™
Instructions
Model Number: 72639
Please keep this instruction sheet for future reference, as it contains important information.
Adult assembly is required.
Tools needed for assembly: Hammer, Phillips Screwdriver, Scrap Block of Wood (tools not included).
If you have any questions about this product, or are missing a part, please call us toll-free
at 1-800-432-KIDS, rather than return this product to the store.
Age: 2 - 5 years.
Weight Limit: 55 lbs.
Assembly
Frame
Hole
3
1
Hole
Straight Axle
Straight Axle
Bottom View
• Turn the frame upside down.
• Insert the straight axle through the holes in the rear of
the frame.
Cap Nut
Scrap Block
of Wood
Rear Wheel
Indented Side Up
4
Cap Nut
Hubcap Peg
Side Down
• Place a cap nut on a scrap block of wood.
• Place one end of the straight axle into the cap nut.
• Tap the end of the straight axle with a hammer.
Make sure the cap nut is securely attached to the
straight axle.
Washer
Straight Axle
Frame
Straight Axle
2
Washer
Assembled Rear
Wheel
Scrap Block
of Wood
Bottom View
• Turn the frame on its side with the exposed end of
the straight axle up.
• Place the assembled rear wheel on the scrap block
Hubcap Peg
Side Up
Rear Wheel Indented
Side Down
of wood.
• Slide a washer onto the straight axle.
• Slide a rear wheel (indented side up) onto the end of
the straight axle.
• Slide a hubcap (peg side down) onto the straight axle.
• Fit a cap nut on the end of the straight axle.
• Tap the cap nut with a hammer. Gently pull the rear
wheel up to be sure the cap nut is securely
attached to the straight axle.
• Slide a hubcap (peg side up) onto the straight axle.
• Slide a rear wheel (indented side down) onto the
straight axle.
• Slide a washer onto the straight axle.
• Set the frame assembly aside.
3
Assembly
Pedal Hub
Pedal Axle
8
5
Pedal Axle
Metal Tab
Pedal Hub
Slot
Pedal Hub
• Turn the front wheel assembly over.
• Insert a pedal hub onto the top of the pedal axle and
into the hole in the center of the front wheel.
• Insert the remaining pedal hub below the pedal axle
• Fit two pedal hubs onto the pedal axle metal tabs. Make
sure the metal tabs fit into the slot in each pedal hub.
and into the hole in the center of the front wheel.
Pedal Hubs
6
Pedal Hubs
9
Pedal Axle
Front Wheel
Hole
• Push the pedal hubs into the center of the front wheel
until they are flush with the surface of the front wheel.
• While holding the pedal hubs on the pedal axle,
insert the pedal axle into the hole in the center of the
front wheel.
10
7
Pedal Hubs
Pedal
Pedal Axle
Front Wheel
Assembly
• Push the pedal hubs into the center of the front wheel
until they are flush with the surface of the front wheel.
Scrap Block
of Wood
• Place a scrap block of wood under the front
wheel assembly.
• Fit a pedal on the pedal axle.
• Tap the pedal with a hammer until it is secure.
• Repeat this procedure to attach the other pedal to the
other end of the pedal axle.
Fisher-Price, Inc., a subsidiary of Mattel, Inc.
East Aurora, New York 14052, U.S.A.
© 2001 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
BARBIE is a U. S. trademark of Mattel, Inc.
Printed in Mexico
72639c-0920
4
Assembly
Pegs
Fork Arms
Front Wheel Assembly
Fork Cover
11
13
Seat
Holes
Groove
3
4
#8 x / " Screw – 4
Pedal Axle
SHOWN ACTUAL SIZE
• Place the front wheel assembly between the fork arms
so that the pedal axle fits into the groove at the bottom
of each fork arm.
• Place a fork cover over the pedal axle on one fork arm.
• At an angle, insert one peg on the back of the seat into
the hole in the rear of the frame.
• Insert and "snap" the other peg on the back of the
seat into the other hole in the rear of the frame.
3
4
• Insert two #8 x / " screws into the fork cover and
tighten with a Phillips screwdriver. Do not over-tighten.
• Repeat this procedure to attach the other fork cover
to the other fork arm.
One-time assembly is now complete.
Handlebar
12
Frame Neck
Fork Post
Fork Cover
#8 x 3" Screw – 1
SHOWN ACTUAL SIZE
• Turn the frame upright.
• Insert the fork post up through the hole in the neck of
the frame. Make sure the fork is positioned so that
the fork covers face the rear wheels.
• Place the handlebar over the fork post and push it
down onto the frame. Make sure the handlebar is
positioned so that the screw hole faces the rear
wheels and aligns with the screw hole in the fork post.
Hint: You may need to rotate the handlebar to align
the holes.
• Insert the #8 x 3" screw through the hole in the han-
dlebar and into the fork post. Tighten the screw with
a Phillips screwdriver. Do not over-tighten.
5
Label Decoration
Maintenance
• Check plastic parts regularly and if broken or cracked,
dispose of them properly.
Proper label application will help to keep the labels
looking their best!
• Check all fasteners regularly to be sure they are tight.
If the fasteners are not tight, tighten them as neces-
sary.
• To clean the trike, use a mild soap and water solution
and a clean cloth. Rinse clean with water to remove
soap residue.
• Wash your hands before applying the labels.
• Make sure the areas where the labels will be applied
are clean and dry. Wipe your vehicle with a clean, soft,
dry cloth to remove any dust or oils.
• For best results, avoid applying a label more than once.
• Apply the labels as shown in the illustrations below.
• After applying a label, rub the label firmly with a cloth to
make sure the label is adhered to your vehicle.
Consumer Information
Questions? We'd like to hear from you!
Call Fisher-Price® Consumer Relations, toll-free at
1-800-432-KIDS, 8 AM - 6 PM EST Monday
through Friday. Hearing-impaired consumers using
TTY/TDD equipment, please call 1-800-382-7470.
Or, write to: Fisher-Price® Consumer Relations,
636 Girard Avenue, East Aurora, New York 14052.
5
7
2
For other countries, outside the United States:
Canada: Call 1-800-567-7724, or write to: Mattel Canada Inc.,
6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
Great Britain: telephone 01628 500303.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
6
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
4
Right Side
8
1
6
3
Left Side
|