EverPlex 4BQ
USER'S MANUAL
Real time B/W quad processor
High resolution picture quality
4 Alarm input with buzzer
Table of Content
Safety Warning...........................................................................................................1
Introduction................................................................................................................2
Specification...............................................................................................................3
Chapter I Front Panel Keypads.....................................................................4
1. Full Screen.........................................................................................................4
2. Quad Display .....................................................................................................4
3. Sequential Seitching ..........................................................................................4
4. VCR Playback……….. .....................................................................................4
Chapter II Back Panel Function......................................................................5
1. BNC Connectors................................................................................................5
1.1 Video In.........................................................................................................5
1.2 Video Out ......................................................................................................5
1.3 Monitor .........................................................................................................5
1.4 VCR out ........................................................................................................5
1.5 VCR In ......................................................................................................5
2. Level
.........................................................................................................5
3. Terminator On/off..............................................................................................5
4. Alarm time.........................................................................................................6
5. Switch Time.......................................................................................................6
6. VCR Level.........................................................................................................6
7. Power
.........................................................................................................6
8. Alarm Connectors (DB-15) ...............................................................................6
8.1 Alarm out ......................................................................................................7
8.1.1 Normally Open Connection ................................................................7
8.1.2 Normally Closed Connection..............................................................7
8.2 Alarm in ........................................................................................................8
1
Safety Warning
1. To prevent fire or shock hazard, do not expose this equipment to the
environment of high humidity and dust. Do not use it in an unprotected
outdoor installation or any area classified as a wet area.
2. Installation environment: The temperature should be kept between 0oC ~
+50oC
3. For safety sake, do not disseminate the unit or put it on an unstable base.
4. Ventilation: Openings in the enclosure are provided for ventilation and to
ensure reliable operation of the unit and to protect it from overheating. These
openings must not be blocked or covered. This unit should not be placed in a
built-in installation unless proper ventilation is provided.
5. Cleanse: Unplug the unit from the outlet before cleansing. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth to clean it.
6. Overload: Do not overload outlets and extension cords as this may result in a
risk of fire or electric shock.
7. Power-cord Protection: Power-supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
8. Object and Liquid Entry: Never push objects of any kind into this unit through
openings as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind on the
unit.
9. Service: Do not attempt to service this unit yourself as opening or removing
covers may expose you to dangerous voltage of other hazards. Refer all
servicing to qualified service personnel.
2
Introduction
This B/W Quad processor represents the best choice for 4 cameras monitoring
and recording. 4 channel auto sequential switching with real time quad display,
superior high resolution, and the most practical features in one convenient unit.
The most unbeatable B/W Quad processor for the security surveillance.
Main Features:
‰ Connect up to 4 cameras with loop through
‰ Real-time quad display
‰ Option to watch full image or quadrant pictures
‰ Superior high resolution:960 x 576 (CCIR) , 960 x 480 (EIA)
‰ Independent brightness level adjustment for each channel and VCR output
‰ Auto sequential switching for each camera and quad (Dwelling time: 1~10
seconds)
‰ Alarm time setting (1-20 seconds)
‰ 4 alarm inputs with built-in buzzer
‰ VCR playback function
‰ Easy-handled desktop size
‰ User-friendly front panel design
‰ Low power consumption
3
Specification
Video input:
Up to 4 cameras inputs and 1 VCR input
Video output:
1 monitor output and 1 quad output for VCR
1Vp-p/75 ohm
Refresh Rate:
15~30 fields/sec.
Yes
VCR Playback:
Alarm input:
Buzzer:
4 alarm inputs and 1 alarm reset input
Yes
Alarm output:
Dimension:
2 Alarm Out (1 Normally Open, 1 Normally Closed)
239 x 166 x 55 mm
AC 24V
Power source:
Power consumption:
5W max.
Operating temperature: 0°C to +50 °C
4
Chapter I Front Panel Keypads
1. Front Panel Keypads
Seq
1.1 Full Screen
Press any key of corresponding quadrant, the required channel will be displayed as full
screen on the monitor. Press
to go back to quad display.
1.2 Quad Display
Press
, the 4 camera input will be displayed in quad format on the main monitor.
1.3 Sequential Switching
Press Seq key to enter the auto sequential switching mode. It will display live quad and full
screen sequentially on the main monitor. Press any full screen key or quad display key to
exit Seq mode.
1.4 VCR Playback
Press
key to play back the recorded video from VCR. Press any full screen key or quad
display key to exit Seq mode.
5
Chapter II Back Panel Function
1. BNC Connectors
1.1 Video In
Connect camera video output to the corresponding video in connector by a 75 ohm
coaxial cable.
1.2 Video Out
Connect the other devices to these connectors. They are used to loop through
camera’s video to other devices.
1.3 Monitor
Connect this output port to the main monitor.
1.4 VCR Out
Connect this output port to the VIDEO IN of VCR. The quad video output is obtained
from this connector.
1.5 VCR In
Connect this input port to the VIDEO OUT of VCR.
2. Level
The 4 gain control regulators is used to adjust the brightness level of the video input.
3. Terminator On/Off
Terminator Camera Input
OFF
ON
ON
1
2
3
4
1
2
3
4
Not Terminated 75 Ohm Termination
Not Terminated 75 Ohm Termination
Not Terminated 75 Ohm Termination
Not Terminated 75 Ohm Termination
1
2
3
4
Each camera should be terminated by 75 Ohms. This termination is normally
provided by having all switches of 1-4 on. If cameras are looped through to other
equipment which provides termination, then the switch sections of the corresponding
inputs should be turned off.
6
4. Alarm Time
Adjust the alarm holding time from 1 to 20 seconds.
5. Switch Time
Adjust the auto sequential switching time from 1 to 10 seconds.
6. VCR Level
The gain control regulator is used to adjust the brightness level of the VCR output.
AC24V
7. Power
Connect the AC 24V power source to the power input
terminals. The power supply connection is illustrated
as the right sketch.
+
AC 24V Adapter
+
8
1
8. Alarm Connectors (DB-15)
9
15
NAME
PIN # NAME
PIN #
9
1
2
3
4
5
6
7
8
Alarm Out Common contact
Alarm Out Normally Closed
Alarm Reset
Alarm Out Normally Open
10
11
GROUND
12
ALARM IN 1
ALARM IN 2
ALARM IN 3
ALARM IN 4
ALARM OUT
13
14
15
7
8.1 Alarm out
There are two ways to do the alarm out connection:
8.1.1 Normally Open Connection (use pin # 1 and # 9)
2
1
8
RELAY
Alarm out
15
9
4 Channel B/W Quad
8.1.2 Normally Closed Connection (use pin # 1 and # 2)
2
1
8
RELAY
Alarm out
15
9
4 Channel B/W Quad
8
8.2 Alarm in
There are 4 alarm sensors in for 4 channels, all these alarm inputs are
Normally Open and shorted to ground means an alarm happens.
ALARM
CIRCUIT
2
1
8
SENSOR 4
SENSOR 3
SENSOR 2
SENSOR 1
15
9
There are four alarm inputs for each camera. Please connect the alarm input in the same
sequence as the cameras input.
When any alarm signal is input, this quad processor will do the following:
1. switch to the full screen display of the alarmed channel.
2. Light on the channel LED.
3. turn on the buzzer.
When 2 or more alarms occur from the cameras, it will switch to quad display.
When the alarm time is over, it will go back to the normal condition that alarm
occurred before.
EverFocus Electronics Corp.
Hong Kong Office:
Head Office:
Room 0, 10/F., Block 3, Camelpaint Building,
60, Hoi Yuen Road, Kwun Tong, Kowloon
Hong Kong
10F-6, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chi, Taipei, Taiwan
TEL: 886-2-26982334
FAX: 886-2-26982380
TEL: 852-2758-9871
FAX: 852-2758-9056
European Office:
USA Office:
Fasanenweg 3, D-46446 Emmerich
Germany
TEL: 49-2822-9394-0
FAX: 49-2822-939495
145 Vista Ave. Suite 108
Pasadena, CA. 91107
USA
TEL: 1-626-844-8888
FAX: 1-626-844-8838
Toll free: 1-888-383-6287 or
1-888-EV-FOCUS
P/N : M4BQG00100
|