GE Clothes Dryer 333 User Manual

GE Appliances

Dryers

Owner’s Manual

Models Type: 333

453

473

475

GE Answer Center ^®800.626.2000

Part No. 175D1807P277 Pub. No. 49-90010 5–99 JR

500A277P026 Rev-1

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

SafeyIructions

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire

or explosion, electric shock, or to prevent property damage, personal injury, or death.

■ Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

■ Installation and service must be performed

by a qualified installer, service agency or

the gas supplier.

WHAT TO DO IF YOU SMELL GAS:

OpeagIructions

Do not try to light a match, or cigarette, or

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas

supplier’s instructions carefully.

turn on any gas or electrical appliance.

Do not touch any electrical switch; do not

use any phone in your building.

If you cannot reach your gas supplier, call

the fire department.

Clear the room, building or area of all

occupants.

California Safe Drinking Water and Toxic Enforcement Act

This act requires the governor of California to publish a list of substances known to the state to cause cancer,

birth defects or other reproductive harm and requires businesses to warn customers of potential exposure

to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

rubleshotingT

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be

minimized further by properly venting the dryer to the outdoors.

PROPER INSTALLATION

This dryer must be properly installed and located in accordance with the Installation Instructions

before it is used. If you did not receive an Installation Instructions sheet, you can receive one by

calling, toll-free, in the United States the GE Answer Center^®, 800.626.2000. In Canada, call, 1-800-361-3400.

ips

■Properly ground dryer to conform with all

governing codes and ordinances. Follow details in

Installation Instructions.

Exhaust/Ducting:

1 ^{Gas dryers MUST be exhausted to the outside.}

Exhausting electric dryers to the outside is

■Install or store where it will not be exposed to

temperatures below freezing or exposed to the

weather.

strongly recommended to prevent large amounts

CustomSrvice

of moisture and lint from being blown into the

room.

■Connect to a properly rated, protected and sized

power supply circuit to avoid electrical overload.

Use only rigid metal or flexible metal 4″

diameter ductwork inside the dryer cabinet or

■Remove all sharp packing items and dispose of all

shipping materials properly.

for exhausting to the outside. USE OF PLASTIC

OR OTHER COMBUSTIBLE DUCTWORK CAN

CAUSE A FIRE. PUNCTURED DUCTWORK CAN

CAUSE A FIRE IF IT COLLAPSES OR BECOMES

OTHERWISE RESTRICTED IN USE OR DURING

INSTALLATION.

For complete details, follow the Installation

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

YOUR LAUNDRY AREA

■ Keep the area underneath and around your

appliances free of combustible materials, (lint,

paper, rags, etc.), gasoline, chemicals and other

flammable vapors and liquids.

■ Keep all laundry aids (such as detergents,

bleaches, etc.) out of the reach of children,

preferably in a locked cabinet. Observe all

warnings on container labels to avoid injury.

SafeyIructions

■ Keep the floor around your appliances clean and

dry to reduce the possibility of slipping.

■ Never climb on or stand on the dryer top.

■ Close supervision is necessary if this appliance is

used by or near children. Do not allow children to

play on, with, or inside this or any other appliance

WHEN USING YOUR DRYER

■ Never reach into the dryer while the drum is

moving. Before loading, unloading or adding

clothes, wait until the drum has completely

stopped.

■ The laundry process can reduce the flame

retardancy of fabrics. To avoid such a result,

carefully follow the garment manufacturer’s

care instructions.

■ Clean the lint filter before each load to prevent

lint accumulation inside the dryer or in the room.

DO NOT OPERATE THE DRYER WITHOUT THE LINT

FILTER IN PLACE.

■ Do not dry articles containing rubber, plastic,

or similar materials such as padded bras, tennis

shoes, galoshes, bath mats, rugs, bibs, baby pants,

plastic bags, pillows, etc. that may melt or burn.

Some rubber materials, when heated, can under

certain circumstances produce fire by

OpeagIructions

■ Do not wash or dry articles that have been

cleaned in, washed in, soaked in, or spotted

with combustible or explosive substances (such as

wax, oil, paint, gasoline, degreasers, dry-cleaning

solvents, kerosene, etc.) which may ignite or

explode. Do not add these substances to the

wash water. Do not use or place these substances

around your washer or dryer during operation.

spontaneous combustion.

■ Do not store plastic, paper or clothing that may

burn or melt on top of the dryer during operation.

ips

■ Garments labeled Dry Away from Heat or Do

Not Tumble Dry (such as life jackets containing

Kapok) must not be put in your dryer.

■ Do not place items exposed to cooking oils in

your dryer. Items contaminated with cooking oils

may contribute to a chemcial reaction that could

■ Do not dry fiberglass articles in your dryer.

Skin irritation could result from the remaining

particles that may be picked up by clothing

during subsequent dryer uses.

cause a clothes load to catch fire

rubleshotingT

■ Any article on which you have used a cleaning

solvent or that contains flammable materials

(such as cleaning cloths, mops, towels used in

beauty salons, restaurants, or barber shops, etc.)

must not be placed in or near the dryer until

solvents or flammable materials have been

removed. There are many highly flammable

items used in homes such as acetone, denatured

alcohol, gasoline, kerosene, some household

cleaners, some spot removers, turpentines,

waxes, wax removers and products containing

petroleum distillates.

■ To minimize the possibility of electric shock,

unplug this appliance from the power supply

or disconnect the dryer at the household

distribution panel by removing the fuse or

switching off the circuit breaker before

attempting any maintenance or cleaning

(except the removal and cleaning of the lint

filter). NOTE: Turning the Cycle Selector knob

to an OFF position does NOT disconnect the

appliance from the power supply.

CustomSrvice

SafeyIructions

■ Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled,

or has missing or broken parts, including a

damaged cord or plug.

■ You may wish to soften your laundered fabrics

or reduce the static electricity in them, by using

a dryer-applied fabric softener or an anti-static

conditioner. We recommend you use either a

fabric softener in the wash cycle, according to

the manufacturer’s instructions for those

products, or try a dryer-added product for

which the manufacturer gives written assurance

on the package that their product can be safely

used in your dryer. Service or performance

problems caused by use of these products are

the responsibility of the manufacturers of those

products and are not covered under the warranty

to this appliance.

■ The interior of the machine and the exhaust duct

connection inside the dryer should be cleaned at

least once a year by a qualified technician. See the

Loading and Using the Dryer section.

■ If yours is a gas dryer, it is equipped with an

automatic electric ignition and does not have a

pilot light. DO NOT ATTEMPT TO LIGHT WITH A

MATCH. Burns may result from having your hand

in the vicinity of the burner when the automatic

ignition turns on.

OpeagIructions

WHEN NOT USING YOUR DRYER

■ Grasp the plug firmly when disconnecting this

appliance to avoid damage to the cord while

pulling. Place the cord away from traffic areas so

it will not be stepped on, tripped over or

subjected to damage.

■ Before discarding a dryer, or removing it from

service, remove the dryer door to prevent

children from hiding inside.

■ Do not tamper with controls.

■

Do not attempt to repair or replace any part of

this appliance or attempt any servicing unless

specifically recommended in this Owner’s Manual

or in published user-repair instructions that you

understand and have the skills to carry out.

rubleshotingT

Read and follow this Safety Information carefully.

SAVE THESE INSTRUCTIONS

ips

CustomSrvice

About the dryer control panel.

You can locate your model number on the label on the front of the dryer behind the door.

Throughout this manual, features and appearance may vary from your model.

Models Type 333

AUTO

COTTONS

AUTO

PERM

PRESS

TEMPERATURE

START

MORE DRY

LESS DRY

MEDIUM

LESS DRY

START

COOL

DOWN

REGULAR

FLUFF

SafeyIructions

MORE DRY

80 MIN

TIMED

DRY

Models Type 453

AUTOMATIC

COTTONS

AUTOMATIC

PERMANENT

PRESS

START

FABRIC CARE

MORE DRY

LESS DRY

START

LESS DRY

COOL

DOWN

PERM. PRESS

MED. HEAT

COTTONS

REG. HEAT

OpeagIructions

MORE DRY

KNITS

DELICATES

LOW HEAT

FLUFF

NO HEAT

80 MIN

DEWRINKLE

DAMP DRY

TIMED DRY

ips

Models Type 473 and 475

AUTOMATIC

COTTONS

AUTOMATIC

PERMANENT

PRESS

LESS DRY

COOL DOWN

EXTRA CARE

START

FABRIC CARE

EXTRA CARE

SIGNAL

MORE DRY

rubleshotingT

EXTRA CARE

START

MEDIUM

LESS DRY

PERM. PRESS

MED. HEAT

OFF

COTTONS

REG. HEAT

SET

LOUD

MORE DRY

KNITS

DELICATES

LOW HEAT

FLUFF

NO HEAT

80 MIN

DEWRINKLE

DAMP DRY

TIMED DRY

Optional Feature,

on some models

NOTE:

CustomSrvice

Drying times will vary according to the type of heat used (Electric, Natural or LP gas),

size of load, types of fabrics, wetness of clothes and condition of exhaust ducts.

SafeyIructions

Control Settings

IMPORTANT: Clean the lint filter each time you use the dryer.

Fabric Care for Models Type 453, 473 and 475

COTTONS For regular to heavy cottons.

REG. HEAT

PERM. PRESS For synthetics, blends, delicates and items labeled permanent press.

MED. HEAT

FLUFF For fluffing items without heat. Use the TIMED DRY cycle.

OpeagIructions

NO HEAT

KNITS For delicates, synthetics and items labeled tumble dry low.

DELICATES

LOW HEAT

Temperature for Models Type 333

REGULAR For regular to heavy cottons.

MEDIUM For synthetics, blends, delicates and items labeled permanent press.

FLUFF For fluffing items without heat. Use the TIMED DRY cycle.

Automatic cycles automatically determine fabric dryness. Select MORE DRY for heavier fabrics, LESS DRY for

lighter fabrics. Timed cycles run for a selected time.

Drying Cycles for Models Type 453, 473 and 475

AUTOMATIC For cottons and most linens. For most loads select the Preferred Regular Setting marked with an

∗

rubleshotingT

COTTONS

AUTOMATIC For synthetic blends and delicates.

PERMANENT

PRESS

TIMED DRY Set the Cycle Selector at the desired drying time.

DAMP DRY For leaving items partially dry.

ips

DEWRINKLE For removing wrinkles from items that are clean and dry or that are very lightly damp.

Drying Cycles for Models Type 333

AUTO For cottons and most linens. For most loads select the Preferred Regular Setting marked with an

COTTONS

∗

AUTO PERM For synthetic blends and delicates.

PRESS

CustomSrvice

TIMED DRY Set the Cycle Selector at the desired drying time.

Start— Close the dryer door. Select START. Opening the door during operation will stop the dryer. To

restart the dryer, close the door and select START to complete the cycle.

About your dryer features.

Extra Care—On some models

EXTRA CARE

Use this option to minimize the wrinkles

in clothes. It provides approximately 15

minutes of no-heat tumbling after the

clothes are dry.

If you have a Cycle Signal knob and you

select the EXTRA CARE option, a signal will

sound at the end of the drying time and

several times during the EXTRA CARE cycle.

This will remind you that it is time to

remove the clothes.

OFF

SET

This option can only be used with the

Automatic cycles.

SafeyIructions

Cycle Signal—On some models

SIGNAL

This signal will sound just before the end

of the cycle to remind you to remove the

clothes. On some models the signal sound

level cannot be adjusted.

NOTE:

MEDIUM

■ Remove garments promptly at the sound

of the signal. Place clothes on hangers

so wrinkles won’t set in.

LOUD

OFF

If you selected the EXTRA CARE option the

signal will sound at the end of the drying

time and will sound several times during

the EXTRA CARE cycle. This will remind

you that it is time to remove the clothes.

■ Use the Cycle Signal especially when

drying fabrics like polyester knits and

permanent press. These fabrics should

be removed so wrinkles won’t set in.

OpeagIructions

Drum Lamp—On some models

Before replacing the light bulb, be sure to

unplug the dryer power cord or disconnect

the dryer at the household distribution

panel by removing the fuse or switching

off the circuit breaker. Reach above dryer

opening from inside the drum. Remove the

bulb and replace with the same size bulb.

ips

Drying Rack—On some models

A handy drying rack may be used for drying

articles such as stuffed toys, pillows or

washable sweaters.

NOTE:

rubleshotingT

■ The drying rack must be used with the

TIMED CYCLE.

Hook the rack over the lint filter so the rack

extends into the dryer drum.

■ Do not use this drying rack when there

are other clothes in the dryer.

SensorDry—On some models

This feature is only activated in the

automatic cycles.

As the clothes tumble they touch a large

sensor. The SensorDry feature will stop the

heating cycle as soon as the clothes have

reached the selected dryness.

SensorDry

CustomSrvice

About the reversing the door.

SafeyIructions

Reversing the Door

Tools needed:

■Standard #2

Phillips screwdriver putty knife

■Tape-tipped ■ Needle-nosed

pliers

Open the door and remove the filler plugs opposite the hinges. With the door

completely open, remove the bottom screw from each hinge on the dryer face. Insert

these screws about half way into the TOP holes, for each hinge, on the opposite side

(where you removed the filler plugs). Apply firm pressure to get the screw started in

untapped holes.

OpeagIructions

Loosen top screw from each hinge on the dryer face half way. With one hand holding

the top of the door and the other hand holding the bottom, remove the door from the

dryer by lifting it UP and OUT.

Rotate the door 180°. Insert it on the opposite side of the opening by moving the door

IN and DOWN until the top hinge and the bottom hinge are resting on the top screws

inserted in step 1.

rubleshotingT

Remove the remaining screws from the side of the opening from which the door was

removed. With these screws secure each hinge at the bottom. Tighten the two top

screws of each hinge. Reinsert the plastic plugs on the side from which the door was

removed.

ips

CustomSrvice

Loading and using the dryer.

Always follow the fabric manufacturer’s care label when laundering.

Sorting and Loading Hints

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains.

Bounce^®Fabric Conditioner Dryer Sheets have been approved for use in all GE Dryers when used in accordance

with the manufacturer’s instructions.

SafeyIructions

Do not overload. This wastes energy and causes wrinkling.

Do not dry the following items: fiberglass items, woolens, rubber-coated items, plastics, items with plastic trim and

foam-filled items.

Care and Cleaning of the Dryer

The Exterior: Wipe or dust any spills or washing

compounds with a damp cloth. Dryer control

panel and finishes may be damaged by some

laundry pretreatment soil and stain remover

products. Apply these products away from the

dryer. The fabric may then be washed and dried

normally. Damage to your dryer caused by these

products is not covered by your warranty.

The Exhaust Duct: Inspect and clean the exhaust

ducting at least once a year to prevent clogging.

A partially clogged exhaust can lengthen the

drying time.

Follow these steps:

Turn off electrical supply by disconnecting the

plug from the wall socket.

OpeagIructions

The Lint Filter: Clean the lint filter before each

use. Moisten your fingers and reach into the filter

opening. Run your fingers across the filter. Have a

qualified technician vacuum the lint from the dryer

once a year.

2 ^{Disconnect the duct from the dryer.}

Vacuum the duct with the hose attachment and

reconnect the duct.

The Exhaust Hood: Check with a mirror that the inside

flaps of the hood move freely when operating. Make

sure that there is not wildlife (birds, insects, etc.)

nesting inside the duct or hood.

ips

rubleshotingT

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

DRY LABELS

WASH LABELS

Tumble

dry

Machine

wash

cycle

Do not dry

(used with

do not wash)

Dry

Normal

Permanent Press/

wrinkle resistant

Gentle/

delicate

Permanent Press/

wrinkle resistant

Do not wash

Do not wring

Do not tumble dry

Gentle/

delicate

Hand wash

Water

temperature

Heat

setting

Hot

(50°C/120°F)

Warm

(40°C/105°F)

Cold/cool

(30°C/85°F)

High

Medium

Low

No heat/air

BLEACH LABELS

Special

instructions

Dry flat

Line dry/

hang to dry

In the shade

Drip dry

Bleach

CustomSrvice

symbols

Any bleach

Do not bleach

Only non-chlorine bleach

(when needed)

SafeyIructions

Venting the Dryer

For the best drying performance the dryer needs to be properly vented. The dryer will use more energy

and run longer if it is not vented to the below specifications. Carefully follow the details on Exhausting in

the Installation Instructions.

■ Use only rigid metal or flexible metal 4″ diameter

ductwork inside the dryer cabinet or for exhausting

to the outside.

■ Do not use plastic or other combustible ductwork.

■ Use the shortest length possible.

OpeagIructions

■ Do not crush or collapse.

■ Avoid resting the duct on sharp objects.

■ Venting must conform to local building codes.

Correct

Venting

rubleshotingT

Incorrect

Venting

ips

CustomSrvice

Before you call for service…

Troubleshooting Tips

Save time and money! Review the charts on the following

pages first and you may not need to call for service.

Problem

Possible Causes

What To Do

Dryer doesn’t start

Dryer is unplugged

• Make sure the dryer plug is pushed completely into

the outlet.

SafeyIructions

Fuse is blown/circuit breaker is • Check the house fuse/circuit breaker box and

tripped

replace fuse or reset breaker. NOTE: Most electric

dryers use two fuses/breakers.

Dryer doesn’t heat

Fuse is blown/circuit breaker is • Check the house fuse/circuit breaker box and

tripped, the dryer may tumble

but not heat

replace fuse or reset breaker.

Gas service is off

• Make sure gas shutoff at dryer and main shutoff are

fully open.

Dryer shakes or makes

noise

Some shaking/noise is normal.

Dryer may be sitting unevenly

• Move dryer to an even floor space, or adjust

leveling legs as necessary until even.

Greasy spots on clothes

Improper use of fabric softener • Follow directions on fabric softener package.

Drying dirty items with clean ones • Use your dryer to dry only clean items. Dirty items can

stain clean items and the dryer.

OpeagIructions

Clothes were not completely clean • Sometimes stains which cannot be seen when the

clothes are wet appear after drying. Use proper

washing procedures before drying.

Lint on clothes

Lint filter is full

• Clean lint screen before each load.

Improper sorting

• Sort lint producers (like chenille) from lint collectors

(like corduroy).

ips

Static electricity can attract lint

Overloading

• See suggestions in this section under STATIC.

• Separate large loads into smaller ones.

Paper, tissue, etc. left in pockets • Empty all pockets before laundering clothes.

Static occurs

Inconsistent drying times

No fabric softener was used

• Try a fabric softener.

• Bounce® Fabric Conditioner Dryer Sheets have been

approved for use in all GE Dryers when used in

accordance with the manufacturer’s instructions.

rubleshotingT

Overdrying

• Try a fabric softener.

• Adjust controls for less drying.

Synthetics, permanent press and • Try a fabric softener.

blends can cause static

Type of heat

• Automatic drying times will vary according to the type

of heat used (electric, natural or LP gas), size of load,

types of fabrics, wetness of clothes and condition of

exhaust ducts.

CustomSrvice

SafeyIructions

Problem

Possible Causes

What To Do

Clothes take too long

to dry

Improper sorting

• Separate heavy items from lightweight items (generally,

a well-sorted washer load is a well-sorted dryer load).

Large loads of heavy fabrics (like • Large, heavy fabrics contain more moisture and take

beach towels)

longer to dry. Separate large, heavy fabrics into smaller

loads to speed drying time.

Controls improperly set

Lint filter is full

• Match control settings to the load you are drying.

• Clean lint filter before every load.

OpeagIructions

Improper or obstructed ducting • Check installation instructions for proper

ducting/venting.

• Make sure ducting is clean, free of kinks and

unobstructed.

• Check to see if outside wall damper operates easily.

• Check the Installation Instructions to make sure the dryer

venting is correct.

Blown fuses or tripped circuit

breaker

• Replace fuses or reset circuit breakers. Since most

dryers use 2 fuses/breakers, make sure both are

operating.

Overloading/combining loads

Underloading

• Do not put more than one washer load in the dryer at

a time.

• If you are drying only one or two items, add a few items to

ensure proper tumbling.

rubleshotingT

Clothes are wrinkled

Clothes shrink

Overdrying

• Select a shorter drying time.

• Remove items while they still hold a slight amount of

moisture.

Letting items sit in dryer after

cycle ends

• Remove items when cycle ends and fold or hang

immediately.

Some fabrics will naturally shrink • To avoid shrinkage, follow garment care labels exactly.

ips

when washed. Others can be

• Some items may be pressed back into shape after drying.

safely washed, but will shrink

• If you are concerned about shrinkage in a particular item,

do not machine wash or tumble dry it.

in the dryer

CustomSrvice

Notes

SafeyIructions

OpeagIructions

ips

rubleshotingT

CustomSrvice

GE Dryer Warranty (For customers in the U.S.)

SafeyIructions

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care^®technician. For service,

call 800-GE-CARES.

For The Period Of:

GE Will Replace:

One Year

From the date of the

original purchase

Any part of the dryer which fails due to a defect in materials or workmanship. During this full

one-year warranty, GE will also provide, free of charge, all labor and in-home service to replace the

defective part.

Five Years

From the date of the

original purchase

Any extra large or super capacity dryer drum which fails due to a defect in materials or workmanship.

During this five-year limited warranty, you will be responsible for any labor or in-home service costs.

OpeagIructions

What GE Will Not Cover:

■Service trips to your home to teach you how to use the

product.

■Replacement of house fuses or resetting of circuit

breakers.

■Improper installation.

■Damage to the product caused by accident, fire, floods or

acts of God.

■Failure of the product if it is abused, misused, or used for

other than the intended purpose or used commercially.

■Incidental or consequential damage to personal property

caused by possible defects with this appliance.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your

legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

rubleshotingT

ips

Warrantor: General Electric Company. Louisville, KY 40225

CustomSrvice

Service Telephone Numbers.

GE Answer Center^®^{In the U.S.: 800.626.2000}

The GE Answer Center® is open 24 hours a day, 7 days a week.

In Canada, contact: Manager, Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310,

Moncton, N.B., E1C 9M3.

SafeyIructions

In-Home Repair Service In the U.S.: 800-432-2737

Expert GE repair service is only a phone call away.

In Canada, call 1-800-361-3400.

Special Needs Service In the U.S.: 800.626.2000

GE offers, free of charge, a brochure to assist in planning a barrier-free kitchen for persons

with limited mobility. In the U.S., call 800-TDD-GEAC (800-833-4322).

In Canada, contact: Manager, Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310,

Moncton, N.B., E1C 9M3.

OpeagIructions

Service Contracts In the U.S.: 800-626-2224

Purchase a GE service contract while your warranty is still in effect and you’ll receive a

substantial discount. GE Consumer Service will still be there after your warranty expires.

In Canada, call 1-800-461-3636.

ips

Parts and Accessories In the U.S.: 800-626-2002

Individuals qualified to service their own appliances can have parts or accessories sent directly

to their homes (VISA, MasterCard and Discover cards are accepted).

Instructions contained in this manual cover procedures to be performed by any user. Other servicing

generally should be referred to qualified service personnel. Caution must be exercised, since

improper servicing may cause unsafe operation.

rubleshotingT

Please consult your yellow pages for your local Camco number.

Service Satisfaction

If you are not satisfied with the service you receive from GE:

First, contact the people who serviced your appliance.

Next, if you are still not pleased, in the U.S., write all the details—including your phone number—to:

Manager, Customer Relations, GE Appliances, Appliance Park, Louisville, KY 40225; or,

in Canada, to Director, Consumer Relations, Camco Inc., 1 Factory Lane, Suite 310, Moncton, N.B.,

E1C 9M3.

CustomSrvice

Printed in Canada

EarthQuake Chipper 1692210 User Manual
Edelbrock Automobile Parts Torker II 440 User Manual
Festool Saw PD561593 User Manual
Fiesta Gas Grill EZT40050 P317 User Manual
Franke Consumer Products Ventilation Hood FMY 367 User Manual
Frigidaire Oven FGEW3045K F W B User Manual
Furuno Network Router FELCOM 250 User Manual
GE DVR Digital Video Multiplexer Recorder User Manual
GE Monogram Freezer ZIF360NXLH User Manual
GE TV Cables JGSP48SH User Manual