®
36" and 48" Island Canopy Range Hood
PRODUCT MODEL NUMBERS
OVERALL DIMENSIONS
CABINET OPENING DIMENSIONS
KICU265H
KICU285H
10 7/8"
(27.6 cm)
support
structure
7 1/16"
(17.9 cm)
upper
chimney
1" (2.5 cm) min. -
Electrical: 120-volt, 60-Hz, AC-only, 15-amp.
electrical supply. Use copper wire only. A time-
delay fuse or circuit breaker and separate circuit is
recommended.
11-1/8" (23.8 cm) max.
upper chimney height
lower
chimney
24-5/8" (62.5 cm) min. -
canopy
23-5/8"
(60 cm)
lower
34-3/4" (88.3 cm) max.
overall chimney height
chimney
height
24" (61 cm) min.
bottom of canopy to
cooking surface
8’ (2.4 m) min. -
9’ (2.7 m) max.
ceiling to floor
10-1/4" (26 cm)
canopy height
23-5/8" (60 cm)
overall depth
36" hood 35-3/8" (89.9 cm) or
48" hood 47-1/4" (120 cm)
overall width
36" (91.4 cm)
base cabinet
height
VENTING REQUIREMENTS
Vertical roof venting
The vent system length should not
exceed the lengths shown in the
chart below.
3-1/4" x 10" (8.3 cm x 25 cm)
v
ent system
roof cap
3-1/4" x 10"
3-1/4" x 10”
(8.3 cm x 25 cm)
elbow
wall
cap
(8.3 cm x 25 cm)
through
the roof
Vent size
3-1/4" x 10"
Maximum length
6 ft. (1.8 m)
35 ft. (10.7 m)
(8.3 cm x 25 cm)
7" (17.8 cm) round
40 ft. (12.2 m)
50 ft. (15.2 m)
60 ft. (18.3 m)
8" (20.3 cm) round
9" (22.9 cm) round
Note: 3-1/4" x 10"
(8.3 cm x 25 cm)
rectangular vent must
be used inside chimney
cover. Round vent will
not fit inside chimney
cover.
2 ft.
(0.6 m)
To calculate the length of the system you need, add the
equivalent feet for each vent piece used in the system.
Maximum length
= 35 ft. (10.7 m)
1 — 90° elbow
8 ft. (2.4 m) straight
1 — wall cap
=
=
=
5 ft. (1.5 m)
8 ft. (2.4 m)
0 ft. (0 m)
Vent Piece
3-1/4" x 10" (8.3 cm x 25 cm) 7" (17.8 cm), 8" (20.3 cm)
Rectangular
or 9" (22.9 cm) Round
Horizontal wall venting
45° elbow
7.0 feet
2.5 feet
(0.8 cm)
Length of 3-1/4" x 10"
(8.3 cm x 25 cm)
system
3-1/4" x 10"
(2.1 m)
(8.3 cm x 25 cm)
through the wall
wall cap
= 13 ft. (4 m)
90° elbow
5.0 feet
(1.5 m)
5.0 feet
(1.5 m)
Note: Flexible vent is Not
recommended.
If it is used, each foot of flexible vent
used is equivalent to two feet (61 cm)
of straight metal vent when
calculating the vent system length.
(Example: A flexible elbow equals two
standard elbows.)
90° flat elbow
12.0 feet
(3.7 m)
Note: 3-1/4" x 10"
(8.3 cm x 25 cm)
rectangular vent must
be used inside chimney
cover. Round vent will
not fit inside chimney
cover.
transition to round
5.0 feet
(1.5 m)
wall cap
0.0 feet
(0.0 m)
Because Whirlpool Corporation policy includes a continuous commitment to improve
our products, we reserve the right to change materials and specifications without notice.
Dimensions are for planning purposes only. For complete details, see Installation
Instructions packed with product. Specifications subject to change without notice.
Ref. 4360369 Rev. C
10-15-02
|