BATTERY DRIVE, FTP-604 Series
4” TYPE MECHANISM AND INTERFACE BOARD
FTP-644MCL001/002/FTP-624DCL/DSL
■ OVERVIEW
FTP-644MCL/FTP-624DCL/DSL Series is a high speed line
thermal printer driven by battery, printing on 4-inch wide paper
(112 mm/ 114 mm).
The printer is compact and lightweight, and the design allows
easy head maintenance, head cleaning and head replacement.
This printer is suitable for a variety of applications, such as hand
held terminals, POS terminals, ticket machines, coupon
machines, label printers, etc.
FTP-644MCL001
■ HIGHLIGHTS
• High speed printing
It can print at 50 mm/s (400 dotlines/s) maximum by using
Fujitsu Components' unique head drive control.
• Compact and lightweight
The printer has a low profile of only 20 mm, and a light weight
of approximately 125 g.
• Low power consumption
The peak current for head drive is only 3.5 A (8.5VDC, 128
dots on).
FTP-624CU102
• Easy head access
It is designed for easy head cleaning and head replacement.
• Paper auto loading function
Thermal paper can be loaded without head-up lever
operation.
• UL recognized
File No. E171434
FTP-624DCL/DSL002
1
FTP-644MCL001/002/FTP-624DCL/DSL002
(Continued)
Item
For head
Specifications
Voltage: 4.2 to 8.5 VDC (equivalent to 2 Lithium lon batteries)
Peak current: approx. 3.5 A (conditions: room temp., 7.2VDC, 128 dots on)
Power
supply
Voltage: 4.2 to 8.5 VDC (equivalent to 2 Lithium lon batteries)
Peak current: approx. 0.8 A (conditions: room temp., 7.2 VDC)
For motor
For logic
Voltage: 5 VDC ± 5%
Current: 0.2 A maximum
Mechanism
138 (W) × 46 (D) × 20 (H) mm (excluding lever and knob diameter)
131 (W) × 89(D) × 24 (H) mm
Dimensions
Interface board
Weight (Mechanism)
approximately 125 g
Expected life
Mechanism
Pulse durability: 1 × 108 pulse/dot (using Fujitsu Takamisawa's standard
driving method)
Wear resistance: 50 km (at 12.5% print ratio)
Operating temperature
0 to +50°C*2
Environmental
conditions
Operating humidity
Storage temperature
Storage humidity
Head temperature
Paper out/Mark detect
Head-up
20 to 85% RH (no condensation)
–20 to +60°C
5 to 95% RH (no condensation)
By thermistor (applied energy control, abnormal temperature detection)
By photointerrupter
Detection
By microswitch
For front insertion use (112 mm width) : FTP-040PU001, FTP-040PG021
For rear insertion use (114 mm width) : FTP-040P0020, FTP-040PG106
In Europe (112 mm width)
· Oji Paper
· NIPPON Paper
· MITSUBISHI Paper Mills
:FTP-041P0060-45
Recommended thermal sensitive paper
: PD160R, PD170R, PD150R
: TF50KS-E4, TF60KS-E,TF50KS-E
: P220VBB-1, AFP-235
*1: There may be exceptions.
*2: Guarantee +5°C to +40°C.
3
FTP-644MCL001/002/FTP-624DCL/DSL002
■ DIMENSIONS
Printer mechanism
PAPER INSERTION
(MCLOO1)
20.1
HEAD UP LEVER (AT HEAD DOWN)
CENTER OF PAPER
PAPER INSERTION
(MCLOO2)
HEAD CONNECTOR
65.7
71.8±1
(137.5)
Unit: mm
4
FTP-644MCL001/002/FTP-624DCL/DSL002
Interface board
130.8
120.7
105.4
71.1
33.0
5.1
5.1
15.2
CN5
CN12
CN9
CN10
CN11
59.7
CN2
CN1
CN4
5.1
5.1
73.7
4-03.6
86.4
105.4
114.2
120.7
Mounting Height
Mounting Height
* CN9 on FTP-624DSL only
Unit: mm
** CN8, CN11, CN12 not used
■ FUNCTION
ITEM
ITEM
1.
2.
3.
4.
5.
6.
7.
Test printing
8.
9.
Motor power save
Mark detection
Paper-out detection
Paper near end detection
Head-up detection
10.
11.
12.
13.
MCU trouble detection
Power on/off sequence protection
Motor protection
Abnormal temp. of thermal head detection
Blown fuse detection
Hardware timer
Abnormal voltage detection of head
5
FTP-644MCL001/002/FTP-624DCL/DSL002
■ CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM
1. Thermal Head
Head side 1 : B11B-PH-K-S-2.2 (J.S.T.) or equivalent
2: B10B-PH-K-S-2.2 (J.S.T.) or equivalent
Board side 1: PHR-11 (J.S.T.) or equivalent
2: PHR-12 (J.S.T.) or equivalent
Connector Thermal Head 1
No. Signal Comment
Connector Thermal Head 2
No. Signal Comment
1
2
STB5 Print enable signal 5
STB6 Print enable signal 6
STB7 Print enable signal 7
STB8 Print enable signal 8
1
2
VH
VH
Power for head
Power for head
3
3
GND Head ground
GND Head ground
4
4
5
CLK
LAT
DIN
Data transmission clock
Print data latching signal
Print data output signal
5
TH*1
Temperature detection
6
6
STB1 Print enable signal 1
STB2 Print enable signal 2
STB3 Print enable signal 3
STB4 Print enable signal 4
VDD Power for logic
7
7
8
GND Head ground
GND Head ground
8
9
9
10
11
VH
VH
Power for head
Power for head
10
*1: Symbol: " " means a negative logic signal
Thermal head heat sink
Head up level
Motor
1, 2, 3, ...............9, 10
1, 2, 3, ...............10, 11
Connector Pin No.
3. Sensor connectors
Sensor
: PHR-5 (J.S.T.) or equivalent
Board side : B5B-PH-K-S (J.S.T.) or equivalent
No. Signal Comment
No. Signal Comment
1
2
3
4
B
B
A
A
Stepping motor coil excitation
Stepping motor coil excitation
Stepping motor coil excitation
Stepping motor coil excitation
1
2
3
4
5
VSEN Power for paper sensor
PHE Photo interrupter emittor
PHK Photo interrupter cathode
SW1 Head up detect switch 1
SW2 Head up detect switch 2
6
FTP-644MCL001/002/FTP-624DCL/DSL002
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
7
|