HP Hewlett Packard Headphones HP Bluetooth Stereo Headphones User Manual

User’s Guide  
HP iPAQ Bluetooth Stereo Headphones  
Document Part Number: 378962-001  
November 2004  
 
CAUTION: Do not wear HP iPAQ Bluetooth Stereo Headphones  
while operating a motor vehicle or in an area in which it is  
dangerous for your hearing to be impaired.  
Getting to Know Your HP iPAQ  
Bluetooth Stereo Headphones  
Button  
Function  
Forward  
Tap to track forward to the next media file in the  
playlist.  
Back  
Tap to track backward to the previous file in the  
playlist.  
Volume Up  
Press to increase the volume in the headphones.  
Press to decrease the volume in the headphones.  
Volume down  
Multi Function  
• Press and hold for fifteen seconds to put  
headphones in pairing mode.  
• Press and hold for three seconds to turn  
headphones on or off.  
• Press to pause/unpause audio.  
• After initial Bluetooth pairing, press to reestablish  
connection.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
3
 
Installing the Headphones Driver  
1. Perform a soft reset on your HP iPAQ Pocket PC by pressing  
the Reset button on the back or bottom of the device. For  
more information on performing a soft reset, refer to the  
User’s Guide that came with your HP iPAQ Pocket PC.  
2. Backup your iPAQ Pocket PC using ActiveSync before  
installing the Headphones driver.  
3. If the Bluetooth Radio on your Pocket PC is on, turn it off.  
4. Establish a connection from your iPAQ Pocket PC to your  
desktop computer via ActiveSync. Refer to the User’s Guide  
that came with your iPAQ Pocket PC for instructions.  
5. Place the CD that came with your HP iPAQ Bluetooth Stereo  
Headphones into an optical drive on your computer.  
6. Click the button that reads “  
and follow the instructions on your screen. If asked to reset  
your Pocket PC, tap  
7. Once the unit is reset, the driver is installed.  
Pairing the Headphones with a Pocket  
PC  
Before you can use the HP iPAQ Bluetooth Stereo Headphones,  
you must first pair them with an iPAQ Pocket PC with Bluetooth.  
To pair your headphones to a Pocket PC:  
1. Make sure the batteries are charged on both the headphones  
and the HP iPAQ Pocket PC.  
2. Make sure the headphones are turned off by pressing the  
Multi Function button in the center of the right earpiece of the  
headphones for about three seconds until the light flashes red  
and goes off.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
4
 
3. On your Pocket PC, tap the  
bottom right of the screen  
Bluetooth icon  
icon on the  
or, for older models, tap the  
4. Turn on the Bluetooth Radio by tapping the Bluetooth icon.  
For older iPAQ Pocket PCs, turn on the Bluetooth Radio by  
tapping selecting “Turn Bluetooth ON” from the dropdown  
box in the bottom right corner of the screen.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
5
 
5. Tap the  
button in the Bluetooth section of the  
screen. For older iPAQ Pocket PC Models, tap the Bluetooth  
icon at the bottom right of the screen, and open the Bluetooth  
Manager. The following screen should appear:  
6. On the headphones, press and hold the Multi Function button  
in the center of the right earpiece for ten to fifteen seconds  
until the light flashes red and blue.  
7. The headphones are now in Pairing Mode. Release the button.  
The light will continue to flash red and blue.  
8. On the HP iPAQ Pocket PC, select  
from connection types.  
, then  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
6
 
9. An icon will appear for the  
Tap this icon.  
10. When your device discovers the headphones for the first time,  
you will be prompted for a Passkey. The Passkey is 0000  
11. Tap  
12. Tap  
.
13. When pairing is sucessful, the LED on the headphones will  
flash blue.  
14. If no pairing occurs in the next two minutes, the headphones  
will return to stand-by mode, and the LED will flash blue.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
7
 
Reestablishing Connection to the  
Headphones  
Once your headphones have made an initial pairing with the iPAQ  
Pocket PC, you can reestablish the connection easily:  
1. Verify that the iPAQ Pocket PC Bluetooth Radio is turned on.  
2. Turn on the headphones by holding down the Multi Function  
button for about two seconds, until the blue light flashes.  
3. On the iPAQ Pocket PC, play the audio file.  
4. Press the Multi Function button on the right earpiece of the  
headphones. They will re-connect with the Pocket PC and  
you will hear audio through the headphones.  
Note: You can also reconnect the headphones with the iPAQ  
pocket PC by going to the Bluetooth Manager and double tapping  
the High Quality Audio on BT-Headphones  
Turning the Headphones On and Off  
To turn the Bluetooth Headphones on, push and hold the Multi  
Function button for two seconds until the blue light flashes.  
To turn the Bluetooth Headphones off, press and hold the Multi  
Function button for two seconds, until the light flashes red and  
goes off.  
Using the HP iPAQ Bluetooth Stereo  
Headphones  
To play a song or other audio file, ensure that the headphones  
have a Bluetooth connection with the Pocket PC and simply play  
the file on your iPAQ Pocket PC.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
8
 
To pause audio, press the Multi Function button  
To resume play, press the Multi Function button again.  
To track forward, press the Forward button, marked “ ”  
To track backward, press the Back button marked “ “  
To increase the volume, press the Volume Up button marked “ ”  
To decrease the volume, press the Volume Down button  
marked “ ”  
Charging the Headphones  
Note: Headphone batteries are not user replaceable.  
To charge the HP iPAQ Bluetooth Stereo Headphones:  
1. Turn off the headphones by pressing the Multi Function  
button and holding until the light flashes red and goes off.  
2. Connect the Headphones to the power adapter.  
3. Plug the power adapter into an electrical outlet. The amber  
light will come on while the headphones are charging.  
4. When the headphones are fully charged, the light goes off.  
The headphones may take up to four hours to fully charge.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
9
 
Before Calling Technical Support  
Perform a Soft Reset on the HP iPAQ Pocket PC by pressing the  
Reset button on the back or bottom of the HP iPAQ Pocket PC.  
For instructions, see the User’s Guide which came with your HP  
iPAQ Pocket PC.  
Perform a Soft Reset on the HP iPAQ Bluetooth Stereo  
Headphones by placing the tip of the stylus into the round hole  
next to the charging connector on the headphones.  
Technical Support on the Internet  
Support services are available on the Internet through the  
HP Support Forum. You can either browse the postings as a  
guest, or register as a user and submit your own questions. HP  
responds to questions within one business day. To access the HP  
Support Forum, go to the HP website at  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
10  
 
Preparing to Call Technical Support  
If you cannot solve a problem using the tips in this guide or the  
HP Support Forum, you may need to call technical support.  
Contact your local HP authorized dealer, reseller, or service  
provider for the technical support number in your area.  
To receive the fastest possible solution when you call, have the  
following available:  
The Headphones and your Bluetooth device  
Serial numbers for both devices  
Purchase date on your invoice  
Conditions under which the problem occurred  
Error messages that might have appeared  
Hardware configuration information  
Hardware and software you are using  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
11  
 
Wireless Notices  
In some environments, the use of wireless devices may be  
restricted. Such restrictions may apply aboard airplanes, in  
hospitals, near explosives, in hazardous locations, etc. If you are  
uncertain of the policy that applies to the use of this device,  
please ask for authorization to use it prior to turning it on.  
WARNING: Exposure to Radio Frequency Radiation  
The radiated output power of this device is below the FCC radio  
exposure limits. Nevertheless, the device should be used in such a  
manner that the potential for human contact during normal operation  
is minimized.  
Å
FCC Modifications  
The FCC requires the user to be notified that any changes or  
modifications made to this device that are not expressly approved  
by Hewlett-Packard Company may void the user’s authority to  
operate the equipment.  
Canadian Notice  
Operation is subject to the following two conditions: (1) this  
device may not cause interference, and (2) this device must  
accept any interference, including interference that may cause  
undesired operation of the device.  
European Union Regulatory Notice  
This product complies with the following EU Directives:  
Low Voltage Directive 73/23/EEC  
EMC Directive 89/336/EEC  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
12  
 
CE Compliance of this product is valid only if powered  
with the correct HP-provided and CE marked AC Adapter.  
If this product has telecommunication functionality, it also  
complies with the essential requirements of:  
R&TTE Directive 1999/5/EC  
Compliance with these directives implies conformity to  
applicable harmonized European standards (European Norms)  
which are listed on the EU Declaration of Conformity issued by  
Hewlett-Packard for this product or product family.This  
compliance is indicated by the following conformity marking  
placed on the product:  
xxxx*  
This marking is valid for non-Telecom products  
This marking is valid for EU non-harmonized Telecom products .  
and EU harmonized Telecom products (e.g. Bluetooth).  
*Notified body number (used only if applicable - refer to the product label)  
The telecommunications functionality of this product may be  
used in the following EU and EFTA countries: Austria, Belgium,  
Cypress, Czech Republic, Denmark, Estonia, Finland, France,  
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,  
Lichtenstein, Lithuania, Luxembourg, Malta, Netherlands,  
Norway, Poland, Portugal, Slovak Republic, Slovenia, Spain,  
Sweden, Switzerland, and United Kingdom.  
Notice to France and Italy for Use of  
2.4 GHz Wireless Communication:  
Italy:  
E’neccessaria una concessione ministeriale anche per l’uso del  
prodotto. Verifici per favore con il proprio distributore o  
direttamente presso la Direzione Generale Pianificazione e  
Gestione Frequenze.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
13  
 
Lisence required for use. Verify with your dealer or directly with  
General Direction for Frequency Planning and Management  
(Direzione Generale Pianificazione e Gestione Frequenze).  
France:  
Lutilisation de cet equipment (2.4 GHz Wireless LAN) est  
soumise a certaines restrictions: Cet Equipment peut etre utilise a  
Linterieur d’un batiment en utilisant toutes les frequences de  
2400 a 2483.5 MHz (Chaine 1-13). Pour une utilisation en  
environment sxterieur, vous devez utiliser les frequences  
comprises entre 2454-2483.5 MHz (Chaine 10-13). Pour les  
For 2.4 GHz Wireless LAN operatin of this product, certain  
restrictions apply: This product may be used indoors for the entire  
2400-2483.5 MHz frequency band (channels 1-13). For outdoor  
use, only 2454-2483.5 MHz may be used. For the latest  
Brazilian Regulatory Notice  
Este equipamento opera em caráter secundário, isto é, não tem  
direito a proteção contra interferência prejudicial, mesmo de  
estações do mesmo tipo, e não pode causar interferência  
aproteção contra interferência a sistemas operando em caráter  
primário.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
14  
 
Japanese Regulatory Wireless Notice  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
15  
 
Battery Warning  
WARNING: This device contains a lithium ion rechargeable  
battery. To reduce the risk of fire or burns, do not disassemble,  
crush, puncture, short external contacts, or dispose of in fire or water  
Å
WARNING: To reduce the risk of personal injury, electrical shock, fire or  
damage to the equipment:  
Plug the AC Adapter into an electrical outlet that is easily  
accessible at all times.  
Disconnect power from the equipment by unplugging the AC  
Adapter from the electrical outlet or unplugging the  
Synchronization cable from the host computer.  
Do not place anything on the AC Adapter cord or any of the  
other cables. Arrange them so that no one may accidentally step  
on or trip over them.  
Do not pull on a cord or cable. When unplugging from the  
electrical outlet, grasp the cord by the plug or, in the case of the  
AC Adapter, grasp the AC Adapter and pull out from the  
electrical outlet.  
Do not use converter kits sold for appliances to power your iPAQ  
Pocket PC.  
HP iPAQ Bluetooth Stereo Headphones User’s Guide  
16  
 

Grizzly Lathe G0657 G0658 User Manual
Grundig DVD Player UMS 4401 SPCD User Manual
Haier Oven RTO1400SS User Manual
Handspring Personal Computer Handheld Desktop User Manual
HANNspree Flat Panel Television F001 15U1 000 User Manual
Honeywell Thermostat EC7895A User Manual
Hotpoint Range RGB530DEP User Manual
Hunter Fan Thermostat 44372 User Manual
Hyundai Car Video System B70D User Manual
Image Home Gym IMBE40890 User Manual