Graco Inc Paint Sprayer 12004 User Manual

Instructions-Parts List  
Pistol Grip Flow Gun  
309739D  
For dispensing ambient temperature sealants and adhesives.  
Important Safety Instructions  
Read all warnings and instructions in this manual.  
Save these instructions.  
See page 2 for part numbers and maxumum work-  
ing pressure.  
Models 12004 and 12005  
Model 12004X  
Model 12006  
 
Warnings  
Warnings  
Warning  
ELECTRIC SHOCK HAZARD  
Improper grounding, setup, or usage of the system can cause electric shock.  
Turn off and disconnect power at main switch before disconnecting any cables and before servicing  
equipment.  
All electrical wiring must be done by a qualified electrician and comply with all local codes and regu-  
lations.  
Connect only to grounded power source.  
SKIN INJECTION HAZARD  
High pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just  
a cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.  
Do not point gun at anyone or at any part of the body.  
Do not put your hand over the spray tip.  
Do not stop or deflect leaks with your hand, body, glove, or rag.  
Engage trigger lock when not spraying.  
Follow Pressure Relief Procedure on page 5 if the nozzle clogs and before cleaning, checking or  
servicing equipment.  
TOXIC FLUID HAZARD  
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on the skin, inhaled, or  
swallowed.  
Read MSDS’s to know the specific hazards of the fluids you are using.  
Store hazardous fluid in approved containers and dispose of it according to applicable guidelines.  
EQUIPMENT MISUSE HAZARD  
Equipment misuse can cause death or serious injury.  
Do not exceed maximum working pressure or temperature rating of lowest rated system component.  
See Technical Data in all equipment manuals.  
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all  
equipment manuals. Read fluid and solvent manufacturers warnings.  
Check equipment daily. Repair or replace worn or damaged parts immediately.  
Do not alter or modify equipment.  
For professional use only.  
Use equipment only for its intended purpose. Call your Graco distributor for information.  
Route hoses away from traffic areas, sharp edges, moving parts and hot surfaces.  
Do not use hoses to pull equipment.  
309739  
3
 
Grounding and Electrical Requirements  
Grounding and Electrical Requirements  
1. Pump: connect a ground wire and clamp to a true  
earth ground as shown in pump manual.  
2. Applicator: ground through motor cable assembly.  
3. Fluid and air hoses: only use electrically conduc-  
The following are minimum requirements for a basic dis-  
pensing system. Your system may include other equip-  
ment or objects that must be grounded. Check your local  
electrical code for detailed grounding instructions for  
your area and type of equipment.  
tive material and air hoses.  
4. Dispense gun: ground through connection of hose  
or cable.  
5. Air compressor: follow manufacturer’s recommen-  
dations.  
To maintain grounding continuity when flushing or reliev-  
ing pressure, always hold a metal part of spray gun  
firmly to side of a grounded metal pail. Then trigger  
spray gun.  
6. Object being sprayed: refer to local code.  
7. Fluid supply container: refer to local code.  
8. Solvent pails used for flushing: refer to local  
code.  
ti3795a  
4
309739  
 
Installation  
Installation  
Inspect flow gun for shipping damage. If damage is  
found notify the carrier immediately.  
If you suspect the tip/nozzle or hose is completely  
clogged or that pressure has not been fully relieved after  
following the above steps, VERY SLOWLY loosen the  
retaining nut or hose end coupling to relieve pressure  
gradually. Then loosen it completely. Clear tip/nozzle or  
hose.  
If material hose will be suspended by a hanger or  
tool balancer, route hose through the suspension  
device before securing each end of material hose.  
1. Connect flow gun to any standard Graco hose  
assembly.  
Trigger Lock  
Always engage trigger lock when you stop dispensing to  
prevent gun from being triggered accidentally by hand or  
if dropped or bumped.  
2. Connect the opposite end of the heated hose  
assembly to any fluid supply system. See Model  
table, page 2 for maximum fluid working pressure  
for your gun model.  
To engage trigger lock, release trigger and rotate lock  
downward. See Fig. 1.  
3. Tighten fluid connections.  
4. Before operating gun, squeeze and release trigger a  
few cycles. Observe action of cartridge assembly.  
Do not try to force trigger valve open with trigger  
lock engaged. This could result in component fail-  
ure.  
Pressure Relief Procedure  
To help prevent injuries, follow this procedure  
when you shut off the flow gun and before check-  
ing or adjusting any part of gun.  
Trigger Lock  
Engaged  
FIG. 1: Trigger Lock Engaged  
1. Shut off air to pump.  
2. Close bleed-type master air valve (required in your  
system).  
To disengage trigger lock, rotate it upward. See Fig. 2.  
3. Hold metal part of spray gun firmly to side of  
grounded metal pail. Trigger gun to relieve pressure.  
Trigger Lock  
Disengaged  
ti3795a  
FIG. 2: Trigger Lock Disengaged  
4. Open drain valve and/or pump bleeder valve having  
a container ready to catch the drainage.  
5. Leave drain valve open until you are ready to  
spray/dispense again.  
309739  
5
 
 
Troubleshooting  
Troubleshooting  
Problem  
Cause  
Solution  
Gun fails to dispense when trigger is Material lodged in nozzle  
actuated  
Follow Pressure Relief Procedure,  
page 5. Clear nozzle of blockage.  
Material supply, hose, passages,  
clogged  
Check material supply settings,  
hoses, etc. for proper material supply.  
Verify integrity of trigger pin through  
yoke. Repair or replace cartridge  
assembly as necessary.  
Gun fails to dispense when trigger is Tension of trigger needs adjustment Check spring tension adjustment at  
engaged  
rear of gun. Spring tension should be  
adjusted to allow approximately 1/32  
in. of free play on trigger.  
Verify integrity of trigger pin through  
yoke. Repair or replace cartridge  
assembly as necessary.  
Needle and seat adapter loose or  
worn  
Check that seat adapter is tightened  
firmly and flush to gun body.  
Needle and seat adapter worn.  
Replace components as necessary.  
Seal leakage  
Packing adjustment nut not snug  
Follow Pressure Relief Procedure,  
page 5. Tighten packing adjustment  
nut.  
Worn seals and packings  
Worn seals  
Rebuild gun as necessary.  
Replace seals.  
Material leaks from gun inlet swivel  
6
309739  
 
Troubleshooting  
309739  
7
 
Service  
Service  
Reassembly  
Models 12004, 12004X  
Clean all parts thoroughly before reassembling. Check  
them carefully for damage or wear, replacing parts as  
needed. For best results replace the original parts with  
new parts in repair kits.  
Disassembly  
1. Actuate gun to purge material and relieve pressure  
in gun. Pressure Relief Procedure, page 5.  
2. Disconnect material supply line from gun handle.  
Prior to assembly, lubricate all seals and o-rings with  
PARKER-O-LUBE or an equivalent lubricant.  
3. Hold adapter (9) stationary and unscrew nozzle and  
collar (16).  
1. Push seals (6) in the packing nut (5).  
4. With trigger depressed, unscrew adapter (9) from  
gun body (17).  
2. Screw adjusting screw (3) into packing nut (5).  
Insert needle/ball (8) into packing support (7).  
5. Remove o-ring (10) from adapter (9).  
6. Loosen lock nut (14).  
Nut  
Packing Nut  
7. Carefully unscrew and remove spring retainer (15)  
and spring (13) from the gun body (17).  
Packing Support  
8. Remove screw (11) and lock washer (23) from side  
of trigger (18).  
Needle/ball  
Yoke  
9. Pull trigger pins (12) from gun body (17) and remove  
trigger (18).  
Adjusting Screw  
10. Unscrew packing nut (5) from gun body (17).  
Seal  
ti3810a  
O-Ring  
11. Remove cartridge assembly through side of gun  
handle.  
3. Attach needle/ball (8) to yoke (1) using slot in the  
yoke to screw needle/ball.  
Cartridge Disassembly Procedure  
4. Secure yoke in soft jawed vice. Tighten lock nut to  
cartridge.  
1. Remove o-ring (4) from groove on packing nut (5).  
2. Loosen lock nut (14) on cartridge while holding yoke  
(1) in a soft  
5. Install o-ring (4) onto groove in packing nut (5).  
6. Insert cartridge assembly through front of gun han-  
dle.  
3. Separate needle/ball (8) from yoke (1) using the slot  
in needle/ball to unscrew the yoke.  
7. Screw packing nut (5) in gun body (17).  
4. Remove adjusting screw (3) from packing nut (5).  
Then, separate needle/ball (8) from packing support  
(7).  
8. Install trigger (18) and insert trigger pins (12) in gun  
body (17). Secure using screws (11) and lock wash-  
ers (23).  
5. Push seals (6) out of packing nut (5).  
9. Install snap rings (11) from top to bottom to secure  
trigger pins (12).  
Nut  
Packing Nut  
10. Install spring (13) and spring retainer (15) into the  
gun body (17). Adjust spring retainer to allow  
approximately 1/32 in. of free play on trigger.  
Packing Support  
Needle/ball  
11. Tighten lock nut (14).  
Yoke  
12. Install o-ring (10) to adapter (9).  
13. With trigger retracted, screw adapter (9) into gun  
body (17).  
Adjusting Screw  
Seal  
ti3810a  
O-Ring  
8
309739  
 
Service  
14. Hold adapter (9) stationary and screw nozzle and  
collar (16) into adapter. Do not over tighten collar.  
Cartridge Disassembly Procedure  
1. Remove guide (22) from needle (8).  
15. Reconnect flow gun to material supply line.  
16. Turn on material supply line.  
17. Return flow gun to normal operating condition.  
ti4035a  
Model 12005  
2. Remove two o-rings (23) from guide (22).  
Disassembly  
1. Actuate gun to purge material and relieve pressure  
in gun. Pressure Relief Procedure, page 5.  
2. Disconnect material supply line from gun handle.  
3. Hold adapter (9) stationary and unscrew nozzle and  
collar (16).  
ti4036a  
3. Unwind spiral PTFE o-ring backup (21) from  
guide(22).  
4. With trigger depressed, unscrew adapter (9) from  
gun body (17).  
4. Loosen adjustment screw (3) while holding packing  
nut (5).  
5. Remove o-ring (10) from adapter (9).  
6. Loosen lock nut (14).  
5. Extract needle (8) from packing nut (5).  
6. Remove o-ring (4) from groove in packing nut (5).  
7. Remove adjustment screw (3).  
7. Carefully unscrew and remove spring retainer (15)  
8. Remove screws (11) and lock washers (28) from  
trigger pins (12).  
8. Push three seal-needles (6) out of packing nut (5)  
with soft rod or dowel.  
9. Pull trigger pins (12) from gun body (17) and remove  
trigger (18).  
10. Remove piston valve (20) from front of gun.  
11. Unscrew packing nut (5) from gun body (17).  
12. Remove cartridge assembly from gun.  
ti4039a  
9. Hold yoke (1) in soft-jawed vice. Unlock stop nut (2).  
ti4040a  
10. Separate needle (8) from yoke (1).  
309739  
9
 
Service  
12. Tighten nut (19) on needle (8).  
Reassembly  
Clean all parts thoroughly before reassembling. Check  
them carefully for damage or wear, replacing parts as  
needed. For best results replace the original parts with  
new parts in repair kits.  
Prior to assembly, lubricate all seals and o-rings with  
PARKER-O-LUBE or an equivalent lubricant.  
ti4051a  
1. Connect needle (8) and stop nut (2) to yoke (1).  
2. Secure yoke (1) in soft jawed vise. Lock stop nut (2)  
against yoke.  
13. Adjust screw (3) to tighten packings.  
14. Install trigger (18). Align yoke (1) in gun body (17).  
15. Press trigger pin (12) into gun body.  
16. Secure trigger pins (12) using screws (11) and lock  
washers (28).  
17. Install spring (13) and spring retainer (15) into gun  
body (17).  
ti4043a  
18. Adjust spring retainer to allow approximately 1/32 in.  
of free play on trigger.  
3. Insert needle (8) into packing nut (5).  
4. Push three seal needles (6) in packing nut (5) using  
soft rod or dowel. Orient as shown below  
19. Tighten stop nut (14).  
20. Install o-ring (10) on adapter (9).  
21. With trigger retracted screw adapter (9) on gun body  
(17).  
22. While holding adapter (9) stationary, screw collar  
(16) and nozzle into adapter. Do not over tighten  
collar.  
23. Reconnect flow gun to material supply line.  
24. Turn on material supply line to gun.  
ti4045a  
5. Install o-ring (4) on groove of packing nut (5).  
6. Install guide (22) on needle (8).  
25. Return flow gun to normal operating condition.  
7. Rewind spiral o-ring backup (21) on guide (22).  
8. Install two o-rings (23) on guide (22).  
9. Insert cartridge assembly in gun body (17) from rear  
of gun.  
10. Screw packing nut (5) into gun body (17).  
11. Insert valve (20) through front of gun on needle (8).  
ti4050a  
10  
309739  
 
Service  
Reassembly  
Model 12006  
Clean all parts thoroughly before reassembling. Check  
them carefully for damage or wear. Replace parts as  
needed. For best results replace the original parts with  
new parts in repair kits.  
Disassembly  
1. With trigger (20) depressed, remove collar (17)  
securing nozzle (18) to gun.  
Prior to assembly, lubricate all seals and o-rings with  
PARKER-O-LUBE or an equivalent lubricant.  
2. Remove nozzle (18), holding adapter (10) firmly to  
prevent it from turning.  
3. Remove gasket (9). Clean and inspect for damage.  
4. Remove adapter (10) from gun body.  
1. Replace o-ring (5) and seals (4) in packing nut (6).  
Nut  
5. Remove both screws (12) and lock washers (25) on  
one side of trigger (20) and push both trigger pins  
(13) out of body.  
Packing Nut  
Packing Support  
6. Loosen lock nut (15) at rear of gun.  
Needle  
7. Unthread spring retainer (16) and remove spring  
(14).  
Yoke  
8. Loosen and remove adjustment screw (6) on pack-  
ing nut (3) and pull needle assembly from rear of  
gun. Inspect for damage, replace if needed.  
Adjusting Screw  
Seal  
ti4057a  
O-Ring  
9. Remove packing assembly from gun.  
10. Unthread packing nut (3) from body.  
2. Thread packing nut (3) into gun body.  
3. Install packing assembly through rear of gun.  
4. Install needle assembly through rear of gun.  
11. Remove adjustment screw (6) and o-ring (5) and  
seals (4).  
5. Install spring (14) and spring retainer (16) into gun  
body. Adjust spring retainer to allow approximately  
1/32 in. of free play on trigger.  
6. Tighten lock nut (15).  
7. Install trigger (20) and insert trigger pins (13) in gun  
body.  
8. Secure trigger pins (13) using screws (12) and lock  
washers (25).  
9. Replace o-ring (11). Lubricate with petroleum jelly to  
aid in reassembly.  
10. With trigger (20) retracted, screw adapter (10) into  
gun body.  
11. Insert gasket (9) in collar (17).  
12. While holding adapter stationary, screw collar (17)  
and nozzle (18) into adapter. Do not overtighten col-  
lar.  
13. Reconnect flow gun to material supply line.  
14. Turn on material supply line.  
15. Return flow gun to normal operating condition.  
309739  
11  
 
Parts  
Parts  
Models 12004 & 12004X  
13  
1
2
3
5
6
7
4
14  
15  
10  
9
21  
19  
16  
20  
12  
17  
8
11  
23  
18  
Item Part No. Description  
Qty  
Item Part No. Description  
Qty  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
C00020 SPRING  
C27036 NUT, lock  
C27037 RETAINER, spring  
C00004 COLLAR  
C27049 BODY, flow gun  
C27051 TRIGGER, hot melt  
C34009 TRIGGER, lock  
108483 SCREW, shoulder, sch  
C20565 WASHER, spring  
070269 SEALANT, anaerobic  
C19208 LOCKWASHER  
1
1
1
1
1
1
1
1
1
1
2
C27052 YOKE  
100284 NUT, hex (model 12004)  
C19284 NUT, hex (model 12004-X)  
C27061 SCREW, adjustment  
106555 PACKING, o-ring  
C27058 PACKING, nut  
1
1
1
1
1
1
3
1
1
1
1
3
4
5
6
7
8
C27060 SEAL, needle  
C27053 SUPPORT, packing  
C27038 NEEDLE  
9
10  
11  
C27063 ADAPTER, ball seat  
C20102 PACKING, o-ring  
C19950 SCREW, cap, sch  
(model 12004)  
2
3
1
(model 12004-X)  
101369 WRENCH, hex key, 3/32 in.  
(not shown)  
(model 12004)  
(model 12004-X)  
2
3
2
3
24  
12  
15X116 PIN, trigger (model 12004)  
(model 12004-X)  
12  
309739  
 
Parts  
Model 12005  
13  
1
2
3
10  
5
9
6
4
16  
14  
15  
17  
27  
24  
25  
22  
8
23  
21  
12  
20  
19  
11  
28  
18  
Item Part No. Description  
Qty  
Item Part No. Description  
Qty  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
C00004 COLLAR  
1
1
1
1
1
1
1
2
1
1
1
1
2
C27052 YOKE  
C19284 NUT, hex  
1
1
1
1
1
3
1
1
1
2
2
1
1
1
C27049 BODY, flow gun  
C27051 TRIGGER, hot melt  
C27076 NUT  
C27072 VALVE, piston  
C27074 PACKING, PTFE o-ring  
C27075 GUIDE  
103337 PACKING, o-ring  
C34009 TRIGGER, lock  
108483 SCREW, shoulder, sch  
C20565 WASHER, spring  
070269 SEALANT, anaerobic  
C19208 LOCKWASHER  
101369 WRENCH, hex key, 3/32 in.  
(not shown)  
3
4
5
6
C27061 SCREW, adjustment  
106555 PACKING, o-ring  
C27058 PACKING, nut  
C27060 SEAL, needle  
C27071 NEEDLE  
8
9
C27077 FITTING, adapter  
C20102 PACKING, o-ring  
C19950 RING, snap  
15X116 PIN, trigger  
C00020 SPRING  
C27036 NUT, lock  
C27037 RETAINER, spring  
10  
11  
12  
13  
14  
15  
2
1
309739  
13  
 
Parts  
Model 12006  
14  
8
7
6
3
18  
4
9
2
16  
5
15  
16  
24  
21  
22  
11  
10  
13  
1
12  
25  
20  
Item Part No. Description  
Qty  
Item Part No. Description  
Qty  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
C20102 PACKING, o-ring  
C19950 RING, snap  
15X116 PIN, trigger  
C00020 SPRING  
C27036 NUT, lock  
C27037 RETAINER, spring  
C00004 COLLAR  
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
3
4
C27080 NEEDLE  
1
1
1
3
1
1
1
1
1
1
C27053 SUPPORT, packing  
C27058 PACKING, nut  
C27060 SEAL, needle  
106555 PACKING, o-ring  
5
6
7
C27061 SCREW, adjustment  
C19284 NUT, hex  
C27086 NOZZLE  
8
9
C27052 YOKE  
C02064 GASKET  
C27049 BODY, flow gun  
C27051 TRIGGER, hot melt  
C34009 TRIGGER, lock  
108483 SCREW, shoulder, sch  
C20565 WASHER, spring  
070269 SEALANT, anaerobic  
C19208 LOCKWASHER  
101369 WRENCH, hex key, 3/32 in.  
(not shown)  
10  
C27063 ADAPTER, ball seat  
2
1
14  
309739  
 
Technical Data  
Technical Data  
Maximum fluid working pressure . . . . . . . . . . . . . . . . . . . Models 12004X, 12004, and 12005: 2500 psi (17.2 MPa,  
172 bar)  
Model 12006: 2000 psi (13.79 MPa, 137.9 bar)  
Inlet port size on gun housing . . . . . . . . . . . . . . . . . . . . . 1/2-14 NPT  
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Models 12004X, 12004, and 12005: 1.4 lb (.64 kg)  
Model 12006: 1.6 lb (.73 kg)  
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Height: 7 in. (178 mm)  
Width: 2 in. (51 mm)  
Length:  
Models 12004X, 12004, and 12005: 7 in. (178 mm)  
Model 12006: 9 in. (229 mm)  
Wetted parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Models 12004 and 12004X: aluminum, fluorocarbon  
rubber, carbon steel, tool steel, brass, tetrafluoroethylene  
Model 12005: aluminum, fluorocarbon rubber, carbon  
steel, brass, fluoroelastomer, stainless steel, PTFE,  
tetrafluoroethylene  
Model 12006: aluminum, fluorocarbon rubber, carbon  
steel, brass, tetrafluoroethylene  
CE Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Models 12004X, 12004, and 12005: Yes  
Model 12006: No  
309739  
15  
 
Graco Standard Warranty  
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in  
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty  
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by  
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written  
recommendations.  
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty  
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of  
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with  
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or  
maintenance of structures, accessories, equipment or materials not supplied by Graco.  
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of  
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned  
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will  
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.  
THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED  
TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.  
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy  
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or  
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.  
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT  
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to  
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these  
warranties.  
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or  
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the  
negligence of Graco, or otherwise.  
FOR GRACO CANADA CUSTOMERS  
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,  
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la  
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite  
de ou en rapport, directement ou indirectement, avec les procédures concernées.  
Graco Information  
TO PLACE AN ORDER, contact your Graco distributor or call to identify the nearest distributor.  
Phone: 612-623-6921 or Toll Free: 1-800-328-0211, Fax: 612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication.  
Graco reserves the right to make changes at any time without notice.  
This manual contains English. MM 309739  
Graco Headquarters: Minneapolis  
International Offices: Belgium, China, Japan, Korea  
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441  
Copyright 2002, Graco Inc. is registered to ISO 9001  
Revised 1/2009  
 

Graco Baby Furniture ISPP027AB User Manual
Hach Camcorder 6120118 User Manual
Haier Freezer HFZ 85 User Manual
Heat Glo LifeStyle Indoor Fireplace SL 550TV IPI E User Manual
Honeywell Security Camera HD3MDIH User Manual
Honeywell Thermostat 08161 User Manual
HP Hewlett Packard Cell Phone Accessories E6380 90019 User Manual
HP Hewlett Packard Computer Drive P400 Serial User Manual
Hunter Fan Thermostat 44127 User Manual
hussman Refrigerator ESSS 0303 User Manual