PV™1 UHF
Wireless microphone system
1
INTRODUCTION
Thank you for purchasing a PEAVEY PV®-1 UHF Diversity Wireless Microphone
System. The PV-1 UHF wireless systems have user friendly features and are
available in handheld, lavalier, headset and guitar models.
•
•
Clear channel UHF operation in three available frequencies.
The proprietary compander circuitry yields a dynamic range of up to
120dB
•
Squelch control for locking out potential interference. Choice of
Transmitters:
• Bodypack with input level control.
• Handheld microphone is equipped with a neodymium cartridge
that delivers high quality audio reproduction, minimal handling
noise and enhanced feedback rejection.
•
Diversity reeiver allows for maximum reception range and dropout
protection, full LED indicators, both ¼” unbalanced and XLR balanced
outputs, and special circuitry for noiseless transmitter ON/OFF switching.
IMPORTANT SAFEGAURDS
CAUTION!
1) DO NOT attempt to make internal adjustments to the system. Please refer al servicing
to your authorized Peavey Service Center.
2) Turn the unit off if it is exposed to excessive moisture while in operation. Allow unit to dry
thoroughly, then power back up. If unit fails to power up, then refer unit to your authorized
Peavey Service Center.
WARNING! Risk of injury or death if used improperly
DURING INSTALLATION AND SET UP
To reduce the risk of shock DO NOT handle AC/DC adapter with wet hands.
To reduce the risks of fire or shock from damaged power cord always remove cord from
outlet by grasping the adapter tightly while unplugging.
To reduce the risk of fire or shock from damaged power cord always turn unit off before
3
moving it.
To reduce the risk of fire or shock DO NOT expose this equipment to moisture or dust.
To reduce the risk of fire or shock use only with specified voltage.
To reduce the risk of fire or shock DO NOT damage the power cord by placing it near a heat
source or stacking heavy items on top of it.
To prevent damage to unit DO NOT place on surface that is unstable or that can tip over.
DURING OPERATION
To reduce the risk of fire or shock DO NOT remove the chassis cover. There are no user-
serviceable parts inside. For all repairs refer unit to your authorized Peavey Service Center.
To reduce the risk of fire or shock DO NOT place water or metal items on top of unit.
To reduce the risk of fire or shock DO NOT allow metal, liquids or flammable items fall into unit.
To reduce the risk of fire or shock DO NOT touch AC outlet during thunderstorms.
To prevent injury DO NOT place heavy items on top of unit.
Clear the dust out from the inside regularly. Accumulated dust can create a fire hazard
as well as damage to the equipment.
Clear the dust out from plug and AC outlet. Again this accumulated dust can create a fire
hazard.
Make sure the AC/DC adapter is plugged in entirely. No exposed metal.
When not in use for long periods of time, turn unit off and remove the AC adapter.
UHF RECEIVER
1.
Powering the receiver
Plug the 12V AC/DC ADAPTER provided into the DC INPUT JACK on the back of the
receiver. Then plug the power supply into an AC outlet. (Note: Any DC source with 500mA
capability can also be used.) Press the POWER SWITCH (1) once to turn on the receiver. The
POWER ON LED (1) will now light and the receiver is operational.
2.
Antennas
Extend ANTENNAS (5) fully to obtain maximum range. Optimal antenna position is 45 degrees
from the receiver (at 90 degrees from each other).
4
3.
Squelch Adjustment
In normal operation, the SQUELCH CONTROL (6) should be set fully clockwise to the factory
preset RF level (Max. Sens.). However, in areas of high RF activity, the squelch (or mute, as it is
sometimes called) may need to be adjusted to compensate for the adverse conditions in a
particular location. If, with the transmitter off, the receiver’s A and/or B DIVERSITY LED
INDICTORS (3) flicker or stay on, the squelch control should be turned counterclockwise until the
A and/or B LEDs extinguish.
When the squelch is properly adjusted, the A and/or B LEDs will only light when the system
transmitter is turned on. Turning the squelch control too far counterclockwise will reduce the
range, but yield a quieter squelch (mute) function. During operation, especially at ranges greater
than 75 feet, one or the other of the A or B LEDs may extinguish briefly. This is normal – the
unit’s Diversity reception ensures that the received audio will not be interrupted. When both
LEDs extinguish, the transmitter is out of range for that given location, and the user should move
closer to the receiver to re-establish the radio link.
1. Power Switch
2. RF indictor LEDs
3. Diversity LEDs
4. AF indicator LEDs
5. Antennas
6. Squelch
7. Balanced out
8. Volume
9. Unbalanced out
10. DC Input
5
4.
Connecting the Audio Output
The UHF receiver provides both a fixed mic level BALANCED MIC AUDIO OUTPUT XLR (7) and
an adjustable line level AUX AUDIO OUTPUT ¼” JACK (9).
[Note: As when making any connection, make sure the amplifier or mixing board volume is at the
minimum level before plugging in the receiver to avoid possible sound system damage.]
INSTRUMENT CONNECTION
Insert an audio cord with a ¼” mono phone plug in the AUX AUDIO OUTPUT JACK (9) on the
rear panel of the receiver. Plug the other end of the cord into an amplifier, effects, or mixing
board, Adjust the AUX VOLUME CONTROL (8) on the UHF receiver clockwise until the volume
level is comfortable for your application. This setting is roughly equivalent to a direct instrument
cord connection.
Microphone connection (using the transmitter with either a headset or lavalier microphone or the
handheld microphone transmitter)
For Microphone use, either the BALANCED MIC AUDIO OUTPUT XLR (7) or the ¼” line level
AUX AUDIO OUTPUT (9) can be used. The XLR output is set at a nonadjustable microphone
level, similar to wired mic levels. Plug an XLR connector into the XLR output connector on the
rear of the unit and plug the other end into your amplifier or mixing board.
Make sure the volume is turned down when making connections. For your convenience, the XLR
output level is preset at the factory and is not adjustable with the receiver volume control.
The receiver is equipped with an AF PEAK LED INDICATOR (3) which lights with a strong audio
signal from the transmitter. Occasional flickering on loud inputs to the transmitter is normal. If
the LED lights continuously, decrease the volume to the transmitter or overload distortion may
result.
HANDHELD MICROPHONE
1.
2.
Unscrew the BATTERY COMPARTMENT COVER (13) and remove, exposing the BATTERY
HOLDER (14). Insert a fresh 9V ALKALINE BATTERY (15), observing the correct polarity as
marked, and screw the cover back on to the microphone. Make sure the cover is screwed on
completely. A fresh alkaline battery can last up to 10 hours in use, but in order to ensure
optimum performance, it is recommended that you replace the battery after every 7-8 hours of
use.
Turn on the microphone by sliding the OFF/STANDBY/ON SWITCH (16) to the STANDBY
position (transmitter on, audio muted) or the ON position (transmitter and audio both on). The
BATTERY INDICATOR LED will give a single quick flash, indicating usable battery strength.
In the case of a dead or low battery, the LED will either not illuminate at all or will stay on
continuously, indicating that the battery should be replaced.
6
3.
The microphone is now ready to use. The A and/or B DIVERSITY LED INDICATORS (2) on the
receiver should now be lit, indicating a received signal from the transmitter. When ready to
speak, slide the transmitter switch to the ON position. Adjust the volume of the receiver as per the
Audio Output Microphone Connection section of the above receiver instructions.
[Note: Observe care in selecting P.A. volume, transmitter location and speaker placement so that
acoustic feedback will be avoided.]
*To preserve battery life, turn the transmitter off when not in use.
BODYPACK TRANSMITTER
1.
2.
Slide open the hinged BATTERY COMPARTMENT (18) and insert (2) fresh AA ALKALINE
BATTERIES (19), observing the correct polarity. Fresh alkaline batteries can last up to 10 hours
in use, but in order to ensure optimum performance, it is recommended that the battery be
replaced after 7-8 hours of use.
The body pack is equipped with a 3.5mm LOCKING JACK (21) for connecting the audio input
selected. Connect either the INSTRUMENT CORD (22) or the HEADSET MIC (23) or LAVALIER
7
MIC CORD (24) as desired. To secure the connection, insert locking mini-XLR into the jack. To
unplug, reverse the process.
Slip the transmitter into a pocket or CLIP (28) it on to your clothes or instrument strap (if using it
as an instrument transmitter). The CLIP can be rotated 90 degree if the transmitter is to be
attached horizontally (instead of vertically) by loosening the screws holding the clip.
3.
Turn on the body pack transmitter by sliding the OFF/STANDBY/ON SWITCH (26) to the
STANBY position (transmitter on, audio mute or the ON position (transmitter and audio both on).
The BATTERY INDICATOR LED (25) will give a single quick flash, indicating usable battery
strength.
In the case of a dead or low battery, the LED either will not illuminate at all or will stay on
continuously, indicating that the battery should be replaced. To preserve battery life, turn the
transmitter off when not in use. The transmitter is now ready to use. The A and/or B
DIVERSITY LED INDICATORS (2) on the receiver should now be lit, indicating a received signal
from the transmitter.
4.
Instrument Use
Plug the ¼” phone plug from the INSTRUMENT CORD (22) into the instrument. As the cord to
the instrument also serves as the antenna, be sure to extend if fully for maximum range. Rolling
up or shortening the cord may reduce the effective operating range. When ready to play, slide
the audio OFF/STANDBY/ON SWITCH (26) to the ON position. Adjust the volume of the receiver
as per the audio Output Instrument Connections section of the above UHF receiver instructions.
(Note: Levels should be adjusted with the volume control of your instrument.)
The AF PEAK LED INDICTOR (3) on the UHF receiver will light for all loud input signals.
Occasional flickering on and off during use is normal, however if the LED stays on continuously,
turn down the instrument volume or noticeable distortion may result.
(Note: Scratchy noises can sometimes occur when some electric guitars with dirty pots or
connections are used with any wireless system. Therefore, the supplied INSTRUMENT CORD
(22) has a factory installed capacitor inside the ¼” plug. This capacitor provides first order
filtering of the RF signal from the cord into the guitar and eliminates virtually all scratchy noises.
Should your equipment still give you scratchy noises, we suggest these steps to eliminate them:
a)
b)
Make sure all guitar volume and tone pots are clean and all contacts are soldered, this is
very important.
A 47pf capacitor soldered across the hot to ground terminals of the guitar’s volume and
tone pots will provide extra filtering.
5.
Microphone Use (with either a lavalier or headset microphone)
Secure the connection from the LAVALIER (24) or HEADSET MIC CORD (23), to secure the
connection, insert locking mini-XLR into the jack. To unplug, reverse the process.
8
To use the lavalier mic, attach it at chest level or higher. Do not place it too close to the mouth –
a distance of about six inches is recommended. To use the headset mic, place it on your head
and adjust the boom so that the mic is about one inch to the side of the front of the mouth. As the
microphone cord also serves as the antenna, be sure to extend it fully. Rolling up or shortening
the cord may reduce the effective operating range – keep it as straight as possible.
When ready to speak, slide the OFF/STANDBY/ON SWITCH (26) to the ON position. Adjust the
volume of the receiver as per the Audio Output Microphone Connection section of the above UHF
receiver instructions.
[Note: Observe care in selecting P.A. volume, transmitter location and speaker placement so that
acoustic feedback will be avoided. Unidirectional mics are more resistant to feedback, but pick
up sound equally from all directions, and are prone to feedback if not used carefully.
Unidirectional mics are more resistant to feedback, but pick up sound sources best that are
directly in front of the mic. Also, mics that are farther from the sound source, such as lavaliers,
require more acoustic gain and thus more prone to feedback than close-source mics such as
handheld or headset models that are used close to the mouth.
The AF PEAK LED INDICTOR (3) on the UHF receiver will light for all loud input signals.
9
18. Battery Compartment
19. AA Batteries
23. Headset Mic
24. Lavalier Mic
21. 3.5 mm Locking Jack
22. Instrument Cord
25. Battery Indicator LED
26. On/Off/Standby Switch
28. Clip
10
SPECIFICATIONS
•
•
•
•
Frequency Response 50Hz – 15 KHz, +/- 3dB
Dynamic Range 120dB
Total Harmonic Distortion <0.6%
RF Carrier Frequency Range UHF, choice of single frequencies from 906.000 to
923.700MHz
•
•
•
Frequency Stability +/- 0.005%, Crystal controlled
Modulation FM (F3E), +/-20KHz
Operating Range Up to 250 ft. typical (depending on site conditions); up to 500+ feet
optimum line of sight
TRANSMITTERS
Audio Inputs
•
•
•
•
•
•
•
•
•
•
•
Body pack 3.5mm locking mini-jack
Body pack requires 2 AA batteries
Handheld Integrated Neodymium dynamic cartridge controls
OFF/STANDBY/ON, switch
LED Indicator Unit “ON” (single flash)
Low Battery Alert (Steady)
RF Power Out 50mW (max. allowed by FCC)
Harmonic & Spurious Emissions> - 50dB
Battery 9V Alkaline
Battery Life up to 8-10 hours
Dimensions 4.2” x 2.5” .88”
(10.7 x 6.4 x 2.2 cm)
9.5” x 1.37”
(24.1 x 3.48 cm)
•
Weight 3 oz (84g) – 7.5 oz (210g)
RECEIVER
•
•
•
•
•
•
•
•
•
Reception Mode – Diversity(Dual Antenna)
Controls – Power ON/OFF, volume control, squelch (mute) control
Connectors – DC in, ¼” unbalanced phone jack, XLR balanced output
LED Indicators – Power ON, Audio Peak, A/B Diversity
Power Requirements – DC 12-15V @ 500 mA, AC/DC adapter included
Squelch – Tone Key (32.768 KHz), external control
Unwanted Signal Rejection 60dB image and spurious
Dimensions 16” x 9.4” x 1.73”
Weight 1.15 lb (0.52 kg)
Features and specifications subject to change without notice.
EX000127
11
12
|