Installation Manual
RANGE HOOD
MODEL:BUF-01
BUF-02
TABLE OF CONTENTS
Safety Instructions .................................................................................................. 2
Name of Parts ......................................................................................................... 4
Size & Dimensions .................................................................................................. 4
Range Hood Location ............................................................................................. 5
Installation ............................................................................................................... 6
1. Preparation ..................................................................................................... 6
2. Range Hood Mounting .................................................................................... 8
3. Connecting Power Supply Wires ................................................................... 10
4. Final Assembly and Check............................................................................ 12
5. Explanation to the End User ......................................................................... 13
Circuit Diagram ..................................................................................................... 13
READ AND SAVETHESE INSTRUCTIONS.
Keep this manual in a convenient place for future reference.
FUJI INDUSTRIAL CO., LTD.
1U030584
CAUTION
1. For general ventilating use only. Do not use to exhaust hazardous or explosive material and
vapors.
2. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent
exhaust air into spaces within walls, ceilings or into attics, crawl spaces or garages.
3. Read specification label on this product for further information and requirements.
4. Use only for the purpose of kitchen ventilation.
5. Do not install this range hood in the bathroom or in other wet rooms since electrical shock
and damage may result.
6. Fasten the filter and other parts securely. Incorrect attachment may result in personal injury
or property damage.
7. Keep your hands and other objects away from the fan while it is in motion.The range hood
may injure you or damage itself.
NOTE:The safety instructions are explained with the following
pictographic symbols.
: means prohibition. It indicates actions, if any, that
mustn’t be done.
: means forcible execution. It indicates actions, if any,
that must be done.
ꢀ
3
NAME OF PARTS
- Accessories -
Screw M5×30
Four (4) pieces
Nut with plate
Four (4) pieces
SIZE & DIMENSIONS
(Unit : inch)
4
RANGE HOOD LOCATION
The range hood must be installed just above the cooktop.
1
2
3
The minimum distance from the cooking surface to the bottom of the range hood
must be 24".
The total weight of the BUF-01/BUF-02 range hood unit is:
BUF-01/BUF-02 ----- 18 lbs. (8 kg)
Power requirements are:
4
BUF-01 AC120 V, 60 Hz, 1.3 Amp
BUF-02 AC120 V, 60 Hz, 2 Amp
CAUTION
• Check that the hood is correctly installed, since incorrect installation could result
in the detachment of the range hood and the unit fall.
• To protect hands from injury, wear working gloves when installing the range hood.
5
INSTALLATION
1. PREPARATION
WARNING
• If the range hood is not installed properly, it could become detached and fall.
• Ensure that the metal duct does not touch other metal housing materials,
otherwise fire or electric shock could result.
This range hood is designed to
discharge upward. For vertical discharge,
run duct work between the hood location
and roof cap location.
To get the best result, use a minimum
number of transitions and elbows. Be
sure to attach a roof cap to avoid leaking
rain in the end.
1
The range hood unit must be mounted to a liner which has the following
dimensions. Install the liner securely after checking that the opening size of the
liner is the same as the figure below.
2
CAUTION
The liner should be installed tightly. If the liner installation is not correct, the range
hood unit may become detached and fall.
6
INSTALLATION (continued)
Run house wiring between service panel and hood location.
Prepare the range hood unit.
3
4
(1) The range hood is supplied with the
exhaust pipe fixed on its top plate.
(2) Provide a transition duct (not
supplied) to connect the exhaust
pipe and external duct.The
diameter of the transition duct
should be more than 6".
(3) Be sure to keep 1-3/16" overlapping
length of the exhaust pipe and
transition duct.
7
INSTALLATION (continued)
2. RANGE HOOD MOUNTING
Hold up the range hood unit and insert it into the opening of the liner. When the 4
securing plates on both sides have passed through the top of the liner, turn them
outward to secure the range hood on the liner temporarily. Make sure that the top
of the exhaust pipe is inserted into the bottom of the transition duct.
1
8
INSTALLATION (continued)
Remove 4 screws which are fixed to the front cover. The front cover swings open
90° as shown in Fig.
2
CAUTION
Do not detach the front cover from the range hood unit.The hinge may be damaged.
Align 4 screw holes of the liner and range hood unit, then fix securely using the
supplied screws and nuts.
3
NOTE
Fasten all screws and nuts evenly.
Make the duct joint secure and air tight
using non-flammable tape such as duct
tape, etc. (not supplied)
4
NOTE
Make sure that the shutter installed in
the exhaust pipe moves freely.
9
INSTALLATION (continued)
3. CONNECTING POWER SUPPLY WIRES
WARNING
• Electrical wiring should be done by a qualified person(s) in accordance with all-
applicable codes and standards, including fire-rated construction. An unqualified
person doing the work could result in fire, electric shock or injury.
• This range hood uses 120V AC. Do not connect to other voltage since fire, electric
shock or damage could result.
Remove the nut from the conduit
connector at the end of power wiring.
1
WARNING
Be sure to switch power OFF at service panel
before wiring.
Remove one screw fixing the wire cover and
detach it.
2
Connect the conduit through the connecting hole
of the body using the nut previously removed.
3
10
INSTALLATION (continued)
Connect the electrical wires as follows:
Connect wires tightly and securely using wire connectors (not supplied).
4
5
• Black to Black
• White to White
• Green to Green
Replace the wire cover with the screw removed previously. Make sure that all
wires are connected properly and enclosed inside of the wiring compartment.
11
INSTALLATION (continued)
4. FINAL ASSEMBLY AND CHECK
One 40 W light bulb (not supplied) can be mounted to this range hood.
Prior to final assembly, install a light bulb (ordinary type, in the base diameter
17 mm: intermediate base), rated 120 V-40 W or below.
Assembly
Replace the front cover with 4 screws.
1
CAUTION
To prevent the screw holes from being damaged, be sure to tighten the screws with
the torque of 13 inch-lbs. (1.5 N-m) or less.
Check
(1) Turn on the electrical circuit to the range hood.
(2) Make sure that the switch and light operate correctly. Refer to page 4 of the
2
Operation Manual.
(3) Check the ventilating functions at Hi, Me and Lo positions.
(4) Make sure that the range hood has no abnormal noises and/or vibration.
CAUTION
• To reduce the risk of injury, keep your hands and other objects away from the fan
while it is in motion.
• Wear working gloves to avoid injury.
12
INSTALLATION (continued)
5. EXPLANATION TO THE END USER
(1) Refer to the Operation Manual, explain the operation of this range hood to end
users.
(2) The Installation Manual and Operation Manual should be given to the end user.
CIRCUIT DIAGRAM
120V 60Hz
Motor
Green
White Black
Connector
Terminal
Capacitor
Red
White
Orange
Brown
Blue
Red
Bulb:Max40W
Connector
Blue
Brown
Orange
White
Black
Green
Red
Control Switch
13
Fuji Industrial USA, Inc.
16300 Christensen Rd., Ste-212 Seattle,WA 98188-3403
Telephone: 1-888-547-9880
1U030584
|