Kambrook - Australia
Kambrook - New Zealand
Building 2, Port Air Industrial Estate
1A Hale Street
Private Bag 94411
Botany, Manukau
Botany NSW 2019
Auckland 2163
Australia
New Zealand
Customer Service Line 1300 139 798
Customer Service Fax 1800 621 337
Customer Service Line/
Spare Parts 0800 273 845
Customer Service Fax 0800 288 513
Due to continual improvement in design or otherwise, the product you
purchase may differ slightly from the illustration in this book. Issue A12
Important
Please retain your instruction
book for future use.
In the event that you need some assistance with your
Kambrook appliance, please contact our Customer Service
Department on 1300 139 798 (Australia) or 0800 273 845
(New Zealand). Alternatively, visit us on our website at
Contents
Kambrook Recommends
Safety First
p4
Your Kambrook SteamStation
Pro Steam System
p6
p7
Using Your Kambrook
Steam Station
Care and Maintenance
p13
Kambrook Recommends Safety First
IMPORTANT: Please retain your
instruction book for future use.
At Kambrook, we believe that safe performance is the first priority in any
consumer product, so that you, our valued customer can confidently
use and trust our products. We ask that any electrical appliance that
you use be operated in a sensible fashion with due care and attention
placed on the following important operating instructions.
Important Safeguards For Your Kambrook
SteamStation Pro Steam System
• Carefully read all instructions before operating
the steam station for the first time and save for
future reference.
• Do not store the steam station with water in
the water tank.Always empty the tank after
use. Ensure the iron is cool before storing.
• Remove and safely discard any packaging
material and promotional labels before using
the steam station for the first time.
• Do not touch hot surfaces.This steam station
allows the user to steam iron with a large flow
of steam. High temperatures are generated
during use which could cause burns.Always
use the handle and warn others (especially
children) of the possible dangers of burns
from steam, hot water or hot soleplate,
especially when ironing vertically.
• To eliminate a choking hazard for young
children, remove and safely discard the
protective cover fitted to the power plug of
this steam station.
• Do not place the steam station or iron near the
edge of a bench or table during operation.
Ensure that the surface is level, clean and free
of water and other substances.
• Store the steam station out of reach
of children.
• The steam station must be used and rested
on a stable surface.
• Always ensure the steam station and iron is
properly assembled before use. Follow the
instructions provided in this book.
• When placing the iron on its heel, ensure
that the surface on which the heel is
placed is stable.
• Do not operate the steam station on a sink
drain board.
• The steam station is not to be used if the iron
and steam station has been dropped, if there
are visible signs of damage or if it is leaking
• Do not use outdoors or in bathrooms.
• Do not leave the steam station unattended
when in use.
• Do not use if there is visible leaking from the
cable and steam pipe. In case of leaking,
it must be replaced by a special cord or
assembly available from the manufacture
or its service agent.
• Always turn the variable temperature control
to minimum, switch off at the power outlet, and
then unplug the steam station when not in use.
• Allow the steam iron and iron rest to cool
completely before storing the steam iron
and steam station.
• Always test the iron on a small discreet part of
the fabric to be iron to ensure the temperature
is not set too high.
• Always place the steam iron on the iron
rest when storing. Do not leave the steam
station unattended while connected or
on an ironing board.
•
To prevent damage to the iron and steam station
do not use alkaline cleaning agents when
cleaning, use a soft cloth and mild detergent.
4
• The iron incorporates a thermal safety fuse to
protect the iron from over heating. However
the iron and steam station should not be left
unattended while it is connected to the
power outlet. Special care should always
be taken when there are children in the
home/vicinity of the steam station.
• If the steam iron is set to a low temperature on
the temperature control (i.e. synthetic or silk)
there may be leakage from the soleplate.This
is due to the steam station temperature not
being high enough to vaporize the water and
create steam.Therefore, ensure that the steam
control is always set to correspond with the
setting on the temperature control as seen in
Table A (see section ‘Setting the Temperature’)
• Do not touch the iron rest when in use
and just after use. Ensure the iron rest is
cool before attempting to touch or
prior to storing the steam station.
• Do not allow the cord to touch hot surfaces.
• Keep the steam station clean. Follow the
• Never use the vertical steam shot while
clothes are on the body or direct the steam
towards people.
cleaning instructions provided in this book.
Important Safeguards For All
Electrical Appliances
• Fully unwind the power cord before use.
• This appliance is for household use only.
Do not use this appliance for anything
other than its intended use. Do not use
in moving vehicles or boats. Do not use
outdoors. Misuse may cause injury.
• Connect only to 230V or 240V power outlet.
• Do not let the power cord hang over the
edge of a bench or table, touch hot
surfaces or become knotted.
• The installation of a residual current device
(safety switch) is recommended to provide
additional safety protection when using
electrical appliances. It is advisable that a
safety switch with a rated residual operating
current not exceeding 30mA be installed in
the electrical circuit supplying the appliance.
See your electrician for professional advice.
• To protect against electric shock, do not
immerse the power cord, power plug or
appliance in water or any other liquid or
allow moisture to come in contact with
the part, unless it is recommended in the
cleaning instructions.
• The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
• Always turn the appliance to the OFF position,
switch off at the power outlet and unplug at
the power outlet when the appliance is not
in use.
• Before cleaning, always turn the appliance to
the OFF position, switch off at the power outlet,
unplug at the power outlet and remove the
power cord, if detachable, from the appliance
and allow all parts to cool.
• Children should be supervised to ensure
that they do not play with the appliance.
• It is recommended to regularly inspect the
appliance.To avoid a hazard, do not use
the appliance if power cord, power plug or
appliance becomes damaged in any way.
Return the entire appliance to the nearest
authorized Kambrook service centre for
examination and / or repair.
• Do not place this appliance on or near a heat
source, such as hot plate, oven or heaters
• Position the appliance at a minimum
distance of 20cm away from walls, curtains
and other heat or steam sensitive materials
and provide adequate space above and
on all sides for air circulation.
• Any maintenance other than cleaning
should be performed at an authorised
Kambrook Service Centre.
5
Your Kambrook SteamStation Pro Steam System
1. 2400 watt steam station with
non-stick soleplate for easy
gliding over all fabric types
2. Steam control button with
continuous steam lock
5. Removable easy-fill 800ml water
tank with water level indicator
6. Thermostat control for selection
of fabric temperatures from
MIN (silk) to MAX (linen)
mechanism – locks on for
continuous steam ironing
or simply press and hold to
activate steam as required
7. Power Indicator light illuminates
when the iron is plugged into a
power outlet and switched on
(not shown)
3. Iron thermostat light
8. Variable steam control dial
4. Iron rest for placing hot iron
during ironing and to store iron
when not in use
9. Base with iron connection cord
and power cord
10. Removable anti-scale filter
cartridge (located in water tank)
M
S
S
M
Y
N
T
A
H
N
E
T
X
I
C
O
L
C
O
T
S
T
T
E
A
O
N
L
I
N
E
N
6
Operating Your Kambrook Steam Station
Before First Use
IMPORTANT: When
Remove any sticker or protective
cover from the soleplate.
unpacking the steam
station, check to see you
have received all the
items before discarding
the packaging.
When operating the steam station
for the first time, iron on an old piece
of fabric to ensure that the soleplate
and water tank are completely clean.
Clean the Anti-Scale Filter Cartridge
following the directions listed in
this instruction manual under
NOTE: To avoid an electrical
circuit overload, it is
recommended that no other
appliances are plugged into
the same circuit as your steam
station when it is in use.
‘Care and Maintenance’
.
When the steam station is used for the
first time, some vapour may emit from
the iron.After a short while however,
this will cease.The vapour is due to
the initial heating of the materials
used in the iron. It is safe and will not
harm the performance of the iron.
7
Operating Your Kambrook Steam Station continued
Work through to the fabrics
Setting the Temperature
requiring higher temperatures.
Before commencing ironing, first sort
Both the Temperature Control
the items to be ironed according to
and most items of laundry have
the International Textile Care
markings corresponding with
this code (see Table A).
Labelling Code or by the type of
fabric. Iron fabrics that require the
lowest temperatures first.
Table A
on label means: “This article cannot be ironed”
[e.g. chlorofibre, acrylic, elastodiene]
NOTE:
Label Code
Kind of Textile
Temperature Control
Variable Steam Control
[see garment instruction]
[advised position]
MIN
synthetic
modacry
polypropylene
polyurethane
acetate
DRY
triacetate
matalized
cupro
plyamide [nylon]
polyester
modal
viscose [rayon]
silk
MIN STEAM
MAX STEAM
wool
cotton
LINEN
MAX
linen
8
To Operate Your Kambrook
Steam Station
NOTE: Always place your iron
with the non-stick soleplate
sitting correctly on the Iron Rest
provided. The Iron Rest is fitted
with non-slip inserts and has
been designed to withstand
high temperatures.
•
Remove the water tank from the
steam station base by grasping
the handle at the front of the
water tank and pulling forward
until the tank clears the base.
Pull upwards on the anti-scale
filter cartridge fitted to the top
of the water tank to remove.
•
Fill the water tank with normal tap
water; do not exceed the MAX
water level marking on the tank.
wARNINg: The soleplate
of the iron must be
placed on the Iron
Rest correctly to avoid
damaging the Steam
Station Base. Do not sit
the soleplate too forward
on the Iron Rest so it sits
over the edge of the Iron
Rest; ensure the soleplate
is sitting correctly on the
non-slip inserts only.
NOTE: Your steam station
is designed to work with
untreated tap water.
•
•
•
Fit the anti-scale filter cartridge
back into place and slide the
water tank into the base of the
steam station making sure that
it is properly fitted.
Plug the power cord into a 230V
or 240V power point and switch
on.The Power Indicator Light at
the back of the steam station
base will illuminate.
Turn the Thermostat Control
located on the iron to the desired
temperature or in accordance
with the Textile Labelling Code;
wait for the non-stick soleplate
to heat up.When it reaches the
correct temperature, the Iron
Thermostat Light will go out,
then cycle on and off as the
thermostat operates to maintain
the temperature.
IMPORTANT: Do not
use tumble dryer
condensate, scented
water softened water
refrigerator condensate,
battery water, air
conditioner condensate,
distilled water or
rainwater as they contain
organic waste or mineral
components that are
concentrated by heat
and cause spitting,
brown staining
or premature aging of
your appliance.
9
Operating Your Kambrook Steam Station continued
•
Alternatively, press the Steam
Control Button down and slide
back slightly on the Continuous
Steam Lock mechanism. Steam
will emit continuously while
the Continuous Steam Lock is
activated.To release, slide the lock
mechanism forward until the Steam
Control Button rises upwards. (Fig 1).
Continuous Steam Ironing
wARNINg: To extend
the life of the pump on
your Steam Station, do
not operate the steam
function for more than
10 minutes continuously.
•
Before first use, it is recommended
to allow the iron to steam for
about one minute (the time that
it takes the pump to start and
the first bursts of steam to emit
from the iron) before placing the
iron on your garment. Once the
pump has started, press the Steam
Control Button a few times before
commencing ironing.
Fig. 1
IMPORTANT: When the
iron is being used for
the first time, the Steam
Control Button must be
held down for about
1 minute until the
NOTE: Do not press the Steam
Control Button or slide the
Continuous Steam Lock while
the water tank is empty. Do not
press the Steam Control Button
or slide the Continuous Steam
Lock when the iron is sitting on
the Iron Rest.
pump starts and
steam is produced.
•
Wait until the Iron Thermostat
Light goes out three times to
ensure temperature is reached.
Press on the Steam Control
IMPORTANT: Before
steam ironing, you should
ensure that the garment
can be steam ironed
according to its Textile
Care Labelling.
Button. Steam will emit as long as
you hold down the Steam Control
Button at the front of the button
and stop when released.
NOTE: If you want to use steam,
the Thermostat Control dial on
the iron must be set to the area
marked STEAM.
•
To control the flow of steam, turn
the Variable Steam Control Dial
at the back of the steam station
base until the desired steam
pressure is reached. (Fig 2).
10
•
•
Hang the garment from a hanger
and stretch the fabric slightly with
one hand checking that there
is nothing behind the fabric that
can be damaged by the steam.
Hold the iron close to, but not
touching the fabric. Hold the iron
well away from delicate fabrics
and use a low steam setting.
M
S
M
A
N
X
Fig. 2
wARNINg: Steam will
not be produced for
steam ironing if the
temperature on the
Thermostat Control is
not set to the area
marked STEAM and the
Steam Control Button is
not pressed.
NOTE: As the steam pump is
getting up to temperature,
it may emit some noise. This
will grow quieter as the steam
comes through. If the water tank
runs out of water, the pump will
start to get noisy.
wARNINg: As the steam
produced is very hot,
never iron or steam iron a
garment while it is being
worn; always hang the
garment on a hanger.
Steam Boost On Demand
•
Steam can be used to help
remove stubborn creases while
ironing.To activate Steam Boost,
ensure the Thermostat Control
is set to an appropriate setting
to produce steam, then press
down at the front of the Steam
Control Button and hold as
long as required.
•
With the iron held vertically
and tilted slightly forwards,
press intermittently on the
Steam Control Button while
moving it from the top of the
garment to the bottom.
Steam will emit as long the Steam
Control Button is pressed down
and will stop when released.
Vertical Steam Ironing
NOTE: If using starch, spray it
onto the opposite side of the
garment to the side you are
steam ironing.
•
To vertical steam iron, ensure
there is water in the water tank
and turn the Thermostat Control
on the iron to the MAX position.
Set the Variable Steam Control
Dial to the desired setting for the
amount of steam required.
11
Operating Your Kambrook Steam Station continued
wARNINg: Do not press
the Steam Control Button
when the Thermostat
Control Dial is not set to a
temperature marked for
STEAM, as doing so may
cause water to drip from
the soleplate.
Dry Ironing
•
To dry iron, set the Thermostat
Control to the appropriate setting
and wait until the non-stick
soleplate heats up. Begin ironing.
Do not press down on the Steam
Control Button whilst dry ironing.
NOTE: Do not iron over metal
parts such as fastenings and
buttons.
wARNINg: The steam
station should not be left
switched on deliberately
while unattended. The
steam station should
always be switched
off at the power outlet
and unplugged when
not in use or being left
unattended.
12
Care and Maintenance
After Each Use
Anti-Scale Filter Cartridge
•
Set the Variable Steam Control
Dial on the base of the steam
station to the MIN position and
turn the Temperature Control dial
on the iron to MIN.
•
To reduce scale build-up
and keep your steam station
performing at its best, the Anti-
Scale Filter Cartridge should be
cleaned regularly. How often
depends on the hardness of
your water, and how much
you use the iron.
•
•
Switch the power off at the power
outlet and disconnect the power
cord from the power outlet.
Detach the Water Tank from the
base and remove the Anti-Scale
Filter Cartridge. Invert the water
tank (over a sink or bucket) to
empty the remaining water.
•
•
•
•
To clean the Anti-Scale Filter
Cartridge, remove from the
water tank.
Dip the base of the cartridge in a
bowl of hot water and let soak for
up to an hour.
Carefully remove from the water
and shake cartridge to remove
excess water.
Fit the Anti-Scale Filter Cartridge
back into the water tank ready
for next use.
Once the water tank is empty,
replace the filter and place the
water tank back into the base.
•
Rest the iron on the soleplate on
the Iron Rest of the steam station
and allow to cool before moving
or storing.
NOTE: It is not recommended
to leave water in the water tank
over long periods of time to
avoid mould. Empty the water
tank after each use.
13
Storing Your Steam Station
Cleaning the Soleplate and
Exterior
•
Set the Variable Steam Control
to the MIN position and turn the
Temperature Control on the iron
to MIN.
•
Ensure that the steam station
is disconnected from the
power outlet.
•
•
Switch the power off at the power
outlet and disconnect the power
cord from the power outlet.
Rest the iron on the soleplate on
the Iron Rest of the steam station
and allow to cool completely
before storing.
•
To remove residue which may
have built up from certain
fabric finishes, clean the non-
stick soleplate with a rough
cloth that has been soaked in a
vinegar and water solution. Dry
thoroughly with a soft cloth.
•
•
Empty the tank and replace in
the steam station once empty
for storing.
Store the steam station in a safe
place where it can not fall or
be damaged.
NOTE: You may also use a
commercial sole plate cleaner
found at most supermarkets to
remove residue.
•
•
Do not set anything on top of
your steam station.
•
•
To clean the steam holes, simply
use a damp cloth to wipe away
build up of lint or starch from
inside the steam holes.
Wipe the outer housing with a
soft, damp clean cloth and polish
with a dry cloth.
It is not recommended to leave
your steam station resting on
your ironing board when not in
use as the ironing board can
be knocked causing the steam
station to fall and be damaged.
NOTE: Never use abrasives or
scouring pads to clean the
soleplate. Avoid hard contact
with metal objects. Do not scratch
or damage the surface of the
soleplate. Do not use harsh or
abrasive cleaners as they may
damage the surface of the iron.
Never immerse the iron in water
or any other liquid.
14
Notes
15
|