Owner’s manual
Mode d’emploi
1. PRECAUTIONS
1. When the inside of the car is very cold and
the player is used soon after switching on
the heater, moisture may form on the disc
or the optical parts of the player and proper
playback may not be possible. If moisture
forms on the disc, wipe it off with a soft
cloth. If moisture forms on the optical parts
of the player, do not use the player for about
one hour and the condensation will disap-
pear naturally to allow normal operation.
This equipment has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reason-
able protection against harmful interference in
a residential installation. This equipment gen-
erates, uses, and can radiate radio frequency
energy and, if not installed and used in accor-
dance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interfer-
ence will not occur in a particular installation. If
this equipment does cause harmful interfer-
ence to radio or television reception, which can
be determined by turning the equipment off
and on, the user is encouraged to consult the
dealer or an experienced radio/TV technician
for help.
Manual de instrucciones
■Contents
English
2. Driving on extremely bumpy roads which
cause severe vibration may cause the
sound to skip.
1. PRECAUTIONS...........................................................2
2. CONTROLS.................................................................3
3. BUTTON TERMINOLOGY..........................................4
4. FEATURES..................................................................5
5. HANDLING COMPACT DISCS...................................6
6. DCP (Detachable Control Panel)..............................7
7. REMOTE CONTROL...................................................8
8. OPERATION..............................................................10
9. TROUBLESHOOTING ..............................................16
10.ERROR DISPLAYS...................................................17
11.SPECIFICATIONS.....................................................18
3. This unit uses
a
precision mechanism.
Even in the event that trouble arises, never
open the case, disassemble the unit, or
lubricate the rotating parts.
■Table des matières
CAUTION
Français
DX425
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
THE COMPACT DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE
EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL.
1. PRÉCAUTIONS.........................................................19
2. COMMANDES.............................................................3
3. NOMENCLATURE DES TOUCHES .........................20
4. CARACTÉRISTIQUES..............................................21
5. MANIPULATION DES DISQUES COMPACTS ........22
6. CLAVIER DE COMMANDE AMOVIBLE (DCP) .......23
7. TÉLÉCOMMANDE....................................................24
8. FONCTIONNEMENT.................................................26
9. DÉPISTAGE DES PANNES......................................32
10.AFFICHAGE DES ERREURS...................................33
11.SPÉCIFICATIONS.....................................................34
AM/FM CD PLAYER
WITH CD CHANGER CONTROL
•
MODEL
RADIO AM/FM-LECTEUR CD
AVEC COMMANDE DE CHANGEUR CD
12V
GROUND
AM 530-1710kHz/FM 87.9-107.9MHz
•
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:
(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
■Índice
Español
RADIO AM/FM Y REPRODUCTOR CD
CON CONTROL DE CAMBIADOR DE CD
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR
1. PRECAUCIONES......................................................35
2. CONTROLES..............................................................3
3. NOMENCLATURA DE LOS BOTONES...................36
4. CARACTERÍSTICAS ................................................37
5. MANEJO DE LOS DISCOS COMPACTOS..............38
6. PANEL DE CONTROL DESMONTABLE (DCP) ......39
7. CONTROLADOR REMOTO.........................................40
8. OPERACIÓN.............................................................42
9. SOLUCIÓN DE PROBLEMAS..................................48
10.INDICACIONES DE ERROR ....................................49
11.ESPECIFICACIONES ...............................................50
SUBCHAPTER
J
APPLICABLE AT DATE OF MANUFACTURE.
CLARION CO.,LTD.
50 KAMITODA,TODA-SHI,SAITAMA-KEN,JAPAN
Bottom View of Source Unit
MANUFACTURED:
286-
Clarion Co.,Ltd.
MADE IN CHINA
SERIAL No.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT WILL VOID THE WARRANTY AND WILL
VIOLATE FCC APPROVAL.
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2001: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Impreso en China
Be sure to unfold and read the next page.
Veuillez déployer et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
PE-2498B
280-7750-00
2001/11 (D/C)
DX4 2 5
2
4. FEATURES
■ Rotary Encoder Volume Control
■ DIN Chassis with Detachable Control Panel
■ CD-R/CD-RW Compatible
■ Z-ENHANCER PLUS for Sound Creation with 3 Adjustment Modes (2-Band P.EQ)
■
® FM Reception System
■ AM/FM Bands-1 AM, 3 FM/18 FM/6 AM Touchbutton Memory
■ 8-Times Oversampling Digital Filter and Dual 1-Bit D/A Converters
■ Zero-Bit Detector™ Mute Circuit
■ Repeat/Random Play/Intro Music Scan
■ Blue Negative LC Display
■ 4-Channel RCA Line Level Output with Fader Control
DX4 2 5
5
5. HANDLING COMPACT DISCS
This unit has been designed specifically for play-
Note on Compact Discs
Never stick labels on the surface of the compact
disc or mark the surface with a pencil or pen.
back of compact discs bearing the
No other discs can be played.
mark.
To remove the compact disc from its storage
case, press down on the center of the case and
lift the disc out, holding it carefully by the edges.
No
Proper way to hold
the compact disc
Removing the disc
Do not use any solvents such as commercially
available cleaners, anti-static spray, or thinner to
clean compact discs.
Always handle the compact disc by the edges.
Never touch the surface.
No
To remove fingermarks and dust, use a soft
cloth, and wipe in a straight line from the center
of the compact disc to the circumference.
No
Do not use compact discs that have large
scratches, are misshapen, or cracked, etc. Use
of such discs will cause misoperation or damage.
No
New discs may have some roughness around
the edges. The unit may not work or the sound
may skip if such discs are used. Use a ball-point
pen, etc. to remove roughness from the edge of
the disc.
Ball-point pen
Roughness
Do not expose compact discs to direct sunlight
or any heat source.
No
Note:
Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These
•
may get caught in the internal mechanism and damage the disc.
6
DX4 2 5
6. DCP (Detachable Control Panel)
The control panel can be detached to prevent
theft. When detaching the control panel, store it
Storing the DCP in the DCP Case
Hold the DCP, in the orientation as shown in the
in the included DCP case to prevent scratches.
figure below, and put it into the supplied DCP
We recommend taking the detachable control
case. (Ensure the DCP is in the correct orienta-
panel with you when leaving the car.
tion.)
Removing the DCP
DCP
1. Turn off the power.
2. Press the DCP Release button 1.
DCP
release button 1
DCP case
CAUTION
• The DCP can easily be damaged by shocks. After
removing it, place it in a protective case and be
careful not to drop it or subject it to strong shocks.
When the release button is pressed and the DCP is
unlocked, the car’s vibrations may cause it to fall.
To prevent damage to the DCP, always store it in a
protective case after detaching it.
•
3. Remove the DCP.
The rear connector that connects the source unit
and the DCP is an extremely important part. Be
careful not to damage it by pressing on it with fin-
gernails, pens, screwdrivers, etc.
•
DCP Rear Panel
Source Unit Front
DCP
The DCP is unlocked.
*
DCP
connector
Source unit connector
Attaching the DCP
Insert the DCP into the right side of the source
unit and press the left side to lock it.
Note:
If the DCP is dirty, wipe off with a soft, dry cloth only.
•
CAUTION
Do not insert the DCP from the left side. Doing so
may damage it.
2.
1.
DX4 2 5
7
7. REMOTE CONTROL
Receiver for remote control unit
Operating range: 30° in all directions
Remote Control Unit
Signal transmitter
&
(
¡
)
*
£
™
¢
¶
∞
§
Inserting the Batteries
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
AA (UM-3/1.5 V)
Batteries
2. Insert the AA (UM-3/1.5 V) batteries that
came with the remote control unit facing in
the directions shown in the figure, then close
the rear cover.
Notes:
Using batteries improperly can cause them to explode.
Take note of the following points:
Rear cover
• When replacing batteries, replace both batteries with
new ones.
Rear side
• Do not short-circuit, disassemble or heat batteries.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
8
DX4 2 5
Functions of Remote Control Unit Buttons
Mode
Radio
CD
Button
& FUNC
Turns power on and off. When pressed and held for 1 second: Turns power off.
Switches between radio and CD.
* BAND
Switches reception band.
Plays the first track.
Top play.
DISC UP
PROG
TOP
( VOLUME
) SEARCH
Increases and decreases volume (in all modes).
Moves preset channels up and down. Moves tracks up and down.
When pressed and held for 1 second:
Fast-forward/
fast-backward.
¡ PLAY/PAUSE Turns mute on and off.
Switches between playback and pause.
Switches between playback and pause.
™ MUTE
£ ISR
Turns mute on and off.
Recalls ISR radio station in memory.
Press and hold for more than 2 seconds: Stores current station into ISR memory
(radio mode only).
¢ DISP
Switches among main display, sub display and clock display.
∞ SCN
Preset scan.
When pressed and held for 2 seconds:
Auto store.
Scan play.
PS/AS
§ RPT
No function.
No function.
Repeat play.
BLS
¶ RDM
Random play.
MONI
* Some of the corresponding buttons on the source unit and remote control unit have different functions.
DX4 2 5
9
8. OPERATION
Note:
Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
•
Adjusting the Tone
Basic Operations
Press A button % and select the item to adjust.
Each time you press A button %, the item
changes in the following order:
● When “B-BOOST” is set
“B-BOOST” ➜ “BAL” ➜ “FAD” ➜ Previous
mode
CAUTION
When this unit is turned on, starting and stop-
ping the engine of a car with its volume raised
to the maximum level may harm your hearing.
Be careful about adjusting the volume.
When “B-BOOST” is set, the bass adjustment
value can be adjusted in the range of –3 to +3 by
rotating the Rotary knob $ clockwise or coun-
terclockwise.
Turning ON the Power and Adjusting
the Volume
1) Press the POWER button 3.
● When “IMPACT” is set
“IMPACT” ➜ “BAL” ➜ “FAD” ➜ Previous
mode
When “IMPACT” is set, the treble adjustment
value can be adjusted in the range of –3 to +3 by
rotating the Rotary knob $ clockwise or coun-
terclockwise.
● When “EXCITE” is set
“EXCITE” ➜ “BAL” ➜ “FAD” ➜ Previous
mode
When “EXCITE” is set, the bass and treble
adjustment value can be adjusted in the range of
–3 to +3 by rotating the Rotary knob $ clock-
wise or counterclockwise.
To turn off the power, press the POWER button
3 for 1 second or longer.
*
2) Press the FUNC button 3 and select anoth-
er operation mode. Every time the FUNC but-
ton 3 is pressed, the display changes the
operation mode as:
Radio ➜ CD ➜ (CD Changer) ➜ Radio
Notes:
The operation mode not connected to the unit will not
be selected.
•
If the CD mode is selected when no disc is inserted,
the display shows “ NO DISC”.
•
3) Turning the Rotary knob
$
clockwise
increases the volume; turning it counterclock-
wise decreases the volume.
The volume level is from 0 (minimum) to 33 (max-
● When “CUSTOM” is set
“BASS” ➜ “TREB” ➜ “BAL” ➜ “FAD” ➜
Previous mode
*
imum).
● When “Z+ OFF” is set
“BAL” ➜ “FAD” ➜ Previous mode
When the Z button 9 is pressed and hold for 1
second or longer with the tone effect set to “B-
BST”, “IMPACT” or “EXCITE”, the sound char-
acteristics become flat and the indication “FLAT”
is shown in the display.
Setting the Z-enhancer Plus
This unit comes with 4 types of sound tone
effects stored in memory. Select the one you
prefer.
The factory default setting is “CUSTOM”.
*
Each time you press Z button 9, the tone effect
changes in the following order:
Adjusting the Bass
This adjustment can be performed when the Z-
enhancer Plus is set to “CUSTOM”.
“B-BOOST” ➜ “IMPACT” ➜ “EXCITE” ➜
“CUSTOM” ➜ “Z+ OFF” ➜ “B-BOOST” ...
• B-BOOST : bass emphasized
1) Press A button % and select “BASS”.
• IMPACT
• EXCITE
: treble emphasized
: bass and treble emphasized
2) Turning Rotary knob $ clockwise empha-
sizes the bass; turning it counterclockwise
attenuates the bass.
• CUSTOM : bass and treble adjustment
• Z+ OFF : no sound effect
The factory default setting is “0”. (Adjustment
range: –6 to +6)
*
3) When the adjustment is complete, press A
button % several times until the function
mode is reached.
10
DX4 2 5
Adjusting the Treble
Switching the Clock Display
This adjustment can be performed when the Z-
enhancer Plus is set to “CUSTOM”.
Every time the DISP button 7 is pressed, the
display will change between the operation mode
and the clock display.
1) Press A button % and select “TREB”.
2) Turning Rotary knob $ clockwise empha-
sizes the treble; turning it counterclockwise
attenuates the treble.
Setting the Clock
1) Press the DISP button 7 to display the clock
The factory default setting is “0”. (Adjustment
range: –6 to +6)
*
display.
2) Press and hold the DISP button 7 for 1 sec-
3) When the adjustment is complete, press A
button % several times until the function
mode is reached.
ond or longer.
3) Press the SRCH Left button 2, then set the
current hour.
4) Press the SRCH Right button 2, then set the
Adjusting the Balance
current minute.
1) Press A button % and select “BAL”.
5) Press the DISP button 7, then the clock is
2) Turning the Rotary knob $ clockwise empha-
sizes the sound from the right speaker; turn-
ing it counterclockwise emphasizes the sound
from the left speaker.
set.
Notes:
If you select another operation mode while you are
setting the clock, the clock setting operation will be
canceled.
•
The factory default setting is “0”. (Adjustment
range: L13 to R13)
*
If you remove the vehicle’s battery for a check or
repair, the clock will be reset, so you must set it again.
•
3) When the adjustment is complete, press A
button % several times until the function
mode is reached.
Turning the screen saver function
on or off
This unit is equipped with the function which
enables you to display a variety of patterns and
characters in the Operation status indication 2
in a random order. You can turn this function on
or off.
Adjusting the Fader
1) Press A button % and select “FAD”.
2) Turning the Rotary knob $ clockwise empha-
sizes the sound from the front speakers; turn-
ing it counterclockwise emphasizes the sound
from the rear speakers.
The factory default setting is on.
*
The factory default setting is “0”. (Adjustment
range: F12 to R12)
While pressing the Disp button 7, press the SS
button ! to switch the function.
*
3) When the adjustment is complete, press A
button % several times until the function
mode is reached.
The following illustration shows one of the patterns
displayed when the screen saver function is set to on.
*
Loudness Effect
In order to turn on/off the loudness effect, use
the LD button % for 1 second or longer. Every
time the LD button % is pressed and held for 1
second or longer, the loudness effect switches
on and off.
When the loudness effect is on, the display will show
“LD”.
*
DX4 2 5
11
Preset Memory Function
Radio Mode Operations
Preset Memory Function can store up to 24 sta-
tions: six stations for each of FM1, FM2, FM3
and AM.
FM Reception
For enhanced FM performance the
®
tuner includes signal actuated stereo control and
Multipath noise reduction circuits.
Note:
When the present memory function is used, all the
•
content of the memory will be erased.
Listening to the Radio
Manual memory function
1) Press the FUNC button 3 to select the radio
1) Press the BAND button 4, and select the
mode, then the radio will be on.
band you want to store in the memory.
2) To select a preset band, press the BAND but-
ton 4, then select one of the preset bands
such as FM1, FM2, FM3, or AM. Every time
the BAND button 4 is pressed, the display
will change as:
2) Press the SRCH Left/Right button 2 then
select the station you want to store in the
memory.
3) Press and hold the Preset button @ for 2
seconds or longer, then the station will be
stored in the memory.
F1 (FM1) ➜ F2 (FM2) ➜ F3 (FM3) ➜ AM ➜
F1 (FM1)
3) Press the SRCH Left/Right button 2, then
the station at which there is a broadcast will
be selected (Seek selection).
Auto store function (Automatic Station Store)
1) Press the BAND button 4, then select the
band you want to store in the memory.
2) Press and hold the AS button 5 for 2 sec-
onds or longer, then the station at which the
reception is the strongest will be automatical-
ly stored in the memory.
Mute
Use this function to turn off the sound immedi-
ately.
Press the MUTE button ¥. The sound turns off
and “MUTE” appears on the display. Press the
MUTE button again to cancel the mute mode.
Note:
When the number of stations stored is less than six,
the previous content of the memory for each direct
button will be retained.
•
Manual Tuning
1) Press the BAND button 4, then select FM1,
Preset Scanning (Preset Station Scan)
FM2, FM3 or AM.
When the PS button 5 is pressed, the preset
memory numbers flash and the stations are
tuned in for 7 seconds each in the order in which
they were stored. Press the PS button 5 again
to cancel the preset scanning mode.
2) Press and hold the BAND button 4 for 1 sec-
ond or longer, then the display will show
“MANU”, which means that a manual selec-
tion function is on.
3) Press the SRCH Left/Right button 2 and
select the right station.
Instant Station Recall (ISR)
With this function, a specific radio station can be
recalled from any mode.
Seek Tuning
1) Press the BAND button 4, then select FM1,
ISR memory
FM2, FM3 or AM.
1) Press the FUNC button 3, then select the
2) If the “MANU” on the display is on, press and
hold the BAND button 4 for 1 second or
longer. When the “MANU” display is off, the
Seek Selection function is on.
radio mode.
2) Select the radio station which you want to
store in the memory.
3) Press and hold the ISR button # for 2 sec-
3) Press the SRCH Left/Right button 2, then
when it selects the station in which there is a
broadcast, it automatically stops.
onds or longer.
12
DX4 2 5
Recalling ISR
CD Mode Operations
Press the ISR button # then the display will
show “ISR”, then the radio station previously
memorized will be selected. Press the ISR but-
ton # again to disengage the unit from the
Recalling ISR function.
Loading a Disc
Insert the disc into the CD insertion slot with its
label side up, then the CD will start playing.
For 5-inch (12 cm) CD For 3-inch (8 cm) single CD
Area Change
Use this function when you are using the car
stereo anywhere outside the U.S.
Switchable frequency spacing
This car stereo is initially set to tune in frequen-
cy intervals of 10 kHz for AM and 200 kHz for
FM, the standard calibrations in the U.S. When
using the unit outside the U.S., use the following
procedure to switch the frequency range.
The table below lists the frequency specifica-
tions for the U.S. and other countries.
When inserting a single CD (3”(8 cm)), insert it from
the center of the slot.
*
When inserting a single CD (3”(8 cm)), do not con-
nect an adapter.
*
Initial Setting New Setting
(U.S. standard) (outside U.S.)
Press the DISP button 7, then the display will show
the play time.
*
Frequency
spacing
10 kHz
530 to
9 kHz
531 to
Notes:
AM
FM
Some CDs recorded in CD-R/CD-RW mode may not
be usable.
•
Frequency
range
1,710 kHz 1,629 kHz
Listening to the Disc already Inserted
Press the FUNC button 3 to select the CD
mode, the CD will start playing.
Frequency
spacing
200 kHz
87.9 to
50 kHz
87.5 to
Frequency
range
107.9 MHz 108 MHz
Stopping (pausing) Playback
Switching the area change
Outside U.S. (New Setting)
While pressing the BAND button 4, press the
SRCH Left button 2, then “outside U.S.” will be
selected.
Press the Play/Pause button ¥.
Press the Play/Pause button ¥ again to resume
playback.
Ejecting the CD
Press the Eject button 8, then the CD will be
ejected.
Inside U.S. standard (Initial Setting)
While pressing the BAND button 4, press the
SRCH Right button 2, then the “U.S. standard”
will be selected.
Note:
If the ejected CD is left as it is, it will be reloaded after
15 seconds. However, single CDs will not be
reloaded, so make sure to remove them.
•
DX4 2 5
13
Top Function
The top function allows the first track of the cur-
rent CD to be played.
Press Top button 4 to play the first track (track
No.1) of CD.
CD Changer Operations
When a separately sold CD changer is connect-
ed, it can be controlled from this unit.
Listening to the disc
Press the FUNC button 3 and select the CD
Selecting Tracks (songs)
changer mode, then the CD starts playing.
Press the SRCH Left/Right button 2.
: Playback will start from the next track.
: Playback will start from the beginning of
the track currently playing. When this
button is pressed again, the CD will play
from the previous track.
Stopping (pausing) playback
Press the Play/Pause button ¥.
Press the Play/Pause button ¥ again to resume
playback.
Fast-Forward and Fast-Backward
Press and hold the SRCH Left/Right button 2.
Selecting a CD
Each of the Direct buttons @ corresponds to a
disc loaded into the magazine.
• Selecting a disc from 1 to 6
Press the corresponding Direct button @ (1 to 6)
to select the desired disc.
: To fast-forward
: To fast-backward
Pressing the SRCH Left/Right button for 1 second or
*
longer will move forward or backward 5 times faster
than normal play, and pressing it for 3 seconds or
longer will do the operation 30 times faster.
• Selecting a magazine from 1 to 3 (only when
there is disc in the magazine)
Press BAND button 4 to select the desired
magazine.
Scan Play (Intro Music Scan)
Press the SCN button 5, then the display
shows “SCN”, then the CD will play the first 10
seconds of each track of the whole disc. Press
the SCN button 5 again to disengage the unit
from scan play.
If a CD is not loaded in a slot of the magazine, press-
ing the Direct button @ corresponding to its disc
number is invalid.
*
Selecting tracks (songs)
A scan play will start from the track following the one
currently playing.
*
Press the SRCH Left/Right button 2.
: Playback will start from the next track.
: Playback will start from the beginning of
the track currently playing. When this
button is pressed again, the CD will play
from the previous track.
Repeat Play
Press the RPT button 6, then the display shows
“RPT”, then the track currently playing will be
played repeatedly. Press the RPT button 6
again to disengage the unit from repeat play.
Fast-forward and fast-backward
Press and hold the SRCH Left/Right button 2.
: To fast-forward
Random Play
Press the RDM button 0, then the display will
show “RDM”, then the entire tracks on the disc
will be played at random. Press the RDM button
0 again to disengage the unit from random play.
: To fast-backward
Pressing the SRCH Left/Right button 2 for 1 second
or longer will move forward or backward 3 times faster
than normal play, and pressing it for 3 seconds or
longer will do the operation 30 times faster.
*
14
DX4 2 5
Scan play
Disc random playback
Press the SCN button 5, then the display
shows “SCN”, then the CD will play the first 10
seconds of each track of the whole disc. Press
the SCN button 5 again to disengage the unit
from scan play.
Press and hold the RDM button 0 for 1 second
or longer, then the display will show both the
DISC indication 0 and “RDM”, then the entire
tracks of all the discs in the CD changer will be
played at random.
A scan play will start from the track following the one
currently playing.
Press the RDM button 0 again to disengage the
unit from disc random play.
*
Disc scan play
Switching magazine
Press and hold the SCN button 5 for 1 second
or longer, then the display will show DISC indi-
cation 0 and “SCN”, and plays the first 10 sec-
onds of all the tracks of all the CDs in the CD
changer.
This function can be used only when the con-
nected CD changer can store a multiple number
of magazines.
Every time the MAG button 4 is pressed, the
next magazine will be selected.
Notes:
• Regarding MD Changer when a MD changer is used
with this unit, set the mode on the changer to “A” (CD
Mode).
Press the SCN button 5 again to disengage the
unit from disc scan play.
A scan play will start from the track following the one
currently playing.
*
The MD Changer can then be used in the CD chang-
er mode. When used in this way, however, title can not
be displayed.
Repeat play
Press the RPT button 6, then the display shows
“RPT”, then the track currently playing will be
played repeatedly. Press the RPT button 6
again to disengage the unit from repeat play.
• Also, a CD changer cannot be connected concurrent-
ly with a MD changer.
Disc repeat play
Press and hold the RPT button 6 for 1 second
or longer, then the display shows both the DISC
indication 0 and “RPT”, then the disc currently
being played will be played repeatedly.
Press the RPT button 6 again to disengage the
unit from disc repeat play.
Random play
Press the RDM button 0, then the display will
show “RDM”, then the entire tracks on the disc
will be played at random.
Press the RDM button 0 again to disengage the
unit from random play.
DX4 2 5
15
9. TROUBLESHOOTING
Problem
Cause
Solution
Power does not turn on.
(No sound is produced.)
Fuse is blown.
Replace with a fuse of the same
amperage. If the fuse blows again,
consult your store of purchase.
Incorrect wiring.
Consult your store of purchase.
Compact disc cannot be
loaded.
Another compact disc is
already loaded.
Eject the compact disc before loading
the new one.
Sound skips or is noisy.
Compact disc is dirty.
Clean the compact disc with a soft
cloth.
Compact disc is heavily
scratched or warped.
Replace with a compact disc with no
scratches.
Let dry for about 1 hour with the
power on.
Sound is bad directly after Water droplets may form
power is turned on.
on the internal lens when
the car is parked in a
humid place.
Nothing happens when
buttons are pressed.
Display is not accurate.
Microprocessor has
malfunctioned due to
noise, etc.
Turn off the power, then press the
DCP Release button 1 and remove
the DCP.
Press the reset button for about 2
seconds with a thin rod.
Reset button
DCP or source unit
connectors are dirty.
Wipe the dirt off with a soft cloth
moistened with cleaning alcohol.
16
DX4 2 5
10. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed.
Take the measures described below to eliminate the problem.
Error Display
CD ER2
Cause
Measure
A CD is caught inside the CD deck and is This is a failure of CD deck’s mechanism
not ejected.
and consult your store of purchase.
CD ER3
CD ER6
A CD cannot be played due to scratches,
etc.
Replace with a non-scratched,
non-warped-disc.
A CD is loaded upside-down inside the
CD deck and does not play.
Eject the disc then reload it properly.
CDCH ER2
A CD inside the CD changer is not
loaded.
This is a failure of CD changer’s
mechanism and consult your store of
purchase.
CDCH ER3
CDCH ER6
A CD inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-
warped disc.
A CD inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
If an error display other than the ones described above appears, press the reset button. If the problem
persists, turn off the power and consult your store of purchase.
DX4 2 5
17
11. SPECIFICATIONS
FM Tuner
General
Frequency Range: 87.9 MHz to 107.9 MHz
Usable Sensitivity: 11 dBf
Power Supply Voltage: 14.4 V DC (10.8 V to 15.6
V allowable), negative ground
50 dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation (1 kHz): 35 dB
Frequency Response (±3 dB): 30 Hz to 15 kHz
Current Consumption: Less than 15 A
Speaker Impedance: 4 Ω (4 Ω to 8 Ω allowable)
Weight: 3.97 lb. (1.8 kg)
Dimensions:
7” (178 mm) Width × 2” (50 mm) Height ×
6-1/8” (155 mm) Depth
AM Tuner
7”
2”
(50 mm)
Frequency Range: 530 kHz to 1,710 kHz
Usable Sensitivity: 25 µV
(178 mm)
CD Player
System: Compact disc audio system
Usable Discs: Compact disc
Frequency Response: 10 Hz to 20 kHz (±1 dB)
Signal-to-Noise Ratio: 100 dB (1 kHz) IHF-A
Dynamic Range: 95 dB (1 kHz)
7-3/8”
(188 mm)
2-1/4”
(58 mm)
Harmonic Distortion: 0.01%
Notes:
Specifications comply with JEITA Standards.
•
•
Specifications and design are subject to change with-
out notice for further improvement.
Audio
Maximum Power Output:
200 W (50 W × 4 ch)
Continuous Average Power Output:
18 W × 4, into 4 Ω, 20 Hz to 20 kHz,1%THD
Bass Control Action (30 Hz): ±12 dB
Treble Control Action (10 kHz): ±10 dB
Line Output (with CD changer 1 kHz, 10 kΩ):
1.8 V
18
DX4 2 5
|