EQH5102 1080p Mini Box Camera
User’s Manual
** Lens not included.
Copyright © EverFocus Electronics Corp,
Release Date: July, 2012
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
ATTENTION! This is a class A product which may cause radio interference in a domestic
environment; in this case, the user may be urged to take adequate measures.
This Product is RoHS compliant.
Your EverFocus product is designed and manufactured with high quality materials and
components which can be recycled and reused. This symbol means that electrical and
electronic equipment, at their end-of-life, should be disposed of separately from your
household waste. Please, dispose of this equipment at your local community waste
collection/recycling centre. In the European Union there are separate collection systems for
WEEE
used electrical and electronic product.
Please, help us to conserve the environment we live in!
ii
Contents
1. INTRODUCTION ........................................................................................ 1
1.1 PACKING LIST .............................................................................................................. 1
1.2 FEATURES .................................................................................................................. 1
2. OVERVIEW ............................................................................................... 2
3. INSTALLATION .......................................................................................... 2
3.1 LENS INSTALLATION AND ADJUSTMENT .............................................................................. 2
3.2 TOP / BOTTOM-MOUNT ............................................................................................... 3
4. BASIC CONNECTION .................................................................................. 3
5. CONFIGURATION IN THE OSD MENU.......................................................... 3
5.1.1 EXPOSURE.............................................................................................................................. 4
6. SPECIFICATIONS .................................................................................... 10
7. APPENDIX ............................................................................................. 11
7.1 OSD MENU STRUCTURE............................................................................................... 11
iii
EQH5102 1080p Mini Box
Camera
1. Introduction
The EQH5102 is an HDcctv indoor mini box camera. Based on a progressive scan CMOS sensor for
HD 1080p resolution 100% digital images, it delivers vastly superior video quality compared to
traditional CCTV images. This superior resolution not only captures more critical evidentiary
information, but the inherent ability for megapixel video also extends the area of coverage,
expedites completion of investigations, resolves complaints and reduces both capital and
operational costs.
No major upgrade to the IT network is required to deploy this powerful technology; HDcctv
cameras communicate at digital speeds up to 1.5 Gb/s over existing or new coaxial cable (RG59 or
other types for longer distances), using industry standard BNC connectors.
The EQH5102 allows flexible choices of megapixel manual & DC iris control lenses with C / CS
mount for outstanding coverage in a wide range of demanding surveillance environments while
delivering stunning HD image quality.
1.1 Packing List
•
•
•
Camera body x 1
Power Pigtail Cable x 1
User Manual x 1
•
•
Lens Cover x1
C-mount lens adapter x 1
1.2 Features
• Real time HDcctv 1080p HD video over coax for superlative image detail
• 1/3” 2.1 megapixel Color Progressive CMOS sensor
• CS/C mount, manual and DC iris control for flexible choice of HD Megapixel lenses
• Provides 3D DNR/ DSS to improve image clarity, particularly in low light scenes
• Electronic Lens Shading Compensation to offset diminished light transmission through lens
periphery for uniform image illumination
• CTB [Contrast Boost] to deliver properly exposed images despite bright light sources, deep
shadows and/or unbalanced lighting in the same scene
• Supports Digital Zoom/ BLC [Back Light Compensation]/ HSMASK [Highlight Suppression
Mask]/ Privacy Zones (up to 32)
• DPC [Defect Pixel Correction] Dead pixel compensation for increased clarity and extended
service life
• SD TV Out for aim and focus using a standard hand held test monitor
1
EQH5102 1080p Mini Box Camera
2. Overview
No. Name
Descriptions
Connects to a HD device using a 75 Ohm BNC-type
coaxial cable.
1
2
3
HDcctv Output
Use the joystick to configure the settings in the OSD
menu.
OSD Menu Joystick
Screwless Terminal Strip
Connects to a 12VDC power, RS-485 and MD (Motion
Detect) source.
4
5
Power LED
Glows red then power is present.
Grounding Stud
Ensuring a good grounding when used.
Connects to a SD CVBS monitor for setting image aim and
focus.
6
Test-Out
3. Installation
3.1 Lens Installation and Adjustment
You can install either a CS-mount or a C-mount lens into the camera. It is recommended to use
a lens with aperture ratio of F/1.2 or lower. Please refer to the following reference steps.
CS-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Adjust the lens using the Focus / Zoom Screws.
2
EQH5102 1080p Mini Box Camera
If you are using a DC Auto Iris lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Connect the DC cable to the DC Auto Iris Lens Connector.
4. Lock the Focus Screw.
C-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body using the supplied C-mount lens adapter.
3. Adjust the lens using the Focus / Zoom Screws.
Warning: Installing a C-mount lens without the C-mount lens adapter may damage the
camera sensor.
3.2 Top / Bottom-Mount
You can use a mounting bracket and screw it on the top of the camera body to suspend the
camera, or on the bottom of the camera body to support the camera.
4. Basic Connection
1. Connect the camera to an HD device, such as an HDcctv DVR, to display the image.
2. Connect the camera to a 12VDC power source using the supplied Power Cable. You can
optionally use the supplied Power Pigtail Cable or a power adapter to connect the Power Cable
to the power source. The power LED will be lit in red.
3. Connect the camera to a CVBS portable monitor for setting image aim and focus before
mounting the camera.
5. Configuration in the OSD Menu
You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD
menu. For details on the OSD menu structure, see OSD Menu Structure in Appendix.
3
EQH5102 1080p Mini Box Camera
5.1 OSD Menu
Press the Enter / Confirm button on the Joystick. The Setup Menu in the OSD appears.
5.1.1 EXPOSURE
Press the Enter / Confirm button to enter the submenu.
BRIGHTNESS
Use the and buttons to increase or decrease the screen brightness from 0 to 20.
MODE
Indoor
Select this mode when the color temperature of the video image is similar to that found in
indoor environments (around 5100 to 5300°K).
Outdoor
Select this mode when the color temperature of the video image is similar to that found in
outdoor environments (around 3,000°K to 3,200°K)
LENS
You can select the type of the lens. Two types are available: Manual and DC. By default, the
DC type lens is selected.
4
EQH5102 1080p Mini Box Camera
Shutter
Use the and buttons to adjust the shutter speed. The options include: 1/25 ~ 1/60000,
FLK, and AUTO. Any selection other than AUTO and 1/25 will disable the DSS function.
DSS (Digital Slow Shutter)
DSS is used to maintain a vivid screen image by automatically boosting low light levels. The
value is between x2 ~ X4 and OFF.
AGC (Auto Gain Control)
The higher the AGC value, the brighter the screen, but the level of noise will also be increased.
The options include: 0~10.
5.1.2 COLOR
Press the Enter / Confirm button to enter the submenu.
AWB (Auto White Balance)
This mode can be used to view areas with a color temperature range. Use the and
buttons to select the AWB options. The options include: AUTO, AUTO EXTN, PRESET, MANUAL
COLOR TEMP, R-GAIN and B-GAIN.
• AUTO – Around 2500 to 9500°K
• AUTO EXTN (Extension) – Around 2300 to 10800°K
• PRESET – Use a pure white background to preset the white balance value.
• MANUAL COLOR TEMP – Use the and buttons to adjust the speed. The options
include: LOW, MIDDLE and HIGH
• R-GAIN and B-GAIN –The options include: 0~20.
CHROMA
Use the and buttons to increase or decrease the CHROMA from 0 to 20.
R-OFFSET/B-OFFSET
Use the and buttons to increase or decrease the Red and Blue offset from 0 to 20.
5
EQH5102 1080p Mini Box Camera
5.1.3 IMAGE
Press the Enter / Confirm button to enter the submenu.
SHARPNESS
Use the and buttons to increase or decrease the SHARPNESS from 0 to 10.
MIRROR/FLIP
Turn it on to reverse/ flip the image.
DZOOM
Turn it on to set up the zoom level
PRIVACY
Enter the submenu to set up the privacy masks; up to 31 zones can be created:
ON ZONE NO: Use the and buttons to select the zone from 0 to 31.
X, Y-POS, SIZ: Enter the submenu to set up the position or size of the privacy mask zone.
COLOR: Press to select a color for the selected privacy mask zone.
TRANS: Press to select the transparency of mask zone.
SHADING
Turn it on to offset diminished light transmission through lens periphery for uniform image
6
EQH5102 1080p Mini Box Camera
illumination.
DAY&NIGHT
The options include MODE, AGC THRS, DELAY. A submenu can be entered if you select MODE.
• MODE – Use the and buttons to select AUTO, COLOR and B&W. Switches to a B&W
feed in low light conditions and then switches back to a Color feed in the daytime.
• AGC THRS –Use the and buttons to select the AGC Threshold from 0 to 20.
• DELAY – Set up the delay time in 0,5,10 and 30 seconds for the camera to switch between
Day and Night.
HLMASK
Turn it on to select the level and color of the masking effect.
CTB (Contrast Boost)
Turn it on to deliver properly exposed images despite bright light sources, deep shadows
and/or unbalanced lighting in the same scene.
GAMMA
Use the and buttons to increase or decrease the GAMMA from 0.45 to 0.75.
5.1.4 BLC
Press the Enter / Confirm button to enter the submenu.
MODE
7
EQH5102 1080p Mini Box Camera
Use the and buttons to select OFF and BLC.
BLC OSD, POS and SIZ
Select OFF to disable the BLC function, or select ON to enable the BLC function and for further
setup. After selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION”
sign displayed on the screen. Use the direction buttons to move the area to the desired
position. Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on
the screen. Use the direction buttons to adjust the size for the area.
5.1.5 3D-DNR
Press the Enter / Confirm button to enter the submenu.
Switch to HIGH, MIDDLE, LOW and OFF to enable or disable noise reduction on dynamic
recordings.
5.1.6 MOTION
Press the Enter / Confirm button to enter the submenu.
8
EQH5102 1080p Mini Box Camera
RESOLUTION
Use the and buttons to increase or decrease the RESOLUTION level from 0 to 4.
SENSITIVITY
Press to set up the sensitivity for the motion detection function.
WINDOW TRANS
Press to select the transparency of motion detect zone.
WINDOW USE, POS and SIZ
Select OFF to disable this function, or select ON to enable and for further setup. After
selecting an area block, enter the BLC POS / SIZ and X/ Y setup page, a “POSITION” sign
displayed on the screen. Use the direction buttons to move the area to the desired position.
Press the Enter / Confirm button to confirm the position, a “SIZE” sign displayed on the screen.
Use the direction buttons to adjust the size for the area.
5.1.7 SYSTEM
Press the Enter / Confirm button to enter the submenu.
DEFECT DET
Press to select the DPC (Defective Pixel Correction) level of defect detector. Please notice; do
not use this function without cover the lens. The camera will automatically correct pixel
defects. Misoperation will cause the abnormal image.
9
EQH5102 1080p Mini Box Camera
CAM TITLE
Switch to On and then enter the submenu to set up a camera name displayed on the screen.
RS-485
Use the and buttons to select ID, BAUDRATE, PROTOCOL and ID DISPLAY. The default of
protocol is EVF-1 (EverFocus).
Version
Press to display the firmware version of the camera.
DOUT
There are 4 options including 1080p 30FPS NTSC, 1080p 25FPS PAL, 720p 60FPS NTSC and
720p 50FPS PAL
Language
Select a language for the OSD text. Options include English, French, German, Simplified
Chinese, Korean and Japanese.
6. Specifications
Camera
Pickup Device
Image Pixels
Resolution
1/3” Panasonic 2.1 megapixel Color Progressive CMOS sensor
1920(H) x 1080(V)
Digital:1080p(30/25), 720p(60/50)
Color: 0.4 lux, BW: 0.1 lux,
Sensitivity
Color DSS: 0.1 lux, BW DSS: 0.025 lux
Digital(HDcctv Output): BT.1120, HDcctv/HD-SDI: BNC connector
Analogue(Test Out): NTSC/PAL CVBS(w/o WDR): BNC connector
More than 50 dB (AGC OFF)
Video Output
S/N Ratio
Lens
DC/Manual
AGC
0-20 steps
Shutter Speed
AUTO/MANUAL(1/25(30)~1/60,000sec)
10
EQH5102 1080p Mini Box Camera
Digital Slow Shutter(DSS)
Brightness
On/Off(x4)
0-20
BLC
On/Off
Contrast Boost(CTB)
Day&Night
On/Off
Auto/Color/B&W
Auto/Auto extn/Preset/Manual
Auto White Balance
Digital Noise Reduction(DNR) Off/Low/Middle/High
Mirror
On/Off
Flip
On/Off
Sharpness
0 - 10 steps
On/Off
Lens Shading Compensation
Digital Zoom
Privacy Mask
Motion Detection
0 - 96 steps
32 Zones, Programmable
On/Off（Swith Output, Screwless terminal connector）
2400~115200> baud, ID 1~255, Protocols: Pelco-D/P, EverFocus
EVF-1; Screwless terminal connector
RS - 485
Language
English/French/German/Simplified Chinese/Japanese
12VDC, Screwless terminal connector
12VDC: 2W max.
Power Source
Power Comsumption
Operating Environment
Dimensions(L x W x H)
Weight
0°C~45°C/32°F~113°F (20%~80% Humidity)
89 x 46 x 48mm /3.5” x1.8” x1.9”
0.193kg/0.434lbs
Certifications
FCC / CE
7. Appendix
7.1 OSD Menu Structure
The default value is marked with a star “*”.
No
Main
Sub Menu
Sub Menu / Function
.
1
EXPOSURE BRIGHTNESS
1~20 (default=6)
INDOOR*, OUTDOOR
MANUAL, DC*
MODE
LENS
11
EQH5102 1080p Mini Box Camera
AUTO*
SHUTTER
MANUAL
1/25~1/60000
FLK
DSS
OFF, X2, X3, X4*
0~10 (default=10)
AUTO*
AGC
AUTO extn
PRESET
AWB
MANUAL COLOR TEMP
R-GAIN
LOW, MIDDLE, HIGH
2
3
COLOR
IMAGE
0~20
0~20
B-GAIN
CHROMA
R-OFFSET
B-OFFSET
SHARPNESS
MIRROR
FLIP
0~20 (default=7)
0~20 (default=12)
0~20 (default=5)
0~10 (default=6)
ON, OFF*
ON, OFF*
D-ZOOM
0~96 (default=0)
OFF*
ON ZONE NO
ZONE UP
X-POS
0~31
ON, OFF
0~60
PRIVACY
Y-POS
0~40
X-SIZ
0~60
Y-SIZ
0~40
COLOR
TRANS
0~4
SHADING
ON*, OFF
AUTO*
COLOR
B&W
NODE
DAY&NIGHT
AGC THRS
MARGIN
DELAY
0~20 (default=10)
0~20 (default=)
0, 5*, 10, 30 SEC
OFF*
HLMASK
LEVEL
0~20 (default=10)
ON
COLOR BLK*/WHT/YEL/CYN/GRN/MAG/RED/BLU
12
EQH5102 1080p Mini Box Camera
CTB
ON, OFF*
GAMMA
MODE
0.45*, 0.5, 0.55, 0.65, 0.75
OFF*, BLC
BLC OSD
BLC POS-X
BLC POS-Y
BLC SIZ-X
BLC SIZ-Y
ON, OFF*
0~20 (default=7)
0~20 (default=7)
0~20 (default=5)
0~20 (default=5)
4
5
BLC
3D-DNR
HIGH, MIDDLE*, LOW, OFF
OFF*
RESOLUTION
0~4 (default=1)
0~20 (default=10)
0~6 (default=3)
ON, OFF*
SENSITIVITY
WINDOW TRANS
6
MOTION
WINDOW USE
ON
X-POS
0~60 (default=4)
0~40 (default=6)
0~60 (default=15)
0~40 (default=20)
000~255 (default=26)
Y-POS
X-SIZ
Y-SIZ
DEFECT DET
CAM TITLE
DPC LEVEL
OFF*
STRING SET
ON
POSITION
ID
1~255 (default=1)
BAUDRATE 2400, 4800, 9600*, 19200, 38400, 57600, 115200
PROTOCOL PELCO-D, PELCO-P, EVF-1*
ID DISPLAY ON, OFF
RS-485
7
SYSTEM
DOUT SCALE
DOUT
FULL*, COMP
720P, 1080P*
FORMAT
DOUT FPS
FREQ
50, 60 ,25*, 30
50*, 60 HZ
CVB
PAL*, NTSC
LANGUAGE
RESET
English, Simplified Chinese, Japanese, Korean, French, German
PUSH, PUSHING
13
EverFocus Electronics Corp.
EverFocus Taiwan:
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886 2 2698 2334
TEL: +49 2822 93940
FAX: +886 2 2698 2380
FAX: +49 2822 939495
EverFocus China - Beijing:
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 755 2765 1313
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: +86 10 6297 3336~39
FAX: +86 10 6297 1423
FAX: +86 755 2765 0337
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
EverFocus USA - New York:
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 631 436 5070
TEL: +1 626 844 8888
FAX: +1 631 436 5027
FAX: +1 626 844 8838
EverFocus Japan:
EverFocus Europe - UK:
5F, Kinshicho City Building, 2-13-4
Koto-Bashi,Sumida-Ku, Tokyo, 130-0022, Japan
TEL: +81 3 5625 8188
Unit 12, Spitfire Business Park,
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: +44 20 8649 9757 / +44 845 430 9999
FAX: +44 20 8649 9907
FAX: +81 3 5625 8189
EverFocus India:
Suite 803, Housefin Bhavan, C-21, Bandra Kurla
Complex, Bandra (East), Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunal
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
N
|