EVH-1152D/66
Single 15” Two-Way Coaxial
60° x 60° Full-Range
High-Efficiency
Loudspeaker System
Key Features:
•
•
•
•
DH7N 3” (76 mm) diaphragm, 1.4” (36 mm) exit
pure titanium compression driver
SMX2151 15” (381 mm) LF transducer with fully
symmetric drive
Advanced fourth-order crossover network with
HF protection
Coverage pattern: 60° x 60° Constant
DirectivityTM 12” rotatable waveguide
•
•
•
105 dB sensitivity, 138 dB maximum SPL
System rating: 500 W continuous, 2000 W peak
Active rating: LF 400 W/HF 75 W continuous
(1600 W/300 W peak)
Technical Specifications:
•
•
(28) M10 threaded suspension points
PI and FG versions available with gland nut and
stainless-steel grille
Freq. Response1 (-3 dB): 60 Hz - 17 kHz
Freq. Range1 (-10 dB): 50 Hz - 20 kHz
Rotatable Coverage: 60° x 60°
Rec. High-Pass Frequency: 60 Hz
General Description:
Passive Crossover Freq.: 1300 Hz
Axial Sensitivity1: 105 dB (1 W/1 m)
The Electro-Voice EVH-1152D/66 is a high-power, two-way horn-loaded
coaxial loudspeaker system that can be used in a variety of applica-
tions where excellent sound reinforcement, wide bandwidth directivity
control, and high efficiency is required in a compact package.
Max. Calculated SPL1: 138 dB
Passive Power Handling2: 500 W continuous, 2000 W peak
Impedance: 8 ohms (nominal), 6.0 ohms (min.)
LF Transducer - SMX2151, 15” (381 mm) driver
LF Axial Sensitivity4: 106 dB (1 W/1 m)
The EVH-1152D/66 utilizes the DH7N, a high-output 3” titanium com-
pression driver, coupled to a Constant Directivity™ 60° x 60° waveguide.
The SMX2151 15” woofer was developed using FEA optimization for
motor, suspension, and electrical design to ensure very low distortion,
high efficiency, and maximum intelligibility at high SPL. The crossover
uses steep, 24-dB-per-octave slopes with equalization for very smooth
response in the vocal range, linear off-axis response, and a protection
circuit for long-term reliability. This combination of technologies results
in a smooth response to 20 kHz and excellent pattern control down to
500 Hz.
LF Max. Calculated SPL: 138 dB
LF Power Handling3: 400 W continuous, 1600 W peak
LF Impedance: 8 ohms (nominal), 6.1 ohms (min.)
HF Transducer - DH7N, 3” (76 mm) diaphragm compression driver
HF Axial Sensitivity4: 112 dB (1 W/1 m)
HF Max. Calculated SPL: 137 dB
HF Power Handling3: 75 W continuous, 300 W peak
HF Impedance: 8 ohms (nominal), 6.0 ohms (min.)
The EVH-1152D/66’s features make it ideal for many fixed-install appli-
cations. The trapezoidal enclosure is constructed of weather-resistant
birch, and coated with EVCoatTM for protection from the elements. For
maximum protection against extreme outdoor elements, a fully-weath-
erized fiberglass version is available. The unique acoustic and rigging
design allows for vertical and horizontal clusters to be built using any
combination of loudspeakers from the entire EVF and EVH series. With
seven horn patterns to choose from, along with an assortment of low-
frequency and subwoofer loudspeakers, you have the tools to maxi-
mize flexibility of system design, no matter what the application and
budget. The innovative input panel provides a choice of Phoenix-style
connector (included in all standard models) or the ability to add a dual
NL4-type connector cover plate or gland-nut cover plate (for weather-
izing applications). An externally accessible jumper selects passive or
active operation. An available 70.7/100-V transformer kit may be easily
mounted to the input panel for use in distributed systems. All these
features give you the flexibility to address a large range of venues,
quickly and precisely supporting customer requirements with fewer
items in inventory.
Connectors: Dual four-pin 10 AWG
Phoenix/Euro Block
PI/FG Versions - CDG dual-gland-
nut input panel cover included
screw-terminals
Enclosure: 13-ply weather-resistant FG Version - 13-ply weather-resis-
birch with EVCoatTM
tant birch with fiberglass finish
Grille: 16 GA powder-coated
galvanneal with
PI/FG Versions -
Stainless steel with
hydrophobic cloth
rotatable logo
Environmental: IEC 60529 IP55 for PI and FG versions
Suspension: (28) M10 threaded suspension points
Dimensions 30.26” x 30.26” x 26.77”
(H x W x D): (768.6 mm x 768.6 mm x 680.1 mm)
Weight: 145.5 lb (66.1 kg) net, 160.5 lb (72.9 kg) shipping
1 Half-space measurement.
3 AES 2-1984, tested for eight hours.
4 Arithmetic averages, 300 - 1,300 Hz (LF) and
1,300 - 5,000 Hz (HF).
2 EIA RS-426A, tested for eight hours.
Engineering Data Sheet
Polar Plots (1/3 Octave):
400 Hz
500 Hz
1.25 kHz
3.15 kHz
8 kHz
630 Hz
800 Hz
1 kHz
2.5 kHz
6.3 kHz
16 kHz
1.6 kHz
2 kHz
4 kHz
5 kHz
10 kHz
12.5 kHz
20 kHz
Horizontal = Black
Vertical = Grey
Dimension Drawings:
End View
Front View
Side View
Rear View
EVH-1152D/66 Part Numbers
• PRD000305-001 EVH-1152D/66-BLK, 60° x 60°, black finish
• PRD000305-002 EVH-1152D/66-WHT, 60° x 60°, white finish
• PRD000305-003 EVH-1152D/66-PIB, 60° x 60°, black finish,
weather resistant
• PRD000305-004 EVH-1152D/66-PIW, 60° x 60°, white finish,
weather resistant
• PRD000305-005 EVH-1152D/66-FGB, 60° x 60°, black finish,
weather resistant fiberglass
• PRD000305-006 EVH-1152D/66-FGW, 60° x 60°, white finish,
weather resistant fiberglass
CAUTION
This EVH loudspeaker should be suspended overhead only
in accordance with the procedures and limitations
specified in the EVF/EVH User Manual and possible
manual update notices. This system should be suspended
with certified rigging hardware by an authorized rigging
professional and in compliance with local, state, and
federal overhead suspension ordinances.
Performance Match
Accessories
• PRD000303
• PRD000304
• PRD000306
• PRD000307
• PRD000308
• PRD000300
• PRD000302
• CPS2.9 120V
• CPS2.12 120V
• D170469
EVH-1152D/43, 40° x 30° coverage
EVH-1152D/64, 60° x 40° coverage
EVH-1152D/94, 90° x 40° coverage
EVH-1152D/96, 90° x 60° coverage
EVH-1152D/99, 90° x 90° coverage
EVF-2121S, dual 12” bass element
EVF-2151D, dual 15” bass element
CPS2.9, 120V power amplifier, 2 x 900W
CPS2.12, 120V power amplifier, 2 x 1200W
CPS4.5, 120V power amplifier, 4 x 500W
CPS4.10, 120V power amplifier, 4 x 1000W
• ACC000084-000 CDNL4, cover plate, dual NL4
• ACC000085-000 CSG, cover plate, single gland nut
• ACC000086-000 CDG, cover plate, dual gland nut
• ACC000087-000 TK-150, 70V transformer, 150W
• ACC000089-001 HRK-1B, horiz. rigging kit, EVF, black
• ACC000089-002 HRK-1W, horiz. rigging kit, EVF, white
• ACC000090-001 HRK-2B, horiz. rigging kit, EVF-SUB, black
• ACC000090-002 HRK-2W, horiz. rigging kit, EVF-SUB, white
• ACC000091-001 HRK-3B, horiz. rigging kit, EVH, black
• ACC000091-002 HRK-3W, horiz. rigging kit, EVH, white
• ACC000092-001 VRK-1B, vert. rigging kit, EVF, black
• ACC000092-002 VRK-1W, vert. rigging kit, EVF, white
• ACC000093-001 VRK-2B, vert. rigging kit, EVF-SUB, black
• ACC000093-002 VRK-2W, vert. rigging kit, EVF-SUB, white
• ACC000094-001 VRK-3B, vert. rigging kit, EVH, black
• ACC000094-002 VRK-3W, vert. rigging kit, EVH, white
• D170466
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Electro-Voice
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
Other Internatonal locations. For customer orders, Contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 887-9212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
© Bosch Communications Systems
07/2010
For technical assistance, contact Technical Support at: 866/78AUDIO
Part Number LIT000467066 Rev A
Specifications subject to change without notice.
|