C
Specifications
PW 3500 Series
Walkie Pallet
Truck
PW 3500
Series
Specifications
PW 3500 Series
1
2
3
4
5
8
9
Manufacturer
Model
Load Capacity
Power
Operator Type
Lift Height
Lift
Crown Equipment Corporation
PW 3510
6000
12 Volts
Walkie
9.25
PW 3520
6000 / 8000
24 Volts
Walkie
9.25
lb
Electric
Stand-up
in
in
6
6
10 Head Length
16 Outside Fork Spread
17 Speed Travel
Option 1 / Option 2
Standard Tip
Empty
4000 lb
6000 lb
in
in
mph
mph
mph
mph
30.44
22 / 27
3.3
2.8
2.4
29.19 / 35.69
22 / 27
3.4
3.0
2.8
2.6
8000 lb
na
PW 3500 Series
Standard-Tip Forks
Nominal Fork Length
11 Actual Fork Length
12 Overall Length
in
in
in
in
in
in
in
in
%
%
%
in
in
in
lb
lb
36
42
48
54
60
35.75
66.19
64.94
71.44
44.38
43.12
49.62
42
41.75
72.19
70.94
77.44
50.38
49.12
55.62
37
47.75
78.19
76.94
83.44
56.38
55.12
61.62
33
53.75
84.19
82.94
89.44
62.38
61.12
67.62
29
59.75
90.19
88.94
95.44
68.38
67.12
73.62
27
PW 3510
Option 1
Option 2
PW 3520
PW 3520
PW 3510
PW 3520
PW 3520
PW 3510
PW 3520
PW 3520
PW 3510
PW 3520
PW 3520
13 Wheelbase
Option 1
Option 2
14 Grade Clearance
15 Turning Radius
Option 1
Option 2
44
38
38
33
34
30
30
27
27
25
54.60
53.35
59.83
1310
1329
60.57
59.32
65.81
1326
1353
66.56
65.31
71.79
1342
1377
72.54
71.30
77.78
1358
1401
78.53
77.28
83.77
1381
1432
Option 1
Option 2
6000 lb
8000 lb
7
Truck Weight
Model
PW 3510-60
PW 3520-60
PW 3520-80
Drive Tire
Load Wheels
in
≤ 60"
> 60"
13.5 x 5.5 x 8 (r)
4 - 3.25 x 3.25 (-10)
2 - 3.25 x 6.50 (-35)
13.5 x 5.5 x 8 (r)
13 x 4.5 x 8 (p)
2 - 3.25 x 6.5 (-35)
2 - 3.25 x 6.5 (-35)
4 - 3.25 x 3.25 (-10)
2 - 3.25 x 6.5 (-35)
-10 Low rolling resistance, cut/tear resistance. Docks, rough floors, floor debris and traction.
-30 Moderate cut/tear resistance, high capacity. High capacity transport. Not for dock use.
-35 Highest cut/tear resistance offered. Extremely high capacity, low rolling resistance. Docks, rough floors and floor debris.
-40 Combines good cut/tear resistance and very high capacity. Use where nothing else works.
(r) = rubber, (p) = poly, ≤ = less than or equal to, > = greater than
Technical Information
PW 3500 Series
Maximum Battery Size
PW 3510-60: 7.94" wide x
31.12" long x 23.38" high
Standard Equipment
1. 12-volt fused electrical
system (PW 3510)
24-volt fused electrical
system (PW 3520-60/80)
Optional Equipment
11. Battery compartment rollers
12. Lift-off load backrest
1. Transistor on PW 3520-60/80
2. EE rating on PW 3520-60/80
13. Hinged load backrest with
quick release (48", 60" or
72" high)
PW 3520-60/80:
Option 1 - 6.69" wide x 34.44"
long x 23.38" high
Option 2 - 13.19" wide x 31.12"
long x 23.38" high
3. Curtis Unigage (discharge
indicator with lift lockout
and hour meter)
2. Resistor control
14. Storage module
3. Polyurethane load wheels
4. Discharge indicator
5. Hour meter
(Option 2 battery only)
4. Lift-off left and right battery
retainers
15. 7" wide fork
Batteries
(PW 3520-60 only)
PW 3510-60: 12-volt, up to
660 amp hour, 7.6 Kwh
Min/Max weight 400/540 lb
6. Quick adjustment caster
5. Full width, raise, lower, horn,
and end mounted reversing
button in control handle
16. Drive tire and load
wheel options
7. Quick adjustment caster
with torsion bar package
PW 3520-60/80:
Option 1 - 24-volt, 330 amp
hour, 7.7 Kwh
17. Toggle switch in lieu of key
18. Tandem load wheels
8. Battery retainer interlock
switch
6. Third speed cutout
7. 175 amp battery connector
(PW 3520-60/80)
350 amp battery connector
(PW 3510-60)
Min/Max weight 360/710 lb
Option 2 - 24-volt, 600 amp
hour, 13.9 Kwh
9. Quick battery disconnect
handle (PW 3520, right
side only)
19. Cold and corrosion
conditioning
20. Special color paint
21. Skid adapter
Min/Max weight 815/1400 lb
10. Left side battery connector
(right side standard)
8. Key switch
9. Horn
Technical Information
PW 3500 Series
Power disconnect
All wiring color coded
Key switch
To facilitate pallet entry/exit
Crown has engineered several
features into their fork assembly.
Standard-tip forks have pallet
entry rollers to lift fork over
bottom board of pallet. Rollers
are made of high molecular
weight polyethylene with .75"
axle and roll pin.
Pallet Planning Guide
Operator Controls
On PW models, the load wheel
will drop in the second opening
of the pallet. When “A” dimen-
sion equals nominal fork length,
“C” dimension is 6" maximum
and “B” is 14" minimum. On
models with tandem load
The PW 3500 Series has a
refined control handle, which
improves operator comfort and
productivity.
175 amp SB connector
(PW 3520-60/80) 350 amp
connector (PW 3510-60)
The Crown PW 3500 Series has
dual, soft urethane twist grips
with automatic return to neutral
when released. Two textures and
a unique “cam” design aid in
plugging, steering and long dis-
tance travel. On the control pod
are full width raise, lower and
horn buttons for easy actuation.
Third speed selector in control
handle may be used to shut off
high speed when operating in
congested areas. Reversing
Horn
wheels, the “C” dimension
should be 6" maximum and the
“B” dimension should be 17"
minimum. Customers that need
tandem load wheel trucks, but
use pallets with smaller open-
ings, may be accommodated if
the maximum lift height of the
truck is reduced. Contact your
local Crown dealer for details.
Hydraulic System
Abrasion-resistant steel entry/exit
slides on both sides of each fork
have convex bottom surfaces to
prevent snagging as forks move
over bottom boards of pallet.
One piece design with radiused
edges are welded away from
contact point of slide.
Heavy-duty pump, motor,
reservoir and control are assem-
bled into one unit. A centrally
located lift cylinder, mounted
vertically, is equipped with long-
life polyurethane packing.
Pressure-compensating flow
control valve is intergal part
of valve block and regulates
maximum lowering speed.
New exit roller design prevents
load wheel from dropping after
crossing bottom board. The 4"
wide, steel exit roller is posi-
tioned directly behind the load
wheel to keep the fork rolling.
New entry/exit slide design also
assists in trouble free pallet
entry/exit.
button in control handle reverses
direction of travel, if button should
come in contact with operator.
A
Overload valve protects
hydraulic components.
Electrical System
24-volt electrical system
(PW 3520-60/80)
12-volt electrical system
(PE 3510-60)
A
Drive Unit
All gear drive from drive motor to
drive wheel axle. Drive tire axle
is mounted in the drive unit on
both sides for maximum strength
in rough floor or docking appli-
cations. Drive unit is top and
bottom mounted. Top mount is
a large, tapered roller bearing for
vertical or horizontal forces.
Bottom mount has four shock
mounted rollers on drive unit
running in a hardened steel roller
race. Gear train runs in oil-filled,
sealed housing.
C
C
Series-wound, high-torque, fan-
cooled, Crown manufactured
drive motor for reliability and
ease of service.
B
B
Fork adjustment is done at the
toe with no need to remove a
cover plate. Fork heel height
adjustment is done quickly with-
out removing battery. Quick and
easy fork adjustment promotes
servicing of fork assembly to
keep pallet entry/exit productive.
First
Opening
Second
Opening
Series-wound, high-torque,
lift motor
Other Options
1. Audible travel alarm
Traction control systems:
2. Flashing lights
Resistor control has four heavy-
duty contactors with silver tips.
Solid-state time relay on resistor
control between 2nd and 3rd
speeds provide controlled
acceleration. Resistor is
Safety considerations and
dangers associated with
audible travel alarms and
flashing lights include:
Pull rod design incorporates a
replaceable “tenon” design for
fast servicing of pull rod while
still in the truck.
Caster System
Crown has designed two
optional caster systems for the
PW 3500 Series to meet high-
volume warehouse requirements.
• Multiple alarms and/or lights
can cause confusion.
Power Unit Structure
Rugged steel doors are sus-
pended on heavy-duty pin
standard on the PW 3500
Series. Transistor control is
optional on 24-volt models.
• Workers ignore the alarms
and/or lights after day-in and
day-out exposure.
hinges. Doors swing wide for
good access. Doors also can be
lifted off for unrestricted service
access. Door bolts have exclu-
sive convex design that mates
with concave door holes for fast
reinstallation of bolts. Heavy-steel
skirt surrounds entire area.
Option 1: Quick adjustment
casters enable braking, traction,
steer effort and stability to be
“balanced” based on your
specific applications.
Transistor control has many
benefits; maximum energy effi-
ciency, reduced maintenance
and infinite speed control.
Crown transistor controls feature
a 250 amp rated system; a
bypass contactor for maximum
current in heavy loading, ramping
applications; arc-less contactor
operation; ramp start; and a
sealed enclosure that protects
the transistor control from water,
contaminants, etc.
• Operator may transfer the
responsibility for “looking out”
to the pedestrians.
• Annoys operators and
pedestrians.
Option 2: All of the advantages
of quick adjustment casters are
yours, in addition to a torsion
bar suspension that maximizes
stability on tall, unwieldy and less
stable loads.
Dimensions and performance
data given may vary due to
manufacturing tolerances.
Performance is based on an
average size vehicle and is
affected by weight, condition of
truck, how it is equipped and the
conditions of the operating area.
Crown products and specifica-
tions are subject to change
without notice.
Brake
Internal expanding mechanical
brake with 4.5" drum and
bonded brake linings. Brake
drum is mounted on drive
motor shaft and braking effort
is transmitted through the gear
reductions. Brake is actuated by
control handle position.
Fork Assembly
Fork width - 9.12" on standard-
tip fork models, fork spread - 22"
and 27" standard on standard-
tip models. 23" - 26" spread
available in one-inch increments.
Lift limit switch operates at
maximum lift height to shut off
pump motor.
Control and power circuits
are fused.
Crown Equipment Corporation
New Bremen, Ohio 45869 USA
Tel 419-629-2311
C
Fax 419-629-3796
crown.com
Because Crown is continually improving its products,
specifications are subject to change without notice.
Crown and the Momentum symbol are trademarks of
Crown Equipment Corporation.
Copyright 1993-2005 Crown Equipment Corporation
SF12156 Rev. 4/05
Printed in U.S.A.
|