Fujioh Ventilation Hood BUF 06E User Manual

1U03 1182  
Range Hood  
Model: BUF-06E INSTALLATION MANUAL  
NAMES OF PARTS  
CIRCUIT DIAGRAM  
SAFETY INSTRUCTIONS  
Before installation and operation, read these instructions carefully  
and use this product only in the manner described by the  
manufacturer in the operation manual.  
The instruction shown below are used to alert you to potential  
personal injury and property damage hazards.  
There are three hazard classifications based on potentially  
dangerous situations.  
Obey all safety instructions that show these symbols to avoid  
possible injury, death and property damage.  
4. TO REDUCE THE RISK OF FIRE, ELECTRIC  
SHOCK, OR INJURY TO PERSONS, OBSERVE  
THE FOLLOWING:  
a) Installation work and electrical wiring must be done  
by a qualified person(s) in accordance with all  
applicable codes and standards, including fire-rated  
construction.  
b) Sufficient air is needed for proper combustion and  
exhausting of gases through the flue (chimney) of  
fuel burning equipment to prevent back drafting.  
Follow the heating equipment manufacturer’s  
guidelines and safety standards such as those  
published by the National Fire Protection  
Association (NFPA), and The American Society for  
Heating, Refrigeration and Air Conditioning  
Engineers (ASHRAE), and the local code  
authorities.  
c) When cutting or drilling into wall or ceiling, do not  
damage electrical wiring and other hidden utilities.  
d) Ducted fans must always be vented to the outdoors.  
e) The end user is responsible to ensure compliance  
with all Federal, State and Local Environmental and  
Fire codes.  
Connector  
Lamp:50W  
Lamp  
(Not supplied)  
Front Cover  
ON  
OFF  
Black  
White  
Black  
White  
Enclosure  
Lamp Switch  
Switch (Lamp)  
Terminal  
Lamp  
(Not supplied)  
Connector  
Lamp:50W  
Black  
120V 60Hz  
Black  
Black  
White  
Green  
White  
White  
White Black  
WARNING indicates a potentially  
WARNING:  
hazardous situation which, if not  
avoided, could result in death or  
serious injury.  
Black  
White  
Terminal  
Connector  
Connector  
CAUTION: CAUTION indicates a potentially  
hazardous situation which, if not  
avoided, may result in minor or  
moderate injury.  
Filter  
CAUTION:  
CAUTION used without the safety  
alert symbol indicates a potentially  
hazardous situation which, if not  
avoided, may result in property  
damage.  
SIZE & DIMENSIONS  
ACCESSORIES  
5. TO REDUCE THE RISK OF FIRE, USE ONLY  
METAL DUCTWORK.  
NOTE: The safety instructions are explained with the following  
(Unit: inch)  
pictographic symbols.  
6. This unit must be grounded.  
9-13/16"  
Ø7/8"  
4-Ø1/4"  
Holes for mounting range hood  
7. Install this range hood to a liner. Check that the  
hood is correctly installed, since incorrect  
installation could result in the range hood becoming  
detached and falling off.  
means prohibition. It indicates actions, if any, that  
mustn’t be done.  
Screw M5×30  
Four (4) pieces  
Nut with plate  
Four (4) pieces  
means forcible execution. It indicates actions, if  
any, that must be done.  
8. Connect only to an AC120 Volt power source or  
the range hood could result in fire, electric shock,  
and damage.  
15-13/16"  
14-1/8"  
9/16"  
WARNING  
CAUTION  
6-3/4"  
RANGE HOOD LOCATION  
The range hood must be in-  
stalled just above the cooktop.  
26"  
1. For general ventilating use only. Do not use to  
exhaust hazardous or explosive material and  
vapors.  
1. TO REDUCE THE RISK OF FIRE, ELECTRIC  
SHOCK, OR INJURY TO PERSONS, OBSERVE  
THE FOLLOWING:  
a) Use this unit only in the manner intended by the  
manufacturer. If you have questions, contact the  
manufacturer.  
b) Before servicing or cleaning unit, switch power  
off at service panel and lock the service  
disconnecting means to prevent power from being  
switched on accidentally. When the service  
disconnecting means cannot be locked, securely  
fasten a prominent warning device, such as a tag,  
to the service panel.  
25-1/16"  
23-3/8"  
Ø9-15/16"  
1
2
2. To reduce the risk of fire and to properly exhaust  
air, be sure to duct air outside. Do not vent exhaust  
air into spaces within walls or ceilings or into attics,  
crawl spaces, or garages.  
The minimum distance from the  
cooking surface to the bottom  
of the range hood must be 24".  
Liner  
3. Read specification label on this product for further  
information and requirements.  
24" (Minimum)  
27"  
The total weight of the BUF-06E  
Cook top  
3
4
range hood unit is 11 lbs. (5 kg)  
4. Use only for the purpose of kitchen ventilation.  
Power requirements are:  
AC120 V, 60 Hz, 1.0 Amp  
2. To reduce the risk of fire or electric shock, do not  
use this product with any solid-state speed control  
device.  
5. Do not install this range hood in the bathroom or in  
other wet rooms since electrical shock and damage  
may result.  
3. Do not attempt to control Remote Blower using  
the internal switch provided on the front panel of  
the BUF-06E.  
6. Fasten the filter and other parts securely. Incorrect  
attachment may result in personal injury or property  
damage.  
WARNING:  
• Check that the hood is correctly installed, since incorrect  
installation could result in the detachment of the range hood  
and the unit could fall.  
THIS SWITCH IS TO BE USED FOR THE  
CONTROL OF THE LIGHTS ONLY!ASEPARATE  
SWITCH, WITH PROPERLY RATED  
AMPERAGE MUST BE INSTALLED TO  
CONTROL THE REMOTE BLOWER MOTOR.  
Contact the Remote Blower manufacturer or a  
Certified Electrician for their recommendations.  
7. Keep your hands and other objects away from the  
fan while it is in motion. The range hood may injure  
you or damage itself.  
CAUTION:  
• To protect hands from injury, wear working gloves when  
installing the range hood.  
8. To reduce the risk of fire and electric shock, install  
this range hood only with remote blower models  
rated maximum current of 12.8 amps.  
INSTALLATION  
1. Preparation  
2. Range Hood Mounting  
3. Connecting Power Supply Wires  
4. Final Assembly and Check  
Assembly  
CAUTION:  
• Wear working gloves to avoid injury.  
1
1) Remove the switch’s protective cardboard.  
WARNING:  
WARNING:  
To prevent air or moisture from entering through the wall opening,  
be sure to install wall insulation to seal around duct work completely.  
• If the range hood is not installed properly, it could become detached  
and fall.  
• Ensure that the metal duct does not touch other metal housing  
materials, otherwise fire or electric shock could result.  
• Electrical wiring should be done by a qualified person(s) in  
accordance with all applicable codes and standards, including  
fire-rated construction. An unqualified person doing the work could  
result in fire, electric shock or injury.  
• This range hood uses 120V AC. Do not connect to other voltage  
since fire, electric shock or damage could result.  
WARNING:  
Remove the protective cardboard without fail, otherwise there is  
a risk of fire.  
Detach the filters by loosening 2 screws. Then remove 5 screws  
fixing the front cover and detach the front cover.  
1
Cardboard  
Screw  
According to the conditions where the range hood is installed, de-  
Filter  
1
Remove the nut from the conduit  
connector at the end of power wiring.  
Front cover  
termine whether it will be discharged vertically or horizontally (10"  
Round duct). For vertical or horizontal discharge, run duct work be-  
tween the hood location and the exterior blower used with the range  
hood. For best result in either direction, use a minimum number of  
transitions and elbows. As for installing the exterior blower, please  
refer to its installation.  
1
Conduit  
(Not supplied)  
WARNING:  
Be sure to switch power OFF at  
service panel before wiring.  
Nut  
(Not supplied)  
Front cover  
Screw  
Loosen 2 screws  
Remove two  
to remove the filter.  
Cardboard  
2
screws fixing  
the wire cover  
and detach it.  
(Do not remove yet.)  
CAUTION:  
Do not remove the switch’s protective cardboard until proceeding to  
“4. Final Assembly and Check”.  
Filter  
Wire cover  
Screw  
Hold up the range hood and align the 4 screw holes of the liner and  
range hood, then fix securely using the supplied screws (M5×30)  
and nuts.  
2
2) Attach the front cover, and secure it with 5 screws.  
Then attach the filters.  
Note: Fasten all the screws and nuts evenly.  
3) Two 50 Watt halogen light bulbs (not supplied) can be mounted  
in this range hood.  
Connect the conduit through  
the connecting hole of the  
body using the nut previously  
removed.  
3
Liner  
Prior to function check, install light bulbs (PAR20 bulb, with  
base diameter 26 mm: medium base), rated 120 V - 50 Watt or  
below.  
The following light bulbs are recommended for this range hood.  
• GE Model No. 50PAR20H/FL25  
• SYLVANIA Model No. 50PAR20/HAL/DL/NFL  
Turn the lamps clock-wise to install them.  
Nut  
The range hood unit must be mounted to a liner which has the  
following dimensions. Install the liner securely after checking that  
the opening size of the liner is the same as the figure below.  
2
Conduit  
Liner Dimensions  
Bulb  
(Not supplied)  
Check  
(1) Turn on the electrical circuit  
to the range hood.  
2
Connect the electrical  
wires as follows:  
• Black to Black  
• White to White  
• Green to Green  
4
5
(2) Make sure that the switch  
and light operate correctly.  
Refer to page 5 of the  
Operation Manual.  
Screw-washer  
[Right & left, each  
two (2) places]  
Securing plate  
[Securing plate turns  
while passing through  
the opening of Liner]  
(3) Make sure that the range  
CAUTION:  
hood functions rightly and it  
has no abnormal noises  
and/or vibration.  
Push to turn ON  
Liner  
Connect wires tightly  
and securely using  
wire connectors  
• The liner shape illustrated in this installation manual is only for  
reference.  
Four screws (M5×30)  
Wire Connector  
(Not supplied)  
(not supplied).  
* As for operating the exterior blower used with this hood, please  
refer to its operation manual.  
CAUTION:  
Replace the wire  
• When the liner is installed in the wooden hood, the inside of the  
wooden hood placed above the cooking surface must be fully covered  
by the metal barrier including bottom edges. Select a suitable liner  
and metal barrier according to the size and shape of the wooden  
hood and install properly.  
Check that the top of the ex-  
haust port is inserted into the  
bottom of 10" round duct, then  
make the duct joint secure and  
air tight using non-flammable  
tape such as duct tape, etc.  
(not supplied)  
3
cover with the screws  
removed previously.  
Make sure that all  
wires are connected  
properly and enclosed  
inside of the wiring  
5. Explanation to the End User  
(1) Referring to the Operation Manual, explain the operation of this  
range hood to end users.  
(2) The Installation Manual and Operation Manual should be given to  
the end user.  
• The liner should be installed tightly. If the liner installation is not correct,  
the range hood unit may become detached and fall.  
Wire cover  
Screw  
compartment.  
Non-flammable tape  
 

Eclipse Fujitsu Ten GPS Receiver AVN4429 User Manual
Fellowes Indoor Furnishings RH 300 User Manual
Fisher Price Doll W1710 User Manual
Friedrich Air Cleaner C 90A User Manual
Frigidaire Washer FAFW3517A User Manual
Fujitsu Tablet FMW4503TS128A01 User Manual
Gateway Personal Computer E 4400 User Manual
GE Cooktop 164D3333P235 User Manual
GE Cordless Telephone 26920R User Manual
Generac Power Systems Portable Generator 0784 1 User Manual