Hotpoint Ventilation Hood LI2JDA User Manual

Instructions for Installation and Use  
Electric Hood  
 
6
5
1
4
2
3
f
2
1
j
i
g
g
h
2
3
 
G
=
X
=
17a  
X
F
17a  
H
H
11  
11  
17b  
G
12  
17b  
4-13  
8
1
4-13  
8
18  
15  
3
16  
6
5
2
7
B
6
5
9
5
6
10  
9
10  
14  
17  
14  
4
 
Consult the designs in the front pages referenced in the text by  
alphabet letters. Closely follow the instructions set out in this  
manual.Allresponsibility, foranyeventualinconveniences,damages  
or fires caused by not complying with the instructions in this manual,  
is declined.  
Thecookerhoodmustbeplacedataminimumdistanceof50cmfrom  
the cooking plane for electric cookers and 65cm for gas or mixed  
cookers.  
Iftheapplianceisinstalledaboveagascookingdevicewithinstallation  
instructions specifying a greater clearance, you must take this into  
account.  
Do not tile, grout or silicone this appliance to the wall. Surface  
mounting only.  
The hood is equipped with a top air outlet B for discharge of fumes to  
the outside (Ducting version – exhaust pipe and pipe fixing clamps  
not provided).  
Shoulditnotbepossibletodischargecookingfumesandvapourtothe  
outside, thehoodcanbeusedinthefilter version, fittinganactivated  
carbon filter and the deflector F  
on the support (bracket) G, fumes and vapours are recycled through  
the top grille H by means of an exhaust pipe connected to the top air  
outlet B and the connection ring mounted on the deflector F (exhaust  
pipe and pipe fixing clamps not provided).  
telescopic chimney flue.  
Assembling the deflector (only when a deflector composed of  
3 parts is supplied – the deflector should be only for the filter  
version):  
The three parts should be fixed with 2 screws, the deflector extension  
is adjustable and should correspond to the width of the chimney flue  
support, to which it is then fixed.  
1. Usingapencil, drawalineonthewall, extendinguptotheceiling,  
to mark the centre. This will facilitate installation.  
2. Rest the drilling template against the wall: the vertical centre line  
printed on the drilling template must correspond to the centre line  
drawn on the wall, and the bottom edge of the drilling template  
must correspond to the bottom edge of the hood: bear in mind  
that, when installation is complete, the underside of the hood  
mustbeatleast50cmabovethecookertopinthecaseofelectric  
cookers, and at least 65 cm above the cooker top in the case of  
gas or mixed cookers.  
3. Rest the support bracket on the drilling template so that it  
coincides with the dotted rectangle, mark the two outer holes and  
drill them, remove the drilling template, insert 2 wall plugs and fix  
the hood support bracket into place using two 5x45mm screws.  
4. Hang the hood on the bracket.  
5. Adjust the distance of the hood from the wall.  
6. Adjust the horizontal position of the hood.  
7. Using a pencil mark the cooker hood permanent drill hole inside  
the suction group (two drill holes are necessary for fastening).  
8. Remove the hood from the bracket.  
9. Drill at the point marked (Ø8mm - see operation 7).  
10. Insert 2 wall plugs.  
11. Rest the chimney support bracket „G“ against the wall, touching  
the ceiling. Use the support bracket as a drilling template (the  
smallslotformedonthesupportmustcoincidewiththelinedrawn  
onthewallasaboveoperation1)andmark2holeswithapencil,  
drill the holes (Ø8mm), insert 2 wall plugs.  
The models with no suction motor only operate in ducting mode, and  
must be connected to an external suction device (not supplied).  
Installation - Fig. 4  
Preliminary information for installation of the hood:  
Disconnectthehoodduringelectricalconnection,byturningthehome  
mains switch off. Expansion wall plugs are provided to secure the  
hood to most types of walls/ceilings. However, a qualified technician  
must verify suitability of the materials in accordance with the type of  
wall/ceiling. Thewall/ceilingmustbestrongenoughtotaketheweight  
of the hood.  
12. Fix the chimney support bracket to the wall using two 5x45mm  
screws.  
13. Hook the hood onto the bottom bracket.  
Do not tile, grout or silicone this appliance to the wall. Surface  
mounting only.  
Donotfixchimneyfluetofurnitureorflyovershelvesunlessthe  
chimney flue can be easily removed, in case maintenance is  
ever required.  
Where foreseen remove the grease collecting panels.  
Remove the grease filter/s  
Do not tile, grout or silicone this appliance to the wall. Surface  
mounting only. Do not fix chimney flue to furniture or fly over shelves  
unless the chimney flue can be easily removed, in case maintenance  
is ever required.  
14. Fix the hood into its final position on the wall (ABSOLUTELY  
ESSENTIAL).  
15. Connect a pipe (pipe and pipe clamps not provided, to be  
purchased separately) for discharge of fumes to the connection  
ring located over the suction motor unit.  
If the hood is to be used in ducting version, the other end of the  
pipe must be connected to a device expelling the fumes to the  
outside. If the hood is to be used in filter version, then fix the  
deflector F to the chimney support bracket G and connect the  
other extremity of the pipe to the connection ring placed on the  
deflector F.  
16. Make the electrical connections.  
17. Apply the chimney stacks and fasten them at the top to the  
chimney support „G“ (17b) using 2 screws (17a).  
18. Slide the bottom section of the chimney down until it completely  
covers the suction unit and slots into the housing provided on top  
of the hood.  
Replace the grease filter/s (and where foreseen the grease collecting  
panels) and check that the hood is operating correctly.  
X
=
=
G
F
F
=
=
X
X
G
Electrical connection  
The electrical tension must correspond to the tension noted on the  
label placed inside the cooker hood. Connect the electrical plug,  
where provided, to the an easily accessible outlet in conformity with  
local standards in force.  
H
Where an electrical plug is not provided (for direct connection to  
electrical network) place a standards approved bipolar switch with an  
aperturedistanceofnotlessthan3mm(accessible)fromthecontacts.  
Assembling the chimney flue support/bracket (3 parts):  
The three parts should be fixed with 4 screws, the support extension  
6
is adjustable and should correspond to the internal width of the  
 
the chimney to the cooker hood (Fig. 2).  
Insertthepad(i)ofactivatedcarbonintotheframe(h)andfitthewhole  
back into its housing (j).  
Description of the hood - Fig. 1  
1 Control panel  
2 Grease filter  
3 Lamp  
4 Vapour screen  
5 Telescopic chimney  
6 Air outlet (used for filter version only)  
Replacing lamps - Fig. 3  
Warning!  
Prior to touching the light bulbs ensure they are cooled down.  
1. Extract the guard by levering it off with a small screwdriver or  
similar tool.  
2. Replace the damaged light bulb.  
Onlyusehalogenbulbsof20Wmax(G4),makingsureyoudonot  
touch them with your hands.  
Operation  
3. Close the lamp cover (it will snap shut).  
If the lights do not work, make sure that the lamps are fitted  
properly into their housings before you call for technical  
assistance.  
1
2
3
4
1. on/off light switch  
Caution  
2. key OFF/ON suction and power selection of suction 1  
2. + 3. power selection of suction 2  
2. + 3. + 4.power selection of suction 3  
The appliance is not intended for use by young children or infirm  
persons without supervision.  
Young children should be supervised to ensure that they do not play  
with the appliance.  
WARNING-Ensurethattheapplianceisswitchedoffbeforereplacing  
the lamp to avoid the possibility of electric shock.  
Use the high suction speed in cases of concentrated kitchen vapours.  
It is recommended that the cooker hood suction is switched on for 5  
minutes prior to cooking and to leave in operation during cooking and  
for another 15 minutes approximately after terminating cooking.  
Do not use the cooker hood where the grill is not correctly fixed! The  
suctioned air must not be conveyed in the same channel used for  
fumes discharged by appliances powered by other than electricity.  
The environment must always be adequately aerated when the  
cooker hood and other appliances powered by other than electricity  
are used at the same time. Flambé cooking with a cooker hood is  
prohibited. The use of a free flame is damaging to the filters and may  
cause fire accidents, therefore free flame cooking must be avoided.  
Frying of foods must be kept under close control in order to avoid  
overheatedoilcatchingfire.Carryoutfumesdischarginginaccordance  
with the regulations in force by local laws for safety and technical  
restrictions.  
If the hood fails to operate correctly, briefly disconnect it from the  
mainspowersupplyforalmost5sec.bypullingouttheplug.Thenplug  
itinagainandtryoncemorebeforecontactingtheTechnicalAssistance  
Service.  
Maintenance  
Prior to any maintenance operation ensure that the cooker hood is  
disconnected from the power supply.  
Cleaning the hood  
Thecookerhoodshouldbecleanedregularlyinternallyandexternally.  
For cleaning use a cloth moistened with denatured alcohol or neutral  
liquid detergents. Avoid abrasive detergents.  
Warning:  
Failure to carry out the basic standards of the cleaning of the cooker  
hood and replacement of the filters may cause fire risks.  
Therefore we recommend oserving these instructions.  
Grease filter  
Thismustbecleanedonceamonthusingnonaggressivedetergents,  
either by hand or in the dish-washer, which must be set to a low  
temperature and a short cycle.  
When washed in a dish-washer, the grease filter may discolour  
slightly, but this does not affect its filtering capacity.  
Toremovethegreasefilter, pullthespringreleasehandle(f) -(Fig. 1).  
Charcoal filter (filter version only)  
It absorbs unpleasant odours caused by cooking.  
The charcoal filter can be washed once every two months using hot  
waterandasuitabledetergent,orinadish-washerat6C(ifthedish-  
washer is used, select the full cycle function and leave dishes out).  
Eliminate excess water without damaging the filter, then remove the  
mattress located inside the plastic frame and put it in the oven for 10  
minutes at 100° C to dry completely. Replace the mattress every 3  
years and when the cloth is damaged.  
7
Remove the filter holder frame by turning the knobs (g) 90° that affix  
 
After Sales Service  
"No company is better positioned to offer an after sales service on a  
Hotpoint appliance than us - the manufacturer"  
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive  
parts and labour guarantee for the first 12 months. In addition to this you also have the advantage of  
free replacement parts for the first 5 years when fitted by a Hotpoint  
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales  
service options:  
Repair Service and Information Help Desk  
UK: 08709 066066  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the Model number and the Serial number of your appliance  
Available 364 days a year with a fast, effective and value for money service. We have the largest  
white goods repair service in the UK with over 1000 of our own fully trained engineers. All repairs  
include a parts and labour guarantee for 12 months from the date of the repair.  
If you require any information or have any questions about your appliance, our operators are on hand  
with help and advice.  
All this ensures that you will receive the best available after sales service possible.  
Extended Warranties  
UK: 08709 088 088  
Republic of Ireland: 1850 502 200  
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service  
cover plans to give you total peace of mind.  
Repair Protection Plan  
-
FREE service repairs for a single Hotpoint appliance during the  
period of cover.  
FREE service repairs for all your Hotpoint appliances less than  
Kitchen Cover  
-
8 years old.  
Genuine Parts and Accessories  
UK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
A wide range of genuine parts and accessories are available from our hotline or through our website.  
Genuine parts and accessories, extended warranties and service repairs are all  
available on our web-site at:  
7
GB910  
 
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have complete  
confidence in both the appliances and services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number:  
Serial number:  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
Republic of Ireland: (01) 842 6836  
Merloni Elettrodomestici UK Ltd., Morley Way , Peterborough, PE2 9JB  
LI2JDA Ed. 11/04  
 

Grizzly Staple Gun G6772 User Manual
Hamilton Beach Coffeemaker 840142000 User Manual
Hasbro Portable Speaker 75024 User Manual
Heath Zenith Door 598 1000 07 User Manual
Hotpoint Clothes Dryer TVM572 User Manual
Hotpoint Dishwasher HDA3500NBB User Manual
HP Hewlett Packard Personal Computer 43361 User Manual
HP Hewlett Packard Ventilation Hood 493A User Manual
IBM Computer Monitor T86A User Manual
Impex Fitness Equipment MWB 214 User Manual