Installation Guide
VSW I AAP
Remote Input and Control Panel
68-1187-01 Rev. B
03 07
Rear panel features
1
2
Figure 2 — Rear panel features
Audio pass-through — Output unbalanced stereo audio through
this 3.5 mm mini audio jack. See the previous section's wiring
a
diagram ( ).
b
Computer video pass-through — Output VGA-UXGA, RGBHV,
RGBS, RGsB, RsGsBs, component video, or HDTV component
video through this 15-pin female VGA connector.
b
Interfacing to SW VGA Series Switchers
The VSW I AAP can be connected to each input of a SW VGArs switcher.
Pressing the Show Me button causes the switcher to select this input.
Refer to the SW VGArs Switchers manual for connection instructions.
Projector
SHOW ME
SHOW ME
SHOW ME
AUDIO
AUDIO
AUDIO
VSW
I
AAP
VSW
I
AAP
VSW I AAP
COMPUTER
COMPUTER
COMPUTER
VSW I
AAP
VSW I
AAP
VSW I
AAP
100-240V 0.2A
REMOTE
INPUTS
SW6VGAArs
OUTPUT
1
2
3
5
OUTPUT
L
R
4
6
50-60Hz
SW6 VGA Ars
SHOW ME
SHOW ME
SHOW ME
AUDIO
AUDIO
AUDIO
VSW
I
AAP
VSW
I
AAP
VSW I AAP
COMPUTER
COMPUTER
COMPUTER
VSW I
AAP
VSW I
AAP
VSW I
AAP
Figure 3 — Multiple VSW I AAP inputs to an SW VGArs
switcher
VSW I AAP • Installation and Operation
2
Interfacing
Interfacing to a VSW 2VGA A Daisy Chain
VSW 2VGA A switchers can be daisy chained together to form a
presentation system (figure 4). Each switcher connects to a VSW I AAP.
By pressing the AAP's Show Me button, the user sends a control signal
telling the switcher to select this AAP as the active input. Refer to the
VSW 2VGA A Switchers manual for connection instructions.
Extron
VSW I AAP
Extron
VSW 2VGA A
VGA Switcher
SHOW ME
AUDIO
VSW I AAP
COMPUTER
Expandable, economical presentation chain for
conference rooms and library study rooms.
Extron
VSW I AAP
Projector
SHOW ME
SHOW ME
SHOW ME
Extron’s pre-made
VGA with audio cable
assemblies.
AUDIO
AUDIO
AUDIO
COMPUTER
VSW
I
AAP
COMPUTER
VSW
I
AAP
COMPUTER
VSW AAP
I
VSW I
AAP
VSW I
AAP
VSW I
AAP
In 1
In 1
In 1
INPUT
1
INPUT
2
INPUT
1
INPUT
2
INPUT
1
INPUT
2
INPUT
1
INPUT
2
In 2
In 2
In 2
Out
Out
Out
1
2
1
2
1
2
1
2
VSW 2VGA
A
VSW 2VGA
A
VSW 2VGA
A
VSW 2VGA
A
VSW 2VGA A
VSW 2VGA A
VSW 2VGA A
Extron’s pre-made VGA with audio cable assemblies.
Figure 4 — Daisy-chained VSW 2VGA A switchers
VSW I AAP • Installation and Operation
3
Configuration
Setting VSW I AAP Jumpers
A jumper (figure 5) on the VSW I AAP may need to be shifted, from
jumper J6 (the default position) to J5, depending on the switcher to
which the VSW is connected. Refer to the applicable switcher’s manual
to see how to determine the switcher’s board version or level.
J5
J6
Jumper installed Switcher compatibility
J6
VSW 2VGA A, board revision C
SW VGArs, board part #20-1118-0x
VSW 2VGA A, board revision A
J5
Figure 5 — VSW I AAP jumper positions
• If you are daisy chaining with a VSW 2VGA A that has a circuit board
that is revision C or higher, install the jumper on J6.
• If you are daisy chaining with a VSW 2VGA A that has a circuit board
that is revision A, install the jumper on J5.
• If you are daisy chaining with a SW VGArs that has a circuit board
whose part number is 20-1118-0x, install the jumper on J6.
The show me feature will not work when connected to
SW VGArs series switchers with a circuit board part number of
20-527-0x or 20-935-0x.
N
4
VSW I AAP • Installation and Operation
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
800.633.9876 714.491.1500
FAX 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort, The Netherlands
+800.3987.6673 +31.33.453.4040
FAX +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Rd. #04-01
PM Industrial Bldg., Singapore 368363
+800.7339.8766 +65.6383.4400
FAX +65.6383.4664
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
+81.3.3511.7655 FAX +81.3.3511.7656
© 2007 Extron Electronics. All rights reserved.
|