Sound That Will Move You.
AWS
All Weather Speakers
Owner’s Manual
& Warranty
Models:
AWS-502
AWS-602
AWS-802
Sound That Will Move You.
Earthquake Sound reserves the right to amend details of the specifications without notice.
Copyright © Earthquake Sound Corporation
Earthquake Sound Corporation • 2727 McCone Avenue Hayward CA, 94545
Phone: 510-732-1000 Fax: 510-732-1095
Description
Description
Specifications
Specifications
AWS-502
AWS-602
AWS-802
Thank you for purchasing the new AWS indoor / outdoor speakers by
Earthquake Sound. Combining the infamous Earthquake Sound that will move
you with the latest and best weather resistance and manufacturing methods,
theAWS speakers are ideally suited for you with, the highlight feature being the
outdoor resistance - sun, rain, snow, heat and cold - or marine use. Their
presence is as equal indoors as well as out bringing life to your background
music, hi-fi, or home theater. All models in the AWS line are true two-way
designs with all acoustic parts sealed and gasketed against penetrating
weather.
Frequency Response
(±3dB)
68-20kHz
65-20kHz
55-20kHz
Recommended
Amplifier Power
20-125 Watts
8ohm
35-150 Watts
8ohm
60-200 Watts
8ohm
Nominal Impedance
Sensitivity (1W@1M)
Earthquake Sound Corp. has a proven history of successful and brilliant audio
products spanning over 19 years. Earthquake specifically designed the AWS
line to minimize damage caused by extreme weather conditions that typically
other speakers are not capable of defending against. With a durable
construction and proven materials like; molded PVC cabinets, electro plating,
UV protection, aluminum grills and brackets, gold-plated speaker connections.
Drivers constructed with high roll rubber surrounds, longer excursion for better
bass. Agile brackets make installation easier in most situations and the
speakers shape allows for simplified corner placement. TheAWS line is the best
choice in a large market of uncertain products tochoose from.
90dB
96dB
96dB
5 inch
(127mm)
6 inch
(152.40mm)
8 inch
(203.2)
Woofer
(Mica cone with butyl surround)
25mm ASV voice coil 25mm ASV voice coil 25mm ASV voice coil
One 3/4” (20mm)
PEI Mylar Dome
One 3/4” (20mm)
PEI Silk Dome
One 1” (25mm)
PEI Silk Dome
Tweeter
9 5/8” (244.475mm) 11 1/2” (292.10mm)
7 1/8” (180.975mm) 8 1/2” (215.90mm)
14 7/16”
Dimensions without bracket
(HxWxD)
(366.7125mm)
10 3/4” (273.05mm)
5 3/4” (146.05mm) 7 1/8” (180.975mm) 8 1/8” (206.375mm)
Powder
Coated
Aluminum
Powder
Coated
Aluminum
Powder
Coated
Aluminum
Grill and Bracket
Enclosure
High Temp
Molded PVC
High Temp
Molded PVC
High Temp
Molded PVC
4
5
Installation
Installation
How to Wire the AWS Speakers
Connecting to an Amplifier or Receiver
In order to achieve the best quality and stereo imaging from your AWS
speakers, you must wire the speakers correctly. Wiring can be quickly and
easily achieved, but be aware and cautious of your work, wiring incorrectly can
result in poor sound stage and bass reproduction. 18-gauge (or heavier)
speaker cables are recommended for lengths ranging from 25 feet and up. Prep
your cable for installation: strip the ends 1/2” (12mm) to expose wire, and tightly
twist the ends. For installations that are run on or through a building, use the
correct weather proofed wire that complies with local codes.
1) Connect the speaker terminals tothe amplifier speaker outputs.
2) When making all connections, be sure to connect +(positive) to +(positive)
and - (negative) to-(negative).
WARNING L
Prevent electrical shock, by switching off the amplifier or receiver when making
connections to the speaker. When making all connections, be sure to connect
the + (positive) on the speaker to the + (positive) on the amplifier, and the -
(negative) on the speaker tothe -(negative) on the amplifier.
-(negative)
+(positive)
-
+
+ -
Amplifier / Receiver
Verify That You Correctly Connected Your Speakers
Using the gold-plated binding
posts: you can easily connect
It is important that your speakers are hooked up with alike polarity or “in-phase”.
Use this easy test to determine if you have connected your speakers correctly.
Place speakers face-to-face, as close together as possible. Set your amplifier to
mono and begin listening to music, reverse the connections on one of the
speakers. You should hear distinguishable change in sound. The speaker that
plays louder and deeper is the one that is connected correctly.
IMPORTANT: Speaker wire is
usually marked or textured
banana-plugs, spade-plugs and
differently to distinguish between
bare wire. Insert the wire into the
positive and negative.
hole tighten securely (do not let
bare wire hang out side of hole).
6
7
Installation
Installation
Volume and Power Handling limitations
Mounting the AWS speakers
The listed power recommendations assume you will operate your system in a
way that will not produce distortion (blow your speakers). Even these speakers
can be damaged by a modest amplifier if it is not operated properly. If you hear
distortion (harsh or crackling noise) your’re over powering the speakers and
should immediately turn the volume down. Prolonged abuse caused by over
powering the speakers will cause permanent damage that may not be covered
by the Earthquake limited warranty.
Before you fasten all items down, you may want to test the placement of your
speakers to ensure that you are getting the best sound possible. Use the
supplied bracket to mount the speaker vertically or horizontally on your chosen
surface. The bracket offers multiple mounting options; key hole sockets and
standard screw holes the difference is usually based on the surface type(you
may want toconsult with an installer regarding the proper hard ware touse).
To mount, remove the bracket from the enclosure. To make wire less noticeable
you can insert it from the surface through the hole in the bracket and into the
connections. Mount the bracket in a desired location, and fasten the speaker to
the bracket. Finally face the speaker in the direction where the sound will most
needed.
Speaker Placement
Speaker location is one of the key factors for better sound quality. Taking your
time to place your speakers correctly ensures that your speakers will sound best
in any indoor or outdoor situation. Stereo sound is best heard when the
speakers are separated by at least 3-6ft. Usually placing speakers by a wall or
other surface will increase your bass response. Outdoors, placement under the
eaves of a roof reduces exposure to constant direct sunlight and precipitation,
which will extend the speaker life. Respect your neighbors; if you know that it will
affect your neighbors privacy face the speaker toward the intended listening
area tocontain the amount of distance that the sound will travel.
Earthquake also placed two 1/4”
threaded inserts on the back of the
speaker for alternative mounting
options. Some additional options
include floor stands, hanging devices
etc... These items can usually be
found at the dealer where you made
your purchase or any other audio
outlet.
If You Feel That the Speaker is Not Working
First contact the dealer where the speakers were originally purchased, if this is
not an option, you may contact the Earthquake service department;
510.732.1000. Products purchased on auction website or from unauthorized
Earthquake dealers will be charged shipping, labor and parts. Make sure you
protect your investment and buy from an authorized dealer.
8
9
|