ENGLISH
Polar FT60 User Manual
ENGLISH
1. GET STARTED
Get to Know Your Polar FT60
The Polar FT60 training
computer records and
displays your heart rate and
other data during training.
The Polar H1 heart rate
sensor transmits the heart
rate signal to the training
computer. The heart rate
sensor consists of a
connector and a strap.
The latest version of this
user manual can be
downloaded at
Register your Polar product
and help us improve our
products and services to
better meet your needs.
Start With Basic Settings
To activate your Polar FT60, press and hold any button for one second. Once the FT60 is activated, it
cannot be switched off.
1. Language: Select Deutsch, English, Español, Fr
, Italiano, Português or Suomi with UP/DOWN.
Press OK.
2. Please enter basic settings is displayed. Press OK.
3. Select Time format.
4. Enter Time.
5. Enter Date.
6. Select Units, metric (KG, CM) or imperial (LBS, FT). By selecting lbs/ft, calories are displayed as CAL,
otherwise they are shown as KCAL. Calories are measured as kilocalories.
7. Enter Weight.
8. Enter Height.
9. Enter Date of birth.
10. Select Sex.
11. Settings OK? is displayed.
Select Yes to accept and save the settings. Basic settings complete is displayed and the FT60 enters
Time mode.
Select No if you want to change the settings. Please enter basic settings is displayed. Re-enter your
basic settings.
To modify your personal settings later, see Settings.
Get Started
3
ENGLISH
Buttons and Menu Structure
UP: Enter the menu and move
through selection lists, adjust values
OK: Confirm selections, select
training type or training settings
DOWN: Enter the menu and move
through selection lists, adjust values
BACK:
view
LIGHT:
training (to adjust training sounds or lock buttons)
Symbols on the Display
The following table presents the display symbols and their descriptions.
Symbol
Description
The battery of the training computer is low.
The alarm is active.
Sounds are off.
Time 2 is in use. Number two is displayed at the lower right corner of the
display.
You have one or more new messages.
The button lock is active.
The footpod is in use. If the symbol is blinking, the FT60 is trying to establish
a connection with the footpod.
The GPS sensor is in use. If the symbol is blinking, the FT60 is trying to
establish a connection with the GPS sensor, or the GPS sensor is trying to
establish a connection with the satellites.
Heart rate is transmitted.
4
Get Started
ENGLISH
2. BEFORE TRAINING
Activate Your Polar Star Training Program
The adaptive, personalized and in-built Polar Star Training Program gives you the optimal intensity and
time targets for your training. The training computer gives feedback on your performance after each
training session and once a week.
The Polar FT60 creates a training program based on your user information (weight, height, age, sex),
fitness level, activity level, and training goal.
By analyzing your weekly training results and fitness level, the training computer gives you training
guidance for the following week. The training program adapts to your training habits and to your changing
fitness level.
1. In Time mode, select Menu > Applications > Training program > Create new program .
2. Perfom Polar Fitness Test. For more information, see Test Your Fitness Level.
3. Select your training goal:
Improve fitness if your target is to improve your current cardiovascular fitness level and you are able
to train regularly.
Maximize fitness if your target is to maximize your current cardiovascular fitness level, and if you have
been training regularly for at least 10-12 weeks and training nearly every day is not a problem for you.
Lose weight if your target is to lose some weight.
4. Training program created! is displayed.
5. Next, View week targets? is displayed. Select YES to view the time and calorie targets for your first
training week. If you select No, Training program active! is displayed and the training computer returns
to Time view.
Time target
The amount of time you should train during this week.
Calorie target
The number of calories you should burn this week.
6. Press DOWN and OK to view your target training time in three different heart rate zones (intensity
targets). Press DOWN to change the display.
Time target for intensity zone 1
The bars indicate the target times in different intensities. The bars fill up as you
train. The target time for intensity zone 1 for the week is displayed in the lowest row.
7. You have now activated your training program. Press BACK to return to Time mode.
To view your week targets later, select Menu > Applications > Training Program > View week targets .
Zone
Intensity % of HRmax
Training benefit
Zone 3
80-90%
Zone 2
70-80%
sessions with moderate length
Before Training
5
ENGLISH
Zone 1
60-70%
muscles, light sweating
Troubleshooting
User information missing is displayed > Enter the missing user information.
Fitness test result required is displayed > You need to perform the Fitness Test.
Change/End your program
Menu > Applications > Training program > Change
program. For instance, if you have started with weight loss program and have achieved your goal, change
your goal to Improve Fitness or Maximize Fitness.
Menu > Applications > Training program > End program >
End Program? Select Yes.
To view the results of your previous program:
Select Menu > Applications > Training program > Results of past prog. The following information is
displayed:
Start date and Duration: The start date and the duration of the training program.
Excel. wks and Calories: The number of excellent training weeks (100% of target reached) vs. total
number of training weeks and the calories expended during the program.
Before/After: Your Fitness Test result (OwnIndex) or your weight (when weight loss program active)
before and after the program.
Test Your Fitness Level
To train right and to monitor your progress, it is important to know your current fitness level. The Polar
Fitness TestTM is an easy and quick way to measure your cardiovascular fitness. The test is performed at
rest.
As a result you will get a value called OwnIndex. OwnIndex is comparable to maximal oxygen uptake
(VO2max ), which is a commonly used aerobic fitness measure. Read more on how to interpret the results in
Interpret Your Fitness Test Results.
The OwnIndex value also affects the accuracy of the training program and calorie calculation during
training.
The test is developed for healthy adults. To make sure the test is reliable, take the following issues into
consideration:
accurate the test result will be (for instance, no television, telephone or talking).
day before.
Perform Polar Fitness Test
1. Wear the heart rate sensor, lie down and relax for 1-3 minutes.
6
Before Training
ENGLISH
2. In Time mode, select Menu > Applications > Fitness test > Start test. The fitness test begins instantly
once the FT60 has located your heart rate.
3. About 5 minutes later, a beep will indicate the end of the test, and your test result will appear on the
display.
4. Press OK. UPDATE VO
? is displayed.
2max
5. Select Yes to save the test result in your User information and OwnIndex results. If you know your
laboratory measured VO2max value and have entered it in User information, select No to save your test
result in OwnIndex results only.
Troubleshooting
Set activity lev. of past 3 months is displayed > Set your activity level (see Settings for more information
on activity levels). Activity set! is displayed and the test begins.
Test Failed is displayed or no heart rate shown > Test fails. Check that the heart rate sensor electrodes are
moist enough and that the elastic strap is snug enough around your chest. If the fitness test fails, your
previous OwnIndex value is not replaced.
Interpret your fitness test results
Interpret the OwnIndex
values by comparing your
individual values and their
progression over time.
OwnIndex can also be
interpreted based on gender
and age. Locate your
OwnIndex on the table, and
find out your fitness level
class and how your aerobic
fitness compares to others
of the same gender and age.
This classification is based on a
literature review of 62 studies
where VO2max was measured
directly in healthy adult subjects
in the USA, Canada and 7
European countries. Reference:
Shvartz E, Reibold RC: Aerobic
fitness norms for males and
females aged 6 to 75 years: a
review. Aviat Space Environ
Med; 61:3-11, 1990.
Before Training
7
ENGLISH
3. TRAINING
Wear the Heart Rate Sensor
Wear the heart rate sensor to measure heart rate.
1. Moisten the electrode area of the strap.
2. Attach the connector to the strap.
3. Tie the strap around your chest, just below the chest
muscles, and attach the hook to the other end of the
strap.
4. Adjust the strap length to fit tightly but comfortably.
Check that the moist electrode areas are firmly
against your skin and that the Polar logo of the
connector is in a central and upright position.
Detach the connector from the strap and rinse the strap
under running water after every use. Sweat and moisture
may keep the electrodes wet and the heart rate sensor
activated. This will reduce the heart rate sensor battery
life. For more detailed washing instructions, see Important
Information.
Start Training
1. Wear the training computer and heart rate sensor.
2. In Time mode press OK and select Start or long-press OK once when you want to start recording your
training session.
To modify sound, heart rate view or other training settings before recording your training session, select
Training Settings. See Settings for more information
Your training session is recorded only if the stopwatch has been on for more than one minute.
Start Training With OwnZone
Starting every training session with the OwnZone guarantees safe and effective heart rate zones for your
daily condition. Check your OwnZone at least
Determining OwnZone limits take five minutes, and can be performed as a warm-up. Start slowly keeping
your heart rate below 100 bpm/ 50% HRmax. After each minute, increase your speed gradually about 10
bpm/ 5% HRmax
.
If you have activated your training program and you actively use the OwnZone determination, the training
computer unit takes into account your long-term OwnZone results when updating the program targets.
1. Wear the training computer and heart rate sensor.
2. Press OK and select Start with OwnZone.
8
Training
ENGLISH
3. At some point during OwnZone determination, New limits in use is displayed. Proceed normally with your
training.
Troubleshooting
Previous limits in
use is displayed. If you have not determined your OwnZone limits, Age-based limits in use is displayed.
The OwnZone determination fails if the heart rate rises too fast during the OwnZone determination, or if
the heart rate is too high at the beginning of the test.
During Training
The following information can be displayed during training recording. Press UP/DOWN to change the view.
Session duration is displayed in all views.
Heart rate
Your heart rate during training.
Calories
Burned calories.
In zone 1, 2 or 3
Training time in zone and your heart rate. Smiley face means that OwnZone
determination was succesfull.
If your heart rate is not within the zones, NOT IN ZONE is displayed.
Week target (displayed if training program is active)
Weekly target for each zone and the actual training time.
Speed
Optional GPS sensor or footpod required to view speed data.
Distance
Optional GPS sensor or footpod required to view distance data.
Training
9
ENGLISH
Time of day
Lock a zone: Depending on your goal for a training session, you can lock zone 1, 2 or
3 during the session. When you are training in a desired zone, lock it by pressing OK
for one second. For instance, when you have achieved your weekly target for zones 2
and 3, you can lock zone 1. The zone alarm helps you stay inside the locked zone.
For example, zone 2 is locked in this image.
Quick Menu: Long pressing LIGHT during recording brings you to Quick menu. The Quick menu is a short
cut to locking buttons, adjusting training sounds, and if footpod is in use, calibrating it.
Heart Touch: Check the time during training recording by bringing the training computer near the heart
rate sensor. Set Heart Touch function On/Off in Settings > Training Settings > HeartTouch .
Stop Training Recording
To pause your training session, press BACK.
To stop the training session press BACK twice and Stopped is displayed.
For more information on instant, training session feedback, see Follow-Up Your Achievements.
Training feedback will be shown only if the training session has lasted for ten minutes or longer.
10
Training
ENGLISH
4. AFTER TRAINING
Training Feedback
The training computer provides you with the following feedback after a training session.
Effect
Training effect feedback. See Table 1 for more information.
Intensity
Time spent in zones 1, 2, and 3.
Zone limits
OwnZone limits (displayed if OwnZone in use).
Calories
Expended calories during the session, and fat percentage.
Average /Maximum
Average and maximum heart rate during training session.
Average /Maximum*
Average and maximum speed of training session (displayed only if optional
GPS/footpod in use).
Distance*
Distance and duration of training session (displayed only if optional
GPS/footpod in use).
This week
Your targets for the current training week and the results you have achieved
so far. This information is only visible when the program is active.
*Optional GPS sensor or Footpod required to view speed and distance data.
Table 1.
Feedback
Fat burn improving
Training at low intensity is improving your body's ability to burn fat.
Training at moderate intensity is improving your fitness.
Fitness improving
Maximal perform. improving
Training at hard intensity is improving your maximal performance.
If you are training enough at more than one intensity level, training will have several effects.
Fat burn and fitness improving
Fitness and fat burn improving
Max. perf. and fitness improving
Weekly Follow-up
Training is primarily improving your body's ability to burn fat, but it also
improves your fitness.
Training is primarily improving your fitness, but also your body's ability to burn
fat.
Training is improving your fitness and maximal performance.
Every Sunday at midnight, an envelope with the week's results will appear on the display of your training
computer. Press UP to view.
Week targets achieved
Tells you whether or not you have achieved the week's targets.
After Training
11
ENGLISH
Results
Excellent! / Well done! / Nice! / Fitness maintained / Incomplete training
week / Good recovery week / Excellent recovery week
If your result is excellent, the FT60 rewards you with a trophy. The
trophy appears in the time mode display.
Achieved/Week target
Achieved/Week target
Sessions
Achieved training duration vs. week target duration
Expended calories vs. week target
The number of training sessions achieved this week (also displayed without a
program).
Achieved time per zone
This week
Time spent in intensity zones 1, 2, and 3.
Training guidance for the starting week displayed only when accessed from
the envelope. See Table 2 for more information.
Table 2.
Training guidance for the starting week
Train a lot more
You need to train a lot more to get effects.
You do not train enough for improvement.
Train more
Train more in zone X
Train like last week!
Train less in zone X
Train much less in zone 3
Recovery week
You need to train more in this zone.
You did a good job last week. Keep it up!
You should decrease training in this zone.
You should train less in hard intensity zone this week.
You need recovery to avoid overreaching.
Recovery week still needed
Train as planned
You have not recovered yet; last week was still too hard.
You have had a good start, continue training according to the program.
Weight Update
If you are following the weight loss program, the FT60 will remind you to update your weight by displaying
an envelope once a week.
1. Time to check your weight is displayed. Press OK.
2. Set current weight? appears. Select Yes to update your weight.
Fitness Test
As soon as you reach your training targets, the FT60 will post an envelope reminding you to take a fitness
test. The result of the test is taken into account in the weekly program update.
1. Time to test fitness is displayed.
2. Test fitness? appears. Select Yes or No.
3. If you decide to take a new test, see Test Your Fitness Level for more information.
12
After Training
ENGLISH
Program Update
Polar FT60 continuously analyzes your progress and adjusts by increasing or decreasing weekly targets. An
envelope appears on the display to notify you when the program has been updated. Press UP to open the
envelope.
1. Program has been updated is displayed: the FT60 has analyzed your progress and adapted your program
targets accordingly.
2. Time for a recovery week is displayed: To optimize your training, you need to have an ideal balance
between training and recovery. Recovery week allows your body to improve and adapt to the stimulus that
training has provided.
Weight Diary
In the weight diary, you can monitor your weight loss and view your progress over a period of time. To
update your weight, select Menu > Applications > Weight diary > Set current weight. Set your weight and
press OK. Your current weight will also be updated in User information.
To view your weight trend, select Menu > Applications > Weight diary > Weight trend and press OK.
Weight trend
The weight and the date on which it was entered.
The weight trend including the lowest and highest weight.
To delete a value, select the value you want to delete with UP/DOWN. When the value is displayed, press
and hold LIGHT until Delete this value? is displayed. Select Yes.
Follow Your fitness Test Results
On average, it takes six weeks of regular training to improve your aerobic fitness noticeably. To improve
your aerobic fitness most efficiently, you need to train large muscle groups. Monitor your long-term test
results under the OwnIndex results, containing 47 of your latest OwnIndex values and the date the tests
were performed.
1. Select Menu > Applications > Fitness test > OwnIndex results.
2. The latest OwnIndex result and the date of the test is displayed. Press UP/DOWN to view the previous
OwnIndex results.
OwnIndex
The date and the result of the test
Your OwnIndex result graph with the lowest and highest OwnIndex value
To delete an OwnIndex value, select the value you want to delete with UP/DOWN. When the value is
displayed, press and hold LIGHT until Delete this value? is displayed. Select Yes.
Review Training Data
Review your training data in Training files, Week summaries and Totals.
1. Select Data > Training files to view detailed training information on your 100 most recent training
sessions. The information is similar to what is displayed after each training session.
After Training
13
ENGLISH
Each bar represents one training session. Select a training session you
wish to view.
Upper row: Date and time of day when the file was created
Lower row: Training time
When Training files becomes full, the oldest training file is replaced by the most recent one. If you want
further information, see Transfer Data.
To delete a training file, select Data > Delete files and the file you want to delete. Delete file? is
displayed. Select Yes. Remove from total? is displayed. To remove the file from totals, as well, select
Yes.
2. Select Data > Week summaries to view the training data and results for the last 16 weeks.
Each bar represents one training week. Select a week you wish to view with
UP/DOWN.
Upper row: Week start / Week end date
Lower row: Total training time
To reset week summaries select Data > Reset weeks?. Select Yes to reset week summaries.
3. Select Data > Totals since xx.xx.xxxx to view the total cumulative duration, number of training sessions
and calories starting from the last reset.
To reset totals, select Data > Reset totals and select Yes.
Transfer Data
How to transfer data from your FT60 to polarpersonaltrainer.com
For long-term follow-up, you can store all your training files at polarpersonaltrainer.com. There you can see
graphs and more of your training data and get a better understanding of your training. With Polar
FlowLink* it is easy to transfer the training files to the web service.
1. Register in polarpersonaltrainer.com
2. Follow instructions to download and install WebSync data transfer software onto your computer.
3. Polar WebSync software is automatically activated and instructions for downloading the data are
displayed on your computer. Follow the instructions and your training data is transferred to
polarpersonaltrainer.com web service.
4. Place your FT60 onto FlowLink display facing down.
5. Follow data transfer process from the WebSync Software on your computer screen. For further
instructions on data transfer, see polarpersonaltrainer.com "Help".
*Optional Polar FlowLink required.
14
After Training
ENGLISH
5. SETTINGS
Watch Settings
Select the value you want to change and press OK. Adjust the values with UP/DOWN and accept with OK.
Select Settings > Watch, time and date.
Alarm: Set the alarm to go on Once, from Monday to Friday, Every day, or turn it Off. Press BACK to stop
the alarm or UP/DOWN to snooze for 10 minutes. The alarm cannot be used during training.
Time: Select Time 1 and set the time format, hours and minutes. Select Time 2 to set time for another time
zone by adding or substracting hours. In the Time view, you can quickly change from Time 1 to Time 2 by
pressing and holding DOWN.
Time zone: Select time zone 1 or 2.
Date: Set the date.
Watch face: Select Time and logo, Time and trophy or Time only.
Training Settings
Select Settings > Training settings.
Training sounds: Select Very loud, Loud, Soft or Off.
Speed sensor: Activate or deactivate speed and distance sensor by selecting GPS sensor, Footpod or Off.
Heart rate view : Set the FT60 to display your heart rate as Beats per minute or as Percent of maximum.
Speed view: Select Kilometres per hour (KM/H) / Minutes per kilometre (MIN/KM) or Miles per hour
(MPH) / Minutes per mile (MIN/M)
Footpod calib. factor: For more information, see Accessory settings.
HeartTouch: Select On or Off.
Zone lock: Select Zone 1, 2 0r 3 to train on a specific heart rate zone or set the zone lock Off.
Zone 1 Limits: Adjust your zone 1 limits manually. When setting the upper limit, the lower limit of zone 2
is set automatically.
Zone 2 limits: Adjust your zone 2 limits manually. When setting the lower limit, the upper limit of zone 1
is set automatically. When setting the upper limit, the lower limit of zone 3 is set automatically.
Zone 3 limits: Adjust your zone 3 limits manually. When setting the lower limit, the upper limit of zone 2
is set automatically.
Change the zone limits defined by Polar FT60 only if you know your limits for burning fat, improving fitness and
maximizing fitness. If the training program is active, the FT60 will incorporate your new zone limits when updating
the program targets.
User Information
Select Settings > User Information and press OK.
Weight: Enter your weight.
Height: Enter your height.
Date of birth: Enter your date of birth
Sex : Select MALE or FEMALE.
Maximum heart rate is the highest number of heartbeats per minute (bpm) during maximum physical
exertion. Change the default value only if you know your laboratory-measured value.
Activity: Select the alternative that best describes the overall amount and intensity of your physical
activity during the past three months.
1. TOP (5+ hours per week): You participate in heavy physical exercise at least 5 times a week, or you
exercise to improve performance for competitive purposes.
2. HIGH (3-5 hours per week): You participate at least 3 times a week in heavy physical exercise, e.g.
you run 20-50 km or 12-31 miles per week or spend 3-5 hours per week in comparable physical
activity.
3. MODERATE (1-3 hours per week): You participate regularly in recreational sports, e.g. you run 5-10 km
Settings
15
ENGLISH
or 3-6 miles per week or spend 1-3 hours per week in comparable physical activity, or your work
requires modest physical activity.
4. LOW (0-1 hours per week): You do not participate regularly in programmed recreational sport or heavy
physical activity, e.g. you walk only for pleasure, or exercise hard enough to cause heavy breathing or
perspiration only occasionally.
OwnIndex (VO2max): When you perform the Polar Fitness Test, your OwnIndex value is shown as a default.
Change the default value only if you know your laboratory-measured VO2max value.
General Settings
Select Settings > General settings .
Button sounds: Select Off, Soft, Loud or Very loud.
Button lock: Select Manual lock or Automatic lock.
Automatic lock: The training computer automatically locks all the buttons except LIGHT during training.
You can switch the button lock off by pressing and holding LIGHT until Buttons unlocked is displayed.
Manual lock: To lock buttons manually, press and hold LIGHT and confirm with OK. To unlock press
LIGHT until Buttons unlocked is displayed.
Units: Select Metric (kg/km) or Imperial (lb/ft). By selecting lb/ft, calories are displayed as Cal,
otherwise they are shown as kcal.
Language: Select Deutsch, English, Español, Fr
or Suomi.
Accessory Settings
Footpod Calibration*
Calibrate Foot Pod during training (on-the-fly calibration)
Make sure the foot pod function in the Polar FT60 is on. Select Settings > Training settings > Speed
sensor > Footpod and press OK.
To calibrate the footpod during training, choosing either alternative:
1. Stop running, stand still, and press and hold LIGHT to go to Quick menu.
OR
2. Stop running, stand still, and press BACK once.
Select Calibrate footpod. Fix the displayed distance with the actual distance you just run, and press OK.
Calibration factor set! is displayed. The foot pod is now calibrated and ready for action.
Set Calibration Factor Manually
There are two options for setting the calibration factor manually:
1. Before training: Select Settings > Training settings > Footpod calib. factor . Set the calibration factor
and press OK. The foot pod is now calibrated.
2. After starting heart rate measurement and before training recording: In the time mode, press OK and then
select Training settings > Footpod calib. factor . Set the calibration factor and press OK. The foot pod is
now calibrated. To start training recording press BACK once and then select Start.
*Optional S1 foot pod required.
16
Settings
ENGLISH
6. IMPORTANT INFORMATION
Caring for Your Product
Like any electronic device, the Polar training computer should be treated with care. The suggestions below
will help you fulfill guarantee obligations and enjoy this product for many years to come.
Connector: Detach the connector from the strap after every use and dry the connector with a soft towel. Clean the connector
with a mild soap and water solution when needed. Never use alcohol or any abrasive material (eg. steel wool or cleaning
chemicals).
Strap: Rinse the strap under running water after every use and hang to dry. Clean the strap gently with a mild soap and
water solution when needed. Do not use moisturizing soaps, because they can leave residue on the strap. Do not soak, iron,
dry clean or bleach the strap. Do not stretch the strap or bend the electrode areas sharply.
Check the label on your strap to see if it is machine washable. Never put the strap or the connector in a dryer!
Training computer and sensors: Keep your training computer and sensors clean. To maintain the water
resistance, do not wash the training computer or the sensors with a pressure washer. Clean them with a
mild soap and water solution and rinse them with clean water. Do not immerse them in water. Dry them
carefully with a soft towel. Never use alcohol or any abrasive material such as steel wool or cleaning
chemicals.
Keep your training computer and sensors in a cool and dry place. Do not keep them in a damp
environment, in non-breathable material (a plastic bag or a sports bag) nor with conductive material (a wet
towel). The training computer and heart rate sensor are water resistant, and can be used in water
activities. Other compatible sensors are water resistant, and can be used in rainy weather. Do not expose
the training computer to direct sunlight for extended periods, such as by leaving it in a car or mounted on
the bike mount.
Avoid hard hits to the training computer and the sensors, as these may damage the sensor units.
Service
During the two-year guarantee/warranty period we recommend that you have service done by an authorized Polar Service
Center only. The warranty does not cover damage or consequential damage caused by service not authorized by Polar
Electro.
Changing Batteries
The FT60 training computer and the Polar H1 heart rate sensor both have a user changeable battery. To change the battery
yourself, please follow the instructions carefully as instructed in chapter Change Batteries Yourself.
Prior to changing the batteries, please note the following:
the appearance of the low battery indicator will remain active.
Change Batteries Yourself
When changing the battery, make sure the sealing ring is not damaged, in which case you should replace it with a new
one. You can purchase the sealing ring/battery kits at well-equipped Polar retailers and authorized Polar Services. In the
USA and Canada, the additional sealing rings are available at authorized Polar Service Centers. In the USA the sealing
Keep the batteries away from children. If swallowed, contact a doctor immediately.
Batteries should be properly disposed of according to local regulations.
When handling a new, fully charged battery, avoid clasp-like contact, i.e. simultaneous from both sides, with metal or
electrically conducting tools, like tweezers. This may short-circuit the battery causing it to discharge more rapidly.
Typically, short circuiting does not damage the battery, but it may decrease the capacity and lifetime of the battery.
Changing Training Computer Battery
Important Information
17
ENGLISH
Open the battery cover with a coin by turning it from
1.
2.
CLOSE to OPEN.
Remove the battery cover and lift the battery out
carefully with a suitable sized small rigid stick or bar,
such as a toothpick. A non-metal tool is preferable. Be
careful not to damage the metal sound element (*) or
the grooves. Insert a new battery with the positive (+)
side outwards.
Replace the old sealing ring with a new one (if
available), fitting it snugly in the cover groove to ensure
water resistance.
3.
Put the cover back on and turn clockwise to CLOSE.
4.
5.
Please enter basic settings is displayed. Press and
hold the BACK button to skip the Basic settings.
If you re-enter the Basic Settings, the training computer
thinks there is a new user and the STAR Program is
turned off.
Go to Settings mode and adjust time and date.
To return to Time mode, press and hold the BACK
button. Now your FT60 can be used normally.
6.
7.
Changing Polar H1/H2/H3 Heart Rate Sensor Battery
1. Lever the battery cover open by using the clip on the
strap.
2. Remove the old battery from the battery cover with a
suitable sized small ridgid stick or bar, such as a
toothpick. A non-metal tool is preferable. Be careful not
to damage the battery cover.
3. Insert the battery inside the cover with the negative (-)
side outwards. Make sure the sealing ring is in the groove
to ensure water resistance.
4. Align the ledge on the battery cover with the slot on the
connector and press the battery cover back into place.
You should hear a snap.
Changing Polar WearLink+ Heart Rate Sensor Battery
1. Using a coin, open the battery cover by turning it
counterclockwise to OPEN.
2. Insert the battery inside the cover with the
negative (-) side outwards. Make sure the sealing
ring is in the groove to ensure water resistance.
3. Press the cover back into the connector.
4. Use the coin to turn the cover clockwise to
CLOSE.
Danger of explosion if the battery is replaced with wrong type.
Precautions
The Polar training computer shows your performance indicators. It indicates the level of physiological
strain and intensity during your training session. No other use is intended or implied.
18
Important Information
ENGLISH
Minimizing Risks When Training
Training may include some risk. Before beginning a regular training program, answer the following
questions concerning your health status. If you answer yes to any of these questions, consult a physician
before starting any training program.
In addition to exercise intensity, medications for heart conditions, blood pressure, psychological
conditions, asthma, breathing, etc., as well as some energy drinks, alcohol, and nicotine may also affect
heart rate.
It is important to be sensitive to your
If you feel unexpected pain or
excessive fatigue when exercising, it is recommended that you stop the exercise or continue at a lighter
intensity.
Note! If you are using a pacemaker, you can use Polar training computers. In theory interference to
pacemaker caused by Polar products should not be possible. In practice no reports exist to suggest anyone
ever having experienced interference. We cannot however issue an official guarantee on our products'
suitability with all pacemakers or other implanted devices due to the variety of devices available. If you
have any doubts, or if you experience any unusual sensations while using Polar products, please consult
your physician or contact the implanted electronic device manufacturer to determine safety in your case.
If you are allergic to any substance that comes into contact with your skin or if you suspect an allergic
reaction due to using the product, check the listed materials in Technical Specifications. To avoid any
skin reaction to the heart rate sensor, wear it over a shirt, but moisten the shirt well under the electrodes
to ensure flawless operation.
The combined impact of moisture and intense abrasion may cause a black color to come off the heart rate
surface, possibly staining light-colored clothes. If you use perfume or insect repellent on your skin, you must
ensure that it does not come into contact with the training computer or the heart rate sensor.
Training equipment with electronic components may cause interfering stray signals. To tackle these
problems, try the following:
1. Remove the heart rate sensor from your chest and use the training equipment as you would normally.
2. Move the training computer around until you find an area in which it displays no stray reading or does not
flash the heart symbol. Interference is often worst right in front of the display panel of the equipment,
while the left or right side of the display is relatively free of disturbance.
3. Put the heart rate sensor back on your chest and keep the training computer in this interference-free area
as much as possible.
If the FT60 still does not work, the piece of equipment may be electrically too noisy for wireless heart rate
measurement.
Polar FT60 may be worn when swimming. To maintain water resistance, do not press buttons under water.
according to International Standard ISO 2281. Products are divided into three categories according to
their water resistance. Check the back of your Polar product for the water resistance category, and
compare it to the chart below. Please note that these definitions do not necessarily apply to products of
other manufacturers.
Important Information
19
ENGLISH
Marking on case back
Water resistant
Water resistant characteristics
Protected against wash splashes, sweat, raindrops
etc. Not suitable for swimming.
Water resistant 30 m/50 m
Water resistant 100 m
Suitable for bathing and swimming
Suitable for swimming and snorkeling (without air
tanks)
Troubleshooting
If you don't know where you are in the menu, press and hold BACK until the time of day is displayed.
If there are no reactions to any buttons or the training computer displays unusual readings, reset the training computer by pressing four
buttons (UP, DOWN, BACK and LIGHT) simultaneously for four seconds. All other settings but time and date are saved.
If the heart rate reading becomes erratic, extremely high or shows nil (00), make sure that there are no other heart rate sensors within
1 m/3 ft and that the strap/the textile electrodes fit snugly and are wet, clean and undamaged.
If the heart rate measurement does not work with the sports apparel, try measuring using the strap. If it works, the problem
is most probably in the apparel. Please contact the apparel retailer/manufacturer.
Strong electromagnetic signals can cause erratic readings. Electromagnetic disturbances may occur near high-voltage
power lines, traffic lights, overhead lines of electric railways, electric bus lines or trams, televisions, car motors, bike
computers, some motor driven training equipment, cellular phones, or at electric security gates. To avoid erratic readings,
move away from possible sources of disturbance.
If the abnormal reading continues despite moving away from the source of disturbance, slow down and check your pulse
manually. If you feel it corresponds to the high reading on the display, you may be experiencing cardiac arrhythmia. Most
cases of arrhythmia are not serious, but consult your doctor nevertheless.
A cardiac event may have altered your ECG waveform. In this case, consult your physician.
If heart rate measurement fails despite the actions mentioned previously, the battery of your heart rate sensor may be
empty.
Technical Specifications
Training Computer
CR2025
Battery type
Battery life
Average 1 year (1 h/day, 7 days/week exercise)
Operating temperature
Wrist strap material
Back cover and wrist strap buckle
-10
Silicone (white model) / Polyurethane (other models)
Stainless steel complying with the EU Directive 94/27/EU and amendment 1999/C 205/05 on
the release of nickel from products intended to come into direct and prolonged contact with
the skin.
Watch accuracy
Accuracy of heart rate measurement
Better than ± 0.5 seconds/day at 25
± 1% or ± 1 bpm, whichever larger, definition applies to steady state conditions.
Heart Rate Sensor
CR 2025
Battery type
Battery life (Polar WearLink)
Battery life (Polar H1)
Average 700 hours of use
Average 1500 hours of use
Battery cap sealing ring (Polar WearLink)
Battery cap sealing ring (Polar H1)
Operating temperature
Connector material (Polar WearLink)
Connector material (Polar H1)
Strap material (Polar WearLink)
Strap material (Polar Soft strap)
O-ring 20.0 x 1.0 Material FPM
O-ring 20.0 x 0.90 Material Silicone
-10
Polyamide
ABS
35% Polyester, 35% Polyamide, 30% Polyurethane
38% Polyamide, 29% Polyurethane, 20% Elastane, 13% Polyester
Limit values
23 h 59 min 59 s
15 - 240 bpm
0 - 9999 h 59 min 59 s
0 - 999999 kcal/Cal
65 535
Chronometer
Heart rate
Total time
Total calories
Total exercise count
Year of birth
1921 - 2020
Maximum speed with a GPS sensor
Maximum speed with footpod
199.9 km/h
29.5 km/h
Polar FlowLink and Polar WebSync 2.1 (or newer)
PC MS Windows (7/XP/Vista), 32 bit, Microsoft .NET Framework Version 2.0
Intel Mac OS X 10.5 or newer
System Requirements:
20
Important Information
ENGLISH
The Polar FT60 training computer applies the following patented technologies, among others:
OwnZone® assessment for determining personal target heart rate limits for the day
OwnCode® coded transmission
OwnIndex® technology for fitness test
OwnCal® personal calorie calculation
FlowLink® data transfer
Limited International Polar Guarantee
This guarantee does not affect the consumer
consumer
This limited Polar international guarantee is issued by Polar Electro Inc. for consumers who have purchased this product in
the USA or Canada. This limited Polar international guarantee is issued by Polar Electro Oy for consumers who have
purchased this product in other countries.
Polar Electro Oy/Polar Electro Inc. guarantees the original consumer/purchaser of this device that the product will be free
from defects in material or workmanship for two (2) years from the date of purchase.
The receipt of the original purchase is your proof of purchase!
The guarantee does not cover the battery, normal wear and tear, damage due to misuse, abuse, accidents or
non-compliance with the precautions; improper maintenance, commercial use, cracked, broken or scratched
cases/displays, armband, elastic strap and Polar apparel.
The guarantee does not cover any damage/s, losses, costs or expenses, direct, indirect or incidental, consequential or
special, arising out of, or related to the product.
Items purchased second hand are not covered by the two (2) year warranty, unless otherwise stipulated by local law.
During the guarantee period, the product will be either repaired or replaced at any of the authorized Polar Service Centers
regardless of the country of purchase.
Guarantee with respect to any product will be limited to countries where the product has been initially marketed.
Copyright © 2013 Polar Electro Oy, FI-90440 KEMPELE, Finland. All rights reserved. No part of this manual may be used
or reproduced in any form or by any means without prior written permission of Polar Electro Oy.
The names and logos in this user manual or in the package of this product are trademarks of Polar Electro Oy. The names
and logos marked with a ® symbol in this user manual or in the package of this product are registered trademarks of Polar
Electro Oy. Windows is a registered trademark of Microsoft Corporation and Mac OS is a registered trademark of Apple Inc.
Polar Electro Oy is a ISO 9001:2008 certified company.
This product is compliant with Directives 93/42/EEC, 1999/5/EC and 2011/65/EU. The relevant Declaration of Conformity
Compliance Statement
Canada
Polar Electro Oy has not approved any changes or modifications to this device by the user. Any changes or modifications
could void the user
Polar Electro Oy
changement ou toute modification peuvent annuler le droit
Industry Canada (IC) regulatory information
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Avis de conformité
Conformément
type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques
de brouillage radioélectrique
la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire
communication satisfaisante.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
Important Information
21
ENGLISH
Class B digital device notice
This Class B digital apparatus complies with Canadian ICES-003, RSS-Gen and RSS-210.
Cet appareil numérique de la classe B est conforme
USA
Polar Electro Oy has not approved any changes or modifications to this device by the user. Any changes or modifi cations
could void the user
FCC regulatory information
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
1.
Increase the separation between the equipment and receiver.
2.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
3.
Consult the dealer or an experienced radio/ TV technician for help.
4.
This product emits radio frequency energy, but the radiated output power of this device is far below the FCC radio
frequency exposure limits. This equipment complies with FCC RF radiation exposure limits forth for an uncontrolled
environment. Nevertheless, the device should be used in such a manner that the potential for human contact with the
antenna during normal operation is minimized.
This crossed out wheeled bin marking shows that Polar products are electronic devices and are in the
scope of Directive 2012/19/EU of the European Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and batteries and accumulators used in products are in the scope of
Directive 2006/66/EC of the European Parliament and of the Council of 6 September 2006 on batteries
and accumulators and waste batteries and accumulators. These products and batteries/accumulators
inside Polar products should thus be disposed of separately in EU countries. Polar encourages you to
minimize possible effects of waste on the environment and human health also outside the European Union
by following local waste disposal regulations and, where possible, utilize separate collection of electronic
devices for products, and battery and accumulator collection for batteries and accumulators.
This marking shows that the product is protected against electric shocks.
Disclaimer
The material in this manual is for informational purposes only. The products it describes are subject to change without
prior notice, due to the manufacturer
Polar Electro Inc. / Polar Electro Oy makes no representations or warranties with respect to this manual or with respect to
the products described herein.
Polar Electro Inc. / Polar Electro Oy shall not be liable for any damages, losses, costs or expenses, direct, indirect or
incidental, consequential or special, arising out of, or related to the use of this material or the products described herein.
This product is covered by the following patent documents: US 5486818, US6277080, US6537227, US6540686,
US20090156944, US7324841, US7076291, US6104947, US5611346, US D492999SS. Other patents pending.
Manufactured by Polar Electro Oy, Professorintie 5, FI-90440 KEMPELE.
EN 2.0 09/2013
22
Important Information
|
