60fps/90fps  
0.02 ms  
0.02 ms  
step  
0.4 ms  
0.1 ms  
step  
1 ms  
16 ms  
1 ms  
step  
<MODE = E.TRG E.TRG = 1P SR>  
(a) Changing the polarity of inputting trigger pulse setting  
Set the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing 1P SR exposure time setting  
Set the "" to EXP. by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the exposure time by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
(c) Changing the partial scanning setting  
Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either OFF or 60fps, 90fps by pushing [DATA UP], [DATA DOWN] buttons.  
15  
IK-TF7(E)  
Page 15  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 3. 3) Changing each setting in PW SNR mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
MODE  
E.TRG  
PW SNR  
1P SNR, 1P SR, PW SNR, PW SR, RR  
E.TRG  
TRG.P  
PART  
• Input trigger pulse setting at PW SNR and PW SR  
Input trigger pulse : positive polarity  
OFF  
Input trigger pulse : negative polarity  
• Partial scanning switch OFF/60fps/90fps  
<MODE = E.TRG E.TRG = PW SNR>  
(a) Changing the polarity of inputting trigger pulse setting  
Set the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the partial scanning setting  
Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either OFF or 60fps, 90fps by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
16  
IK-TF7(E)  
Page 16  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 3. 4) Changing each setting in PW SR mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
MODE  
E.TRG  
PW SR  
1P SNR, 1P SR, PW SNR, PW SR, RR  
E.TRG  
TRG.P  
PART  
• Input trigger pulse setting at PW SNR and PW SR  
OFF  
Input trigger pulse : positive polarity  
Input trigger pulse : negative polarity  
• Partial scanning switch OFF/60fps/90fps  
<MODE = E.TRG E.TRG = PW SR>  
(a) Changing the polarity of inputting trigger pulse setting  
Set the "" to TRG.P by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either  
,
by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
17  
IK-TF7(E)  
Page 17  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 3. 5) Changing each setting in RR mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
• Shutter mode MANU, SS, E.TRG  
-- SHUTTER --  
• E.TRG mode  
MODE  
E.TRG  
PART  
E.TRG  
RR  
OFF  
1P SNR, 1P SR, PW SNR, PW SR, RR  
• Partial scanning switch OFF/60fps/90fps  
<MODE = E.TRG E.TRG = RR>  
(a) Changing the partial scanning setting  
Set the "" to PART by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either OFF or 60fps, 90fps by pushing [DATA UP], [DATA DOWN] buttons.  
Note:  
The longer the storage time with extended exposures, the more visible certain characteristics of CCD  
cameras become: fixed pattern noise, white pixels, etc.  
( 2 ) GAIN (Video gain)  
GAIN has two modes; MANU, OFF.  
Set the "" to MODE, push the [DATA UP], [DATA DOWN], and select mode among MANU, OFF. In the OFF  
mode, gain is fixed to 0dB.  
(2. 1) Changing each setting in GAIN  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
-- GAIN --  
MODE  
MANU  
MANU  
0dB  
• Gain mode MANU, OFF  
• Manual gain -3 dB to 18 dB (10 dB step)  
(a) Changing the gain in MANU mode  
Set the "" to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the manual gain by pushing [DATA UP], [DATA DOWN] buttons.  
18  
IK-TF7(E)  
Page 18  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 3 ) WHT BAL (White balance)  
WHT BAL has two modes; AWB, MANU.  
Set the "" to MODE, push the [DATA UP], [DATA DOWN], and select mode among AWB, MANU.  
(3. 1) Changing each setting in AWB (Automatic White Balance) mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
-- WHT BAL --  
MODE  
C.TEMP  
AWB  
3200  
• White balance mode setting (AWB, MANU)  
• Color temperature setting 3200, 5600  
(a) Changing color temperature setting  
Set the "" to C.TEMP by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either 3200 or 5600 by pushing [DATA UP], [DATA DOWN] buttons.  
(3. 2) Changing each setting in MANU (Manual) mode  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
-- WHT BAL --  
MODE  
MANU  
• White balance mode AWB, MANU  
• Red gain adjustment -100 to 100  
• Blue gain adjustment -100 to 100  
• Color temperature setting 3200, 5600  
R GAIN  
B GAIN  
C. TEMP  
0
0
3200  
(a) Changing the red gain  
Set the "" to R GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the red gain by pushing [DATA UP], [DATA DOWN] buttons.  
(b) Changing the blue gain  
Set the "" to B GAIN by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the blue gain by pushing [DATA UP], [DATA DOWN] buttons.  
19  
IK-TF7(E)  
Page 19  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 4 ) PROCESS  
Move up down  
By pushing  
MENU UP, DOWN  
Set by pushing  
DATA UP, DOWN  
-- PROCESS --  
• Master pedestal adjustment -64 to 64  
• R pedestal adjustment -64 to 64  
M.PED  
R.PED  
B.PED  
W.CLP  
SHAD.  
MANU  
0
0
0
0
• B pedestal adjustment -64 to 64  
• White clip adjustment -50 to 50  
• Shading mode setting MANU/OFF  
• Manual shading adjustment -128 to 127  
MANU  
0
(4. 1) Changing master pedestal  
Set the "" to M. PED by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the master pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 2) Changing R pedestal  
Set the "" to R. PED by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the R pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 3) Changing B pedestal  
Set the "" to B. PED by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the B pedestal by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 4) Changing White clip  
Set the "" to W. CLP by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the W. CLP by pushing [DATA UP], [DATA DOWN] buttons.  
Note: The alignment value for shading is fixed to "0" when selecting SHAD. OFF. MANU is not dis-  
played in the menu.  
(4. 5) Changing shading correction mode  
Set the "" to SHAD. by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the SHAD. by pushing [DATA UP], [DATA DOWN] buttons.  
(4. 6) Changing manual shading correction  
Set the "" to MANU by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Set the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.  
20  
IK-TF7(E)  
Page 20  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 5 ) SYNC  
When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external  
sync) automatically.  
Move up down  
Set by pushing  
By pushing  
MENU UP, DOWN  
DATA UP, DOWN  
-- SYNC --  
MODE  
H PHASE  
EXT  
0
• Sync system display  
• H PHASE -100 to 100  
RGB SYNC  
G ON  
• RGB SYNC G ON, ALL ON, ALL OFF  
(5. 1) Adjusting horizontal phase  
Set the "" to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.  
(5. 2) Changing RGB SYNC  
Set the "" to RGB SYNC by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select G ON, ALL ON or ALL OFF by pushing [DATA UP], [DATA DOWN] buttons.  
( 6 ) OPTION  
Move up down  
By pushing  
MENU UP, DOWN  
Set by pushing  
DATA UP, DOWN  
-- OPTION --  
BAUD RATE  
9600  
• RS232C baud rate 9600, 19200  
(6. 1) Changing RS232C communication baud rate  
Set the "" to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.  
1
2
Select either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.  
21  
IK-TF7(E)  
Page 21  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 7 ) Setting to factory setting status  
The contents set of each scene file can be returned to the factory default status (preset status).  
(1) If characters are displayed on the screen, press the [DISP] button to disable the character display.  
(2) Push [MENU DOWN] and [DATA DOWN] buttons simultaneously for approx. 1 second.  
(3) The preset operation starts. When the preset operation finishes, the character PRESET OK is displayed  
for approx. 1 second.  
7. 3 External Sync  
When using the unit with an external sync signal, input HD and VD to RGB terminal on the rear panel. When  
the external sync signal is input, the camera automatically switches its sync from the internal sync to the  
external sync.  
The operation is as shown below, depending on the unit's status and how external sync signals are input.  
Shutter mode  
At time of SYNC-NON  
RESET mode  
HD input VD input  
Note  
N
Y
N
Y
N
Y
Y
N
Internal sync mode  
External sync mode  
Only V reset is applied due to VD input. Normally not used.  
HD is synchronized to external, but video is not output  
because there is no VD input. Normally not used.  
At time of SYNC-RESET  
mode  
N
Y
*
*
Internal sync mode. The presence of VD is ignored, and after  
a specified time after a trigger input, V reset is applied.  
HD is synchronized to external. The presence of VD is  
ignored, and after a specified time after a trigger input, V  
reset is applied.  
At time of reset restart  
Y
N
*
Y
Y
N
HD is synchronized to external. Video is output due to VD  
input.  
HD is synchronized to the inside of the camera. Video is  
output due to VD input.  
Video is not output because there is no VD input. Normally  
not used.  
At time of manual  
shutter  
N
Y
Y
N
N
Y
N
Y
Internal sync mode  
External sync mode  
HD is synchronized to external. Normally not used.  
Disabled  
* Either Y or N is permitted.  
( 1 ) External sync signal input conditions  
HD: 2 to 5V(p-p) Negative  
VD: 2 to 5V(p-p) Negative  
( 2 ) External sync frequency range  
(External sync with HD, VD)  
Within ±1% (at horizontal sync frequency of 23.229 kHz)  
22  
IK-TF7(E)  
Page 22  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 3 ) Using the unit with external sync signal  
When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horizontal phase".  
External  
Sync. signal  
(3. 1) H (horizontal) phase adjustment  
Match  
the phase.  
Observe the external sync signal and the video signal output  
waveform of the unit with a dual trace oscilloscope, and ad-  
just H phase so that the H phases match.  
Camera  
Video output  
( 4 ) Changing HD/VD input/output  
(1) Put off 6 screws both on flank/top of camera chassis.  
(2) Change internal switch SJ01(HD/VD).  
HD/VD OUTPUT  
HD/VD INPUT high-impedance  
HD/VD INPUT 75(factory setting)  
7. 4 Synchro. Scan Operatin  
The shutter speed can be set by the horizontal scanning period (1H) or by the frame.  
( 1 ) Setting by 1H  
1H/796H to 795H/796H (1H/387H to 386H/387H when partial scanning at 60fps, 1H/258H to 257H/258H when  
partial scanning at 90fps) stands for the setting by the 1H and the shutter speed can be set by the 1H (43.05  
µs).  
( 2 ) Setting by the frame  
2FRM to 512FRM stand for the setting (long period exposure) by the frame.  
The video signal stored during the frame period set is output as 1 frame video image at a frame interval  
specified.  
VD output  
n
n+1  
Video putput  
Index output  
(INDEX)  
(4FRM setting)  
23  
IK-TF7(E)  
Page 23  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
7. 5 EXT TRIG (External trigger)  
Charge begins to accumulate after the trigger input, and 1 frame images are output. There are five modes: 1P  
SNR, 1P SR, PW SNR, PW SR, RR.  
The RGB terminal trigger input and index output interface are as shown below.  
5V  
15kΩ  
1SS357  
150Ω  
(CMOS out)  
Trigger input  
INDEX out  
( 1 ) 1P SNR (1 Pulse Trigger Sync Non Reset)  
Charge begins to accumulate after the trigger input to the RGB terminal, and 1 frame images are output.  
(1. 1) 1 Pulse Trigger SYNC-NON RESET Picture Output Timing  
(At Time of One-shot or Continuous External VD/Continuous External HD Input)  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 1 µs  
Exposure period*2  
Exposure period*2  
External HD IN*1  
External VD IN*1  
About 1H  
(Internal VD)  
VIDEO INDEX  
Video output  
The internal VD falling edge is within the exposure  
period and thus video is not output.  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps)  
258H (Partial scanning 90fps)  
3
*
*1: Externally input signal  
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and the VIDEO INDEX have a paired relationship.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
24  
IK-TF7(E)  
Page 24  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(1. 2) 1 Pulse Trigger SYNC-NON RESET Picture Output Timing (at Time of Internal Sync)  
Negative polarity mode  
Positive polarity mode  
Trigger*1  
About 1 µs  
Exposure period*2  
Exposure period*2  
VD OUT*3  
VIDEO INDEX  
Video output  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps)  
258H (Partial scanning 90fps)  
*1: Externally input signal  
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".  
As long as there is no external sync input, the internal VD will be output when SJ01 is set to HD/VD output  
position.  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and the VIDEO INDEX have a paired relationship.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
25  
IK-TF7(E)  
Page 25  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 2 ) 1P SR (1 Pulse Trigger Sync Reset)  
Charge begins to accumulate after the trigger input to the RGB terminal, the vertical sync signal is reset and  
frame images are output.  
(2. 1) 1 Pulse Trigger SYNC-RESET Picture Output Timing  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 1 µs  
Exposure period*2  
Exposure completion  
0 to 1H*3  
VD OUT  
Video output  
VIDEO INDEX  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps)  
258H (Partial scanning 90fps)  
*1: Externally input signal  
*2: Exposure time is determined by the setting of "7. 2 (1.3) Changing each setting in E.TRG mode".  
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchro-  
nized to this and output.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
26  
IK-TF7(E)  
Page 26  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET)  
The trgger input to the RGB terminal develops 1 frame images.  
(3. 1) Pulse Width Trigger SYNC-NON RESET Picture Output Timing  
(At Time of One-shot or Continuous External VD/Continuous External HD Input)  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 7 µs  
About 1 µs  
Exposure period*2  
Exposure period*2  
External HD IN*1  
External VD IN*1  
About 1H  
(Internal VD)  
VIDEO INDEX  
Video output  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps) period and thus video is not output.  
258H (Partial scanning 90fps)  
The internal VD falling edge is within the exposure  
3
*
*1: Externally input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and the VIDEO INDEX have a paired relationship.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
27  
IK-TF7(E)  
Page 27  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
(3. 2) Pulse Width Trigger SYNC-NON RESET Picture Output Timing (at Time of Internal Sync)  
Negative polarity mode  
Trigger*1  
Positive polarity mode  
About 7 µs  
About 1 µs  
Exposure period*2  
Exposure period*2  
VD OUT*3  
VIDEO INDEX  
Video output  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps)  
258H (Partial scanning 90fps)  
*1: Externally input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: As long as there is no external sync input, the internal VD will be output when SJ01 is set to HD/VD output  
position.  
*4: Video is output at the falling edge of the internal VD following completion of the exposure period.  
The video and the VIDEO INDEX have a paired relationship.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
28  
IK-TF7(E)  
Page 28  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 4 ) PW SR (Pulse width trigger SYNC-RESET)  
The trgger input to the RGB terminal develops 1 frame images.  
(4. 1) 1 Pulse Width Trigger SYNC-RESET Picture Output Timing  
Negative polarity mode  
Positive polarity mode  
Trigger*1  
About 1 µs  
About 7 µs  
Exposure period*2  
Exposure completion  
0 to 1H  
3
*
VD OUT  
Video output  
VIDEO INDEX  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps)  
258H (Partial scanning 90fps)  
*1: Externally input signal  
*2: Exposure time = Trigger pulse width + 6 µs  
(Valid trigger pulse width is 2 µs or greater for external trigger shutter operation.)  
*3: VD is generated after 0 to 1H following the completion of the exposure period and the video is synchro-  
nized to this and output.  
Note:  
When the next trigger is input before completion of the output of the video corresponding to the trig-  
ger, there will be an effect on the video.  
29  
IK-TF7(E)  
Page 29  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
( 5 ) RR (Reset restart)  
Input of an external reset-restart signal (VD terminal) permits one screen of information to be output at an  
arbitrary timing.  
(5. 1) Long Term Exposure  
When the camera is used and sufficient sensitivity cannot be obtained for the reset-restart function under  
normal operating conditions, or when observation of the trail of a moving subject is desired, the exposure time  
can be extended to allow high-sensitivity images to be obtained. To achieve this, please input from an external  
source a VD signal that has an expanded VD pulse and VD pulse interval.  
(5. 2) Input Timing Chart Example  
External HD IN  
External VD IN  
V reset  
V reset  
About 1H  
About 1H  
(Internal VD)  
Exposure period  
Exposure period  
Exposure period  
VIDEO OUT  
VIDEO INDEX  
1 frame  
External VD interval: more than 1 frame  
1 frame  
30  
IK-TF7(E)  
Page 30  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
7. 6 Partial Scanning  
( 1 ) Partial Scanning OFF (All pixels scanning)  
In this mode, all pixels independent signal from the VIDEO OUT connector is output with increased flame rate.  
External HD/VD sync is permitted.  
Frame image  
Frame image  
Frame image  
1/29.2s (796H)  
( 2 ) Partial Scanning ON  
In this mode, the pixel signal of the vertical center portion from the VIDEO OUT connector is output.  
External HD/VD sync is permitted.  
1/60s (387H):when 60fps is selected  
1/90s (258H):when 90fps is selected  
( 3 ) When Partial Scanning Mode is ON  
VD  
9H  
Video output  
Blanking interval  
B
Video interval Blanking interval  
C
D
Total  
A
Video period C  
Mode  
60fps  
90fps  
Total A  
387  
Blanking interval B Video interval C Blanking interval D  
38  
47  
322  
175  
27  
36  
258  
31  
IK-TF7(E)  
Page 31  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
8. INPUT OUTPUT SIGNAL SPECIFICATOINS  
( 1 ) HD/VD Output Amplitude Specifications  
( 4 ) HD Input Specifications  
HD  
4.5V  
2.0 to  
5.0 V(p-p)  
0V  
5H to 21H  
4.5V  
VD  
* Input impedance: 75or 10kor greater  
0V  
* Input amplitude 2.0 to 5.0 Vp-p (75termination ON  
The amplitude level is the representative value when  
terminated with 10k.  
Output is enabled when the internal switch SJ01 is set  
to the OUT side.  
or OFF)  
* Voltage and pulse width were measured at RGB con-  
nector located on the rear panel.  
( 5 ) Trigger Pulse Specifications  
2.0 to  
5.0 V(p-p)  
2
5.0V  
2.0 µs to 5.0 µs  
0
0.4V  
(Positive polarity mode)  
More than 2 µs  
( 2 ) VD Input Specifications  
* Input impedance: 75W or 1kor greater  
2
0
5.0V  
0.4V  
* Input amplitude 2.0 to 5.0 V(p-p) (75termination ON  
or OFF)  
(Negative polarity mode)  
* Voltage and pulse width were measured at RGB con-  
nector located on the rear panel.  
More than 2 µs  
* Input impedance: 10kor greater  
4.5V  
* Voltage and pulse width were measured at RGB  
connector located on the rear panel.  
0V  
796H (Partial scanning OFF)  
387H (Partial scanning 60fps)  
258H (Partial scanning 90fps)  
( 3 ) VIDEO INDEX Output Specifications  
The amplitude level is the representative value when  
terminated with 10kW.  
( 6 ) External HD/VD Input Phase Specifications  
External HD  
rising edge  
100  
100  
External HD  
Unit : Clock  
1 clk=33.9nsec  
Center  
The phase relationship of the external HD and VD should correspond to the center phase (i.e., the external HD falling  
edge) as illustrated in the above diagram.  
External VD falling edge:  
Please input within about 100 clock cycles of the standard center phase.  
Note that V sync of the video is output with a delay of about 1H from the external VD at the time of reset-restart and  
the external trigger mode.  
In the normal mode:  
Continuously with the HD period of 43.05 µs and VD period of 34.27 ms (partial scanning 60fps: 16.67 ms, partial  
scanning 90fps: 11.11 ms ).  
Phase timing is as illustrated in the above diagram (with only the falling edge applicable).  
In the reset-restart/external trigger mode:  
Continuously with the HD period of 43.05 µs. VD (reset) is at an arbitrary timing with the phase of HD being within the  
standard of the above diagram.  
32  
IK-TF7(E)  
Page 32  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
9. CCD OUTPUT WAVEFORM TIMING CHART  
( 1 ) Horizontal Output Waveform Timing Chart  
One horizontal scan interval 1270 clk  
(43.05 µs)  
HD  
102 clk  
(3.46µs)  
33.9 ns  
29 clk 3 clk  
40 clk  
164 clk  
CCD  
output signal  
5 clk  
5
clk  
Optical black Horizontal transfer Dummy  
portion  
stop interval  
pixels  
Total effective pixels 1034 clk  
Optical black  
portion  
Horizontal blanking interval 246 clk  
Output video interval 1024 clk  
(8.34 µs)  
(34.71 µs)  
Video  
output signal  
(Representative  
values)  
HSYNC  
73 clk  
22 clk  
151 clk  
(5.12 µs)  
CLK=33.9 nsec  
(0.75 µs) (2.47 µs)  
( 2 ) Vertical Output Waveform Timing Chart  
796H  
9H  
9H  
387μs)  
387μs)  
VD  
HD  
768  
CCD  
output signal  
1
1
2
3
4
5
6
7
1
1
2
3
4
5
6
7
Dummy  
pixels  
Dummy  
pixels  
Optical black  
portion  
Optical black  
portion  
Optical black  
portion  
Optical black  
portion  
Video  
Vertical blanking interval 28H  
Vertical blanking interval 28H  
output signal  
(Representative  
values)  
(1205 µs)  
(1205 µs)  
33  
IK-TF7(E)  
Page 33  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
10. SPECIFICATIONS  
Power supply  
DC12V±10%  
Power consumption  
Pick-up system  
Approx.4.3W  
RGB, 3CCD  
Image sensor  
1/3inch All pixels CCD  
(Effective pixels)  
(Horizontal : 1034pixels, Vertical : 779pixels)  
Scanning system  
Scan frequency  
Sync system  
Progressive scan  
Horizontal : 23.229kHz, Vertical : 29.18Hz  
Internal/External (Automatic switching)  
768TV lines  
F6.8 standard (2000 lx, 3000K)  
14 lx (F2.2, Sensitivity + 18 dB, 3000K)  
C mount (flange back : 17.526 mm in-air)  
32 to 104°F (0 to 40°C)  
Horizontal resolution  
Sensitivity  
Minimum illumination  
Lens mount  
Ambient temperature  
Ambient humidity  
Weight  
Less than 90%  
Approx. 5.82oz (165g)  
External dimension  
1.73” (W) x 1.73” (H) x 3.07” (D)  
(44 (W) x 44 (H) x 78 (D) mm)  
(except for protruded portion)  
White balance  
Gain  
AWB (Automatic white balance), MANUAL (Manual)  
MANUAL (Manual), OFF (0 dB)  
Output signal  
External sync input  
Sync signal output  
RGB : 1.0V(p-p) 75unbalanced, D sub 15 pin connector  
HD or VD :  
2 – 5 V(p-p) Negative  
SYNC :  
HD, VD, INDEX :  
2.0V±1 V(p-p) 75unbalanced  
5V+0.5  
-1.0  
V(p-p), Negative  
Load impedance : More than 10 kW  
Interface  
Serial data interface (RS-232C)  
EXC-TF05B (RGB cable), etc  
Optional parts  
34  
IK-TF7(E)  
Page 34  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
11. EXTERNAL APPEARANCE DIAGRAM  
Unit : mm [inch]  
5
2-M3 Depth 3  
44  
78  
6.3  
12  
(AWB)  
DISP  
PAGE  
DATA  
MENU  
DC IN 12V  
RGB  
5
No.4-40UNC  
4-M3 Depth 3  
5
56  
4-M2 Depth 3  
25  
25  
12. BEFORE MAKING A SERVICE CALL  
Symptom  
Items to be checked  
No image  
• Is the power supplied correctly?  
• Is the lens iris adjusted correctly?  
• Are the cables connected correctly?  
• Is the shutter mode set correctly?  
• Is the image process equipment set correctly?  
Poor color  
• Is the monitor adjusted correctly?  
• Is the white balance of the camera adjusted correctly?  
• Is the illumination dark?  
35  
IK-TF7(E)  
Page 35  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 
LIMITED WARRANTY  
TOSHIBA CCD CAMERA  
uct you will be eligible for periodic updates, announcements, and special offers. You will have access to extended  
warranty options, upgrades (as applicable), useful tips, on-line troubleshooting, and the ability to schedule service  
on-line if necessary. The Imaging Systems Division of Toshiba America Information Systems, Inc. ("ISD") makes  
the following limited warranties. These limited warranties extend to the Original End-User ("Your[r]").  
Limited One (1) Year Warranty of Labor and Parts  
ISD warrants this product and parts against defects in material or workmanship for a period of one year from the  
date of original retail purchase by the end-user. During this period, ISD will repair or replace a defective product or  
part with a new or refurbished item. The user must deliver the entire product to an ISD authorized service center.  
The user is responsible for all transportation and insurance charges for the product to the Service Center. ISD  
reserves the right to substitute Factory Refurbished Parts and / or Factory Refurbished Product in place of those  
in need of repair.  
Step-by-step Procedures - How to Obtain Warranty Service  
[1] Verify operation of the unit by checking the instruction manual  
[2] If there is a defect in material or workmanship, contact an Authorized Service Provider within 30 days after the  
product fails to comply with specifications.  
[3] Arrange for delivery of the product to the ISD authorized service center. Products must be insured and securely  
packed, preferably in the original shipping carton. A letter explaining the defect and a copy of the bill of sale or  
other proof of purchase must be enclosed with a complete return street address and daytime telephone number.  
Charges for transportation and insurance must be prepaid by the end-user.  
Questions? If you have any questions, please check the Toshiba Imaging Systems Division Web site as  
follows:  
Website:  
Your Responsibility, warranties are subject to the following conditions:  
[1] You must retain the bill of sale or provide other proof of purchase.  
[2] You must schedule service within thirty days after you discover a defective product or part.  
[3] All warranty servicing of this product must be made by a Toshiba ISD Authorized Service Provider.  
[4] The warranty extends to defects in material or workmanship as limited above, and not to any products or parts  
that have been lost or discarded by user. The warranty does not cover damage caused by misuse, accident,  
improper installation, improper maintenance, or use in violation of instructions furnished by ISD. The warranty  
does not extend to units which have been altered or modified without authorization of ISD, or to damage to prod-  
ucts or parts thereof which have had the serial number removed, altered defaced or rendered illegible.  
ALL WARRANTIES IMPLIED BY STATE LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT-  
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF  
THE LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply. WITH THE EXCEPTION OF ANY WARRAN-  
TIES IMPLIED BY STATE LAW AS HEREBY LIMITED, THE FOREGOING EXPRESS WARRANTY IS EXCLU-  
SIVE AND IN LIEU OF ALL OTHER WITH RESPECT TO THE REPAIR OR REPLACEMENT OF ANY PROD-  
UCTS OR PARTS. IN NO EVENT SHALL ISD BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAM-  
AGES. Some states do not allow the exclusion or limitation of incidental or consequential damages so the  
above limitation may not apply.  
No person, agent, distributor, dealer, service station or company is authorized to change, modify or ex-  
tend the terms of these warranties in any manner whatsoever. The time within which an action must be  
commenced to enforce any obligation of ISD arising under this warranty or under any statute, or law of the  
United States or any state thereof, is hereby limited to one year from the date you discover or should have  
discovered, the defect. This limitation does not apply to implied warranties arising under state law. Some  
states do not permit limitation of the time within which you may bring an action beyond the limits provided  
by state law so the above provision may not apply to user. This warranty gives the user specific legal  
rights, and user may also have other rights, which may vary from state to state.  
TOSHIBA AMERICA INFORMATION SYSTEMS, INC.  
Imaging Systems Division  
Copyright © 2002 Toshiba America, Inc. All rights reserved.  
IK-TF7(E)  
Page 36  
2004.04.05, 8:51 AMAdobe PageMaker 6.5J/PPC  
 

TDK Power Supply Power Supply DC to DC Converter CCFL Inverter User Manual
Technics Stereo System SL MC4 User Manual
Tektronix Network Card Spectrum Analyzer User Manual
Trane Air Conditioner PKG SVX17A EN User Manual
Tri M Systems Computer Hardware MOPS 586 User Manual
Tripp Lite Power Supply APS1024INT User Manual
Turbo Chef Technologies Oven 2020 HIGH h User Manual
ViewSonic Computer Monitor VA2342 LED User Manual
ViewSonic Flat Panel Television CD4200 User Manual
ViewSonic Projector PJ501 User Manual