Crown Audio Stereo Amplifier XLS 802 User Manual

X L S S E R I E S  
XLS 802  
Architectural & Engineering Specifications  
Crown® XLS 802  
The power amplifier shall meet or exceed the following performance  
criteria: Sensitivity for full rated power at 4 ohms: 1.25 V. Rated output  
with both channels driven with 0.5% THD (at 1 kHz) in Dual mode: 800  
The power amplifier shall be a solid-state two-channel model.  
watts per channel into 4 ohms and 500 watts per channel into 8 ohms.  
Rated output with 0.5% THD (at 1 kHz) in Bridge-Mono mode: 1,600  
watts into 8 ohms. Frequency Response at 1 watt, 22 Hz to 20 kHz: +0 dB,  
–1 dB. Signal to Noise Ratio below rated power (20 Hz to 20 kHz, inputs  
terminated): greater than 100 dB A-weighted. Total Harmonic Distortion  
at full rated power, 1 kHz: less than 0.5%. Intermodulation Distortion (60  
Hz and 7 kHz at 4:1, from full rated output to –40 dB: less than 0.3%.  
Damping Factor (8 ohms): greater than 200 from 10 to 400 Hz. Crosstalk  
(below rated power, –75 dB at 1 kHz, –50 dB at 20 kHz. Input Impedance  
(nominal): 20 kilohms balanced, 10 kilohms unbalanced. AC Line Voltages  
and Frequencies Available ( 10%): 120 VAC 60Hz, 100 VAC 50/60 Hz, 220  
VAC 50 Hz, 230-240 VAC 50 Hz.  
The amplifier shall provide extensive protection and diagnostic capabili-  
ties, including output current limiting, DC protection, circuit breaker, and  
thermal protection.  
The front-panel controls shall be two black detented level controls (one for  
each channel) and a power switch. The rear-panel controls shall be a circuit  
breaker reset switch and a Dual/Bridge-Mono mode switch.  
Front-mounted indicators shall be the following: Signal Presence Indica-  
tors: Two green LEDs, one for each channel, illuminate when the channel’s  
input signal exceeds –40 dBu. Clip Indicators: Two red LEDs, one for each  
channel, illuminate when the channel’s output is being overdriven. Power  
Indicator: Blue LED indicates amplifier has been turned on and AC  
power is available. Fault Indicator: Two red LEDs illuminate when amplifier  
is in protect mode. Also illuminates briefly during normal power-up when  
amplifier is first switched on.  
The amplifier chassis shall be constructed of steel with a durable black  
finish and shall be designed for flow-through ventilation from the front  
panel to the back panel. Internal heat sinks with forced-air cooling shall  
provide rapid, uniform heat dissipation.  
The recommended load impedance shall be 4 to 8 ohms per channel in  
Stereo, and 8 ohms in Bridge Mono.  
The rear-mounted output connectors shall be two 4-pole Speakon® con-  
nectors (one per channel) and a pair of binding posts per channel. Rear-  
mounted input connectors shall be 3-pin balanced XLR connectors.  
The dimensions of the amplifier shall allow for 19 inch (48.3 cm) EIA  
standard (RS-310-B) rack mounting. The amplifier shall be 3.5 inches (8.9  
cm) tall, and 15.2 inches (38.6 cm) deep.  
The amplifier shall weigh 35.5 pounds (16.1 kg).  
The amplifier shall be designated the Crown XLS 802.  
Crown International  
1718 W. Mishawaka Rd.  
Elkhart, IN 46517-9439  
TEL: 574-294-8200  
FAX: 574-294-8FAX  
Specifications subject to change without prior notice. Latest  
Crown and Crown Audio are registered trademarks of Crown  
International. Other trademarks are the property of their respec-  
tive owners.  
© 2006 Crown Audio® Inc. Printed in U.S.A.  
9/06  
 
139440-1C  

Conair Automobile Accessories HMC1 User Manual
Craftsman Lawn Mower 91738836 User Manual
Crosley Radio Stereo System CR10 User Manual
Desa Water Heater CCL3018NA User Manual
Dualit Hot Beverage Maker Dome Kettle User Manual
Eureka Water System Aquaguard User Manual
Euro Pro Iron EP7005 User Manual
Fisher Paykel Oven OB60SL9DEX User Manual
Fisher Paykel Ventilation Hood HC60PCIX2 User Manual
Fisher Price Automobile Accessories G5911 User Manual