Sharp Computer Monitor PNL601BPKG User Manual
PN-L601B  
LCD MONITOR  
TOUCH PANEL DRIVER  
OPERATION MANUAL  
 
Setting up the PC  
To use the touch panel, the touch panel driver must be installed from the supplied CD-ROM and the touch panel must be  
connected to your PC.  
Installing the touch panel driver  
The touch panel driver is a program that enables you to use to the touch panel to operate the PC that is connected to the touch  
panel. Settings for touch panel operation can also be configured.  
Caution  
• This can only be done by a user with administrator authority.  
• If an older version of the touch panel driver is installed, remove (uninstall) the old version before installing the touch panel  
driver. (See page 8.)  
• If you are using a USB hub, use a self-powered hub (a hub capable of supplying a 500 mA current). The touch panel will not  
operate correctly if a bus-powered USB hub is used.  
• Do not connect the USB cable until after you have installed the touch panel driver.  
• Do not touch the touch panel when connecting the USB cable.  
If you touch the touch panel, this may be detected as an element failure in the infrared transmitter/receiver and malfunctioning  
will result. In this case, disconnect and then reconnect the USB cable.  
1. Start your PC.  
2. Exit all applications that are running.  
3. Insert the supplied CD-ROM into the CD-ROM drive of your PC.  
4. Open the CD-ROM drive in “Computer” or “My Computer”.  
5. Double-click the “TouchPanel” folder.  
6. Double-click the install file.  
• If you are using a 32-bit operating system, double-click “TPdrvSetup_x86.msi”.  
• If you are using a 64-bit operating system, double-click “TPdrvSetup_x64.msi”.  
7. Click “Next”.  
Follow the on-screen instructions to install the driver.  
• When the “User Account Control” screen appears, click “Yes” (or “Allow”).  
• If the “Windows Security” screen appears, click “Install this driver software anyway”.  
• If the “Software Installation” screen appears, click “Continue Anyway”.  
8. When the installation finished screen appears, click “Close”.  
9. If a screen appears prompting you to restart your PC, click “Yes”.  
10. After your PC starts, connect the USB cable for the touch panel to the PC.  
After it has been connected, the touch panel will be automatically recognized and enabled for use.  
To the USB terminal  
of the PC  
USB cable (Supplied)  
This completes the installation of the touch panel driver.  
Each time the PC is started, the touch panel driver will start automatically to enable the touch panel to be used.  
The first time you use the touch panel, perform calibration (position adjustment). (See page 5.)  
TIPS  
• The touch panel will not operate correctly unless the touch panel driver is running.  
• If the touch panel driver is not running, it can be started by double-clicking “SH_TPdrv.exe” in the folder where the touch  
panel driver is installed. The touch panel driver is normally installed in the following folder:  
C:\Program Files\SHARP\SH_TPdrv (when the PC’s startup drive is the C drive)  
E
3
 
 
Touch Panel Settings  
Touch panel settings are configured in the touch panel driver.  
The touch panel driver starts automatically and the icon (  
) appears on the taskbar.  
Caution  
• When using the touch panel, set the “SIZE” of the monitor to “WIDE”, “NORMAL”, or “Dot by Dot”.  
The touch panel cannot be used when the “SIZE” is set to “ZOOM1” or “ZOOM2”.  
How to configure settings  
1. Click the touch panel driver icon (  
2. Click a menu to change a setting.  
) on the taskbar.  
• Current Screen Resolution: The current screen resolution appears.  
• Calibration: See page 5.  
• Properties: See page 6.  
• Hardware Information: Select this to specify “Test Information Display”, “Rotate Mode”, and “Disable TP Driver”. (Normally  
not used.)  
-Test Information Display: Select to view operating conditions. (For service technicians.)  
-Rotate Mode: Select when the image has been rotated on a PC that has a video card capable of image rotation.  
-Disable TP Driver: Select to disable the touch panel function.  
• Version Information: Shows the version of the touch panel driver.  
• Exit: Exit the touch panel driver. (When this is selected, it will no longer be possible to use the touch panel function.)  
E
4
 
 
Touch Panel Settings  
Calibration  
Calibration is used to perform position alignment so that the mouse cursor moves to the correct position when the screen is  
touched.  
Calibration Method  
n
Simple  
Select the currently displayed screen size (“WIDE”, “NORMAL”, “Dot by Dot”), and calibration takes place automatically.  
Calibrate using advanced calibration if the mouse cursor is out of position when the touch pen is used.  
TIPS  
• When a key has been assigned to the “Easy Change” hot key setting, the key can be pressed to successively change a  
setting.  
Advanced  
Calibration can be performed manually. Click “OK” to open the settings. Follow the on-screen instructions. (To cancel during  
calibration, press the [ESC] key on the keyboard.)  
Hot Key Setting  
n
Hot keys can be set to perform the operations below. The [Ctrl] and [Shift] keys are fixed as hot keys. One of the A to Z or 0 to 9  
keys can be selected for the third hot key.  
Easy Change : The calibration method can be changed to “Simple” by pressing the hot key. Settings can be successively  
changed by pressing the hot key.  
Calibration  
: The hot key can be pressed to open the SELECT CALIBRATION screen.  
E
5
 
 
Touch Panel Settings  
Properties  
Settings for the touch pen can be configured in the properties. Select a tab to change a setting on that tab.  
DOUBLE CLICK RANGE SETTING  
n
Set how much the position can shift between the first touch and the second touch and still be recognized as a double-click. Set  
the range based on how you use the touch pen. To return the setting to the default setting, click “Default”.  
TIPS  
• Changing this setting also changes the effective double-click range when the mouse is used.  
DOUBLE CLICK SPEED SETTING  
n
Set the time that is recognized as a double-click. When a second touch occurs within the set time after the first touch, it is  
recognized as a double-click.  
SPEED SETTING (Auto)  
The inside of the frame can be touched twice (double-clicked) to set the speed automatically based on the interval between the  
touches.  
Set Manually  
The speed can be set manually from “Slow” (about 1 second) to “Fast” (about 0.3 seconds).  
TEST  
When the inside of the frame is double-clicked by touching it twice, the screen changes. If the screen does not change, repeat  
the setting.  
Default  
Click to restore the default setting.  
TIPS  
• Changing this setting also changes the mouse double-click speed of Windows.  
• Depending on the software application, changing the setting may not have any effect (for example, if the setting is set  
separately in the application).  
E
6
 
 
Touch Panel Settings  
OPERATION SETTING  
n
Function Button 1  
Set the function that activates when function button 1 is pressed with the touch pen.  
• RightClick : Functions as a right click.  
• Disable  
: Disables function button 1.  
Function Button 2  
Set the function that activates when function button 2 is pressed with the touch pen.  
• Pen Software Link : Functions as a link button for a Pen Software function.  
• Disable  
TIPS  
: Disables function button 2.  
• The Pen Software function that links to function button 2 is set in the Pen Software.  
Input Mode Setting  
Set the input mode for the touch panel. It is normally recommended that you use “Standard”.  
• Standard  
• HandWrite : Select this when you only wish to use your finger and will not be using the touch pen function.  
• Pen : Select this for operation by touch pen only. Only the touch pen can be used; your finger cannot be used.  
: Automatically switches between pen mode and handwriting mode.  
Detect Eraser Area  
Specify whether the area (rectangle) of a touched item is detected. The application must support area detection.  
Resolution Change Notice  
• Enable : When the screen resolution is changed, a message is displayed regarding the calibration setting.  
• Disable : When the screen resolution is changed, the previously set calibration values are automatically applied. When a  
resolution is used for the first time, the message regarding the calibration setting will appear.  
Optimize HTML  
For normal operation and writing text by hand, this setting is not necessary.  
When manipulating a document with a small click range for HTML links, enable this and adjust the effective “Click range”.  
E
7
 
Uninstalling the Driver Software  
Caution  
• This can only be done by a user with administrator authority.  
1. Click the touch panel driver icon (  
) on the taskbar and click “Exit”.  
If a confirmation window appears, click “Yes”.  
2. Disconnect the USB cable.  
3. Select “Control Panel” from the “Start” menu.  
4. Click “Uninstall a program”.  
• If you are using icon view (Classic View), double-click “Programs and Features”.  
• In Windows XP, click “Add or Remove Programs”. (In the “Classic View”, double-click “Add or Remove Programs”.)  
5. Remove “Touch Panel Driver”.  
Follow the on-screen instructions.  
6. If a screen appears prompting you to restart your PC, restart your PC.  
This completes the uninstallation.  
E
8
 
 
PN-L601B D EN 10H(1)  
 

Sharp Air Cleaner FU W28E User Manual
Sharp Air Cleaner KC 850U User Manual
Sony Computer Monitor GDM FW900 User Manual
Sony DVR ICD UX60 User Manual
Sony Ericsson MP3 Player Walkman player User Manual
Sony Garage Door Opener KV 32FV1 User Manual
Sony Speaker SA FT7ED User Manual
Sony Stereo System STR SL7 User Manual
Sony VCR SLV SE840G User Manual
Swann Security Camera StyleCam User Manual