IN-WALL LOUDSPEAKER
SYSTEMS
MUSICA502W / MUSICA602W
OWNER'S MANUAL
1 Mitek Plaza
Winslow, IL 61089
815-367-3000
800-225-5689
21A7331
OTHER PRODUCTS FROM MUSICA
LOUDSPEAKER PLACEMENT
MUSICA In-Wall Speakers are designed to work within any interior
decorating scheme. They can be installed in virtually any location
where flush mounting is possible. To maximize their sound performance
however certain guidelines should be followed. For the best stereo
reproduction the two loudspeakers should be placed an equal distance
from your listening position and separated so that the angle between
them, at the listening position, is between 40 and 60 degrees.
MUSICA offers a wide assortment of audio components, ranging from In-
Ceiling Speakers to Cabinet Speakers to accessories. Each component
is engineered for value and performance and must meet strict quality
control standards before it becomes part of the MUSICA product Line
Listed below you will find a sampling of components available from your
authorized MUSICA dealer.
MUSICASS6
6 Position Speaker Selector
Accommodates up to 6 pair of speakers
Power Handlilng: 40W/Channel continuous RMS, 120W Peak Music
Impedance Protection Circuitry
Accommodates up to 12 gauge wire
MUSICA625C
In-Ceiling Loudspeaker
6 1/2" Polypropylene
Tweeter: 1" Soft Dome
Impedance: 8 ohms nominal
Sensitivity: 85dB
Power Handling: 55 Watts RMS/110 Watts Peak Music
Frequency Response: 48Hz-20kHz
Dim's: 9"DIA x 3 1/2"D
For best stereo imaging, we recommend that the units be placed so
that the tweeters are as close as possible to the ear level of a seated
listener.
Mounting Depth: 2 15/16" (74.6mm)
MUSICA6S
6 1/2" Two-Way Bookshelf Loudspeaker
Woofer: 6 1/2" Polypropylene
Tweeter: 3/4" Balanced Dome
Impedance: 8 ohms nominal
Sensitivity: 89dB
Power Handling: 100W RMS/200W Peak Music
Frequency Response: 55Hz-20kHz
Dim's: 12 3/4"H x 7 1/2"W x 8 1/2"D
TECHNICAL ASSISTANCE
For additional technical assistance you can visit our website at
www.MusicaAtHome.com. Otherwise, our technical service repre-
sentatives can be reached by phone: 1-800-225-5689 or by E-mail:
STEP 1
STEP 4
Using a stud finder (available at low cost at most hardware stores) or
other accurate method, locate center point between two studs and mark.
Using template provided, trace hole pattern on surface of wall. Placing a
bubble level on either the horizontal or vertical guidelines of template will
assist you in leveling the hole pattern.
Attach loudspeaker wires to speaker terminals, observing correct polarity
(positive to positive and negative to negative), and position panel and
frame assembly to hole as shown. Insert top of mounting frame into hole
at top. By moving bottom of frame upwards, you should now be able
to insert bottom of frame into hole at bottom. Be careful not to pinch
loudspeaker wires in the process. Tighten long screws. Use a level during
tightening to insure straightness of final position.
STEP 2
Using a sabre saw, keyhole saw or very sharp utility knife, cut hole in wall,
following traced pattern.
STEP 5
After speaker panel is secured tightly, test for sound.
STEP 6
When you are satisfied the speaker is operational, affix grill. As grill is
designed for a snug fit, you’ll need to position one edge into slot first, and
press or squeeze around perimeter of grill, while pushing leading edges
into grill slot.
STEP 3
Run loudspeaker wires to sound source location. There are several
methods you can use to accomplish wiring, depending on the construction
characteristics of the room or house. You can add a professional touch to
your installation by using a speaker terminal plate at the source location.
Leave sufficient amount of wire at speaker location (8 to 10 inches) to
complete connection.
|