Harbor Freight Tools Router 68341 User Manual

2 HP Fixed Base Router  
68341 Router  
Read this material before using this product.  
Failure to do so can result in serious injury.  
Save tHiS manual.  
When unpacking, make sure that the product is intact and undamaged.  
If any parts are missing or broken, please call 1-800-444-3353 as soon as possible.  
©
®
Copyright 2011 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape  
or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing  
improvements, actual product may differ slightly from the product described herein. Tools required for assembly and service may not be included.  
 
3. Personal safety  
d. Store idle power tools out of the reach of  
children and do not allow persons unfamiliar  
with the power tool or these instructions  
to operate the power tool. Power tools are  
dangerous in the hands of untrained users.  
a. Stay alert, watch what you are doing  
and use common sense when operating  
a power tool. Do not use a power  
tool while you are tired or under the  
influence of drugs, alcohol or medication.  
A moment of inattention while operating power  
tools may result in serious personal injury.  
e. maintain power tools. Check for misalignment  
or binding of moving parts, breakage of parts  
and any other condition that may affect the  
power tool’s operation. if damaged, have the  
power tool repaired before use. Many accidents  
are caused by poorly maintained power tools.  
b. use personal protective equipment.  
always wear eye protection. Safety equipment  
such as dust mask, non-skid safety shoes, hard  
hat, or hearing protection used for appropriate  
conditions will reduce personal injuries.  
f. Keep cutting tools sharp and clean. Properly  
maintained cutting tools with sharp cutting edges  
are less likely to bind and are easier to control.  
c. Prevent unintentional starting. ensure the  
switch is in the off-position before connecting  
to power source and/or battery pack, picking  
up or carrying the tool. Carrying power tools  
with your finger on the switch or energizing power  
tools that have the switch on invites accidents.  
g. use the power tool, accessories and tool bits  
etc. in accordance with these instructions,  
taking into account the working conditions  
and the work to be performed. Use of the  
power tool for operations different from those  
intended could result in a hazardous situation.  
d. Remove any adjusting key or wrench  
before turning the power tool on.  
5. Service  
A wrench or a key left attached to a rotating part  
of the power tool may result in personal injury.  
Have your power tool serviced by a  
qualified repair person using only identical  
replacement parts. This will ensure that the  
safety of the power tool is maintained.  
e. Do not overreach. Keep proper footing and  
balance at all times. This enables better control  
of the power tool in unexpected situations.  
f. Dress properly. Do not wear loose clothing or  
jewelry. Keep your hair, clothing and gloves  
away from moving parts. Loose clothes, jewelry  
or long hair can be caught in moving parts.  
Router Safety Warnings  
1. Hold power tool by insulated gripping surfaces  
when performing an operation where cutting  
tool may contact hidden wiring or its own cord.  
Contact with a ″live″ wire will make exposed metal  
parts of the tool ″live″ and shock the operator.  
g. if devices are provided for the connection of  
dust extraction and collection facilities, ensure  
these are connected and properly used. Use of  
these devices can reduce dust-related hazards.  
2. use clamps or another practical way to secure  
and support the work piece to a stable platform.  
Holding the work by hand or against your body  
leaves it unstable and may lead to loss of control.  
h. Only use safety equipment that has been  
approved by an appropriate standards  
agency. Unapproved safety equipment  
may not provide adequate protection.  
Eye protection must be ANSI-approved and  
breathing protection must be NIOSH-approved  
for the specific hazards in the work area.  
3. Use only accessories rated at least equal  
to maximum speed marked on Router.  
4. Only use router bits with a shank diameter  
equal to the size of the tool’s collet. The collet  
size is adjustable for 1/4", 3/8" or 1/2".  
4. Power tool use and care  
a. Do not force the power tool. use the correct  
power tool for your application. The correct  
power tool will do the job better and safer  
at the rate for which it was designed.  
5. Make sure the collet nut is securely tightened before  
use to prevent the router bit from slipping during use.  
6. Do not use with base removed.  
7. Hold router with both hands.  
b. Do not use the power tool if the  
switch does not turn it on and off.  
Any power tool that cannot be controlled with  
the switch is dangerous and must be repaired.  
8. Keep hands away from the cutting area. Do  
not place hands beneath the workpiece for  
any reason. Keep the base of the router in firm  
contact with the workpiece while cutting.  
c. Disconnect the plug from the power source  
and/or the battery pack from the power tool  
before making any adjustments, changing  
accessories, or storing power tools.  
9. Keep Handles dry, clean, and free of oil or grease.  
This will permit better control of the tool.  
Such preventive safety measures reduce the  
risk of starting the power tool accidentally.  
10. Do not use damaged bits.  
SKU 68341  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
11. Do not lay the Router down until it has  
stopped rotating completely.  
pacemaker interference or pacemaker failure. In  
addition, people with pacemakers should:  
• Avoid operating alone.  
• Do not use with power switch locked on.  
• Properly maintain and inspect to avoid  
electrical shock.  
• Any power cord must be properly  
grounded. Ground Fault Circuit Interrupter  
(GFCI) should also be implemented –  
it prevents sustained electrical shock.  
12. Hold the Router firmly when starting, as  
startup rotation creates significant torque.  
13. Hold the Router firmly while cutting. The action of the  
bit against the workpiece can cause it to “kick out”,  
jumping rapidly away from the workpiece. This can  
be caused by an improper type of bit, or a dull bit.  
14. Do not handle the Router bit immediately  
after cutting. It may be very hot,  
27. WARNING: Some dust created by power sanding,  
sawing, grinding, drilling, and other construction  
activities, contains chemicals known [to the State  
of California] to cause cancer, birth defects or  
other reproductive harm. Some examples of  
these chemicals are:  
potentially causing burns or injury.  
15. Avoid overloading the tool. If the speed  
drops abnormally, decrease the pressure on  
the bit immediately. Do not apply excessive  
pressure to the router while cutting.  
• Lead from lead-based paints  
• Crystalline silica from bricks and cement or  
other masonry products  
• Arsenic and chromium from  
chemically treated lumber  
16. Always use sharpened bits. If the bit stops  
abruptly, or the bit becomes blocked, remove  
the Router from the workpiece and shut it off.  
Your risk from these exposures varies, depending on  
how often you do this type of work. To reduce your  
exposure to these chemicals: work in a well ventilated  
area, and work with approved safety equipment, such  
as those dust masks that are specially designed to  
filter out microscopic particles.  
17. Do not start the Router while the bit is in  
contact with the workpiece. Allow the tool  
to reach its normal operating speed before  
applying the bit to the workpiece.  
18. Use caution when setting the Locking Trigger  
Switch. Be aware that the router will continue to  
operate while the locking mechanism is engaged.  
Do not lay the router down or hand it to another  
person while the locking mechanism is engaged.  
(California Health & Safety Code § 25249.5, et seq.)  
28. WARNING: Handling the cord on this product will  
expose you to lead, a chemical known to the State of  
California to cause cancer, and birth defects or other  
reproductive harm. Wash hands after handling.  
(California Health & Safety Code § 25249.5, et seq.)  
19. Before Routing, run the tool for about 10 seconds  
to ensure that all moving parts are running  
smoothly and there are no loose parts, rattles,  
or sparking that would indicate damage.  
29. The warnings, precautions, and instructions  
discussed in this instruction manual cannot  
cover all possible conditions and situations  
that may occur. It must be understood by the  
operator that common sense and caution are  
factors which cannot be built into this product,  
but must be supplied by the operator.  
20. Maintain labels and nameplates on the tool.  
These carry important safety information. If  
unreadable or missing, contact Harbor  
Freight Tools for a replacement.  
21. Avoid unintentional starting. Prepare to  
begin work before turning on the tool.  
vibration Safety  
22. When using a handheld power tool,  
maintain a firm grip on the tool with both  
hands to resist starting torque.  
This tool vibrates during use.  
Repeated or long-term exposure to vibration may  
cause temporary or permanent physical injury,  
particularly to the hands, arms and shoulders.  
To reduce the risk of vibration-related injury:  
23. Do not leave the tool unattended when it is plugged  
into an electrical outlet. Turn off the tool, and  
unplug it from its electrical outlet before leaving.  
1. Anyone using vibrating tools regularly or for an  
extended period should first be examined by a  
doctor and then have regular medical check-ups to  
ensure medical problems are not being caused or  
worsened from use. Pregnant women or people who  
have impaired blood circulation to the hand, past  
hand injuries, nervous system disorders, diabetes,  
or Raynaud’s Disease should not use this tool.  
If you feel any symptoms related to vibration (such  
as tingling, numbness, and white or blue fingers),  
seek medical advice as soon as possible.  
24. Only use accessories rated to the speed  
of the tool. Other accessories may fly  
apart, causing severe personal injury.  
25. This product is not a toy.  
Keep it out of reach of children.  
26. People with pacemakers should consult their  
physician(s) before use. Electromagnetic fields in  
close proximity to heart pacemaker could cause  
Page 4  
For technical questions, please call 1-800-444-3353.  
SKU 68341  
 
2. Do not smoke during use. Nicotine reduces  
the blood supply to the hands and fingers,  
increasing the risk of vibration-related injury.  
down, grounding provides a low resistance path to  
carry electricity away from the user, reducing the risk  
of electric shock. (See 3-Prong Plug and Outlet.)  
3. Wear suitable gloves to reduce the  
vibration effects on the user.  
2. The grounding prong in the plug is connected through  
the green wire inside the cord to the grounding  
system in the tool. The green wire in the cord must  
be the only wire connected to the tool’s grounding  
system and must never be attached to an electrically  
“live” terminal. (See 3-Prong Plug and Outlet.)  
4. Use tools with the lowest vibration  
when there is a choice.  
5. Include vibration-free periods each day of work.  
3. The tool must be plugged into an appropriate outlet,  
properly installed and grounded in accordance with  
all codes and ordinances. The plug and outlet should  
look like those in the preceding illustration.  
6. Grip tool as lightly as possible (while still keeping  
safe control of it). Let the tool do the work.  
7. To reduce vibration, maintain the tool as  
explained in this manual. If any abnormal  
vibration occurs, stop use immediately.  
(See 3-Prong Plug and Outlet.)  
Double insulated tools:  
Save tHeSe  
tools with two Prong Plugs  
inStRuCtiOnS.  
Grounding  
tO PRevent eleCtRiC SHOCK anD  
DeatH FROm inCORReCt GROunDinG  
WiRe COnneCtiOn:  
Outlets for 2-Prong Plug  
Check with a qualified electrician if you are  
in doubt as to whether the outlet is properly  
grounded. Do not modify the power cord plug  
provided with the tool. never remove the grounding  
prong from the plug. Do not use the tool if the power  
cord or plug is damaged. if damaged, have it  
repaired by a service facility before use. if the plug  
will not fit the outlet, have a proper outlet installed by  
a qualified electrician.  
1. Tools marked “Double Insulated” do not  
require grounding. They have a special  
double insulation system which satisfies  
OSHA requirements and complies with  
the applicable standards of Underwriters  
Laboratories, Inc., the Canadian Standard  
Association, and the National Electrical Code.  
2. Double insulated tools may be used in either of the  
120 volt outlets shown in the preceding illustration.  
(See Outlets for 2-Prong Plug.)  
Grounded tools:  
tools with three Prong Plugs  
extension Cords  
1. Grounded tools require a three wire extension  
cord. Double Insulated tools can use either  
a two or three wire extension cord.  
2. As the distance from the supply outlet increases,  
you must use a heavier gauge extension  
cord. Using extension cords with inadequately  
sized wire causes a serious drop in voltage,  
resulting in loss of power and possible tool  
damage. (See table a on page 6.)  
3-Prong Plug and Outlet  
3. The smaller the gauge number of the wire, the  
greater the capacity of the cord. For example,  
a 14 gauge cord can carry a higher current  
than a 16 gauge cord. (See table a.)  
1. Tools marked with “Grounding Required” have a three  
wire cord and three prong grounding plug. The plug  
must be connected to a properly grounded outlet.  
If the tool should electrically malfunction or break  
SKU 68341  
For technical questions, please call 1-800-444-3353.  
Page 5  
 
4. When using more than one extension cord to make  
up the total length, make sure each cord contains at  
least the minimum wire size required. (See table a.)  
Symbology  
Double Insulated  
5. If you are using one extension cord for more  
than one tool, add the nameplate amperes  
and use the sum to determine the required  
minimum cord size. (See table a.)  
Canadian Standards Association  
Underwriters Laboratories, Inc.  
Volts Alternating Current  
6. If you are using an extension cord outdoors, make  
sure it is marked with the suffix “W-A” (“W” in  
Canada) to indicate it is acceptable for outdoor use.  
v~  
a
7. Make sure the extension cord is properly wired  
and in good electrical condition. Always replace  
a damaged extension cord or have it repaired  
by a qualified electrician before using it.  
Amperes  
No Load Revolutions per Minute (RPM)  
n xxxx/min.  
0
8. Protect the extension cords from sharp objects,  
excessive heat, and damp or wet areas.  
WARNING marking concerning Risk  
of Eye Injury. Wear ANSI-approved  
safety goggles with side shields.  
taBle a: ReCOmmenDeD minimum  
WiRe GauGe FOR eXtenSiOn CORDS*  
Read the manual before  
set-up and/or use.  
(120/240 vOlt)  
eXtenSiOn CORD  
lenGtH  
namePlate  
WARNING marking concerning  
Risk of Hearing Loss.  
Wear hearing protection.  
amPeReS  
(at full load)  
25´ 50´ 75´ 100´ 150´  
0 – 2.0  
2.1 – 3.4  
18  
18  
18  
18  
18  
14  
12  
18  
18  
18  
16  
14  
12  
10  
18  
18  
16  
14  
12  
10  
-
18  
16  
14  
12  
10  
-
16  
14  
12  
12  
-
WARNING marking  
concerning Risk of Fire.  
Do not cover ventilation ducts.  
Keep flammable objects away.  
WARNING marking concerning  
Risk of Electric Shock.  
3.5 – 5.0  
5.1 – 7.0  
7.1 – 12.0  
12.1 – 16.0  
16.1 – 20.0  
-
Properly connect power cord  
to appropriate outlet.  
-
-
* Based on limiting the line voltage drop to five volts at  
150% of the rated amperes.  
Page 6  
For technical questions, please call 1-800-444-3353.  
SKU 68341  
 
instructions for Putting into use  
Read the entiRe imPORtant  
tO PRevent SeRiOuS  
injuRy FROm  
aCCiDental OPeRatiOn:  
SaFety inFORmatiOn section at the  
beginning of this manual including  
all text under subheadings therein  
before set up or use of this product.  
turn the Power Switch off and unplug the Router  
before adjusting or installing accessories.  
note: For additional information regarding the parts listed in the following pages, refer to Parts List on page 12.  
Components  
Power Switch (23)  
Scale  
Ring (46)  
Handle  
Handle  
Figure 1  
Collet Nut (1)  
SKU 68341  
For technical questions, please call 1-800-444-3353.  
Page 7  
 
Operating instructions  
tO PRevent SeRiOuS  
injuRy FROm  
aCCiDental OPeRatiOn:  
Read the entiRe imPORtant  
SaFety inFORmatiOn section at the  
beginning of this manual including  
all text under subheadings therein  
before set up or use of this product.  
turn the Power Switch off and unplug the Router  
before adjusting or installing accessories.  
tool Set up  
installing Bits  
Unlock the Lock Lever (30).  
Rotate the Main Housing to raise or  
lower the Spindle so you can access the  
Spindle and Collet Nut with the Wrenches.  
1
2
Main  
Housing  
(5)  
Lock Lever  
(30)  
Spindle  
Turn the Router upside down and hold the  
Spindle in place with the Spindle Wrench  
while turning the Collet Nut counterclockwise with  
the Collet Nut Wrench to loosen the Collet Nut.  
Remove or insert a Collet Chuck as needed  
to fit the bit size, then insert the bit (sold  
3
4
separately)  
and tighten the  
Collet Nut with  
Bit  
(sold separately)  
the Wrenches.  
Collet Nut  
Wrench (51)  
Collet  
Nut (1)  
Collet Nut  
Wrench (51)  
Collet  
Nut (1)  
Spindle  
Wrench (50)  
Spindle  
Wrench (50)  
Spindle  
Spindle  
Page 8  
For technical questions, please call 1-800-444-3353.  
SKU 68341  
 
adjusting the Cutting Depth  
Rotate the Main Housing until the  
tip of the bit touches the workpiece  
surface. Lock the Lock Lever.  
Place the router on a flat wood  
surface. Unlock the Lock Lever (30).  
2
1
Main  
Housing  
(5)  
Lock Lever  
(30)  
Spindle  
Slide the Scale Ring until the “0” aligns with  
the index line (vertical mark) on the Main  
Housing. Unlock the Lock Lever. Each line on  
the scale raises or lowers the bit by 1/64".  
While holding the Base up from the  
surface, rotate the Main Housing to  
raise or lower the bit until the index line on  
the housing aligns with the desired depth  
on the scale ring. Lock the Lock Lever.  
3
4
Index Line  
(vertical mark on  
Main Housing)  
Scale Ring  
Lock Lever  
(30)  
attaching Guide  
To attach the Guide (24) when making straight cuts:  
Wing  
Nuts (37)  
1. Loosen the four Wing Nuts (27 and 37).  
Guide (24)  
Wing Nuts (27)  
2. Slide the Guide Poles (28) on the Guide (24)  
into the slots on the Base of the Router  
with the Guide facing the workpiece.  
3. Adjust the distance between the router bit  
and the Guide to the desired setting.  
4. Tighten the Wing Nuts (27 and 37).  
Base  
(45)  
Guide Poles (28)  
SKU 68341  
For technical questions, please call 1-800-444-3353.  
Page 9  
 
note: Make practice cuts at different speeds in scrap  
material until you are able to produce a smooth  
cut with no burnishing or burn marks. Burn marks  
are caused by moving too slowly through the  
wood. Feeding the Router too quickly, or trying to  
remove too much material in a single pass creates  
a rough cut and can overload the motor.  
Work Piece and Work  
area Set up  
1. Designate a work area that is clean and well-lit.  
The work area must not allow access by children  
or pets to prevent distraction and injury.  
2. Route the power cord along a safe route to reach  
the work area without creating a tripping hazard or  
exposing the power cord to possible damage. The  
power cord must reach the work area with enough  
extra length to allow free movement while working.  
WaRninG! When first turning on the Router,  
grip the Handles firmly as the tool may try  
to twist from the strong initial torque.  
1. Hold the Router handles firmly with both hands.  
2. Place the Router directly above the point  
you plan to cut. Verify that there are no  
obstructions in the cutting path.  
3. Secure loose work pieces using a vise or clamps  
(not included) to prevent movement while working.  
4. Make sure there are no metal objects in the wood  
which might make contact with the router bit.  
3. Turn on the Router.  
4. Before cutting material, watch and feel for  
vibration which could indicate an improperly  
installed bit. Turn off and re-install bit, if needed.  
General Operating instructions  
note: Use two or more passes for deep cuts, especially  
in the case of hardwood. Do not attempt to cut deeper  
than 5/8” in a single pass. Adjust the cutting depth so  
that the first pass will be less than 5/8” deep, then follow  
the procedures for Adjusting the Cutting Depth for each  
progressive pass, until the final depth is achieved.  
5. Allow the bit to come to full speed,  
slowly engage material. DO NOT force  
the Router down into the material.  
note: Feed the Router bit into the workpiece  
against the bit’s direction of rotation.  
view from top of piece  
Bit revolving direction  
Feed direction  
view from cutting edge of piece  
Bit revolving direction  
6. When finished, raise the Router so the bit is clear  
of the material, then turn the Power Switch off.  
Do not set the Router down until the  
Feed direction  
bit has come to a complete stop.  
When cutting outside edges, guide the router  
counterclockwise around the workpiece.  
Move it clockwise when cutting inside edges.  
7. Do not touch the bit right after cutting. It becomes  
very hot. Allow to cool before changing bits.  
8. Do not leave the router running when not  
actually cutting. Turn power off between cuts.  
9. To prevent accidents, disconnect the power  
supply after use. Clean, then store the  
tool indoors out of children’s reach.  
Router  
Direction  
WaRninG! moving the router against  
the recommended direction can cause  
serious injury from kickback.  
Page 10  
For technical questions, please call 1-800-444-3353.  
SKU 68341  
 
maintenance and Servicing  
Procedures not specifically explained  
in this manual must be performed  
only by a qualified technician.  
tO PRevent SeRiOuS  
injuRy FROm  
tO PRevent SeRiOuS injuRy  
FROm tOOl FailuRe:  
aCCiDental OPeRatiOn:  
Do not use damaged equipment. if abnormal  
noise or vibration occurs, have the  
problem corrected before further use.  
turn the Power Switch off and unplug the  
Router before performing any inspection,  
maintenance, or cleaning procedures.  
Cleaning, maintenance,  
and lubrication  
4.  
WaRninG! if the supply cord of this power  
tool is damaged, it must be replaced only by a  
qualified service technician.  
1. BeFORe eaCH uSe, inspect the general condition  
of the tool. Check for loose hardware, misalignment  
or binding of moving parts, cracked or broken  
parts, damaged electrical wiring, and any other  
condition that may affect its safe operation.  
Replacing Carbon Brushes  
Remove and check the Carbon Brushes regularly.  
Replace when they wear down to the limit mark on  
the carbon. Replace both  
brushes at the same time.  
To replace: Remove the Brush  
Caps and old brushes, then  
insert the new brushes and  
secure the caps in place.  
Brush  
Cap  
(15)  
2. aFteR uSe, wipe external surfaces  
of the tool with clean cloth.  
3. Regularly clean all ventilation openings by  
periodically brushing with a soft brush and/  
or blowing clear with compressed air.  
Carbon  
Brush  
(18)  
Limit mark  
troubleshooting  
Problem  
Tool will not start.  
Possible Causes  
1. Cord not connected.  
likely Solutions  
1. Check that cord is plugged in.  
2. No power at outlet.  
2. Check power at outlet. If outlet is unpowered, turn off tool  
and check circuit breaker. If breaker is tripped, make sure  
circuit is right capacity for tool and circuit has no other loads.  
3. Tool’s thermal reset breaker  
tripped (if equipped).  
3. Turn off tool and allow to cool. Press reset button on tool.  
4. Internal damage or wear. (Carbon 4. Have technician service tool.  
brushes or switch, for example.)  
Tool operates slowly. Extension cord too long or  
wire size too small.  
Eliminate use of extension cord. If an extension cord is  
needed, use shorter/heavier gauge cord. See Extension  
Cords in Grounding section on page 5.  
Performance  
1. Accessory dull or damaged.  
1. Keep cutting accessories sharp. Replace as needed.  
decreases over time.  
2. Carbon brushes worn or damaged. 2. Have qualified technician replace brushes.  
Excessive noise  
or rattling.  
Overheating.  
Internal damage or wear. (Carbon  
brushes or bearings, for example.)  
1. Forcing tool to work too fast.  
Have technician service tool.  
1. Allow tool to work at its own rate.  
2. Accessory misaligned.  
2. Check and correct accessory to fence and/or table alignment.  
3. Keep cutting accessories sharp. Replace as needed.  
3. Accessory dull or damaged.  
4. Blocked motor housing vents.  
4. Wear ANSI-approved safety goggles and  
NIOSH-approved dust mask/respirator while blowing  
dust out of motor using compressed air.  
5. Motor being strained by long or  
small diameter extension cord.  
5. Eliminate use of extension cord. If an extension cord is needed,  
use one with the proper diameter for its length and load. See  
Extension Cords in Grounding section on page 5.  
Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect power  
supply before service.  
SKU 68341  
For technical questions, please call 1-800-444-3353.  
Page 11  
 
Parts list  
Part  
Description  
Qty  
1
2
1
1
1
2
1
1
1
1
1
1
1
1
2
2
2
2
2
1
2
1
4
1
1
2
Part  
Description  
Qty  
2
2
2
1
1
1
1
1
4
1
2
2
1
3
1
4
1
1
3
1
1
1
1
1
1
1
2
3
4
5
6
7
8
9
Collet Nut  
Bolt  
26 Spring  
27 Wing Nut  
28 Guide Pole  
29 Pin  
30 Lock Lever  
31 Nut  
32 Block  
33 Bolt  
34 Screw  
35 Right Handle (a)  
36 Spring  
Bearing Support  
Bearing  
Main Housing  
Screw  
Cover  
Stator  
Rotor  
10 Washer  
11 Bearing  
12 Motor Housing  
13 Power Cord  
14 Cable Guard  
15 Brush Cap  
16 Brush Holder  
17 Spring  
18 Carbon Brush (installed)  
18a Carbon Brush (replacement)  
19 Cable Clamp  
20 Screw  
37 Wing Nut  
38 Right Handle (b)  
39 Flat Cap Screw  
40 Base Slider  
41 Screw  
42 Left Handle (a)  
43 Left Handle (b)  
44 Clinch Bolt  
45 Base  
46 Scale Ring  
47 1/4" Collet Chuck (not shown)  
48 3/8" Collet Chuck (not shown)  
50 Spindle Wrench (not shown)  
51 Collet Nut Wrench (not shown)  
21 Rear Housing  
22 Screw  
23 Power Switch  
24 Guide  
25 Nut  
Record Product’s Serial number Here:  
note: If product has no serial number, record month and year of purchase instead.  
note: Some parts are listed and shown for illustration purposes only,  
and are not available individually as replacement parts.  
PleaSe ReaD tHe FOllOWinG CaReFully  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM  
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR  
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS  
qUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE  
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY  
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND  
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY  
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS  
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.  
Page 12  
For technical questions, please call 1-800-444-3353.  
SKU 68341  
 
assembly Diagram  
SKU 68341  
For technical questions, please call 1-800-444-3353.  
Page 13  
 
limited 90 Day Warranty  
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability  
standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship  
for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or  
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity,  
improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death,  
injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use  
of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the  
above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESSLY IN LIEU OF ALL OTHER  
WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.  
To take advantage of this warranty, the product or part must be returned to us with transportation  
charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.  
If our inspection verifies the defect, we will either repair or replace the product at our election or we may  
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will  
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted  
from causes not within the scope of our warranty, then you must bear the cost of returning the product.  
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353  
 

Grizzly Drill G9969 User Manual
HANNspree Flat Panel Television K229 10U1 001 User Manual
Harbor Freight Tools Hunting Equipment 47894 User Manual
Honeywell Smoke Alarm 800 04433V1 User Manual
Honeywell Stud Sensor C7089 User Manual
Honeywell Thermostat Y594G User Manual
Hotpoint Clothes Dryer TCYM 750C User Manual
HP Hewlett Packard Network Card A5799A User Manual
HP Hewlett Packard Tablet TC1100HP User Manual
Hunter Fan Air Cleaner 30849 User Manual