INSTALLATION INSTRUCTIONS
Over The Range Microwave Oven
BEFORE YOU BEGIN
Read these instructions completely and carefully.
IMPORTANT
inspector’s use.
•
•
•
•
Save these instructions for local
•
•
Proper installation is the responsibility of the installer.
Product failure due to improper installation is not covered
under the Warranty.
IMPORTANT
coordinates.
Observe all governing codes and
•
•
Please read all instructions thoroughly before installing
the Over the Range Microwave Oven. Two people are
recommended to install this product.
NOTE TO INSTALLER – Be sure to leave these
instructions with the Consumer.
If a new electrical outlet is required, its installation should be
completed by a qualified electrician before the Microwave
Oven is installed. See 3 ELECTRICAL GROUNDING
INSTRUCTIONS on page 2.
NOTE TO CONSUMER – Keep these instructions for
future reference.
• SKILL LEVEL – Installation of this appliance requires
basic mechanical and electrical skills.
2 WALL CONSTRUCTION
1 MOUNTING SPACE
This Microwave Oven/Hood should be mounted against and
supported by a flat vertical wall. The wall must be flat for
proper installation. If the wall is not flat, use spacers to fill in
the gaps. Wall construction should be a minimum of 2" x 4"
wood studding and ³⁄₈" or more thick dry wall or plaster/lath.
The mounting surfaces must be capable of supporting weight
of 110 pounds—the oven and contents—AND the weight of
all items which would normally be stored in the top cabinet
above the unit.
This Microwave Oven/Hood requires a mounting space on
a wall as shown in Figure 1. It is designed to be used with
standard 12" wall cabinets.
12"
30"
15.5"
The unit should be attached to a minimum of one 2" x 4"
wall stud or two 2" x 3" wall studs.
30" or more
from cooking
surface
At least 2"
Backsplash
To find the location of the studs, one of the following methods
may be used:
A. Use a stud finder, a magnetic device which locates the
nails in the stud.
B. Use a hammer to tap lightly across the mounting surface
to find a solid sound. This will indicate stud location.
The center of the stud can be located by probing the wall with
a small nail to find the edges of the stud and then placing a
mark halfway between the edges. The center of any adjacent
studs will normally be 16" or 24" to either side of this mark.
66" or more
from floor
NEED HELP?
For customers in the United States, call: 1-800-944-9044
Figure 1
For customers in Canada, call: 1-800-213-9397 (English)
1-800-668-4606 ext.8199 (French)
READ CAREFULLY. KEEP THESE INSTRUCTIONS.
P/N 316137234
TINSEB151WRRZ
Printed in Thailand
INSTALLATION INSTRUCTIONS
5 TOOLS RECOMMENDED FOR
INSTALLATION
7 PREPARATION OF THE OVEN
1. Open the bottom of the carton, bend the carton flaps back
andtilttheovenovertorestonplasticfoampad. Liftcarton
off oven and remove all packing materials, Installation
Instructions, Wall Template, Top Template, Charcoal
Filter, Turntable and Turntable Support; however, DO
NOT REMOVE THE WAVEGUIDE COVER, which is
located on the ceiling in the oven cavity. SAVE THE
CARTON AS IT MAY MAKE INSTALLATION EASIER.
•
•
•
•
Phillips Screwdriver
Electric Drill
¹⁄₂", ⁵⁄₈" and ³⁄₃₂" Drill Bits
1 ¹⁄₂" Wood Bit or Metal Hole Cutter
(if metal cabinet is used)
•
•
Saw to cut exhaust opening (if needed)
2. CHECK THE OVEN.
Protective Drop Cloth for product and range -
you may also use carton for protection
Check the oven for any damage, such as misaligned or
bent door, damaged door seals and sealing surfaces,
broken or loose door hinges and latches and dents inside
the cavity or on the door. If there is any damage, do not
operate the oven and contact your dealer or Electrolux
AUTHORIZED SERVICER.
•
•
•
•
Scissors
Pencil
Measure
Tape
6 INSTALLATION HARDWARE
The INSTALLATION HARDWARE (items 1 - 7 ) packed with
the oven should contain the following:
Mounting Plate
Item
Name
Quantity
1
Wood Screw 5 x 35 mm
Toggle Bolt ³⁄₁₆"
6
4
2
2
1
4
1
2
Figure 5
2
3
4
5
6
7
8
Top Cabinet Screw 5 x 85 mm
Flat Washer 30 mm diameter
Grommet
Tapping Screw 4 x 8 mm
Exhaust Damper Assembly
Grease Filter
Figure 4
Parts shown not to common scale.
E3
INSTALLATION INSTRUCTIONS
(B)HORIZONTAL EXHAUST: OUTSIDE VENTILATION
8 VENTILATION SYSTEM
(PREPARING OVEN FOR INSTALLATION)
1. Remove and save 2 screws from back edge and 1 screw
from the top center of Fan Cover Bracket. Remove Fan
Cover Bracket by sliding it in the opposite direction of the
arrow on the Fan Cover Bracket, as shown in Figure 7.
This microwave oven/hood is designed for adaptation to three
types of hood ventilation systems. Select the type required
for your installation.
2. Withdraw Hood Fan Unit carefully and slip wires out of
Wire Box. See Figure 8.
RECIRCULATING — non-vented, ductless.
Follow installation procedure (A). Recirculating requires
the use of the Charcoal Filter, which has already been
installed in the oven.
CAUTION: Do not pull or stretch hood fan wiring.
3. Rotate the Hood Fan Unit and turn end-over-end so that
the fan blade openings are facing the back of the oven.
Replace Hood Fan Unit into the oven. Be careful not to
pinch the lead wire between the inner bracket and the
Hood Fan Unit. See Figure 9.
HORIZONTAL EXHAUST — outside ventilation.
Follow installation procedure (B).
VERTICAL EXHAUST — outside ventilation.
Follow installation procedure (C).
4. Put the lead wire into Wire Box. See Figure 10.
(A) RECIRCULATING: NON-VENTED, DUCTLESS OPERATION
1. The unit is shipped assembled for recirculating.
5. Replace the Fan Cover Bracket by sliding it into the slits
in the same direction as the arrow on the Fan Cover
Bracket. Make sure the fan blades are visible through
the rear openings in the oven before proceeding. Attach
Fan Cover Bracket to unit with 3 screws, which were
removed in Step 1 above. See Figure 11. The Hood Fan
Unit is now rotated for horizontal exhaust operation.
2. The Exhaust Damper Assembly is not required for
recirculating exhaust.
3. Charcoal Filter, included with the unit, is required for
recirculating exhaust. Attach the Charcoal Filter to the
upper side of the oven by sliding into the tabs. See
Figure 6. The Charcoal Filter should be replaced every 6
to 12 months, depending on use.
6. Attach the Exhaust Damper Assembly to the back of the
unit. See Figure 10. Use two Tapping Screws 4 x 8 from
the INSTALLATION HARDWARE and tighten into place.
Tabs
Tabs
Figure 8
Figure 6
Fan Cover Bracket
Back of
Oven
Figure 7
Figure 9
E4
INSTALLATION INSTRUCTIONS
Fan Cover Bracket
Rotate 90°
Figure 11
Exhaust Damper
Assembly
9 OVEN INSTALLATION
THIS OVEN CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING
TO THE MOUNTING INSTRUCTIONS FOUND ON BOTH TEMPLATES.
Tapping Screw
THE NEXT STEP IS TO READ AND FOLLOW MOUNTING INFORMATION
ON BOTH TOP CABINET AND WALL TEMPLATES.
Figure 10
NOTE: THIS OVEN SHOULD BE ATTACHED TO AT LEAST ONE WALL
STUD.
8 VENTILATION SYSTEM
MOUNTING PLATE
(PREPARING OVEN FOR INSTALLATION)
1. Separate 4 Toggle Bolts, packed in the INSTALLATION
HARDWARE, from the Toggle Nuts.
(C) VERTICAL EXHAUST: OUTSIDE VENTILATION
IMPORTANT
2.
Use the mounting template
provided to Use wood screws to attach mounting
plate to the stud or studs. Use Toggle Bolts to attach
mounting plate through the holes UNLESS THOSE
HOLES ARE LOCATED ON THE STUD. Insert one
Toggle Bolt where appropriate (these correspond
to holes of the Wall
1. Remove and save 2 screws from back edge and 1 screw
from the top center of the Fan Cover Bracket. Remove
Fan Cover Bracket by sliding it in the opposite direction
of the arrow on the Fan Cover Bracket as shown in
Figure 7.
2. Withdraw Hood Fan Unit carefully and slip wires out of
Wire Box. See Figure 8.
CAUTION: Do not pull or stretch hood fan wiring.
Template) and put the
Toggle Nuts onto the
Toggle Bolts. Figure 13.
Refer to instructions in
Wall Template.
3. Turn the Hood Fan Unit end-over-end. Rotate the Hood
Fan Unit 90˚ so that the fan blade openings are facing
upward. Replace Hood Fan Unit into the oven. Be careful
not to pinch the lead wire between the inner bracket and
the Hood Fan Unit. See Figure 11.
3. Position the Mounting Plate with the Toggle Bolts
attached at the wall location and insert Toggle Nuts
and Bolts through the holes in the wall with the Toggle
Nuts closed. Figure 15. Use Wood Screws to attach the
Mounting Plate to studs.
4. Put the lead wire into Wire Box. See Figure 11.
5. Replace the Fan Cover Bracket by sliding it into the slits
in the same direction as the arrow on the Fan Cover
Bracket. Make sure the fan blades are visible through
the top openings in the oven before proceeding. Attach
the Fan Cover Bracket to unit with 3 screws, which were
removed in Step 1 above. See Figure 10. The Hood Fan
Unit is now rotated for vertical exhaust operation.
NOTE: Before insertion, be sure you leave a space more
than the thickness of the wall between the Mounting Plate
and the end of each of the Toggle Nuts (in the closed
position). If you do not leave enough space, the Toggle
Nut will not be able to open on the other side of the wall.
Also, once a Toggle Nut opens, it cannot be withdrawn
from the hole; therefore make sure all of the Toggles are
in the correct position before insertion.
6. Attach the Exhaust Damper Assembly to the fan cover
bracket on the top of the outercase cabinet after mounting
the oven. To attach the Exhaust Damper Assembly, refer
to MOUNTING OVEN TO THE WALL, page 6 Figure 17.
4. Align the Mounting Plate carefully and hold in position
while tightening Toggle Bolts. Pull Toggle Bolt toward
you and turn clockwise to tighten. Figure 14.
E5
INSTALLATION INSTRUCTIONS
9 OVEN INSTALLATION
cont.
Toggle Bolt
Toggle Nut
Mounting Plate
Figure 12
Space more
than wall
thickness
Figure 15
Figure 14
Wall
Figure 13
MOUNTING OVEN TO THE WALL
Two people are recommended to attach the Microwave Oven/
Hood to the Mounting Plate.
Tapping Screw
1. Thread the power supply cord through the hole made in
the bottom of the top cabinet.
Figure 16
2. Install the oven by tilting it forward and sliding it onto the
tabs of the Mounting Plate. Rotate the oven up so it rests
against the wall. See Figure 15.
Tapping Screw
3. Use the two Top Cabinet Screws and two Flat Washers,
supplied in the INSTALLATION HARDWARE, to attach
the unit to the top cabinet. See Figure 16.
4. Secure the bottom of the oven to the Mounting Plate
by using two Tapping Screws 4 x 8 mm from the
INSTALLATION HARDWARE. See Figure 16.
Figure 17
E6
INSTALLATION INSTRUCTIONS
CHECKLIST FOR INSTALLATION
1. Make sure the unit has been installed according to all of the
Installation Instructions and the Wall and Top Cabinet Templates.
2. Plug in the power cord.
3. Keep the Operation Manual.
E7
NOTES
E8
|