SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
Language Contents
OPERATING INSTRUCTIONS
FVH-E420
Video Cassette Recorder
®
Only cassettes marked w can be used with this video cassette recorder.
As an ENERGY STAR® Partner,
FISHER has determined that this
product or product model meets
the ENERGY STAR® guidelines for
energy efficiency.
(CA)
Please read this manual and accompanying “IMPORTANT SAFETY INSTRUCTIONS” sheet carefully before
connecting your VCR and operating it for the first time.
Be sure to read carefully and follow all the PRECAUTIONS on page 1.
Keep the manual in a safe place for future reference.
NOTE: Locate serial number (shown on rear panel of unit) and record it here ➡
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
FEATURES
CONTENTS
TIMER/CLOCK
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
œ Selectable standard/daylight saving time
œ 1-year/8-event program timer with daily/weekly settings
œ Smart Time Record function
œ Smart Speed Record function
œ Remaining tape duration display
œ Quick timer recording (QTR)
DESCRIPTION
VHS video cassette tapes . . . . . . . . . . . . . . . . . . . . 3
Locations of controls and indicators. . . . . . . . . . . . . 4
Remote control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
œ Off timer (up to 6 hours)
VIDEO
œ Digitally-adjusted clean playback
SPECIAL PLAYBACK/SEARCH
œ Ad JUMP®
CONNECTIONS
œ Recording contents on-screen list (Rec. List Super)
œ Double-Azimuth 4-head video recording/playback system for
clean special playback:
Basic antenna/cable connections. . . . . . . . . . . . . . . 9
Alternative cable TV connections. . . . . . . . . . . . . . 10
Audio/video connections . . . . . . . . . . . . . . . . . . . . 12
Forward/reverse search, double-speed playback, clean still
image, frame advance, variable-speed slow motion
œ Zero search
BASIC OPERATION
œ Index search
Initial setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Multifunction on-screen displays . . . . . . . . . . . . . . 15
On-screen menu. . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Setting the clock. . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Changing the menu language . . . . . . . . . . . . . . . . 20
Programming channels . . . . . . . . . . . . . . . . . . . . . 20
Viewing TV only . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Playing a rental tape. . . . . . . . . . . . . . . . . . . . . . . . 21
Normal playback. . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Tracking control . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Rec. List super . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
AUTOMATIC FUNCTIONS
œ Automatic clock setting and adjustment
œ Automatic head cleaner
œ Endless playback
œ Automatic digital tracking
œ Automatic channel programming
œ Full auto playback functions: power-on, rewind, eject, record
auto cancel, power-off eject
GENERAL
œ Multilanguage, multicolor on-screen menu
œ Remote control
œ Vibration-suppressing mid-mount design
œ Child lock
ADVANCED USE
ACCESSORIES
Make sure that all the accessories listed below have been
Special playback . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Zero search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Index search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Program timer recording. . . . . . . . . . . . . . . . . . . . . 29
Quick timer recording (QTR) . . . . . . . . . . . . . . . . . 33
Child lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ad JUMP®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Copying a tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
included with your VCR.
Power cord
Remote control
75-ohm coaxial cable
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Quick Start Guide
Quick Start Guide
xxxx xxx xxx xxxx xxx xxx xxx xxx
Guía rápida
x
xxxx xxx xxx xxxx xxx xxx xxx xxx
xxxxx xxxx xxxx xx xxxxx xxx xxx
xxxx
x
xxxxx xxxx xxxx xx xxxxx xxx xxx
x
x
Two AA batteries (1.5 volt)
xxxx
xxxx xxx xxx xxxx xxx xxx xxx xxx
x
xxxx xxx xxx xxxx xxx xxx xxx xxx
x
xxxxx xxxx xxxx
xxxx xxx xxx
x
xx xxxxx xxx xxx
xxxxx xxxx xxxx
xxxx xxx xxx
x
xx xxxxx xxx xxx
xxxx xxx xxx xxxx xxx xxx xxx xxx
xxxxx xxxx xxxx xx xxxxx xxx xxx
x
xxxx xxx xxx xxxx xxx xxx xxx xxx
xxxxx xxxx xxxx xx xxxxx xxx xxx
x
x
x
xxxx xx xxxxxxxxx xxx
xxxx xx xxxxxxxxx xxx
xxxx xxx xxx xxxx xxx xxx xxx xxx
x
xxxx xxx xxx xxxx xxx xxx xxx xxx
x
xxxxx xxxx xxxx
xxxx
x
xx xxxxx xxx xxx
xxxxx xxxx xxxx
xxxx
x
xx xxxxx xxx xxx
2
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
VHS VIDEO CASSETTE TAPES
Record/Play Times
Tape Length
T-60
T-120
T-160
2
SP Mode
1 hour
(60 minutes)
2 hours
(120 minutes)
2- ⁄ hours
highest video quality
excellent video quality
3
(160 minutes)
1
LP Mode
(playback only)
2 hours
(120 minutes)
4 hours
(240 minutes)
5- ⁄ hours
3
(320 minutes)
SLP Mode
3 hours
(180 minutes)
6 hours
(360 minutes)
8 hours
(480 minutes)
good video quality (longest
recording time)
NOTE: This unit cannot record in LP mode.
When Handling Video Cassettes
Safety Tab
œ Do not expose video cassettes to extreme heat, high
humidity or strong magnetic fields.
œ Do not tamper with the cassette mechanism.
œ Do not touch the tape with your fingers.
œ Always store an unused cassette in its case.
Arrow mark (
)
Label side up
(Arrow pointing toward slot)
To record again, cover
the hole with vinyl tape.
To prevent accidental
erasure, remove the
tab after recording.
Unloading
Loading
1 When in the STOP mode, press the STOP/EJECT
button on the front panel. In any other mode, press
the button twice.
1 Gently push the center of the cassette until it is drawn
in automatically.
The clock display changes to the tape counter
display automatically and the Tape-In icon (o)
lights.
The tape counter display changes to the clock
display automatically.
2 After the cassette appears in the loading slot, gently
NOTES:
pull it out.
œ If the cassette is not inserted correctly, it will be ejected
AUTO POWER-OFF/EJECT: The cassette is ejected
when the STOP/EJECT button on the front panel is
pressed, even if the VCR’s power is off. (The power cord
must be connected to an AC wall outlet.)
in approximately 3 seconds.
œ Do not try to pull the cassette out once automatic
loading starts.
œ Do not force the cassette into the VCR.
CAUTION: To avoid possible injury or accident, keep
children away from this unit. Do not put your hand or
other objects into the cassette loading slot.
3
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
LOCATIONS OF CONTROLS AND INDICATORS
Front Panel
1
PLAY c
STOP
EJECT
POWER
f REW
FF e
CHANNEL
REC PAUSE
STILL
G F 98 7
6
5 4 3 2
Reference pages are shown in square brackets.
1 Cassette loading slot
9 REC (record) button [23, 33]
F CHANNEL selection buttons (l and j) [14, 22, 33]
G POWER button
2 STOP/EJECT button [3, 22]
3 FF (fast forward) button [27]
This button is used both for fast forward and
forward picture search.
4 PLAY button [22]
5 REW (rewind) button [27]
This button is used both for rewind and reverse
picture search.
6 Indicator panel [5]
7 Remote control sensor
8 PAUSE/STILL button [23, 27]
œ Press this button in the record mode to
temporarily stop a recording (PAUSE).
œ Press this button in the playback mode to view a
still frame (STILL).
œ Press this button repeatedly in the still mode to
advance the picture one frame at a time.
4
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
LOCATIONS OF CONTROLS AND INDICATORS
Indicator Panel
1 Operation Icons (see below).
2 VCR indicator
1
2
3
Use the TV/VCR button on the remote control to turn
this indicator ON or OFF.
C
AM VCR
REC
ON: for playback, VCR programming or watching
TV programs through the VCR tuner
OFF: for watching TV programs through TV tuner
3 Tape-In icon
SP LP SLP
OFF
PM
4 Tape Speed indicators
8 7 6
5
4
5 Clock/ Tape Counter/ QTR (Quick Timer Recording)
indicators
6 Timer icon
Operation Icons
7 Input source indicator:
Play,
Forward
Search, Slow
Reverse
Search
Fast
forward
Rewind
Channel number or audio/video input (L1)
8 CATV indicator
J K L M
(blinking)
(blinking)
Record
Record pause
P P
and
O
(blinking)
Still
Frame advance
J
and
O J
and
N
(blinking)
Example of Indications
POWER OFF
POWER ON
CATV
indicator
Clock
Audio output
indicators
CATV
indicator
Clock
AM
C
AM
SP
Channel indicator
Tape speed indicator
Channel indicator
Tape speed indicator
5
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
LOCATIONS OF CONTROLS AND INDICATORS
Back Panel
1
2
3
VHF/UHF
FROM ANT.
IN
OUT
IN
VIDEO
TO TV
AUDIO
OUT
AC IN
6 5 4
1 AC power input
4 VHF/UHF antenna output jack
5 VIDEO output jack (yellow)
6 AUDIO output jack (white)
2 Rear-panel AUDIO/VIDEO input jacks
Connect the audio and video outputs from an
external unit (i.e. a video camera, second VCR) to
these jacks. To record the signals coming from the
external unit, press the INPUT button on the
remote control to display “L1” instead of a channel
number (see page 23).
3 VHF/UHF antenna input jack
6
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
REMOTE CONTROL
Reference pages are shown in square brackets.
Locations of Controls
1 TV/VCR mode button [13]
Lets you select TV or VCR mode. When VCR mode
is selected, the VCR indicator lights on the front panel.
1
2
MENU
TV/VCR
CLEAR
N
2 MENU button [16]
1
4
2
5
8
3
6
3 Number buttons (0 – 9) [14, 19]
4 100 button [14]
3
7
9
100
SET
5 POWER button [13]
0
4
O
P
REC
6 CH (channel) selection/TRACK (tracking) buttons
(l and j) [14, 22, 33]
POWER
CH/TRACK
5
6
7
•
û
7 PAUSE/STILL û button [16, 23, 27]
PAUSE/STILL
Q
R
•
8 REW (rewind) < button [17, 27]
REW
<
PLAY
OK
FF
>
8
9
•
9 STOP ù button [16, 23]
STOP
ù
F x2 button [27]
TV
TV INPUT POWER
G TYPE button [26]
x2
H SLOW button [27]
S
T
F
TYPE SLOW CH
VOL+
VOL–
G
I
I SP/SLP button [23]
J DISPLAY button [15, 28]
K INPUT button [23]
SP/SLP DISPLAY
CH
H
J
INPUT RESET Ö0Ü INDEX
K
M
Ad JUMP
L
U
L Tape counter RESET button [28]
M Ad JUMP button [34]
N CLEAR button [14]
O SET button [14]
P REC (record) button [23, 33]
•
Q PLAY OK button [16, 22]
•
R FF (fast forward) > button [17, 27]
S TV control buttons
Using the remote control
To enter the menu settings, use the ù, û, >, < or OK
(TV POWER, TV INPUT, CH l and j, VOL + and –)
T INDEX button [28]
button.
U →0← (Zero Search) button [28]
The ù button is equivalent to the STOP button, the û
button to the PAUSE/STILL button, the > button to the
FF button, the < button to the REW button and the OK
button to the PLAY button.
In this manual, the explanations are based on the
displayed menu screens and when doing operations
within a menu screen, “press the ù (û, >, < or OK)
button” will be indicated.
7
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
REMOTE CONTROL
Battery Installation and Operation
1 Install the two supplied AA batteries as shown.
2 Aim the remote control at the VCR and press the
desired buttons to operate.
IMPORTANT NOTE:
SPENT OR DISCHARGED BATTERIES MUST BE
RECYCLED OR DISPOSED OF IN A SAFE
MANNER IN COMPLIANCE WITH ALL
APPLICABLE LAWS.
FOR DETAILED INFORMATION, CONTACT YOUR
LOCAL COUNTY SOLID WASTE AUTHORITY.
NOTES:
œ The remote control will not operate properly if
something comes between the VCR and the remote
control.
œ This infrared remote control will also control the basic
functions of most Fisher TVs.
8
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
BASIC ANTENNA/CABLE CONNECTIONS
Antenna
VCR
(Back panel)
TV
(Back panel)
75 ohm
antenna
cable
VHF/UHF
FROM ANT.
VHF/UHF
ANTENNA
IN
or
IN
1
TO TV
AC Wall
outlet
OUT
AC IN
CABLE TV
3
2
(supplied)
4
NOTES:
1 Connect an antenna (or a cable TV system) to the
VCR.
œ If you have a cable converter connected to your TV,
see “ALTERNATIVE CABLE TV CONNECTIONS”,
next page.
2 Connect the VCR to the TV with the 75 ohm coaxial
cable (supplied).
œ If your antenna has a twin-lead cable or your TV has
screw-type antenna terminals, use a matching
transformer (not supplied).
3 Plug the power cord (supplied) into the AC power
input (AC IN ~) on the VCR back panel. Insert the
plug firmly.
4 Insert the plug end of this power cord into a wall
300 ohm
outlet.
Twin-lead Cable
Matching Transformer
(not supplied)
9
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
ALTERNATIVE CABLE TV CONNECTIONS
Your VCR can receive all unscrambled cable channels
without the use of an external converter. If you wish to
view and record scrambled cable channels, you must
connect a converter/decoder as described below.
Your local cable TV company will advise you of the
channels available in your area.
We recommend that you consult your cable TV company
to make sure that the cable is properly connected.
When the TV does not have a built-in cable converter
Connect the cable TV converter between the VCR and
the TV so that you can watch a cable TV program while
recording another program.
NOTE: Set the TV channel to the cable converter output
channel (CH02 ~ 07).
VCR
TV
Cable
CATV
(Back panel)
(Back panel)
converter
75 ohm
VHF/UHF
ANTENNA
IN
VHF/UHF
FROM ANT.
coaxial
cable
IN
OUT
IN
TO TV
OUT
AC IN
(not supplied)
(supplied)
When you have both cable and pay TV (scrambled channels)
NOTES:
œ With this method the TV and VCR receive the same
channel. Recording one program while watching
another is not possible.
œ With this connection, the VCR must be set to the cable
converter/decoder output channel. (See next page.)
VCR
(Back panel)
TV
Cable
converter/
Decoder
(Back panel)
VHF/UHF
ANTENNA
IN
VHF/UHF
FROM ANT.
IN
TO TV
CATV
OUT
75 ohm
AC IN
coaxial cable
(supplied)
NOTE TO CATV SYSTEM INSTALLER (USA only): This
reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practicable.
10
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
ALTERNATIVE CABLE TV CONNECTIONS
Cable converter/decoder output channel setup
1 Be sure the cable connections are correct.
7 Press the ù (or û) button to select the Cable box
(See page 10.)
option.
2 Turn on the TV, VCR and cable converter/decoder.
3 Set the TV to channel 3 or 4.
8 Press the > (or <) button to set your cable
converter/decoder output channel. The output
channel should be indicated on the cable
converter/decoder back panel. If not, please refer to
the cable converter/decoder instruction manual for
details.
4 If the VCR indicator is off, press the TV/VCR button
on the remote control.
The VCR indicator lights.
Press the > (or <) button repeatedly. Each time
you press the button, the selection changes:
NOTE: If the initial setup has not yet been
completed, the “Auto Setup” and “RF Channel Setting
Ch03 (or RF Channel Setting Ch04)” message will
appear. In that case, first follow steps 4 – 6 under
“INITIAL SETUP” on page 13.
No
Ch02
Ch03 ... Ch07
The selection is indicated by the “ z” next to it.
NOTE: Select “No” if you are not using the cable box.
5 Press the MENU button on the remote control.
9 When finished, press the MENU button to exit the
The main MENU appears.
menu display.
@@@@@@@@@MENU
Timer@program
VCR@setup
IMPORTANT NOTES:
Clock@set
When the cable converter/decoder output channel is
selected as described above,
Language@select
Rec.List@super
Auto@tuning@memory
œ The VCR tuner remains set to receive the same
channel as the output channel of the cable
converter/decoder. Auto channel programming and
manual channel selection using the VCR tuner are
not possible.
[ùû]†Select
[OK]†Set@@@@@@[MENU]†TV
6 Press the ù (or û) button to select the VCR setup
option, then press the OK button.
œ If you turn on the cable converter/decoder after
turning on the VCR, no image will appear on the TV
screen. In this case, turn off the VCR, then turn it on
again.
The VCR setup menu appears.
CATV/TV@@@@@@@zCATV@TV
Cable@box@@@@@zNo@@@Ch02
Child@Lock@@@@@On@@zOff
Off@timer@@@zOff@2Hr@6Hr
œ Leave the cable converter/decoder on until timer
recording is complete.
œ For timer recordings, you must select the channel to
be recorded using the channel selector on the cable
converter/decoder.
[ùû]†Option
[<>]†Select@@@[MENU]†TV
11
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
AUDIO/VIDEO CONNECTIONS
The VIDEO and AUDIO outputs of your VCR can be
connected separately to the input jacks of a TV monitor
and an audio system. This will provide the best possible
picture and sound quality, because the video/audio
signals from your VCR will not have to be processed by
the television tuner.
VCR
(Back panel)
COLOR TV/MONITOR
(Back panel)
VHF/UHF
FROM ANT.
VHF/UHF
ANTENNA
IN
OUT
IN
VIDEO
AUDIO
TO TV
VIDEO AUDIO
OUT
IN
IN
75 ohm coaxial
cable (supplied)
AUDIO VIDEO
OUTPUT OUTPUT
WHITE YELLOW
VIDEO
INPUT
YELLOW
AUDIO
INPUT
WHITE
2-wire monitor cable
(not supplied)
NOTES:
œ Even when audio/video connections are made, always
make the antenna connection between the VHF/UHF
OUT (VCR) and the VHF/UHF IN (TV) using the
supplied 75-ohm coaxial cable.
œ If a direct audio/video connection is made between the
VCR and the TV, set the source selector on the
television to A/V input.
12
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
INITIAL SETUP
When you are setting up the VCR for the first time, or
after the power has failed for more than 5 seconds, follow
the steps below. This AUTO SETUP operation
automatically sets the RF output channel, enters all
available channels in your area into the VCR tuner
memory and sets the VCR internal clock.
4 Press the OK button to save the RF output channel
setting.
The “RF-03 (or RF-04)” display on the indicator
panel will change to the clock display.
The Language select menu will appear.
Many TV stations transmit a signal called Extended Data
Services (XDS). This VCR uses the XDS signal to
automatically set the clock. If no XDS signal is available
in your area, the VCR prompts you to set the clock
manually.
@@@@Language@select
@@@@@@@@English
@@@@@@@@Español
@@@@@@@@Français
5 Press the ù (or û) button to move down or up the list
and highlight the language of your choice. Press the
OK button.
AUTO SETUP
œ During AUTO SETUP, do not press any buttons other
than the ones indicated here.
The menu language is selected.
“Auto tuning memory” appears on screen. The VCR
scans all 125 channels and memorizes each active
channel in your area in succession. It takes about
4-6 minutes.
Before starting
œ Be sure the antenna or cable connections are correct.
(See pages 9 and 10.)
6 When Auto Tuning is completed, the VCR will select
the channel that carries the XDS signal and proceed
to Auto Clock setting.
1 Press the POWER button on the VCR.
Auto RF output channel setting will start.
RF output channel setting rule
@@@@@@@@@@@@@@@@@@@@@@01
@@@@@@@Clock@set
Channel 3
No broadcast
No broadcast
Broadcasting
Broadcasting
Channel 4
No broadcast
Broadcasting
No broadcast
Broadcasting
RF output channel
Channel 3
Channel 3
The Auto Clock setting normally takes about
3 minutes. During this time, the VCR’s front panel
shows the channel number that is sending the XDS
signal for Auto Clock setting. Make a note of this
number, which you may need to refer to for
readjusting the clock later (see page 18).
Channel 4
Channel 3
The setting is completed, and “RF-03” (or “RF-04”)
will light on the indicator panel.
2 Turn on the TV power and turn to the indicated RF
If the Auto Clock setting entered the incorrect date
and/or time, correct it by following the steps under
Automatic Clock Adjustment on page 18.
channel.
3 If the VCR indicator is off, press the TV/VCR button
on the remote control.
If no XDS signal is available in your area:
The VCR indicator will light.
“Clock set” will not appear on the screen when the
Auto Tuning operation is completed. Instead, the TV
program on the lowest channel that the VCR
memorized will appear on screen. In this case, you
must set the clock manually. Follow the steps under
Manual Clock Setting on page 19.
The “Auto Setup” and “RF Channel Setting Ch03
(or RF Channel Setting Ch04)” message will
appears.
@@@@@@@Auto@Setup
@@RF@Channel@Setting
@@@@@@@@@@Ch03
NOTES:
œ The VCR will search for and memorize channels in the
CATV (cable TV) mode and TV mode.
This is your VCR channel. The TV must be set to
this channel whenever the VCR is used for playing
a tape or watching a TV program.
œ If the AC power to the VCR is interrupted for more than
5 seconds, the memorized RF output channel, channel
and clock may be erased.
To change the RF output channel setting, press the
number button 3 (or 4).
13
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
INITIAL SETUP
To modify the RF output channel
setting after the Auto setup is
completed
Manual Erase
You can eliminate unwanted channels or channels with
weak or scrambled signals from the memorized channel
sequence.
1 With the VCR turned off, press the SET button for
1 Select the channel you want to erase.
about 3 seconds or more.
2 Press the CLEAR button for about 2 seconds.
“Erase” is displayed on-screen for about 3 seconds.
The channel is now erased from the memory.
The current RF output channel setting will light on
the indicator panel and will appear on the screen.
2 Press the number button 3 (or 4).
After about 5 seconds, the RF channel setting
value is saved, and the VCR will turn off.
Manual Programming
You can add channels to the memorized channel
sequence by manually adding them to the tuner memory.
Channel Selection Convenience
You can select a channel on your VCR by using one of
the two methods shown below:
1 Select the channel you want to add using the number
buttons on the remote control.
2 Press the SET button for about 2 seconds.
“Add” is displayed on-screen for about 3 seconds.
The channel is now added to the memory.
10-KEY RANDOM ACCESS TUNING
Select the desired channel number by using the number
buttons and 100 button on the remote control. For
single-digit numbers, press 0 first. For channel numbers
higher than 99, press the 100 button first.
UP/DOWN SELECTION
Press and hold the CH/TRACK down (l) or up (j) (or
CHANNEL on the front panel) button until the desired
channel is received.
NOTE: When an inactive TV channel is selected on the
VCR, the “No Signal” message appears and the sound is
muted.
14
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
MULTIFUNCTION ON-SCREEN DISPLAYS
Various displays appear, superimposed over the screen
image, indicating the operation mode and features in use.
Status display
1 Press the DISPLAY button on the remote control.
Operation mode
Program title
QTR end time
The status display appears.
Channel/AV
p QTR10:30PM
C 10
C 10
SPORTS DIGEST
SP 0:00:00
09:30PM
Clock
Recording
tape speed
SP 0:00:00
09:30PM
Counter
2 To remove the status display, press the DISPLAY
button (press the button twice if a tape is loaded in
the VCR).
Operation Mode Display
When an operation button is pressed, the corresponding
operation mode icon is displayed in the top left corner of
the screen for about 3 seconds.
NOTE: The status display will not appear if a menu is
displayed on screen, or during special playback.
NOTE: The recording pause mode icon will remain
displayed until recording is resumed or stopped.
Remaining Tape Duration Display
Operation
Play
Icon
c
Operation
Record
Icon
a
1 Press the DISPLAY button twice.
The remaining tape duration appears at the bottom
of the screen. It is calculated in hours and minutes
from the current position to the end of the tape.
Fast-forward
Rewind
c c
d d
Record pause
a h
SP Tape remain 2:30
Channel Number Display
The channel number display appears for about 3 seconds
when a channel is selected.
If “ --:--” is displayed, the remaining tape
duration has not been calculated.
2 To remove the remaining tape duration display, press
the DISPLAY button again.
Program Title Display
When a channel is tuned or when normal playback is
started, the program title (maximum 24 characters) will be
displayed for about 4 seconds.
NOTES:
œ The remaining tape duration display will not appear if a
menu is displayed on screen or during special playback.
NOTES:
œ This feature will not work properly on T-140 tapes or
tapes longer than T-160. (The feature will work on
T-160 tapes.)
œ The program title is only displayed if the broadcast
carries the title information or if it has been recorded on
the tape.
œ Depending on the condition and type of tape used, the
VCR may not accurately detect the remaining tape
duration.
œ Depending on the TV signal or tape condition the
program title may not be displayed even if it is available.
Recording Tape Speed Display
The recording tape speed is displayed for about 3
seconds after recording is started or when the tape speed
is changed. The “SS” display means that the smart speed
record function is used (see page 24).
15
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
ON-SCREEN MENU
Your new VCR is designed with user-friendly on-screen
menus to help you operate its many features.
Color-coded menus prompt you step-by-step through
operations by highlighting the sections awaiting your
entries.
Main Menu Options
Reference pages are shown in square brackets.
Timer program [29 – 32]
œ Select this to program, check or cancel a timer
recording setting.
Displaying the On-Screen Menus
VCR setup [17]
œ Select this to set the VCR functions.
Clock set [18, 19]
1 Turn on the power (TV and VCR).
2 Set the TV to channel 3 or 4.
œ Select this to set the clock or change the clock
3 If the VCR indicator is off, press the TV/VCR button
setting.
on the remote control.
Language select [20]
The VCR indicator lights.
œ Select this to change the on-screen language.
Rec. List super [25, 26]
NOTE: If the initial setup has not yet been
completed, the “Auto Setup” and “RF Channel Setting
Ch03 (or RF Channel Setting Ch04)” message will
appear. Follow steps 4 – 6 under “INITIAL SETUP”
on page 13.
œ Select this to list the recordings on the tape
inserted in the VCR.
Auto tuning memory [20]
4 Press the MENU button on the remote control.
œ Select this to program the channels into the VCR’s
The main MENU appears.
tuner memory.
@@@@@@@@@MENU
Timer@program
VCR@setup
Menu title
Option
selected
Clock@set
Language@select
Rec.List@super
Auto@tuning@memory
[ùû]†Select
[OK]†Set@@@@@@@[MENU]†TV
Operations
indications
The menu items are color-coded as shown below:
œ Menu title:
On magenta background
Highlighted in green
œ Option selected:
œ Operations indications: On blue background
œ Others:
On gray background
NOTE: If the clock has not yet been set, the Clock
set menu appears. To set the clock, see “SETTING
THE CLOCK” on page 18.
Press the ù (or û) button to select the desired
option, then press the OK button.
5 Press the MENU button to exit the menu.
16
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
ON-SCREEN MENU
Displaying the VCR Setup Menus
Before starting
VCR Setup Menu Options
Reference pages are shown in square brackets.
CATV/TV [20]
œ Turn on the power (TV and VCR).
œ Set the TV to channel 3 or 4.
œ Indicate whether you subscribe to cable TV or use
antenna.
œ If the VCR indicator is off, press the TV/VCR button
Cable box [11, step 8]
on the remote control.
œ If you use a cable converter/decoder (cable box),
The VCR indicator lights.
set the output channel.
Child Lock [34]
1 Press the MENU button on the remote control.
œ Select this to block picture and sound.
Off timer
The main MENU appears.
œ Select this to set the VCR to automatically shut off
2 Press the ù (or û) button to select the VCR setup
option, then press the OK button.
after a specified period of non-operation.
Off: The power will not be turned off automatically.
2Hr: The power is turned off after 2 hours.
6Hr: The power is turned off after 6 hours.
The VCR setup menu appears.
CATV/TV@@@@@@@zCATV@TV
Cable@box@@@@@zNo@@@Ch02
Child@Lock@@@@@On@@zOff
Off@timer@@@zOff@2Hr@6Hr
NOTE: The Off timer begins counting down after the
last VCR activity. Approximately 5 minutes before the
power is turned off, the “Your VCR will be off shortly”
message is displayed.
[ùû]†Option
[<>]†Select@@@[MENU]†TV
3 Press the ù (or û) button to highlight the desired
option.
4 Press the > (or <) button once or more to move the
“z” indicator in front of your selection.
5 When finished, press the MENU button to save the
settings.
17
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
SETTING THE CLOCK
Generally, during the initial setup, your VCR will
automatically set the clock by detecting a channel that is
transmitting the XDS (Extended Data Services) signal.
However, if the XDS signal necessary for Automatic
Clock Setting was poor or unavailable at the time,
Automatic Clock Setting may not have been possible.
Automatic Clock Adjustment
1 Press the MENU button.
The main MENU appears.
2 Press the ù (or û) button to select the Clock set
option, then press the OK button.
Follow the steps below to set the clock.
The Clock set menu appears.
Before starting
@@@@@@@Clock@set
œ Turn on the power (TV and VCR).
œ Set the TV to channel 3 or 4.
@03/07[Wed]2001@09:30@PM
Clock@adjust@@zAuto@Off
œ If the VCR indicator is off, press the TV/VCR button
on the remote control.
[DISPLAY]†Clock@adjust
[ùû]†Day/STD@shift
[>]†AM/PM
The VCR indicator lights.
[<]†Cancel
[OK]†Set
1 Press the STOP button, then enter the channel
number that you have made note of during Automatic
Clock Setting (see page 13).
3 Press the < button until the wrong clock setting is
erased, then enter the correct time.
2 Press and hold the PAUSE/STILL button for more
4 Press the DISPLAY button to set the Clock adjust
than 2 seconds.
option to Off.
If the channel is transmitting the XDS signal,
“Clock set” starts blinking on screen after
approximately 4 seconds.
5 When finished, press the OK button to exit from the
menu.
When you set the Clock adjust option to Auto, the
time will automatically be adjusted twice a week
(every Sunday at 3:00 AM and 6:00 AM) according
to the XDS signal.
When Automatic Clock Setting is completed, the
screen shows the current TV program.
If the screen returns to the current TV program
immediately, the XDS signal for clock setting is not
available in your area. Use the Manual Clock
Setting procedure on page 19.
If the automatic clock setup procedure enters the
wrong time, make sure to select Off for the Clock
adjust option. If set to Auto, an incorrect time will
be entered again at the next automatic clock
adjustment.
NOTE: If the Automatic Clock Setting procedure set the
wrong clock time, follow the steps under Automatic Clock
Adjustment.
NOTES:
œ The Clock adjust option appears only when the clock
has been set automatically.
œ The automatic clock adjustment will not be performed if
the power is on, or if a program timer recording is set to
start within 5 minutes of the automatic clock adjustment
times (2:55 AM – 3:05 AM and 5:55 AM – 6:05 AM).
œ If using a cable converter/decoder, the automatic clock
adjustment may not function properly.
18
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
SETTING THE CLOCK
Manual Clock Setting
Standard/Daylight Time Adjustment
The clock time can be easily changed to daylight saving
time (by adding one hour) or standard time (by
subtracting one hour).
1 Follow the steps in Before starting.
2 Press the MENU button.
The main MENU appears.
1 Press the MENU button.
If the clock has not yet been set, the Clock set
menu appears.
The main MENU appears.
2 Press the ù (or û) button to select the Clock set
option, then press the OK button.
3 Press the ù (or û) button to select the Clock set
option, then press the OK button.
3 Press the ù (or û) button.
The Clock set menu appears.
Every time the ù (or û) button is pressed, 1 hour is
subtracted (or added) to the displayed time.
@@@@@@@Clock@set
4 When finished, press the OK button to save the
@MM/DD[@@@]@@YY@HH:MM
settings.
[<]†Cancel
[MENU]†Back@to@TV
4 Press the number buttons (0 – 9) to set the date and
time.
œ EXAMPLE: Setting the clock to standard time.
March 7, 2001, 9:30 PM (03/07/01, 9:30 PM).
œ Date March 7:
Press 0 – 3 – 0 – 7
Press 0 – 1
Year ’01:
Time 9:30:
PM:
Press 0 – 9 – 3 – 0
Press >
@@@@@@@Clock@set
@03/07[Wed]2001@09:30@PM
[ùû]†Day/STD@shift
[>]†AM/PM
[<]†Cancel
[OK]†Set
NOTES:
œ When entering the year, press the two number
buttons that correspond to the last two digits of the
year (i.e. 00 for 2000, 05 for 2005 or 25 for 2025).
œ If you press the wrong button, press the < button to
erase the wrong number. Then press the correct
button to continue.
5 When finished, press the OK button to save the
settings.
19
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
CHANGING THE MENU LANGUAGE
English, Spanish or French can be selected by the user.
1 Press the MENU button.
The main MENU appears.
Before starting
2 Press the ù (or û) button to select the Language
select option, then press the OK button.
œ Turn on the power (TV and VCR).
œ Set the TV to channel 3 or 4.
3 Press the ù (or û) button to select the language of
your choice, then press the OK button.
œ If the VCR indicator is off, press the TV/VCR button
on the remote control.
The Language select menu disappears, and the
on-screen menu language has been selected.
The VCR indicator lights.
PROGRAMMING CHANNELS
Once the initial setup is completed, the channels can be
programmed again. This may be necessary if you are
switching from cable service to antenna reception.
4 Press the ù (or û) button to select the CATV/TV
option, then press the > (or <) button to select
“CATV” (if you subscribe to a cable TV service) or
“TV” (for normal broadcast reception through an
antenna).
NOTES:
œ Make sure the antenna or cable connections are
The CATV indicator “C” displayed on the indicator
panel means that the cable TV system is selected.
correct. (See pages 9 and 10.)
œ If the input source is set to L1, press the INPUT button
on the remote control until the indicator panel shows a
channel number.
5 Press the MENU button twice.
The main MENU appears.
6 Press the ù (or û) button to select the Auto tuning
memory option, then press the OK button.
Channel Programming
The VCR programs all unscrambled channels that
are available in your area into the tuner memory.
1 Follow the steps in Before starting above.
2 Press the MENU button.
The “Auto tuning memory” message is displayed
while the channels are automatically set.
The main MENU appears.
3 Press the ù (or û) button to select the VCR setup
option, then press the OK button.
The VCR setup menu appears.
CATV/TV@@@@@@@zCATV@TV
Cable@box@@@@@zNo@@@Ch02
Child@Lock@@@@@On@@zOff
Off@timer@@@zOff@2Hr@6Hr
[ùû]†Option
[<>]†Select@@@[MENU]†TV
20
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
VIEWING TV ONLY
You do not need to disconnect the VCR from the TV in
order to watch a TV program without recording it.
1 Turn off the VCR.
2 Turn on the TV and set it to the channel you want to
watch.
PLAYING A RENTAL TAPE
When you load a cassette with the safety tab removed,
the VCR starts playing it automatically.
Before starting
œ Turn on the TV.
œ Set the TV to channel 3 or 4.
This VCR features full automatic playback and rewind.
Load a cassette (with the safety tab removed).
œ The power turns on automatically and playback begins.
œ At the end of the tape, the VCR stops, then rewinds.
œ The cassette is ejected after rewinding.
No safety tab
Playback of Copyguarded Tapes
Some prerecorded tapes employ a copyguard system
that may cause intermittent distortion in the upper portion
of the picture during playback. (This distortion is more
likely to be visible on an older TV.) If you experience this
problem, do the following:
1 Select a TV station with a strong, clear signal.
2 Record a brief segment of that station’s programming.
3 Play back the recording.
If the playback picture is clear, the VCR is operating
properly. The distortion on the prerecorded tape is due to
the copyguard system.
21
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
NORMAL PLAYBACK
Digitally-Adjusted Clean Playback
Before starting
Advanced technology developed by Fisher enables your
VCR to detect imperfections in the condition of a
recording (an old recording that has been played back
many times, for example) then automatically adjust the
playback signal to deliver the best possible image.
œ Turn on the power (TV and VCR).
œ Set the TV to channel 3 or 4.
œ Load a cassette.
1 Press the PLAY button.
Normal playback begins.
The tape counter starts.
The tape stops and rewinds when the end of the
tape is reached.
2 Press the STOP button (or STOP/EJECT on the front
panel) to stop playback.
œ To rewind the tape, press the REW button.
œ To fast forward the tape, press the FF button.
NOTES:
œ When the tape comes to a blank segment during
playback, the “No Signal” message appears and the
sound is muted.
œ If the playback picture shows noise or no video at all
while audio is properly heard, first try the manual
tracking adjustment. If this does not correct the
problem, it may indicate that the video heads need
maintenance. Contact an authorized service center.
TRACKING CONTROL
Tracking Control Adjustments
When you play a tape that was not recorded on this VCR,
some noise may appear in the picture due to incorrect
head-to-tape tracking.
The VCR will automatically adjust the tracking for the
optimum results.
If noise still appears:
MANUAL TRACKING CONTROL
1 Press and hold the CH/TRACK l or j button (or
CHANNEL on the front panel) during playback to
eliminate the noise streaks from the picture.
The automatic tracking control mode is canceled.
To return to automatic tracking, eject the cassette,
then reinsert it.
22
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
RECORDING
Before starting
Rec. List Super Feature
The Rec. List Super feature lets you keep track of all
recordings you make on this VCR. The information
automatically includes the channel number, date and start
time. In addition you have an option to add the program
type to the information list. See page 25 for more detailed
instructions on the Rec. List Super feature.
œ Turn on the power (TV and VCR).
œ Set the TV to channel 3 or 4.
œ If the VCR indicator is off, press the TV/VCR button
on the remote control.
The VCR indicator lights.
œ Press the INPUT button on the remote control to
select the tuner mode. (See “Recording Input
Options”.)
Recording One Program While
Viewing Another
A channel number appears.
1 Follow the steps 1 – 3 in “RECORDING”.
œ Load a cassette.
2 Press the TV/VCR button.
The VCR indicator goes off.
1 Select a channel to record (on the VCR).
3 Tune the TV to the channel you want to watch.
2 Press the SP/SLP button on the remote control to
select the tape record speed, if necessary.
NOTES:
Selected Tape Speed indicator lights.
œ If you have connected your cable converter/decoder to
the input of the VCR, recording one program while
watching another is not possible.
If the SP and SLP indicators are both on, the smart
speed function is set (see the next page).
3 Press the REC button.
The Record indicator (Z) lights.
Recording begins.
œ If audio/video connections are made between the VCR
and the TV, set the source selector on the television to
TV.
RECORD AUTO CANCEL: Recording will not start if
the safety tab has been removed from the cassette.
The cassette will automatically be ejected.
Recording Input Options
You can record not only from the VCR tuner (TV
programs), but also from the external equipment (i.e,
another VCR, camcorder or digital camera) connected to
the rear-panel A/V inputs.
4 Press the PAUSE/STILL button to temporarily stop
recording (record pause mode).
The Pause/Still indicator (r) blinks.
Before starting to record, make sure the correct input
source is shown in the front-panel indicator. If not, press
the INPUT button on the remote control until you see the
correct input source.
During the pause, if you want to change the
channel, press the CH/TRACK l or j button on
the remote control (or CHANNEL on the front
panel).
If the record pause mode continues for
approximately 5 minutes, the VCR automatically
stops recording.
Recording source
Indicator shows:
VCR Tuner (TV programs)
Selected channel number
External unit connected to
the rear-panel A/V jack
5 Press the REC button, or press the PAUSE/STILL
L1
button again.
The Pause/Still indicator goes off.
Recording continues.
6 Press the STOP button (or STOP/EJECT on the front
panel) when you want to stop recording.
The Record indicator goes off.
23
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
RECORDING
Smart Speed Record Function
When the Smart Speed Record function is set, the VCR
automatically calculates the remaining time left on the
tape during recording. If there is not enough time left for
the program to be recorded, the VCR switches the
recording speed from SP (standard play) to SLP (super
long play) to enable the entire program to fit onto the
remaining tape.
œ To set the Smart Speed Record function, press the
SP/SLP button until “SS” is displayed on-screen at the
Recording tape speed display position (or both SP and
SLP indicators light on the indicator panel).
Recording will start in SP mode. During recording, based
on a calculation using the remaining tape and the XDS
signal information, if the remaining tape duration is not
enough to record the program to the end, the recording
speed will be automatically switched to SLP mode. If the
necessary information is not contained in the received
XDS signal, the recording will be done in SP mode.
For example, when recording a 150-minute program
onto a T-120 (120-minute) tape:
The recording will be done in SP mode for almost 105
minutes and in SLP mode for the last 45 minutes.
During Smart Speed Recording, the current recording
speed indicator will flash on the display.
During Smart Speed Recording, SS will appear on the
screen.
NOTES:
œ During timer recording, the set end time will be
considered as the time the program ends.
œ If during Quick Timer Recording (QTR), the end time is
set using the REC and/or CH/TRACK l (or j) buttons,
the duration until the set end time will be considered as
one single program.
œ This feature will not work properly on T-140 tapes or
tapes longer than T-160. (The feature will work on
T-160 tapes.)
œ If two or more timer recordings are programmed, all the
programs may not fit onto a single tape. In that case,
make sure the Smart Speed Record mode is not set,
and select the recording speed manually.
œ There may be some interference in the image at the
point where the speed has been switched.
œ If a program to be taped cannot fit into the remaining
time left on the tape, even in SLP mode, the program
will not be recorded till the end.
24
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
Rec. List SUPER
5 Press the STOP button, if the desired recording is
Rec. List (Recording Contents List)
Super
listed.
6 Press the ù (or û) button to set the desired recording,
then press the OK button.
Every time a recording is made with this VCR, the
channel number, date and start time information is
automatically recorded on the tape. When you call up the
Rec. List super menu, the VCR scans the information on
the tape and displays it on screen. You can then use the
menu to easily find a desired recording and play it back at
the touch of a button.
“Searching” will flash on screen while the tape
rewinds to the beginning of the selected recording.
Playback will start automatically.
NOTES:
œ To cancel the operation, press the STOP button. The
scanned section of the list will be kept in the VCR
memory until the tape is removed from the VCR.
The Rec. List super feature also gives you the option of
adding the type (or title) of program you record to the list.
To use this option, you must select the type name using
the Type input menu before setting up the recording. See
next page for more detailed instructions.
œ The scanned Rec. List super information will be kept in
the VCR memory until the tape is removed from the
VCR.
1 Load a cassette that has been recorded on this unit.
œ When 8 or more recordings are found on the tape, the
2 Press the MENU button.
list scrolls up, and the last 7 recordings are listed.
The main MENU appears.
œ The list shows “ – – ” for the sections where there is no
data or the data is unreadable (recorded by another
VCR, for example).
3 Press the ù (or û) button to select the Rec. List super
option, then press the OK button.
The Rec. List super menu appears.
œ A recording shorter than 5 minutes may not be listed.
œ When a second selection for playback is made (after
having played the first selection), the tape first rewinds
to the beginning before searching for the selected
recording.
@@@@@Rec.List@super
@@Ch@Date@@Start@@Type
œ If a new recording is made over an old one, the Rec.
List super information from the old recording will be
deleted.
œ If the tape is ejected while the recording list menu is
[OK]†Start
displayed, the menu disappears.
NOTE: If no cassette tape is loaded, the Rec. List
super menu will not be displayed.
4 Press the OK button.
The tape rewinds to the beginning. Then the VCR
begins scanning the tape for the Rec. List super
information and when detected, displays it on
screen. Wait for the desired recording to be listed.
@@@@@Rec.List@super
@@Ch@Date@@Start@@Type
@@01@5/06@@9:00«@@Movie
@@22@5/15@@6:30»@@-----
@@04@5/21@@7:30»@@Sport
@@L1@5/27@@7:30»@@Game
@@05@6/01@@SPORTS@DIGEST
@@L1@6/02@@6:30»@@Child
@@--@-/--@@-:--@@@-----
[ùû]†Select@@@@[OK]†Play
25
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
Rec. List SUPER
NOTES:
Entering the Program Type
œ To enter the selected program type, press the SET
To have the program type included in the Rec. List super
menu, you must enter the program type before
button within 10 seconds after selecting a program type.
proceeding to step 1 of “RECORDING” on page 23.
œ Program types set manually have priority over
automatic settings.
œ The clock must be set before the program type can be
selected.
œ After pressing the POWER button (to switch off the
power), or ejecting the cassette, the selected type will
be cancelled if no recording have been made.
1 Press the TYPE button on the remote control.
The Type input menu will be displayed on screen.
Type†Auto
2 Press the TYPE button repeatedly until the desired
program type is displayed.
Each time the TYPE button is pressed, a different
type, “-----”-Movie-Talk-Sport (Sports)-Game-
Soap-News-Child-Auto is displayed.
Auto: If the recorded program transmission carries
title information, it will automatically be entered.
Then, when using the Rec. List super function, the
title will be displayed (up to 15 characters).
“-----”: The program type is not set.
Other settings: When using the Rec. List super
function, the setting entered here will be displayed
as the program type.
3 Press the SET button to enter the settings.
The entered type code (e.g. Movie → MO) will be
displayed for about 3 seconds on the indicator
panel.
26
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
SPECIAL PLAYBACK
Picture Search (Forward and Reverse)
Endless Playback
This function will play back a tape to the end, rewind it
and then replay and rewind over and over until you stop it.
1 Press the FF or REW button during normal playback.
The picture plays forward or backward rapidly.
1 In the stop or playback mode, press and hold the
PLAY button on the front panel, then while holding it
down press the REW button on the front panel.
2 Press the PLAY button to resume normal playback.
FR (Fast Response) Search
The tape rewinds to the beginning, then endless
playback starts.
1 Press the FF button (in fast forward mode) or the
REW button (in rewind mode).
2 Press the STOP button (or STOP/EJECT on the front
panel) to cancel endless playback.
The forward or reverse picture can be viewed.
NOTE: If an operation button is pressed during
endless playback, the function is cancelled.
2 Press the FF or REW button again to return to the
fast forward or rewind mode.
If noise appears on double-speed or slow motion
play:
Still Image
Press and hold the CH/TRACK l (or j) button (or
CHANNEL on the front panel) to reduce the noise.
1 Press the PAUSE/STILL button during normal
playback.
The Pause/Still indicator (r) blinks.
If noise appears on a still picture:
A still image appears on the screen.
Start slow motion play, and then repeat the operation
above.
2 Press the PLAY button to resume normal playback.
œ This adjustment also corrects tracking errors for a still
picture.
Slow Motion
If the picture is unstable (vertical jitter) during
double speed playback, still or slow motion
modes
1 Press the SLOW button on the remote control during
normal playback.
Slow motion playback starts.
The slow-motion playback speed switches
between 1/5 and 1/30 of normal playback each
time the SLOW button is pressed.
1 Press the PLAY button.
2 Press the PAUSE/STILL button.
A still image appears on the screen.
2 Press the PLAY button to resume normal playback.
3 Press and hold the CH/TRACK l or j button (or
CHANNEL on the front panel) to reduce the vertical
jitter.
Frame Advance
œ This adjustment also corrects tracking errors during
1 Press the PAUSE/STILL button repeatedly during still
double speed playback and slow motion playback.
mode.
The picture advances one frame at a time.
NOTES:
2 Press the PLAY button to resume normal playback.
œ During special effects playback, the sound is muted.
œ Noise bands (narrow white lines in the picture) may
appear during picture search. This is normal and
cannot be eliminated by using the tracking control.
Double Speed Playback
1 Press the x2 button during normal playback.
œ After staying in still or slow motion playback for
The picture plays back at about 2 times the normal
playback speed.
5 minutes, the VCR automatically stops.
2 Press the PLAY button to resume normal playback.
27
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
ZERO SEARCH
Use the zero search function to go back to the beginning
of a program immediately after you have recorded it.
NOTES:
œ The tape counter indicates tape elapsed time in hours,
1 Press the DISPLAY button.
minutes and seconds.
The status display appears.
œ When you eject a cassette, the tape counter resets to
0:00:00.
2 Press the RESET button.
œ The tape counter does not operate when a blank tape
The tape counter resets to 0:00:00.
or a blank portion of a tape is played.
3 Begin playback or recording.
œ If the tape is rewound beyond the 0:00:00 counter
reading, a negative indicator (–) appears.
4 Press the STOP button (or STOP/EJECT on the front
panel) to stop playback or recording.
5 Press the →0← button.
“ e 0:00:00 f” is displayed on screen for about
3 seconds.
The tape rewinds and will stop at or near the
counter zero (“0:00:00”) position.
INDEX SEARCH
You can easily return to the beginning of the current
program or skip to the beginning of the next program and
start playback.
INDEX SEARCH Operation
Tape beginning
Tape end
Recorded Tape
œ EXAMPLE: To skip to the next program.
Present tape position
1 Press the INDEX button in the play or stop mode.
“f Index Search e” will be displayed on-screen.
Current
Next
Program
Program
2 Press the FF button.
The tape quickly advances to the beginning of the
next program.
Playback
starts
Playback
starts
Playback begins.
For the current
program, press
the REW button.
For the next
program, press
the FF button.
NOTES:
œ There may be a slight discrepancy between the
position shown on the tape counter and the actual tape
position.
œ Each time a recording is made, an index code is
automatically placed on the tape at the beginning of the
recording.
œ When a recording is resumed after a record pause, no
index code is marked.
œ The index codes cannot be individually erased.
However, when recording over an indexed tape, the old
index codes will be erased along with the programs.
28
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
PROGRAM TIMER RECORDING
The Program Timer switches your VCR on and off to
record a TV program at a preset time. On any occasion,
you can preset a maximum of 8 programs to be recorded
during the next 1-year period.
Each time the > button is pressed, a different
recording mode (Daily – Weekly – Once) is
selected.
Set the start and end time.
You can also set any of the 8 time slots to repeatedly
record the same channel at the same time daily (Monday
through Friday) or weekly. Daily and weekly settings are
retained in the timer memory and will continue to cue the
VCR to record as long as tape is available.
Start time 9:00 PM:
End time 10:30:
Press 0 – 9 – 0 – 0 –>
Press 1 – 0 – 3 – 0
The end time AM/PM setting will be entered
automatically.
NOTE: If you press the wrong button, press the <
button to erase the wrong number. Each time the <
button is pressed, the previous number will be
erased. Press the correct button to continue.
During timer programming, you may want to take
advantage of convenient features that give you the option
of saving the title/type of program being recorded (Rec.
List Super, page 25), having the VCR automatically set
the proper tape speed (Smart Speed Record Function,
page 24), and having the VCR automatically adjust the
start and stop times (Smart Time Record Function, page
30).
5 To change the recording tape speed, press the
SP/SLP button.
For automatic speed selection, select “SS” for tape
speed. (See Smart Speed Record Function on
page 24.)
NOTE: The clock time must be set before a timer
recording can be programmed.
@Ch@@Date@@Start@@End
@10@3/09Fr@9:00»@ï:30»è
@--@-/--@@@-:--@@-:--@--
Timer Programming
1 Follow the “Before starting” steps, under
6 Press the OK button.
“RECORDING” on page 23.
If you do not want to use other options, proceed to
step G.
2 Press the MENU button.
The main MENU appears.
Continued on the next page. _
3 Press the OK button.
The Timer program menu appears.
@Ch@@Date@@Start@@End
@--@M/DD@@@H:MM@@H:MM@SP
@--@-/--@@@-:--@@-:--@--
4 Press the number buttons (0 – 9) to set the timer
program.
œ EXAMPLE: To record a program on channel 10
once (Once recording mode) on March 9, from
09:00 PM to 10:30 PM, using the SLP recording
speed (March 9 = 03/09).
œ Channel 10:
Press 1 – 0
Press 0 – 3 – 0 – 9
Date March 9:
Daily/Weekly setting: Press >
Timer Recording Modes
Daily (M-F):
Records a program at the same
time, Monday through Friday.
Weekly (WK): Records a program on the same
day and time each week.
29
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
PROGRAM TIMER RECORDING
7 Press the TYPE button.
Smart Time Record Function
The Type and Smart Time Rec. setting menu
appears.
Sometimes, TV program start or end times are later than
published schedules. With the Smart Time Record
function, the VCR is informed of the altered times and
adjusts Program Timer recording to the actual broadcast
time.
Ch@@Date@@Start@@End
10@3/09Fr@9:00»@ï:00»è
@@@@@@@Type:@Auto
This function operates by recognizing program rating
signals incorporated into broadcasts. When you have
programmed the timer up to step 6, you can call up the
Type and Smart Time Rec. setting menu by pressing the
TYPE button on the remote control and then follow steps
7 through G on page 30.
Smart@Time@Rec.@setting
@@@@@@@zOff@@On
[ùû]†Select
[TYPE]†Type@@@@@@@@@[OK]
Not all TV stations transmit rating information signals.
8 Press the TYPE button repeatedly to select the
correct program type. (See Entering the Program
Type on page 26.)
NOTES:
œ If more than one programmed recording set with the
Smart Time Record function is delayed, the VCR will
wait (up to 3 hours) for the first one to be broadcast and
that program will have priority over the other
programmed recordings.
9 Press the ù (or û) button to select the Smart Time
Rec. setting option.
F Press the TYPE button repeatedly to select the
correct rating. (See Smart Time Record Function on
page 30.)
œ If the option Auto A/V select is set to “On” and the input
at the front A/V input connectors is being viewed, when
a program is delayed, the message “Smart Time Rec.”
will flash from the scheduled start time (setup on the
VCR) to the actual start time of the program broadcast
(up to a maximum of 3 hours).
Each time you press the TYPE button, the
selection changes: OFF → TV-Y → TV-Y7 →
TV-G → TV-PG → TV-14 → TV-MA → G → PG →
PG-13 → R → NC-17 → X.
Select OFF if you are not using the Smart Time
Record function.
œ If the start time of a programmed recording not using
the Smart Time Record function is reached during the
start time wait period for a delayed recording
programmed with the Smart Time Record function, the
recording programmed without the Smart Time Record
function will have priority and will first be recorded to
the end.
G Press the OK button.
The next timer recording slot can be programmed.
When two or more program timer recordings are
set, they will be listed in chronological order of the
recording start times with the earliest time listed
first.
œ If the Smart Time Record function is set after having
set the Smart Speed Record function, the tape speed
will change to SLP and the Smart Speed Record
function will not operate. Note that even if the Smart
Time Record function is set to “Off”, the tape speed will
remain as set and will not return automatically to its
previous setting.
H When finished, press the MENU button to exit the
menu.
I Press the VCR POWER button.
The VCR power turns off and the timer is set to the
recording standby mode.
œ If the program transmission start time is delayed more
The Timer icon (n) appears.
than 3 hours the function will be canceled.
œ If the previous and following programs are not rated,
and the desired program broadcast time is changed,
the unit may record some of the previous or following
program.
30
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
PROGRAM TIMER RECORDING
Setting a Program Timer Recording
Using the Buttons on the VCR
If the remote control does not operate or is not available
you can use the buttons on the VCR front panel to set a
program timer recording.
Checking the Program Timer
1 Turn on the power (TV and VCR).
2 Set the TV to channel 3 or 4.
3 Press the MENU button.
The main MENU appears.
NOTE: Eject the cassette tape, before proceeding with
the steps below.
4 Press the OK button.
1 Press and hold the REC button on the front panel for
The programmed recordings are listed.
about 5 seconds.
NOTE: To display the program type or rating, press
the TYPE button after selecting the desired program
using the ù (or û) button.
The Timer program menu appears.
If the clock has not yet been set, the Clock set
menu appears.
5 When finished, press the MENU button to exit the
menu.
If necessary, the clock can also be set using the
CHANNEL l (or j) and FF buttons. (Refer to the
next step for button functions.)
6 Press the POWER button.
The VCR power turns off and the timer is set to the
recording standby mode.
2 Use the CHANNEL l (or j) and FF buttons on the
VCR front panel to program the timer.
The Timer icon (n) appears.
CHANNEL button: To select numbers or switch
settings
Clearing the Program Timer
FF button:
To select the next item
1 Follow steps 1 – 4 in “Checking the Program Timer”.
NOTE: If you enter the wrong number or setting,
press the REW button to return to the wrong number
or setting, then enter the correct one.
2 Press the ù (or û) button to select the program to be
cleared.
3 When the recording tape speed is set, press the FF
3 Press the CLEAR button.
button on the front panel to save the settings.
The erase confirmation screen appears.
4 When finished, press the REC button on the front
4 Press the CLEAR button again. (To cancel the erase
procedure, press the SET button.)
panel to exit from the menu.
5 Load a cassette.
The selected timer program is erased from the
program memory.
6 Press the POWER button.
5 When finished, press the MENU button to exit the
NOTES:
menu.
œ Daily or weekly recording, or the program type cannot
6 Press the POWER button.
be set using this method.
œ Once a program timer recording has been set, it cannot
be erased using the buttons on the VCR front panel.
Changing the Program Timer
1 Follow the steps under “Clearing the Program Timer”
to erase the program that you wish to change.
2 Follow the steps under “Timer Programming” to add a
new timer program.
31
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
PROGRAM TIMER RECORDING
Using Timer Recording for Several
Programs
If two or more programmed recording times overlap on
the same day, the VCR will not begin recording a new
program until the previous program has ended (as shown
below).
Program Recording Order
7:00PM
Program
8:00PM
9:00PM
10:00PM
These portions will
not be recorded
TIMER SETTING NOTES:
œ If the programmed recording falls on a Saturday or a
Sunday, the Daily recording mode will not be possible.
œ To select the A/V recording mode, press the INPUT
button instead of selecting a channel number.
œ 12:00 PM = noon; 12:00 AM = midnight.
œ If the end of the tape is reached during timer recording,
the VCR stops and the power turns off automatically.
œ If the power fails or the VCR is unplugged from the
AC outlet, the correct clock time and timer settings
are kept in memory for approximately 5 seconds.
After 5 seconds, the clock and program timer must
be reset when power is restored. Refer to INITIAL
SETUP to set the VCR.
32
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
QUICK TIMER RECORDING (QTR)
As the name suggests, the QTR feature provides a quick
and simple way to set the timer to record. A QTR setting
overrides Program Timer settings.
NOTES:
œ The end time can be advanced for a total of up to
24 hours.
œ The clock must be set before Quick Timer Recording
œ Recording ends if the end of the tape is reached.
can be performed.
œ To stop recording before the end time is reached, press
the STOP button (or STOP/EJECT on the front panel).
œ To set the type of the recording, first follow the steps
under Entering the Program Type on page 26.
œ Start a recording following the instructions for
“RECORDING”, steps 1 – 3 on page 23.
1 Press the REC button during recording.
“--:--” appears on the VCR display.
REC
OFF
2 Set the recording end time using the REC button (to
advance the time in 30-minute increments to the
nearest hour or half hour) or the CH/TRACK l (or j)
button (or CHANNEL on the front panel) (to increase
or decrease the time in 1-minute increments).
Auto Setting
If an XDS-encoded broadcast is being recorded, “AUTO”
appears at step 1 above and blinks for 10 seconds in the
display. The VCR timer receives the end time information
from the XDS signal and the recording continues until the
end of the program.
REC
OFF
Notes on using the AUTO setting
œ To set the recording end time manually, press the REC
button while “AUTO” is blinking. The display will switch
to “--:30” or “--:00”. Then use the REC button
and/or the CH/TRACK l (or j) button to set the
recording end time.
œ Depending on the reception conditions of TV signal or
remaining program duration, the AUTO QTR operation
may not be accurate.
33
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
CHILD LOCK
With the Child Lock function on, the picture is blanked
and the sound muted, virtually blocking the ability to view
a videotape or TV program received through the VCR
tuner.
NOTES:
œ Even when the child lock function is activated, timer
recording and other functions can still operate normally.
œ Since the child lock function can be activated or
deactivated by remote control, you may wish to store
the remote control in a secure location while the child
lock function is activated.
1 Press the MENU button.
The main MENU appears.
2 Press the ù (or û) button to select the VCR setup
option, then press the OK button.
The VCR setup menu appears.
3 Press the ù (or û) button to select the Child Lock
option, then press the > (or <) button to select the
“On” position, as indicated by the “z”.
NOTE: Select the “Off” position to cancel the child
lock function.
4 When finished, press the MENU button to exit the
menu.
While the child lock function is active, the message
“Blocked” will appear on the TV screen.
Ad JUMP®
The Ad JUMP® feature allows you to skip through to the
end of a commercial break at a faster speed and resume
normal playback at the point when the program restarts.
1 During playback, press the Ad JUMP button when a
commercial starts.
Forward picture search begins.
The sound is muted.
2 Press the Ad JUMP or the PLAY button when the
commercial ends.
The tape will rewind for a few seconds, then
playback will resume.
34
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
COPYING A TAPE
You can copy recordings (such as home videos) from one
tape to another using two VCRs.
Audio connection cable
(not supplied)
TV
Video connection cable
(not supplied)
OUT
IN
VIDEO
AUDIO
VIDEO
AUDIO
TO TV
OUT
VCR 1: To play back
VCR 2: To record
1 Connect the VCRs as shown.
6 Press the TV/VCR button on VCR 2 to select the
VCR mode.
2 Insert the recorded cassette into VCR 1.
3 Insert a blank tape into VCR 2.
7 Place VCR 2 in the record/pause mode.
8 Press PLAY on VCR 1.
4 Set the desired recording speed on VCR 2.
9 When the tape in VCR 1 has reached the desired
point, press (release) PAUSE/STILL on VCR 2.
Recording begins.
5 Turn on the TV and set it to channel 3 or 4.
If you use this model as VCR 2 to record:
œ Press the INPUT button on VCR 2 to select the rear
F Press STOP (or STOP/EJECT on the front panel) on
input jacks.
both VCRs when finished.
The AV indicator “L1” is displayed instead of a channel
number.
MAINTENANCE
Head Care and Cleaning
Cabinet Cleaning
œ This VCR has a built-in automatic head cleaner. Under
normal conditions, the heads should not require
additional cleaning. If you suspect a problem, contact a
factory-authorized service center.
œ Clean the outside of the cabinet with a clean, soft cloth,
moistened with lukewarm water and wrung dry.
DO NOT USE SOLVENTS OR OTHER TYPES OF CLEANSERS. THESE CHEMICALS CAN CRACK OR
DISCOLOR THE CABINET.
35
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
TROUBLESHOOTING GUIDE
If you have followed the instructions in this manual and still have difficulty operating your VCR, check the steps below
before getting help from a factory-authorized service center.
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
No power.
œ The power cord is not connected.
œ Connect the power cord to the AC
power input socket, then to an AC wall
outlet.
œ The power is not on.
œ Turn the power on.
The “Auto Setup” message is
displayed when the power is
turned on.
œ The VCR is being used for the first
time or after the power has failed or
has been disconnected for more than
5 seconds.
œ The VCR is not set or the settings
have been erased from the memory.
Please refer to INITIAL SETUP to set
the VCR.
Timer recording does not
function.
œ The clock is not set correctly.
œ The program timer is set incorrectly.
œ The timer is not set to ON.
œ Set the clock correctly.
œ Set the program timer correctly.
œ Turn the power off. The timer icon (n)
appears.
Recording is not possible.
œ The record safety tab on the cassette
œ Place vinyl tape over the safety tab
is missing.
hole in the cassette.
œ The channel selected on the VCR
does not correspond to the cable
converter/decoder output channel.
œ Select the correct channel
(CH 02 ~ 07).
The picture is poor during
playback.
œ The TV channel selector is not set to
œ During playback, set the TV’s channel
selector to channel 3 or 4 to match the
VCR’s channel switch setting.
the proper channel.
œ The TV fine tuning is not set correctly.
œ Fine-tune the TV.
œ If the playback picture is still poor,
contact a factory-authorized service
center.
White lines (noise bands) in
the picture during playback.
œ Poor quality recording or tape.
œ Try a different tape.
No picture during playback.
œ The TV is not set to the proper channel. œ Set the TV’s channel selector to match
the VCR’s channel switch setting
(channel 3 or 4).
Playback picture is partially
noisy. (horizontal white lines)
œ The tracking control is not set to the
œ Adjust the tracking control for a better
proper position.
picture.
TV programs cannot be seen. œ The cable connections are incorrect.
œ Recheck all cable connections.
36
SC4/UF (FVH-E420 GB) Wed. Jan. 26/2000
SPECIFICATIONS
General Specifications
Television system
Recording system
Number of heads
Format
NTSC standard system
Rotary helical scan system
4, Double azimuth video
VHS standard
Tape width
1/2 inch
Tape speed
SP : 33.35 mm/sec. (1.31″/sec.)
LP : 16.67 mm/sec. (0.65″/sec.) ..... (playback only)
SLP : 11.12 mm/sec. (0.43″/sec.)
Recording time
SP : 120 minutes with T-120 cassette
SLP : 360 minutes with T-120 cassette
SLP : 480 minutes with T-160 cassette
Tuner receivable channels
(181 total)
TV Position
VHF channels
UHF channels
CATV Position
VHF channels
Mid band channels
Super band channels
Hyper band channels
Mid low band channels
2-13
14-69
1-13
14-22
23-36
37-94, 100-125
95-99
RF converter
Converter output
Time indication
Timer
Built-in VHF converter
Channel 3 or 4 selectable
AM/PM 12-hour system
1 year/8-event programmable
Terminals
Antenna input
VHF/UHF: F type
VHF/UHF: F type
RCA jack
Antenna output
Video input/output
Audio input/output
RCA jack
Electrical Specifications
Video output level/impedance
Audio output level/impedance
Video input level/impedance
Audio input level/impedance
1 V(p-p)/75 ohms
316 mV (–10 dBV)/less than 2.2 kohms
500 mV(p-p) – 2.0 V(p-p)/75 ohms
316 mV (–10 dBV)/more than 47 kohms
Other Specifications
Power requirements
Power consumption
Dimensions (W x H x D)
Weight (approximate)
Remote control
120 V AC, 60 Hz
14 watts
360 mm x 97 mm x 275 mm (14.17″ x 3.82″ x 10.83″)
3.0 kg (6.6 lbs.)
B24605
The manufacturer reserves the right to modify product designs and specifications without notice and without incurring
any obligation.
®
21605 Plummer Street,
Chatsworth, California 91311
1AC6P1P2254– –
SC4/UF
(0300KP-SJC)
Issue No. 1
Copyright FISHER, 2000 All rights reserved.
Printed in Indonesia
37
|