ADMINISTRATION
GUIDE
Cisco Small Business
WAP121 Wireless-N Access Point with PoE
and
WAP321 Wireless-N Selectable-Band Access Point
with PoE
Contents
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
1
Contents
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
2
Contents
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
3
Contents
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
4
Contents
Propagation of Configuration Settings and Parameters in
Single Point Setup
160
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
5
Contents
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
6
1
Getting Started
This chapter provides an introduction to the Wireless Access Point (WAP) devices
web-based configuration utility, and includes these topics:
•
•
•
•
Starting the Web-Based Configuration Utility
This section describes system requirements and how to navigate the web-based
configuration utility.
Supported Browsers
•
•
•
•
Internet Explorer 7.0 or later
Chrome 5.0 or later
Firefox 3.0 or later
Safari 3.0 or later
Browser Restrictions
•
If you are using Internet Explorer 6, you cannot directly use an IPv6 address
to access the WAP device. You can, however, use the Domain Name System
(DNS) server to create a domain name that contains the IPv6 address, and
then use that domain name in the address bar in place of the IPv6 address.
•
When using Internet Explorer 8, you can configure security settings from
Internet Explorer. Select Tools > Internet Options and then select the
Security tab. Select Local Intranet and select Sites. Select Advanced and
then select Add. Add the intranet address of the WAP device (http://<ip-
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
7
Getting Started
Starting the Web-Based Configuration Utility
1
address>) to the local intranet zone. The IP address can also be specified
as the subnet IP address, so that all addresses in the subnet are added to
the local intranet zone.
•
If you have multiple IPv6 interfaces on your management station, use the
IPv6 global address instead of the IPv6 local address to access the WAP
device from your browser.
Launching the Web-Based Configuration Utility
To open the configuration utility:
STEP 1 Open a web browser.
Enter the IP address of the WAP device that you are configuring in the address bar
on the browser and then press Enter. The Login page opens.
•
To find your IP address, you can use the Cisco FindIT Network Discovery
Utility. This tool enables you to automatically discover all supported Cisco
Small Business devices in the same local network segment as your
computer. For more information, go to cisco.com and enter www.cisco.com/
go/findit.
•
For further instructions on how to locate the IP address of your WAP device,
see the WAP device Quick Start Guide.
STEP 2 Enter the user name and password. The factory default user name is cisco and the
default password is cisco.
STEP 3 Click Log In. The Access Point Setup Wizard page opens.
If this is the first time that you logged on with the default user name (cisco) and the
default password (cisco) or your password has expired, the Change Admin
Password page opens. Enter the new password and confirm it, click Apply, and
then click Close. The new password is saved. Then, enter the user name cisco and
the new password on the Login page.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
8
Getting Started
Using the Access Point Setup Wizard
1
Logging Out
By default, the configuration utility logs out after 10 minutes of inactivity. See
To log out, click Logout in the top right corner of the configuration utility.
Using the Access Point Setup Wizard
The first time that you log into the WAP device (or after it has been reset to the
factory default settings), the Access Point Setup Wizard appears to help you
perform initial configurations. Follow these steps to complete the wizard:
NOTE If you click Cancel to bypass the Wizard, the Change Password page appears. You
can then change the default password for logging in. For all other settings, the
factory default configurations apply.
You must log in again after changing your password.
STEP 1 Click Next on the Welcome page of the Wizard. The Configure Device - IP
Address window appears.
STEP 2 Click Dynamic IP Address (DHCP) if you want the WAP device to receive an IP
address from a DHCP server. Or select Static IP Address to configure IP Address
STEP 3 Click Next. The Single Point Setup — Set a Cluster window appears. For a
STEP 4 To create a new Single Point Setup of WAP devices, select Create a New Cluster
and specify a New Cluster Name. When you configure your devices with the
same cluster name and enable Single Point Setup mode on other WAP devices,
they automatically join the group.
If you already have a cluster on your network, you can add this device to it by
clicking Join an Existing Cluster, and then entering the Existing Cluster Name.
If you do not want this device to participate in a Single Point Setup at this time,
click Do not Enable Single Point Setup.
(Optional) You can enter text in the AP Location field to note the physical location
of the WAP device.
STEP 5 Click Next. The Configure Device - Set System Date and Time window appears.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
9
Getting Started
Using the Access Point Setup Wizard
1
STEP 6 Select your time zone, and then set the system time manually or set up the WAP
device to get its time from an NTP server. For a description of these options, see
STEP 7 Click Next. The Enable Security - Set Password window appears.
STEP 8 Enter a New Password and enter it again in the Confirm Password text box. For
NOTE You can uncheck the Password Complexity box if you wish to disable
the password security rules. However, we strongly recommend keeping the
password security rules enabled.
STEP 9 Click Next. The Enable Security - Name Your Wireless Network window appears.
STEP 10 Enter a Network Name. This name serves as the SSID for the default wireless
network.
STEP 11 Click Next. The Enable Security - Secure Your Wireless Network window appears.
STEP 12 Choose a security encryption type and enter a security key. For a description of
STEP 13 Click Next. The Wizard displays the Enable Security- Assign the VLAN ID For Your
Wireless Network window.
STEP 14 Enter a VLAN ID for traffic received on the wireless network.
It is suggested that you assign a different VLAN ID from the default (1) to wireless
traffic, in order to segregate it from management traffic on VLAN 1.
STEP 15 Click Next.
For the WAP121 device, the Wizard displays the Summary - Confirm Your Settings
For the WAP321 device, the Wizard displays the Enable Captive Portal - Create
Your Guest Network window.
STEP 16 Select whether or not to set up an authentication method for guests on your
network (WAP321 only), and click Next.
If you click Yes, the Wizard displays the Enable Captive Portal - Name Your Guest
Network window.
STEP 17 Specify a Guest Network Name.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
10
Getting Started
Using the Access Point Setup Wizard
1
STEP 18 Click Next. The Wizard displays the Enable Captive Portal - Secure Your Guest
Network window.
STEP 19 Choose a security encryption type for the guest network and enter a security key.
STEP 20 Click Next. The Wizard displays the Enable Captive Portal - Assign the VLAN ID
window.
STEP 21 Specify a VLAN ID for the guest network. The guest network VLAN ID should be
different from the management VLAN ID.
STEP 22 Click Next. The Wizard displays the Enable Captive Portal - Enable Redirect URL
window.
STEP 23 Select Enable Redirect URL and specify a fully qualified domain name or IP
address in the Redirect URL field (including http://). If specified, guest network
users are redirected to the specified URL after authenticating.
STEP 24 Click Next. The Wizard displays the Summary - Confirm Your Settings window.
STEP 25 Review the settings that you configured. Click Back to reconfigure one or more
settings. If you click Cancel, all settings are returned to the previous or default
values.
STEP 26 If they are correct, click Submit. Your WAP setup settings are saved and a
confirmation window appears.
STEP 27 Click Finish. The Getting Started window appears.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
11
Getting Started
Getting Started
1
Getting Started
To simplify device configuration through quick navigation, the Getting Started
page provides links for performing common tasks. The Getting Started page is the
default window every time you log into the configuration utility.
Links on the Getting Started Page
Category
Link Name (on the Page)
Linked Page
Initial Setup
Run Setup Wizard
Configure Radio Settings
Configure LAN Settings
Run WPS
Configure Single Point Setup
System Summary
Device
Status
Wireless Status
Quick
Change Account Password
Upgrade Device Firmware
Backup/Restore Configuration
Access
Other
Support
Forums
A link to the Cisco WAP
support site.
Resources
A link to the Cisco
Support Community
site.
Wireless Planning Tool
A link to Fluke networks
AirMagnet Planner for
Cisco Small Business.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
12
Getting Started
Window Navigation
1
Window Navigation
This section describes the features of the configuration utility.
Configuration Utility Header
The Configuration Utility header contains standard information and appears at the
top on every page. It provides these buttons:
Buttons
Button Name
Description
(User)
The account name (Administrator or Guest) of the user
logged into the WAP device. The factory default user
name is cisco.
Log Out
About
Help
Click to log out of the configuration utility.
Click to show the WAP device type and version number.
Click to show the online help. The online help is designed
to be viewed with browsers using UTF-8 encoding. If the
online help shows errant characters, verify that the
encoding settings on your browser are set to UTF-8.
Navigation Pane
A navigation pane, or main menu, is located on the left side of each page. The
navigation pane is a list of the top-level features of the WAP devices. If a main
menu item is preceded by an arrow, select to expand and display the submenu of
each group. You can then select on the desired submenu item to open the
associated page.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
13
Getting Started
Window Navigation
1
Management Buttons
The table below describes the commonly used buttons that appear on various
pages in the system.
Management Buttons
Button Name
Add
Description
Adds a new entry to the table or database.
Cancels the changes made to the page.
Clears all entries in the log table.
Cancel
Clear All
Delete
Edit
Deletes an entry in a table. Select an entry first.
Edits or modifies an existing entry. Select an entry first.
Redisplays the current page with the latest data.
Saves the settings or configuration.
Refresh
Save
Update
Updates the new information to the startup
configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
14
2
Status and Statistics
This chapter describes how to display status and statistics and contains these
topics:
•
•
•
•
•
•
•
•
•
•
•
System Summary
The System Summary page shows basic information such as the hardware model
description, software version, and the time that has elapsed since the last reboot.
To view system information, select Status and Statistics > System Summary in
the navigation pane. Or, select System Summary under Device Status on the
Getting Started page.
The System Summary page shows this information:
•
PID VID—The WAP hardware model and version.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
15
Status and Statistics
System Summary
2
•
•
•
•
•
•
•
•
Serial Number—The serial number of the Cisco WAP device.
Base MAC Address—The WAP MAC address.
Firmware Version—The firmware version number of the active image.
Firmware MD5 Checksum—The checksum for the active image.
Host Name—A name assigned to the device.
System Uptime—The time that has elapsed since the last reboot.
System Time—The current system time.
Power Source—The system may be powered by a power adapter, or may
be receiving power-over-Ethernet from PoE power-sourcing equipment
(PSE).
The TCP/UDP Service table shows basic information about protocols and
services operating on the WAP.
•
•
Service—The name of the service, if available.
Protocol—The underlying transport protocol that the service uses (TCP or
UDP).
•
Local IP Address—The IP address, if any, of a remote device that is
connected to this service on the WAP device. All indicates that any IP
address on the device can use this service.
•
•
Local Port—The port number for the service.
Remote IP Address—The IP address of a remote host, if any, that is using
this service. All indicates that the service is available to all remote hosts that
access the system.
•
•
Remote Port—The port number of any remote device communicating with
this service.
Connection State—The state of the service. For UDP, only connections in
the Active state appear in the table. In the Active state, a connection is
established between the WAP device and a client or server. The TCP states
are:
-
-
Listening—The service is listening for connection requests.
Active—A connection session is established and packets are being
transmitted and received.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
16
Status and Statistics
Network Interfaces
2
-
-
Established—A connection session is established between the WAP
device and a server or client, depending on the role of each device with
respect to this protocol.
Time Wait—The closing sequence has been initiated and the WAP is
waiting for a system-defined timeout period (typically 60 seconds)
before closing the connection.
You can click Refresh to refresh the screen and show the most current information.
Network Interfaces
Use the Network Interfaces page to show configuration and status information
about the wired and wireless interfaces. To show the Network Interfaces page,
select Status and Statistics > Network Interface in the navigation pane.
The Network Interfaces page shows this information:
•
LAN Status—These settings apply to the internal interface. For the
WAP321, the information indicates whether or not Green Ethernet mode is
enabled.
To change any of these settings, click the Edit link. After you click Edit, you
are redirected to the VLAN and IPv4 Address Settings page. See VLAN and
IPv4 Address Settings for descriptions of these fields.
•
•
Radio Status—These settings include the Wireless Radio mode (Enabled
or Disabled), the MAC address associated with the radio interface, the
802.11 mode (a/b/g/n), and the channel used by the interface.
To change the wireless settings, click the Edit link. After you click Edit, you
Interface Status—This table lists status information for each Virtual Access
Point (VAP) and on each Wireless Distribution System (WDS) interface.
If the VAP has been configured, the table lists the SSID, the administrative
status (up or down), the MAC address of the radio interface, the VLAN ID,
the name of any associated scheduler profile, and the current state (active
or inactive). The state indicates whether the VAP is exchanging data with a
client.
You can click Refresh to refresh the screen and show the most current information.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
17
Status and Statistics
Traffic Statistics
2
Traffic Statistics
Use the Traffic Statistics page to view basic information about the WAP. It also
provides a real-time display of transmit and receive statistics for the Ethernet
interface, the Virtual Access Points (VAPs), and any WDS interfaces. All transmit
and receive statistics reflect the totals since the WAP was last started. If you
reboot the WAP, these figures indicate transmit and receive totals since the reboot.
To show the Traffic Statistics page, select Status and Statistics > Traffic
Statistics in the navigation pane.
The Traffic Statistics page shows summary data and statistics for traffic in each
direction.
•
Network Interface—Name of the Ethernet interface and each VAP and
WDS interface.
Each VAP interface name is followed by its SSID in parentheses.
•
•
•
•
•
Total Packets—The total packets sent (in Transmit table) or received (in
Received table) by this WAP device.
Total Bytes—The total bytes sent (in Transmit table) or received (in
Received table) by this WAP device.
Total Dropped Packets—The total number of dropped packets sent (in
Transmit table) or received (in Received table) by this WAP device.
Total Dropped Bytes—The total number of dropped bytes sent (in Transmit
table) or received (in Received table) by this WAP device.
Errors—The total number of errors related to sending and receiving data on
this WAP device.
You can click Refresh to refresh the screen and show the most current information.
WorkGroup Bridge Transmit/Receive
The WorkGroup Bridge Transmit/Receive page shows packet and byte counts for
traffic between stations on a WorkGroup Bridge. For information on configuring
To show the WorkGroup Bridge Transmit/Receive page, select Status and
Statistics > WorkGroup Bridge in the navigation pane.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
18
Status and Statistics
Associated Clients
2
Each network interface that is configured as a WorkGroup Bridge interface shows
these fields:
•
•
Network Interface—Name of the Ethernet or VAP interface.
Status and Statistics—Whether the interface is disconnected or is
administratively configured as up or down.
•
•
VLAN ID—Virtual LAN (VLAN) ID. You can use VLANs to establish multiple
internal and guest networks on the same WAP device. The VLAN ID is set on
Name (SSID)—Wireless network name. Also known as the SSID, this
alphanumeric key uniquely identifies a wireless local area network. The
Additional information appears for the transmit and receive direction for each
WorkGroup Bridge interface:
•
Total Packets—The total number of packets bridged between the wired
clients in the WorkGroup Bridge and the wireless network.
•
Total Bytes—The total number of bytes bridged between the wired clients
in the WorkGroup Bridge and the wireless network.
You can click Refresh to refresh the screen and show the most current information.
Associated Clients
You can use the Associated Clients page to view the client stations associated
with a particular access point.
To show the Associated Clients page, select Status and Statistics > Associated
Clients in the navigation pane.
The associated stations are shown along with information about packet traffic
transmitted and received for each station.
•
Total Number of Associated Clients—The total number of clients currently
associated with the WAP device.
•
•
Network Interface—The VAP the client is associated with.
Station—The MAC address of the associated wireless client.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
19
Status and Statistics
Associated Clients
2
•
Status—The Authenticated and Associated Status shows the underlying
IEEE 802.11 authentication and association status, which is present no
matter which type of security the client uses to connect to the WAP device.
This status does not show IEEE 802.1X authentication or association status.
These are some points to keep in mind with regard to this field:
-
If the WAP device security mode is None or Static WEP, the
authentication and association status of clients appears as expected;
that is, if a client shows as authenticated to the WAP device, it is able to
transmit and receive data. (The reason why is that Static WEP uses only
IEEE 802.11 authentication.)
-
If the WAP device uses IEEE 802.1X or WPA security, it is possible for a
client association to appear as authenticated (through IEEE 802.11
security) although it is not actually authenticated through the second
layer of security.
•
From Station/To Station—For the From Station, the counters indicate the
packets or bytes received by the wireless client. For the To Station, the
counters indicate the number of packets and bytes transmitted from the
WAP device to the wireless client.
-
Packets—Number of packets received (transmitted) from the wireless
client.
-
-
Bytes—Number of bytes received (transmitted) from the wireless client.
Drop Packets—Number of packets dropped after being received
(transmitted).
-
-
Drop Bytes—Number of bytes that dropped after being received
(transmitted).
TS Violate Packets (From Station)—Number of packets sent from a
client STA to the WAP device in excess of its active Traffic Stream (TS)
uplink bandwidth, or for an access category requiring admission control
to which the client STA has not been admitted.
-
TS Violate Packets (To Station)—Number of packets sent from the
WAP device to a client STA in excess of its active TS downlink
bandwidth, or for an access category requiring admission control to
which the client STA has not been admitted.
•
Up Time—The amount of time the client has been associated with the WAP
device.
You can click Refresh to refresh the screen and show the most current information.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
20
Status and Statistics
TSPEC Client Associations
2
TSPEC Client Associations
The TSPEC Client Associations page provides real-time information about the
TSPEC client data transmitted and received by this access point. The tables on
the TSPEC Client Associations page show voice and video packets transmitted
and received since the association started, along with status information.
A TSPEC is a traffic specification that is sent from a QoS-capable wireless client to
a WAP device requesting a certain amount of network access for the Traffic
Stream (TS) it represents. A traffic stream is a collection of data packets identified
by the wireless client as belonging to a particular user priority. An example of a
voice traffic stream is a Wi-Fi CERTIFIED telephone handset that marks its codec-
generated data packets as voice priority traffic. An example of a video traffic
stream is a video player application on a wireless laptop that prioritizes a video
conference feed from a corporate server.
To view TSPEC client association statistics, select Status and Statistics > TSPEC
Client Associations in the navigation pane.
The TSPEC Client Associations page shows this information:
Status and Statistics:
•
•
•
•
•
•
Network Interface—Radio interface used by the client.
SSID—Service set identifier associated with this TS client.
Station—Client station MAC address.
TS Identifier—TSPEC Traffic Session Identifier (range 0 to 7).
Access Category—TS Access Category (voice or video).
Direction—Traffic direction for this TS. Direction can be one of these
options:
-
-
-
uplink—From client to device.
downlink—From device to client.
bidirectional
•
User Priority—User Priority (UP) for this TS. The UP is sent with each
packet in the UP portion of the IP header. Typical values are as follows:
-
-
6 or 7 for voice
4 or 5 for video
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
21
Status and Statistics
TSPEC Client Associations
2
The value may differ depending on other priority traffic sessions.
•
•
Medium Time—Time that the TS traffic occupies the transmission medium.
Excess Usage Events—Number of times that the client has exceeded the
medium time established for its TSPEC. Minor, infrequent violations are
ignored.
•
VAP MAC Address—Virtual Access Point MAC address.
Statistics:
•
•
•
•
•
Network Interface—Radio interface used by the client.
Station—Client station MAC address.
TS Identifier—TSPEC Traffic Session Identifier (range 0 to 7).
Access Category—TS Access Category (voice or video).
Direction—The traffic direction for this TS. Direction can be one of these
options:
-
-
-
uplink—From client to device.
downlink—From device to client.
bidirectional
•
From Station—Shows the number of packets and bytes received from the
wireless client and the number of packets and bytes that were dropped
after being received.
-
-
Packets—Number of packets in excess of an admitted TSPEC.
Bytes—Number of bytes when no TSPEC has been established and
admission is required by the WAP device.
•
To Station—The number of packets and bytes transmitted from the WAP
device to the wireless client and the number of packets and bytes that were
dropped upon transmission.
-
-
Packets—Number of packets in excess of an admitted TSPEC.
Bytes—Number of bytes for which no TSPEC has been established
when admission is required by the WAP device.
You can click Refresh to refresh the screen and show the most current information.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
22
Status and Statistics
TSPEC Status and Statistics
2
TSPEC Status and Statistics
The TSPEC Status and Statistics page provides this information:
•
•
•
Summary information about TSPEC sessions by radio.
Summary information about TSPEC sessions by VAP.
Real-time transmit and receive statistics for the radio interface and the
network interface(s).
All of the transmit and receive statistics shown are totals since the WAP device
was last started. If you reboot the WAP device, these figures indicate transmit and
receive totals since the reboot.
To view TSPEC status and statistics, select Status and Statistics > TSPEC Status
and Statistics in the navigation pane.
The TSPEC Status and Statistics page provides this status information for the
WLAN (Radio) and VAP interfaces:
•
•
Network Interface—Name of the Radio or VAP interface.
Access Category—Current Access Category associated with this Traffic
Stream (voice or video).
•
Status—Whether the TSPEC session is enabled (up) or not (down) for the
corresponding Access Category.
NOTE Status is a configuration status (it does not necessarily represent the
current session activity).
•
•
•
Active Traffic Stream—Number of currently active TSPEC Traffic Streams
for this radio and Access Category.
Traffic Stream Clients—Number of Traffic Stream clients associated with
this radio and Access Category.
Medium Time Admitted—Time allocated for this Access Category over the
transmission medium to carry data. This value should be less than or equal
to the maximum bandwidth allowed over the medium for this TS.
•
Medium Time Unallocated—Time of unused bandwidth for this Access
Category.
These statistics appear separately for the transmit and receive paths on the
wireless radio interface:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
23
Status and Statistics
TSPEC AP Statistics
2
•
•
Access Category—The Access Category associated with this Traffic
Stream (voice or video).
Total Packets—Total number of TS packets sent (in Transmit table) or
received (in Received table) by this Radio for the specified Access
Category.
•
Total Bytes—Total number of bytes received in the specified access
category.
These statistics appear separately for the transmit and receive paths on the
network interfaces (VAPs):
•
•
•
•
Total Voice Packets—Total number of TS voice packets sent (in Transmit
table) or received (in Received table) by this WAP device for this VAP.
Total Voice Bytes—Total TS voice bytes sent (in Transmit table) or received
(in Received table) by this WAP device for this VAP.
Total Video Packets—Total number of TS video packets sent (in Transmit
table) or received (in Received table) by this WAP device for this VAP.
Total Video Bytes—Total TS video bytes sent (in Transmit table) or
received (in Received table) by this WAP device for this VAP.
You can click Refresh to refresh the screen and show the most current information.
TSPEC AP Statistics
The TSPEC AP Statistics page provides information on the voice and video Traffic
Streams accepted and rejected by the WAP device. To view the TSPEC AP
Statistics page, select Status and Statistics > TSPEC AP Statistics in the
navigation pane.
•
TSPEC Statistics Summary for Voice ACM—The total number of
accepted and the total number of rejected voice traffic streams.
•
TSPEC Statistics Summary for Video ACM—The total number of
accepted and the total number of rejected video traffic streams.
You can click Refresh to refresh the screen and show the most current information.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
24
Status and Statistics
Radio Statistics
2
Radio Statistics
You can use the Radio Statistics page to show packet-level and byte-level
statistics for the wireless radio interface. To view the Radio Statistics page, select
Status and Statistics > Radio Statistics in the navigation pane.
•
•
•
•
•
Packets Received—Total packets received by the WAP device.
Packets Transmitted—Total packets transmitted by the WAP device.
Bytes Received—Total bytes received by the WAP device.
Bytes Transmitted—Total bytes transmitted by the WAP device.
Packets Receive Dropped—Number of packets received by the WAP
device that were dropped.
•
•
•
•
•
•
•
•
•
Packets Transmit Dropped—Number of packets transmitted by the WAP
device that were dropped.
Bytes Receive Dropped—Number of bytes received by the WAP device
that were dropped.
Bytes Transmit Dropped—Number of bytes transmitted by the WAP
device that were dropped.
Fragments Received—Number of fragmented frames received by the
WAP device.
Fragments Transmitted—Number of fragmented frames sent by the WAP
device.
Multicast Frames Received—Count of MSDU frames received with the
multicast bit set in the destination MAC address.
Multicast Frames Transmitted—Count of successfully transmitted MSDU
frames where the multicast bit was set in the destination MAC address.
Duplicate Frame Count—Number of times a frame was received and the
Sequence Control field indicates it was a duplicate.
Failed Transmit Count—Number of times an MSDU was not transmitted
successfully due to transmit attempts exceeding either the short retry limit
or the long retry limit.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
25
Status and Statistics
Email Alert Status
2
•
•
FCS Error Count—Count of FCS errors detected in a received MPDU
frame.
Transmit Retry Count—Number of times an MSDU is successfully
transmitted after one or more retries.
•
•
ACK Failure Count—Count of ACK frames not received when expected.
RTS Failure Count—Count of CTS frames not received in response to an
RTS frame.
•
WEP Undecryptable Count—Number of frames discarded because they
could not be decrypted by the radio. Frames can be discarded because the
frame was not encrypted, or it was encrypted with a privacy option not
supported by the WAP device.
•
•
•
RTS Success Count—Count of CTS frames received in response to an
RTS frame.
Multiple Retry Count—Number of times an MSDU is successfully
transmitted after more than one retry.
Frames Transmitted Count—Count of each successfully transmitted
MSDU.
You can click Refresh to refresh the screen and show the most current information.
Email Alert Status
The Email Alert Status page provides information about the email alerts sent
based on the syslog messages generated in the WAP device. To view the Email
Alert Status page, select Status and Statistics > Email Alert Status in the
navigation pane.
•
•
•
•
Email Alert Status—The Email Alert configured status. The status is either
Enabled or Disabled. The default is Disabled.
Number of Emails Sent—The total number of emails sent. The range is an
unsigned integer of 32 bits. The default is 0.
Number of Emails Failed—The total number of email failures. The range is
an unsigned integer of 32 bits. The default is 0.
Time Last Email Sent—The day, date, and time when the last email was
sent.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
26
Status and Statistics
Log
2
Log
The Log page shows a list of system events that generated a log entry, such as
login attempts and configuration changes. The log is cleared upon a reboot and
can be cleared by an administrator. Up to 512 events can be shown. Older entries
are removed from the list as needed to make room for new events.
To view the Log page, select Status and Statistics > Log Status in the navigation
pane.
•
•
•
•
Time Stamp—The system time when the event occurred.
Severity—Whether the event is due to an error (err) or is informational (info).
Service—The software component associated with the event.
Description—A description of the event.
You can click Refresh to refresh the screen and show the most current information.
You can click Clear All to clear all entries from the log.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
27
Administration
System Settings
3
System Settings
The System Settings page enables you to configure information that identifies the
WAP device within the network.
To configure system settings:
STEP 1 Select Administration > System Settings in the navigation pane.
STEP 2 Enter the parameters:
•
Host Name—Administratively assigned name for the WAP device. By
convention, the name is the fully qualified domain name of the node. The
default host name is wap concatenated with the last 6 hex digits of the MAC
address of the WAP device. Host Name labels can contain only letters, digits
and hyphens. Host Name labels cannot begin or end with a hyphen. No other
symbols, punctuation characters, or blank spaces are permitted. The Host
Name can be 1 to 63 characters long.
•
•
System Contact—A contact person for the WAP device. The System
Contact can be 0 to 255 characters long and can include spaces and special
characters.
System Location—Description of the physical location of the WAP device.
The System Location can be 0 to 255 characters long and can include
spaces and special characters.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
User Accounts
One management user is configured on the WAP device by default:
•
•
User Name: cisco
Password: cisco
You can use the User Accounts page to configure up to four additional users and to
change a user password.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
29
Administration
User Accounts
3
Adding a User
To add a new user:
STEP 1 Select Administration > User Accounts in the navigation pane.
The User Account Table shows the currently configured users. The user cisco is
preconfigured in the system to have Read/Write privileges.
All other users can have Read Only Access, but not Read/Write access.
STEP 2 Click Add. A new row of text boxes appears.
STEP 3 Check the box for the new user and select Edit.
STEP 4 Enter a User Name between 1 to 32 alphanumeric characters. Only numbers 0 to
9 and letters a to z (upper or lower) are allowed for user names.
STEP 5 Enter a New Password between 1 and 64 characters and then enter the same
password in the Confirm New Password text box.
As you enter a password, the number and color of vertical bars changes to
indicate the password strength, as follows:
•
•
Red—The password fails to meet the minimum complexity requirements.
Orange—The password meets the minimum complexity requirements but
the password strength is weak.
•
Green—The password is strong.
STEP 6 Click Save. The changes are saved to the Startup Configuration.
NOTE To delete a user, select the check box next to the user name and select Delete. To
save your deletion permanently, select Save when complete.
Changing a User Password
To change a user password:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
30
Administration
Time Settings
3
STEP 1 Select Administration > User Accounts in the navigation pane.
The User Account Table shows the currently configured users. The user cisco is
preconfigured in the system to have Read/Write privileges. The password for the
user cisco can be changed.
STEP 2 Select the user to configure and click Edit.
STEP 3 Enter a New Password between 1 and 64 characters and then enter the same
password in the Confirm New Password text box.
As you enter a password, the number and color of vertical bars changes to
indicate the password strength, as follows:
•
•
Red—The password fails to meet the minimum complexity requirements.
Orange—The password meets the minimum complexity requirements but
the password strength is weak.
•
Green—The password is strong.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
NOTE If you change your password, you must log in again to the system.
Time Settings
A system clock provides a network-synchronized time-stamping service for
software events such as message logs. You can configure the system clock
manually or configure the WAP device as a Network Time Protocol (NTP) client
that obtains the clock data from a server.
Use the Time Settings page to set the system time manually or to configure the
system to acquire its time settings from a preconfigured NTP server. By default,
the WAP device is configured to obtain its time from a predefined list of NTP
servers.
The current system time appears at the top of the page, along with the System
Clock Source option.
To use NTP to have the WAP device automatically acquire its time settings:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
31
Administration
Time Settings
3
STEP 1 For the System Clock Source field, select Network Time Protocol (NTP).
STEP 2 Configure these parameters:
•
NTP Server/IPv4/IPv6 Address Name—Specify the IPv4 address, IPv6
address, or hostname of an NTP server. A default NTP server is listed.
A hostname can consist of one or more labels, which are sets of up to 63
alphanumeric characters. If a hostname includes multiple labels, each is
separated by a period (.). The entire series of labels and periods can be up
to 253 characters long.
•
Time Zone—Select the time zone for your location.
STEP 3 Select Adjust Time for Daylight Savings if daylight savings time is applicable to
your time zone. When selected, configure these fields:
•
•
•
Daylight Savings Start—Select the week, day, month, and time when
daylight savings time starts.
Daylight Savings End—Select the week, day, month, and time when
daylight savings time ends.
Daylight Savings Offset—Specify the number of minutes to move the clock
forward when daylight savings time begins and backward when it ends.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
To manually configure the time settings:
STEP 1 For the System Clock Source field, select Manually.
STEP 2 Configure these parameters:
•
•
•
System Date—Select the current month, day, and year date from the drop-
down lists.
System Time—Select the current hour and minutes in 24-hour clock format,
such as 22:00:00 for 10 p.m.
Time Zone—Select the time zone for your location.
STEP 3 Select Adjust Time for Daylight Savings if daylight savings time is applicable to
your time zone. When selected, configure these fields:
•
Daylight Savings Start—Select the week, day, month, and time when
daylight savings time starts.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
32
Administration
Log Settings
3
•
•
Daylight Savings End—Select the week, day, month, and time when
daylight savings time ends.
Daylight Savings Offset—Specify the number of minutes to move the clock
forward when daylight savings time begins and backward when it ends.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
Log Settings
You can use the Log Settings page to enable log messages to be saved in
permanent memory. You can also send logs to a remote host.
Configuring the Persistent Log
If the system unexpectedly reboots, log messages can be useful to diagnose the
cause. However, log messages are erased when the system reboots unless you
enable persistent logging.
!
CAUTION Enabling persistent logging can wear out the flash (nonvolatile) memory and
degrade network performance. Only enable persistent logging to debug a
problem. Make sure that you disable persistent logging after you finish debugging
the problem.
To configure persistent logging:
STEP 1 Select Administration > Log Settings in the navigation pane.
STEP 2 Configure the parameters:
•
Persistence—Click Enable to save system logs to nonvolatile memory so
that the logs are kept when the WAP device reboots. You can save up to 128
log messages in the nonvolatile memory. When the limit of 128 is reached,
the oldest log message is overwritten by the newest message. Clear this
field to save system logs to volatile memory. Logs in volatile memory are
deleted when the system reboots.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
33
Administration
Log Settings
3
•
•
Severity—The minimum severity that an event must have for it to be written
to the log in nonvolatile memory. For example, if you specify 2 (critical), then
critical, alert, and emergency events are logged to nonvolatile memory. Error
messages with a severity level of 3 to 7 are written to volatile memory.
Depth—The maximum number of messages, up to 512, that can be stored in
volatile memory. When the number you configure in this field is reached, the
oldest log event is overwritten by the newest log event. Note that the
maximum number of log messages that can be stored in nonvolatile memory
(the persistent log) is 128, which is not configurable.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
Remote Log Server
The Kernel Log is a comprehensive list of system events (shown in the System
Log) and kernel messages such as error conditions.
You cannot view kernel log messages directly from the web interface. You must
first set up a remote log server to receive and capture logs. Then you can
configure the WAP device to log to the remote log server.
Remote log server collection for WAP device syslog messages provides these
features:
•
•
•
Allows aggregation of syslog messages from multiple APs
Stores a longer history of messages than is kept on a single WAP device
Triggers scripted management operations and alerts
To specify a host on your network to serve as a remote log server:
STEP 1 Select Administration > Log Settings in the navigation pane.
STEP 2 Configure the parameters:
•
Remote Log—Enables the WAP device to send log messages to a remote
host. When disabled, all log messages are kept on the local system.
•
Server IPv4/IPv6 Address/Name—The IPv4 or IPv6 address, or the
hostname of the remote log server.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
34
Administration
Email Alert
3
A hostname can consist of one or more labels, which are sets of up to 63
alphanumeric characters. If a hostname includes multiple labels, each is
separated by a period (.). The entire series of labels and periods can be up
to 253 characters long.
•
UDP Port—The logical port number for the syslog process on the remote
host. The range is from 1 to 65535. The default port is 514.
Using the default port is recommended. If you choose to reconfigure the log
port, make sure that the port number you assign to syslog is available for use.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
If you enabled a Remote Log host, clicking Save activates remote logging. The
WAP device sends its kernel messages real-time for display to the remote log
server monitor, a specified kernel log file, or other storage, depending on your
configurations.
If you disabled a Remote Log host, clicking Save disables remote logging.
NOTE After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
Email Alert
Use the email alert feature to send messages to the configured email addresses
when particular system events occur.
The feature supports mail server configuration, message severity configuration,
and up to three email address configurations to send urgent and non-urgent email
alerts.
TIP Do not use your personal email address, which would unnecessarily expose your
personal email login credentials. Use a separate email account instead. Also be
aware that many email accounts keep a copy of all sent messages by default.
Anyone with access to this email account has access to the sent messages.
Review your email settings to ensure that they are appropriate for the privacy
policy of your business.
To configure the WAP device to send email alerts:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
35
Administration
Email Alert
3
STEP 1 Select Administration > Email Alert in the navigation pane.
STEP 2 In the Global Configuration area, configure these parameters:
•
•
Administrative Mode—Choose to enable the email alert feature globally.
From Email Address—Enter the address to show as the sender of the email.
The address is a 255 character string with only printable characters. No
address is configured by default.
•
•
Log Duration—Choose the frequency at which scheduled messages are
sent. The range is from 30 to 1440 minutes. The default is 30 minutes.
Scheduled Message Severity—Log messages of this severity level or
higher are grouped and sent to the configuration email address at the
frequency specified by the Log Duration. Select from these values: None,
Emergency, Alert, Critical, Error, Warning, Notice, Info, and Debug. If set to
None, then no scheduled severity messages are sent. The default severity is
Warning.
•
Urgent Message Severity—Log messages of this severity level or higher
are sent to the configured email address immediately. Select from these
values: None, Emergency, Alert, Critical, Error, Warning, Notice, Info, and
Debug. If set to None, then no urgent severity messages are sent. The default
is Alert.
STEP 3 In the Mail Server Configuration area, configure these parameters:
•
Server IPv4 Address/Name—Enter the IP address or hostname of the
outgoing SMTP server. (You can check with your email provider for the
hostname.) The server address must be a valid IPv4 address or hostname.
The IPv4 address should be in a form similar to xxx.xxx.xxx.xxx (192.0.2.10).
A hostname can consist of one or more labels, which are sets of up to 63
alphanumeric characters. If a hostname includes multiple labels, each is
separated by a period (.). The entire series of labels and periods can be up
to 253 characters long.
•
•
Data Encryption—Enter the mode of security for the outbound email alert.
The alert can be sent using secure TLS protocol or the default Open
protocol. Using secure TLSv1 protocol can prevent eavesdropping and
tampering during the communication across the public network.
Port—Enter the SMTP port number to use for outbound emails. The range is
a valid port number from 0 to 65535. The default port is 465. The port
generally depends on the mode used by the email provider.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
36
Administration
Email Alert
3
•
•
Username—Enter the username for the email account that will be used to
send these emails. Typically (but not always) the username is the full email
address including the domain (such as [email protected]). The specified
account will be used as the email address of the sender. The username can
be from 1 to 64 alphanumeric characters.
Password—Enter the password for the email account that will be used to
send these emails. The password can be from 1 to 64 characters.
STEP 4 Configure the email addresses and subject line.
•
To Email Address 1/2/3—Enter up to three addresses to receive email
alerts. Each email address must be valid.
•
Email Subject—Enter the text to appear in the email subject line. This can be
up to a 255 character alphanumeric string.
STEP 5 Click Te s t M a i l to send a test email to validate the configured email account.
STEP 6 Click Save. The changes are saved to the Startup Configuration.
Email Alert Examples
The following example shows how to fill in the Mail Server Configuration
parameters:
Gmail
Server IPv4 Address/Name = smtp.gmail.com
Data Encryption = TLSv1
Port = 465
Username = Your full email address you can use to login to your email account
associated with the above server
Password = xxxxxxxx is a valid password of your valid email account
To Email Address 1 = [email protected]
Windows Live Hotmail
Windows Live Hotmail recommends the following settings:
Data Encryption: TLSv1
SMTP Server: smtp.live.com
SMTP Port: 587
Username: Your full email address, such as [email protected] or
Password: Your Windows Live account password
Yahoo! Mail
Yahoo requires using a paid account for this type of service. Yahoo
recommends the following settings:
Data Encryption: TLSv1
SMTP Server: plus.smtp.mail.yahoo.com
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
37
Administration
HTTP/HTTPS Service
3
SMTP Port: 465 or 587
Username: Your email address, without the domain name such as myName (without
@yahoo.com)
Password: Your Yahoo account password
The following example shows a sample format of a general log email:
From: [email protected]
Sent: Wednesday, September 09, 2009 11:16 AM
Subject: log message from AP
TIME
PriorityProcess Id
Message
Sep 8 03:48:25 info
Sep 8 03:48:26 info
reached
login[1457]
root login on ttyp0
mini_http-ssl[1175] Max concurrent connections of 20
HTTP/HTTPS Service
Use the HTTP/HTTPS Service page to enable and configure web-based
management connections. If HTTPS is used for secure management sessions, you
also use the HTTP/HTTPS Service page to manage the required SSL certificates.
Configuring HTTP and HTTPS Services
To configure HTTP and HTTP services:
STEP 1 Select Administration > HTTP/HTTPS Service in the navigation pane.
STEP 2 Configure these Global Settings:
•
Maximum Sessions—The number of web sessions, including both HTTP
and HTTPS, that can be in use at the same time.
When a user logs on to the WAP device configuration utility, a session is
created. This session is maintained until the user logs off or the Session
Timeout expires. The range is from 1 to 10 sessions. The default is 5. If the
maximum number of sessions is reached, the next user who attempts to log
on to the configuration utility receives an error message about the session
limit.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
38
Administration
HTTP/HTTPS Service
3
•
Session Timeout—The maximum amount of time, in minutes, an inactive
user remains logged on to the WAP device configuration utility. When the
configured timeout is reached, the user is automatically logged off. The
range is from 1 to 60 minutes. The default is 10 minutes.
STEP 3 Configure HTTP and HTTPS services:
•
•
•
•
•
HTTP Server—Enables access through HTTP. By default, HTTP access is
enabled. If you disable it, any current connections using that protocol are
disconnected.
HTTP Port—The logical port number to use for HTTP connections, from
1025 to 65535. The default port number for HTTP connections is the well-
known IANA port number 80.
HTTPS Server—Enables access through secure HTTP. By default, HTTPS
access is enabled. If you disable it, any current connections using that
protocol are disconnected.
HTTPS Port—The logical port number to use for HTTP connections, from
1025 to 65535. The default port number for HTTP connections is the well-
known IANA port number 443.
Redirect HTTP to HTTPS—Redirects management HTTP access attempts
on the HTTP port to the HTTPS port. This field is available only when HTTP
access is disabled.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
Managing SSL Certificates
To use HTTPS services, the WAP device must have a valid SSL certificate. The
WAP device can generate a certificate or you can download it from your network
or from a TFTP server.
To generate the certificate with the WAP device, click Generate SSL Certificate.
This should be done after the WAP device has acquired an IP address to ensure
that the common name for the certificate matches the IP address of the WAP
device. Generating a new SSL certificate restarts the secure web server. The
secure connection does not work until the new certificate is accepted on the
browser.
In the Certificate File Status area, you can view whether a certificate currently
exists on the WAP device, and view this information about it:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
39
Administration
Management Access Control
3
•
•
•
Certificate File Present
Certificate Expiration Date
Certificate Issuer Common Name
If an SSL certificate (with a .pem extension) exists on the WAP device, you can
download it to your computer as a backup. In the Download SSL Certificate (From
Device to PC) area, select HTTP or TFTP for the Download Method and click
Download.
•
If you select HTTP, you are prompted to confirm the download and then to
browse to the location to save the file on your network.
•
If you select TFTP, additional fields appear to enable you to enter the File
Name to assign to the downloaded file, and enter the TFTP server address
where the file will be downloaded.
You can also upload a certificate file (with a .pem extension) from your computer to
the WAP device. In the Upload SSL Certificate (From PC to Device) area, select
HTTP or TFTP for the Upload Method.
•
•
For HTTP, browse to the network location, select the file, and click Upload.
For TFTP, enter the File Name as it exists on the TFTP server and the TFTP
Server IPv4 Address, then click Upload. The filename cannot contain the
following characters: spaces, <, >, |, \, : , (, ), &, ; , #, ? , *, and two or more
successive periods.
A confirmation appears when the upload was successful.
Management Access Control
You can create an access control list (ACL) that lists up to five IPv4 hosts and five
IPv6 hosts that are authorized to access the WAP device configuration utility. If this
feature is disabled, anyone can access the configuration utility from any network
client by supplying the correct WAP device username and password.
If the management ACL is enabled, access through the web and SNMP is
restricted to the specified IP hosts.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
40
Administration
Upgrade Firmware
3
!
CAUTION Verify any IP address that you enter. If you enter an IP address that does not match
your Administrative computer, you will lose access to the configuration interface. It
is highly recommend to give the Administrative computer a static IP address, so the
address does not change over time.
To create an access list:
STEP 1 Select Administration > Management Access Control in the navigation pane.
STEP 2 Select Enable for the Management ACL Mode.
STEP 3 Enter up to five IPv4 and five IPv6 addresses that will be allowed access.
STEP 4 Verify the IP addresses are correct.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
Upgrade Firmware
As new versions of the WAP device firmware become available, you can upgrade
the firmware on your devices to take advantage of new features and
enhancements. The WAP device uses a TFTP or HTTP client for firmware
upgrades.
After you upload new firmware and the system reboots, the newly added
firmware becomes the primary image. If the upgrade fails, the original firmware
remains as the primary image.
NOTE When you upgrade the firmware, the access point retains the existing configuration
information.
TFTP Upgrade
To upgrade the firmware on an access point using TFTP:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
41
Administration
Upgrade Firmware
3
STEP 1 Select Administration > Update Firmware in the navigation pane.
The Product ID (PID) and active and inactive firmware versions appear.
STEP 2 Select TFTP for Transfer Method.
STEP 3 Enter a name (1 to 256 characters) for the image file in the Source File Name field,
including the path to the directory that contains the image to upload.
For example, to upload the ap_upgrade.tar image located in the /share/builds/ap
directory, enter: /share/builds/ap/ap_upgrade.tar
The firmware upgrade file supplied must be a tar file. Do not attempt to use bin
files or files of other formats for the upgrade; these types of files do not work.
The filename cannot contain the following items: spaces, <, >, |, \, : , (, ), &, ; , #, ? , *,
and two or more successive periods.
STEP 4 Enter the TFTP Server IPv4 Address and click Upgrade.
Uploading the new software may take several minutes. Do not refresh the page or
navigate to another page while uploading the new software, or the software
upload is aborted. When the process is complete the access point restarts and
resumes normal operation.
STEP 5 To verify that the firmware upgrade completed successfully, log into the user
interface and display the Upgrade Firmware page and view the active firmware
version.
HTTP Upgrade
To upgrade using HTTP:
STEP 1 Select HTTP for Transfer Method.
STEP 2 If you know the name and path to the new file, enter it in the Source File Name
field. Otherwise, click the Browse button and locate the firmware image file on
your network.
The firmware upgrade file supplied must be a tar file. Do not attempt to use bin
files or files of other formats for the upgrade; these types of files do not work.
STEP 3 Click Upgrade to apply the new firmware image.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
42
Administration
Firmware Recovery
3
Uploading the new software may take several minutes. Do not refresh the page or
navigate to another page while uploading the new software, or the software
upload is aborted. When the process is complete, the access point restarts and
resumes normal operation.
STEP 4 To verify that the firmware upgrade completed successfully, log into the user
interface, display the Upgrade Firmware page, and view the active firmware
version.
Firmware Recovery
The WAP device has a firmware recovery feature that enables the restoration of a
valid image on the WAP device after a failed download. If the power goes down
during an image download, the WAP device might not be able to boot. In this
event, although the image is not usable, the boot loader file that loads the firmware
image from flash memory to RAM should continue to be functional. An HTTP
server is embedded in the boot loader file, enabling the administrator to connect
to the WAP device over the LAN port and use a web browser to download and
install a new firmware image.
The WAP device enters the HTTP firmware recovery mode when it is booted and
the boot loader cannot find a valid image in flash memory. In this mode, the boot
loader sets the internal network port to the following static IP address:
•
•
•
IP Address: 192.168.1.254
Network Mask: 255.255.255.0
Default Gateway: 192.168.1.1
An HTTP server starts and listens for client connections on port 80.
NOTE The Firmware Recovery page is shown in the web-based configuration utility only
when an image needs to be restored.
To use this feature to download a new firmware image:
STEP 1 Directly connect a PC to the LAN port.
STEP 2 Configure the IP address and mask on the management PC to be in the same
subnet as the switch.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
43
Administration
Firmware Recovery
3
NOTE You can access the system across a network if the default gateway IP
address is 192.168.1.1.
STEP 3 Open a web browser and enter the IP address of the switch in the address bar
(192.168.1.254).
NOTE The HTTP firmware recovery features support the following
browsers:
-
-
Firefox 3.0 and later versions
Internet Explorer 6 and later versions
A Firmware Recovery page appears. No authentication is required.
The web page shows the PIC VID (product ID and vendor ID), serial number, and
MAC address of the WAP device.
STEP 4 Select Browse and select a valid firmware image to download.
A progress bar appears while the file is downloading. The following message
appears upon a successful download:
100% Complete
File downloaded successfully. Please wait while the file is being written to
flash. System will automatically reboot.
The file selected by administrator is downloaded to RAM and is validated for the
following conditions:
•
•
•
The CRC of the file is good.
The STK file is built for this platform.
The STK file size is within the partition limits (4.5 MB is reserved for this file).
If these conditions are met, the file is written to flash memory and the system is
rebooted using the new firmware.
If any of these checks fail, the image is not written to flash memory and the
recovery process is stopped. You can restart the recovery process with a correct
image file.
If the transfer is aborted because the browser window is refreshed or closed, the
session is cleared and the session times out immediately. If the transfer is aborted
because the network is unreachable, the session times out after 45 seconds. After
the session times out, you can begin the recovery process again.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
44
Administration
Download/Backup Configuration File
3
Download/Backup Configuration File
The WAP device configuration files are in XML format and contain all the
information about the WAP device settings. You can back up (upload) the
configuration files to a network host or TFTP server to manually edit the content or
create backups. After you edit a backed-up configuration file, you can download it
to the access point to modify the configuration.
The WAP device maintains these configuration files:
•
•
Startup Configuration—The configuration file saved to flash memory.
Backup Configuration—An additional configuration file saved on the WAP
device for use as a backup.
•
Mirror Configuration—If the Startup Configuration is not modified for at
least 24 hours, it is automatically saved to a Mirror Configuration file. The
Mirror Configuration file is a snapshot of a past Startup Configuration. The
Mirror Configuration is preserved across factory resets, so it can be used to
recover a system configuration after a factory reset by copying the Mirror
Configuration to the Startup Configuration.
NOTE In addition to downloading and uploading these files to another system, you can
copy them to different file types on the WAP device. See Copy/Save
Backing Up a Configuration File
To back up (upload) the configuration file to a network host or TFTP server:
STEP 1 Select Administration > Download/Backup Configuration File in the navigation
pane.
STEP 2 Select Via TFTP or Via HTTP/HTTPS as the Transfer Method.
STEP 3 Select Backup (AP to PC) as the Save Action.
STEP 4 For a TFTP backup only, enter the Destination File Name with an .xml extension.
Also include the path where the file is to be placed on the server and then enter
the TFTP Server IPv4 Address.
The filename cannot contain the following characters: spaces, <, >, |, \, : , (, ), &, ; , #,
? , *, and two or more successive periods.
STEP 5 For a TFTP backup only, enter the TFTP Server IPv4 Address.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
45
Administration
Download/Backup Configuration File
3
STEP 6 Select which configuration file you want to back up:
•
Startup Configuration—Configuration file type used when the WAP device
last booted. This does not include any configuration changes applied but not
yet saved to the WAP device.
•
•
Backup Configuration—Backup configuration file type saved on the WAP
device.
Mirror Configuration—If the Startup Configuration is not modified for at
least 24 hours, it is automatically saved to a Mirror Configuration file. The
Mirror Configuration file is a snapshot of a past Startup Configuration. The
Mirror Configuration is preserved across factory resets, so it can be used to
recover a system configuration after a factory reset by copying the Mirror
Configuration to the Startup Configuration.
STEP 7 Click Save to begin the backup. For HTTP backups, a window appears to enable
you to browse to the desired location for saving the file.
Downloading a Configuration File
You can download a file to the WAP device to update the configuration or to
restore the WAP device to a previously backed-up configuration.
To download a configuration file to the WAP device:
STEP 1 Select Administration > Download/Backup Configuration File in the navigation
pane.
STEP 2 Select Via TFTP or Via HTTP/HTTPS as the Transfer Method.
STEP 3 Select Download (PC to AP) as the Save Action.
STEP 4 For a TFTP download only, enter the Source File Name with an .xml extension.
Include the path (where the file exists on the server) and enter the TFTP Server
IPv4 Address.
The filename cannot contain the following characters: spaces, <, >, |, \, : , (, ), &, ; , #,
? , *, and two or more successive periods.
STEP 5 Select which configuration file on the WAP device that you want replaced with the
downloaded file: the Startup Configuration or the Backup Configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
46
Administration
Configuration Files Properties
3
If the downloaded file overwrites the Startup Configuration file, and the file passes
a validity check, then the downloaded configuration takes effect the next time the
WAP device reboots.
STEP 6 Click Save to begin the upgrade or backup. For HTTP downloads, a window
appears to enable you to browse to select the file to download. When the
download is finished, a window indicates success.
!
CAUTION Ensure that power to the WAP device remains uninterrupted while the configuration
file is downloading. If a power failure occurs while downloading the configuration
file, the file is lost and the process must be restarted.
Configuration Files Properties
The Configuration Files Properties page enables you to clear the Startup or
Backup Configuration file. If you clear the Startup Configuration file, the Backup
Configuration file becomes active the next time that you reboot the WAP device.
To delete the Startup Configuration or Backup Configuration file:
STEP 1 Select Administration > Configuration Files Properties in the navigation pane.
STEP 2 Select the Startup Configuration, or Backup Configuration file type.
STEP 3 Click Clear Files.
Copy/Save Configuration
The Copy/Save Configuration page enables you to copy files within the WAP
device file system. For example, you can copy the Backup Configuration file to the
Startup Configuration file type, so that it is used the next time you boot up the
WAP device.
To copy a file to another file type:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
47
Administration
Reboot
3
STEP 1 Select Administration > Copy/Save Configuration in the navigation pane.
STEP 2 Select the Source File Name:
•
Startup Configuration—Configuration file type used when the WAP device
last booted. This does not include any configuration changes applied but not
yet saved to the WAP device.
•
•
Backup Configuration—Backup configuration file type saved on the WAP
device.
Mirror Configuration—If the Startup Configuration is not modified for at
least 24 hours, it is automatically saved to a Mirror Configuration file. The
Mirror Configuration file is a snapshot of a past Startup Configuration. The
Mirror Configuration is preserved across factory resets, so it can be used to
recover a system configuration after a factory reset by copying the Mirror
Configuration to the Startup Configuration.
STEP 3 For the Destination File Name, select the file type to be replaced with the file you
are copying.
STEP 4 Click Save to begin the copy process.
When complete, a window shows the message, Copy Operation Successful.
Reboot
You can use the Reboot page reboot the WAP device.
STEP 1 To reboot the WAP, select Administration > Reboot in the navigation pane.
STEP 2 Select one of these options:
•
•
Reboot—Reboots the WAP using Startup Configuration.
Reboot to Factory Default—Reboots the WAP using the factory default
configuration file. Any customized settings are lost.
A window appears to enable you to confirm or cancel the reboot. The current
management session might be terminated.
STEP 3 Click OK to reboot.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
48
Administration
Discovery—Bonjour
3
Discovery—Bonjour
Bonjour enables the WAP device and its services to be discovered by using
multicast DNS (mDNS). Bonjour advertises services to the network and answers
queries for the service types that it supports, simplifying network configuration in
small business environments.
The WAP device advertises these service types:
•
•
Cisco-specific device description (csco-sb)—This service enables clients
to discover Cisco WAP devices and other products deployed in small
business networks.
Management user interfaces—This service identifies the management
interfaces available on the WAP device (HTTP and SNMP).
When a Bonjour-enabled WAP device is attached to a network, any Bonjour client
can discover and get access to the configuration utility without prior configuration.
A system administrator can use an installed Internet Explorer plug-in to discover
the WAP device. The web-based configuration utility shows up as a tab in the
browser.
Bonjour works in both IPv4 and IPv6 networks.
To enable the WAP device to be discovered through Bonjour:
STEP 1 Select Administration > Discovery - Bonjour in the navigation pane.
STEP 2 Select Enable.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
Packet Capture
The wireless packet capture feature enables capturing and storing packets
received and transmitted by the WAP device. The captured packets can then be
analyzed by a network protocol analyzer, for troubleshooting or performance
optimization. There are two methods of packet capture:
•
Local capture method— Captured packets are stored in a file on the WAP
device. The WAP device can transfer the file to a TFTP server. The file is
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
49
Administration
Packet Capture
3
formatted in pcap format and can be examined using tools such as
Wireshark and OmniPeek.
•
Remote capture method—Captured packets are redirected in real time to
an external computer running the Wireshark tool.
The WAP device can capture these types of packets:
•
802.11 packets received and transmitted on radio interfaces. Packets
captured on radio interfaces include the 802.11 header.
•
•
802.3 packets received and transmitted on the Ethernet interface.
802.3 packets received and transmitted on the internal logical interfaces
such as VAPs and WDS interfaces.
Click Administration > Packet Capture to show the Packet Capture page. From
the Packet Capture page you can:
•
•
•
•
Configure packet capture parameters.
Start a local or remote packet capture.
View the current packet capture status.
Download a packet capture file.
Packet Capture Configuration
The Packet Capture Configuration area enables you to configure parameters and
initiate a packet capture.
To configure packet capture settings:
STEP 1 Configure these parameters:
•
Capture Beacons—Enables or disables the capturing of 802.11 beacons
detected or transmitted by the radio.
•
Promiscuous Capture—Enables or disables promiscuous mode when the
capture is active.
In promiscuous mode, the radio receives all traffic on the channel, including
traffic that is not destined to this WAP device. While the radio is operating in
promiscuous mode, it continues serving associated clients. Packets not
destined to the WAP device are not forwarded.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
50
Administration
Packet Capture
3
As soon as the capture is completed, the radio reverts to nonpromiscuous
mode operation.
•
•
Radio Client Filter—Enables or disables the WLAN client filter to capture
only frames that are transmitted to, or received from, a WLAN client with a
specified MAC address.
Client Filter MAC Address—Specifies the MAC address for WLAN client
filtering.
NOTE The MAC filter is active only when a capture is performed on an
802.11 interface.
•
Packet Capture Method—Select one of these options:
-
-
Local File—Captured packets are stored in a file on the WAP device.
Remote—Captured packets are redirected in real time to an external
computer running the Wireshark tool.
STEP 2 Depending on the selected method, refer to the steps in the Local Packet Capture
or Remote Packet Capture section to continue.
NOTE Changes to packet capture configuration parameters take affect after packet
capture is restarted. Modifying the parameters while the packet capture is running
does not affect the current packet capture session. To begin using new parameter
values, an existing packet capture session must be stopped and restarted.
Local Packet Capture
To initiate a local packet capture:
STEP 1 Ensure that Local File is selected for the Packet Capture Method.
STEP 2 Configure these parameters:
•
Capture Interface—Enter a capture interface type for packet capture:
-
-
-
-
radio1—802.11 traffic on the radio interface.
eth0—802.3 traffic on the Ethernet port.
VAP0—VAP0 traffic.
VAP1 to VAP15, if configured—Traffic on the specified VAP.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
51
Administration
Packet Capture
3
-
brtrunk—Linux bridge interface in the WAP device.
•
•
Capture Duration—Enter the time duration in seconds for the capture. The
range is from 10 to 3600. The default is 60.
Max Capture File Size—Enter the maximum allowed size for the capture file
in KB. The range is from 64 to 4096. The default is 1024.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
STEP 4 Click Start Capture.
In Packet File Capture mode, the WAP device stores captured packets in the RAM
file system. Upon activation, the packet capture proceeds until one of these events
occurs:
•
•
•
The capture time reaches the configured duration.
The capture file reaches its maximum size.
The administrator stops the capture.
The Packet Capture Status area of the page shows the status of a packet capture,
if one is active on the WAP device.
•
•
•
Current Capture Status—Whether packet capture is running or stopped.
Packet Capture Time—Elapsed capture time.
Packet Capture File Size—The current capture file size.
Click Refresh to show the latest data from the WAP device.
NOTE To stop a packet file capture, click Stop Capture.
Remote Packet Capture
The Remote Packet Capture feature enables you to specify a remote port as the
destination for packet captures. This feature works in conjunction with the
Wireshark network analyzer tool for Windows. A packet capture server runs on the
WAP device and sends the captured packets through a TCP connection to the
Wireshark tool. Wireshark is an open source tool and is available for free; it can be
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
52
Administration
Packet Capture
3
A Microsoft Windows computer running the Wireshark tool allows you to display,
log, and analyze captured traffic. The remote packet capture facility is a standard
feature of the Wireshark tool for Windows. Linux version does not work with the
WAP device.
When remote capture mode is in use, the WAP device does not store any captured
data locally in its file system.
If a firewall is installed between the Wireshark computer and the WAP device, the
traffic for these ports must be allowed to pass through the firewall. The firewall
must also be configured to allow the Wireshark computer to initiate a TCP
connection to the WAP device.
To initiate a remote capture on a WAP device:
STEP 1 Click Administration > Packet Capture.
STEP 2 Enable Promiscuous Capture.
STEP 3 For the Packet Capture Method, select Remote.
STEP 4 For the Remote Capture Port, use the default port (2002), or if you are using a
port other than the default, enter the desired port number used for connecting
Wireshark to the WAP device. The port range is from 1025 to 65530.
STEP 5 If you want to save the settings for use at another time, click Save. (The selection
of Remote as the Packet Capture Method is not saved, however.)
STEP 6 Click Start Capture.
To initiate the Wireshark network analyzer tool for Microsoft Windows:
STEP 1 On the same computer, initiate the Wireshark tool.
STEP 2 In the menu, select Capture > Options. A popup window appears.
STEP 3 At Interface, select Remote. A popup window appears.
STEP 4 At Host, enter the IP address of the WAP device.
STEP 5 At Port, enter the port number of the WAP. For example, enter 2002 if you used the
default, or enter the port number if you used a port other than the default.
STEP 6 Click OK.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
53
Administration
Packet Capture
3
STEP 7 Select the interface from which you need to capture packets. At the Wireshark
popup window, next to the IP address, there is a pull-down list for you to select the
interfaces. The interface can be one of the following:
Linux bridge interface in the wap device
--rpcap://[192.168.1.220]:2002/brtrunk
Wired LAN interface
-- rpcap://[192.168.1.220]:2002/eth0
VAP0 traffic on radio 1
-- rpcap://[192.168.1.220]:2002/wlan0
802.11 traffic
-- rpcap://[192.168.1.220]:2002/radio1
At WAP321, VAP1 ~ VAP7 traffic
-- rpcap://[ 192.168.1.220]:2002/wlan0vap1 ~ wlan0vap7
At WAP321, VAP1 ~ VAP3 traffic
-- rpcap://[ 192.168.1.220]:2002/wlan0vap1 ~ wlan0vap3
You can trace up to four interfaces on the WAP device at the same time. However,
you must start a separate Wireshark session for each interface. To initiate
additional remote capture sessions, repeat the Wireshark configuration steps; no
configuration needs to be done on the WAP device.
NOTE The system uses four consecutive port numbers, starting with the configured port
for the remote packet capture sessions. Verify that you have four consecutive port
numbers available. We recommend that if you do not use the default port, use a port
number greater than 1024.
When you are capturing traffic on the radio interface, you can disable beacon
capture, but other 802.11 control frames are still sent to Wireshark. You can set up
a display filter to show only:
•
•
•
Data frames in the trace
Traffic on specific Basic Service Set IDs (BSSIDs)
Traffic between two clients
Some examples of useful display filters are:
•
•
•
Exclude beacons and ACK/RTS/CTS frames:
!(wlan.fc.type_subtype == 8 | | wlan.fc.type == 1)
Data frames only:
wlan.fc.type == 2
Traffic on a specific BSSID:
wlan.bssid == 00:02:bc:00:17:d0
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
54
Administration
Packet Capture
3
•
All traffic to and from a specific client:
wlan.addr == 00:00:e8:4e:5f:8e
In remote capture mode, traffic is sent to the computer running Wireshark through
one of the network interfaces. Depending on the location of the Wireshark tool, the
traffic can be sent on an Ethernet interface or one of the radios. To avoid a traffic
flood caused by tracing the packets, the WAP device automatically installs a
capture filter to filter out all packets destined to the Wireshark application. For
example, if the Wireshark IP port is configured to be 58000, then this capture filter
is automatically installed on the WAP device:
not portrange 58000-58004
Due to performance and security issues, the packet capture mode is not saved in
NVRAM on the WAP device; if the WAP device resets, the capture mode is
disabled and then you must reenable it to resume capturing traffic. Packet capture
parameters (other than mode) are saved in NVRAM.
Enabling the packet capture feature can create a security issue: Unauthorized
clients may be able to connect to the WAP device and trace user data. The
performance of the WAP device also is negatively impacted during packet
capture, and this impact continues to a lesser extent even when there is no active
Wireshark session. To minimize the performance impact on the WAP device during
traffic capture, install capture filters to limit which traffic is sent to the Wireshark
tool. When capturing 802.11 traffic, a large portion of the captured frames tends to
be beacons (typically sent every 100 ms by all APs). Although Wireshark supports
a display filter for beacon frames, it does not support a capture filter to prevent the
WAP device from forwarding captured beacon packets to the Wireshark tool. To
reduce the performance impact of capturing the 802.11 beacons, disable the
capture beacons mode.
Packet Capture File Download
You can download a capture file by TFTP to a configured TFTP server, or by
HTTP(S) to a computer. A capture is automatically stopped when the capture file
download command is triggered.
Because the capture file is located in the RAM file system, it disappears if the WAP
device is reset.
To download a packet capture file using TFTP:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
55
Administration
Support Information
3
STEP 1 Select Use TFTP to download the capture file.
STEP 2 Enter the TFTP Server Filename to download if different from the default. By
default, the captured packets are stored in the folder file /tmp/apcapture.pcap on
the WAP device.
STEP 3 Specify a TFTP Server IPv4 Address in the field provided.
STEP 4 Click Download.
To download a packet capture file using HTTP:
STEP 1 Clear Use TFTP to download the captured file.
STEP 2 Click Download. A confirmation window appears.
STEP 3 Click OK. A dialog box displays that enables you to choose a network location to
save the file.
Support Information
The Support Information page enables you to download a text file that contains
detailed configuration information about the AP. The file includes software and
hardware version information, MAC and IP addresses, the administrative and
operational status of features, user-configured settings, traffic statistics, and more.
You can provide the text file to technical support personnel to assist them in
troubleshooting problems.
To show the Support Information page, select Administration > Support
Information in the navigation pane.
Click Download to generate the file based on current system settings. After a
short pause, a window appears to enable you to save the file to your computer.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
56
4
LAN
This chapter describes how to configure the port, network, and clock settings of
the WAP devices.
It includes these topics:
•
•
•
Port Settings
The Port Settings page enables you to view and configure settings for the port
that physically connects the WAP device to a local area network.
To view and configure LAN settings:
STEP 1 Select LAN > Port Settings in the navigation area.
The Operational Status area shows the type of port used for the LAN port and the
Link characteristics, as configured in the Administrative Settings area. If the
settings change through configuration or auto negotiation, you can click Refresh to
show the latest settings.
STEP 2 Enable or disable Auto Negotiation.
•
When enabled, the port negotiates with its link partner to set the fastest link
speed and duplex mode available.
•
When disabled, you can manually configure the port speed and duplex
mode.
STEP 3 If autonegotiation is disabled, select a Port Speed (10/100 Mb/s for the WAP121,
and 10/100/1000 Mb/s for the WAP321) and the duplex mode (Half- or Full-
duplex).
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
57
LAN
VLAN and IPv4 Address Settings
4
STEP 4 Enable or disable Green Ethernet Mode (WAP321 only).
•
Green Ethernet Mode is an auto-power-down mode that reduces chip
power when the signal from a link partner is not present. Green Ethernet
Mode works whether the port has auto-negotiation enabled or disabled.
•
When Green Ethernet Mode is enabled, the WAP device automatically enters
a low-power mode when energy on the line is lost, and it resumes normal
operation when energy is detected.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
VLAN and IPv4 Address Settings
You can use the VLAN and IPv4 Address Settings page to configure settings for
the LAN interface, including static or dynamic IPv4 address assignment.
To configure LAN settings:
STEP 1 Select LAN > VLAN and IPv4 Address in the navigation area.
The page shows Global Settings and IPv4 Settings. The Global Settings area
shows the MAC address of the LAN interface port. This field is read-only.
STEP 2 Configure these Global Settings:
•
Untagged VLAN—Enables or disables VLAN tagging. When enabled (the
default), all traffic is tagged with a VLAN ID.
By default all traffic on the access point uses VLAN 1, the default untagged
VLAN. This means that all traffic is untagged until you disable the untagged
VLAN, change the untagged traffic VLAN ID, or change the VLAN ID for a VAP
or client using RADIUS.
•
Untagged VLAN ID—Specifies a number between 1 and 4094 for the
untagged VLAN ID. The default is 1. Traffic on the VLAN that you specify in
this field is not be tagged with a VLAN ID when forwarded to the network.
VLAN 1 is the both default untagged VLAN and the default management
VLAN. If you want to segregate management traffic from the untagged VLAN
traffic, configure the new VLAN ID at your router, and then use this new VLAN
ID on your WAP device.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
58
LAN
IPv6 Addresses
4
•
Management VLAN ID—The VLAN associated with the IP address you use
to access the WAP device. Provide a number between 1 and 4094 for the
Management VLAN ID. The default is 1.
This VLAN is also the default untagged VLAN. If you already have a
management VLAN configured on your network with a different VLAN ID, you
must change the VLAN ID of the management VLAN on the WAP device.
STEP 3 Configure these IPv4 settings:
•
Connection Type—By default, the DHCP client on the Cisco WAP121 and
WAP321 automatically broadcasts requests for network information. If you
want to use a static IP address, you must disable the DHCP client and
manually configure the IP address and other network information.
Select one of these values from the list:
-
DHCP—The WAP device acquires its IP address from a DHCP server on
the LAN.
-
Static IP—You manually configure the IPv4 address. The IPv4 address
should be in a form similar to xxx.xxx.xxx.xxx (192.0.2.10).
•
•
Static IP Address, Subnet Mask, and Default Gateway—If you elected to
assign a static IP address, enter the IP information.
Domain Name Servers—Select an option from the list:
-
Dynamic—The WAP device acquires DNS server addresses from a
DHCP server on the LAN.
-
Manual—You manually configure one or more DNS server addresses.
Enter up to two IP addresses in the text boxes.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
NOTE After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
IPv6 Addresses
You can use the IPv6 Addresses page to configure the WAP device to use IPv6
addresses.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
59
LAN
IPv6 Addresses
4
To configure IPv6 address settings:
STEP 1 Select LAN > IPv6 Addresses in the navigation area.
STEP 2 Configure the following settings:
•
IPv6 Connection Type—Choose how the WAP device obtains an IPv6
address:
-
-
DHCPv6—The IPv6 address is assigned by a DHCPv6 server.
Static IPv6—You manually configure the IPv6 address. The IPv6 address
should be in a form similar to xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx
(2001:DB8::CAD5:7D91).
•
•
IPv6 Administration Mode—Enables IPv6 management access.
IPv6 Auto Configuration Administration Mode—Enables IPv6 automatic
address configuration on the WAP device.
When enabled, the WAP device learns its IPv6 addresses and gateway by
processing the Router Advertisements received on the LAN port. The WAP
device can have multiple autoconfigured IPv6 addresses.
•
Static IPv6 Address—The static IPv6 address. The WAP device can have a
static IPv6 address even if addresses have already been configured
automatically.
•
•
Static IPv6 Address Prefix Length—The prefix length of the static address,
which is an integer in the range of 0 to 128. The default is 0.
Static IPv6 Address Status—One of the following values appears:
-
Operational—The IP address has been verified as unique on the LAN
and is usable on the interface.
-
Tentative—The WAP device initiates a duplicate address detection
(DAD) process automatically when a static IP address is assigned. An
IPv6 address is in the tentative state while it is being verified as unique on
the network. While in this state, the IPv6 address cannot be used to
transmit or receive ordinary traffic.
-
Blank (no value)—No IP address is assigned or the assigned address is
not operational.
•
IPv6 Autoconfigured Global Addresses—If the WAP device has been
assigned one or more IPv6 addresses automatically, the addresses are
listed.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
60
LAN
IPv6 Addresses
4
•
IPv6 Link Local Address—The IPv6 address used by the local physical link.
The link local address is not configurable and is assigned by using the IPv6
Neighbor Discovery process.
•
•
Default IPv6 Gateway—The statically configured default IPv6 gateway.
IPv6 DNS Nameservers—Select one of the following values:
-
Dynamic—The DNS name servers are learned dynamically through
DHCPv6.
-
Manual—You specify up to two IPv6 DNS name servers in the fields
provided.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
NOTE After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
61
5
Wireless
This chapter describes how to configure properties of the wireless radio
operation.
It includes these topics:
•
•
•
•
•
•
•
•
•
•
•
•
Radio
Radio settings directly control the behavior of the radio in the WAP device and its
interaction with the physical medium; that is, how and what type of signal the WAP
device emits.
To configure radio settings:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
62
Wireless
Radio
5
STEP 1 Select Wireless > Radio in the navigation pane.
STEP 2 In the Global Settings area, configure the TSPEC Violation Interval, which is the
time interval in seconds for the WAP device to report associated clients that do
not adhere to mandatory admission control procedures. The reporting occurs
through the system log and SNMP traps. Enter a time from 0 to 900 seconds. The
default is 300 seconds.
STEP 3 In the Basic Settings area, configure these settings:
NOTE Local regulations may prohibit the use of certain radio modes. Not all
modes are available in all countries.
•
•
Radio—Turns on or off the radio interface. By default, the radio is off.
MAC Address—The Media Access Control (MAC) address for the interface.
The MAC address is assigned by the manufacturer and cannot be changed.
•
Mode—The IEEE 802.11 standard and frequency the radio uses. Select one
of the available modes:
-
-
-
802.11a—Only 802.11a clients can connect to the WAP device.
802.11b/g—802.11b and 802.11g clients can connect to the WAP device.
802.11a/n—802.11a clients and 802.11n clients operating in the 5-GHz
frequency can connect to the WAP device.
-
-
-
802.11b/g/n (default)—802.11b, 802.11g, and 802.11n clients operating in
the 2.4-GHz frequency can connect to the WAP device.
5 GHz 802.11n—Only 802.11n clients operating in the 5-GHz frequency
can connect to the WAP device.
2.4 GHz 802.11n—Only 802.11n clients operating in the 2.4-GHz
frequency can connect to the WAP device.
•
Channel Bandwidth—The 802.11n specification allows a coexisting 20/
40 MHz channel in addition to the legacy 20 MHz channel available with
other modes. The 20/40 MHz channel enables higher data rates but leaves
fewer channels available for use by other 2.4 GHz and 5 GHz devices.
By default, when the radio mode includes 802.11n, the channel bandwidth is
set to 20/40 MHz to enable both channel widths. Set the field to 20 MHz to
restrict the use of the channel bandwidth to a 20 MHz channel.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
63
Wireless
Radio
5
•
Primary Channel (802.11n modes with 20/40 MHz bandwidth only)—A
40 MHz channel can be considered to consist of two 20 MHz channels that
are contiguous in the frequency domain. These two 20 MHz channels are
often referred to as the Primary and Secondary channels. The Primary
Channel is used for 802.11n clients that support only a 20 MHz channel
bandwidth and for legacy clients.
Select one of these options:
-
Upper—Sets the Primary Channel as the upper 20 MHz channel in the
40 MHz band.
-
Lower—Sets the Primary Channel as the lower 20 MHz channel in the
40 MHz band. Lower is the default selection.
•
Channel—The portion of the radio spectrum the radio uses for transmitting
and receiving.
The range of available channels is determined by the mode of the radio
interface and the country code setting. If you select Auto for the channel
setting, the WAP device scans available channels and selects a channel
where the least amount of traffic is detected.
Each mode offers a number of channels, depending on how the spectrum is
licensed by national and transnational authorities such as the Federal
Communications Commission (FCC) or the International Telecommunication
Union (ITU-R).
STEP 4 In the Advanced Settings area, configure these settings:
•
Short Guard Interval Supported—This field is available only if the selected
radio mode includes 802.11n.
The guard interval is the dead time, in nanoseconds, between OFDM
symbols. The guard interval prevents Inter-Symbol and Inter-Carrier
Interference (ISI, ICI). The 802.11n mode allows for a reduction in this guard
interval from the a and g definition of 800 nanoseconds to 400 nanoseconds.
Reducing the guard interval can yield a 10 percent improvement in data
throughput.
The client with which the WAP device is communicating must also support
the short guard interval.
Select one of these options:
-
Yes—The WAP device transmits data using a 400-nanosecond guard
Interval when communicating with clients that also support the short
guard interval. Yes is the default selection.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
64
Wireless
Radio
5
-
No—The WAP device transmits data using an 800-nanosecond guard
interval.
•
Protection—The protection feature contains rules to guarantee that 802.11
transmissions do not cause interference with legacy stations or applications.
By default, protection is enabled (Auto). With protection enabled, protection
is invoked if legacy devices are within range of the WAP device.
You can disable protection (Off); however, legacy clients or WAP devices
within range can be affected by 802.11n transmissions. Protection is also
available when the mode is 802.11b/g. When protection is enabled in this
mode, it protects 802.11b clients and WAP devices from 802.11g
transmissions.
NOTE This setting does not affect the ability of the client to associate with
the WAP device.
•
Beacon Interval—The interval between the transmission of beacon frames.
The WAP device transmits these at regular intervals to announce the
existence of the wireless network. The default behavior is to send a beacon
frame once every 100 milliseconds (or 10 per second).
Enter an integer from 20 to 2000 milliseconds. The default is 100
milliseconds.
•
DTIM Period—The Delivery Traffic Information Map (DTIM) period. Enter an
integer from 1 to 255 beacons. The default is 2 beacons.
The DTIM message is an element included in some Beacon frames. It
indicates which client stations, currently sleeping in low-power mode, have
data buffered on the WAP device awaiting pickup.
The DTIM period that you specify indicates how often the clients served by
this WAP device should check for buffered data still on the WAP device
awaiting pickup.
The measurement is in beacons. For example, if you set this field to 1, clients
check for buffered data on the WAP device at every beacon. If you set this
field to 10, clients check on every 10th beacon.
•
Fragmentation Threshold—The frame size threshold in bytes. The valid
integer must be even and in the range of 256 to 2346. The default is 2346.
The fragmentation threshold is a way of limiting the size of packets (frames)
transmitted over the network. If a packet exceeds the fragmentation
threshold you set, the fragmentation function is activated and the packet is
sent as multiple 802.11 frames.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
65
Wireless
Radio
5
If the packet being transmitted is equal to or less than the threshold,
fragmentation is not used. Setting the threshold to the largest value (2,346
bytes, which is the default) effectively disables fragmentation.
Fragmentation involves more overhead both because of the extra work of
dividing up and reassembling of frames it requires, and because it increases
message traffic on the network. However, fragmentation can help improve
network performance and reliability if properly configured.
Sending smaller frames (by using lower fragmentation threshold) might help
with some interference problems; for example, with microwave ovens.
By default, fragmentation is off. We recommend not using fragmentation
unless you suspect radio interference. The additional headers applied to
each fragment increase the overhead on the network and can greatly reduce
throughput.
•
RTS Threshold—The Request to Send (RTS) Threshold value. The valid
integer range must be from 0 to 2347. The default is 2347 octets.
The RTS threshold indicates the number of octets in an MPDU, below which
an RTS/CTS handshake is not performed.
Changing the RTS threshold can help control traffic flow through the WAP
device, especially one with a lot of clients. If you specify a low threshold
value, RTS packets are sent more frequently, which consumes more
bandwidth and reduces the throughput of the packet. However, sending
more RTS packets can help the network recover from interference or
collisions that might occur on a busy network, or on a network experiencing
electromagnetic interference.
•
•
Maximum Associated Clients—The maximum number of stations allowed
to access this WAP device at any one time. You can enter an integer between
0 and 200. The default is 200 stations.
Transmit Power—A percentage value for the transmit power level for this
WAP device.
The default value of 100 percent can be more cost-efficient than a lower
percentage because it gives the WAP device a maximum broadcast range
and reduces the number of access points needed.
To increase the capacity of the network, place WAP devices closer together
and reduce the value of the transmit power. This helps reduce overlap and
interference among access points. A lower transmit power setting can also
keep your network more secure because weaker wireless signals are less
likely to propagate outside of the physical location of your network.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
66
Wireless
Radio
5
Some channel ranges and country code combinations have relatively low
maximum transmit power. When attempting to set the transmit power to the
lower ranges (for example, 25% or 12%), the expected drop in power may
not occur, because certain power amplifiers have minimum transmit power
requirements.
•
Fixed Multicast Rate—The transmission rate in Mbps for broadcast and
multicast packets. This setting can be useful in an environment where
wireless multicast video streaming occurs, provided the wireless clients are
capable of handling the configured rate.
When Auto is selected, the WAP device chooses the best rate for the
associated clients. The range of valid values is determined by the configured
radio mode.
•
Legacy Rate Sets—Rates are expressed in megabits per second.
Supported Rate Sets indicate rates that the WAP device supports. You can
check multiple rates (check a box to select or deselect a rate). The WAP
device automatically chooses the most efficient rate based on factors such
as error rates and the distance of client stations from the WAP device.
Basic Rate Sets indicate rates that the WAP device advertises to the network
for the purposes of setting up communication with other access points and
client stations on the network. It is generally more efficient to have a WAP
device broadcast a subset of its supported rate sets.
•
MCS (Data Rate) Settings—The Modulation and Coding Scheme (MCS)
index values that the WAP device advertises. MCS can enhance throughput
for 802.11n wireless clients.
Check the box below the MCS index number to enable it or uncheck it to
disable the index. You cannot disable all indexes at the same time.
The WAP device supports MCS indexes 0 to 15. MSC index 15 allows for a
maximum transmission rate of 300 Mbps. If no MCS index is selected, the
radio operates at MCS index 0, which allows for a maximum transmission
rate of 15 Mbps.
The MCS settings can be configured only if the radio mode includes 802.11n
support.
•
Broadcast/Multicast Rate Limiting—Multicast and broadcast rate limiting
can improve overall network performance by limiting the number of packets
transmitted across the network.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
67
Wireless
Radio
5
By default, the Multicast/Broadcast Rate Limiting option is disabled. Until you
enable Multicast/Broadcast Rate Limiting, these fields are disabled:
-
Rate Limit—The rate limit for multicast and broadcast traffic. The limit
should be greater than 1, but less than 50 packets per second. Any traffic
that falls below this rate limit will always conform and be transmitted to
the appropriate destination. The default and maximum rate limit setting is
50 packets per second.
-
Rate Limit Burst—An amount of traffic, measured in bytes, which is
allowed to pass as a temporary burst even if it is above the defined
maximum rate. The default and maximum rate limit burst setting is 75
packets per second.
•
TSPEC Mode—Regulates the overall TSPEC mode on the WAP device. By
default, TSPEC mode is off. The options are:
-
On—The WAP device handles TSPEC requests according to the TSPEC
settings you configure on the Radio page. Use this setting if the WAP
device handles traffic from QoS-capable devices, such as a Wi-Fi
CERTIFIED phone.
-
Off—The WAP device ignores TSPEC requests from client stations. Use
this setting if you do not want to use TSPEC to give QoS-capable devices
priority for time-sensitive traffic.
•
TSPEC Voice ACM Mode—Regulates mandatory admission control (ACM)
for the voice access category. By default, TSPEC Voice ACM mode is off.
The options are:
-
On—A station is required to send a TSPEC request for bandwidth to the
WAP device before sending or receiving a voice traffic stream. The WAP
device responds with the result of the request, which includes the
allotted medium time if the TSPEC was admitted.
-
Off—A station can send and receive voice priority traffic without
requiring an admitted TSPEC; the WAP device ignores voice TSPEC
requests from client stations.
•
•
TSPEC Voice ACM Limit—The upper limit on the amount of traffic the WAP
device attempts to transmit on the wireless medium using a voice AC to gain
access. The default limit is 20 percent of total traffic.
TSPEC Video ACM Mode —Regulates mandatory admission control for the
video access category. By default, TSPEC Video ACM mode is off. The
options are:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
68
Wireless
Rogue AP Detection
5
-
-
On — A station is required to send a TSPEC request for bandwidth to the
WAP device before sending or receiving a video traffic stream. The WAP
device responds with the result of the request, which includes the
allotted medium time if the TSPEC was admitted.
Off — A station can send and receive video priority traffic without
requiring an admitted TSPEC; the WAP device ignores video TSPEC
requests from client stations.
•
•
•
•
TSPEC Video ACM Limit—The upper limit on the amount of traffic that the
WAP device attempts to transmit on the wireless medium using a video AC
to gain access. The default limit is 15 percent of total traffic.
TSPEC AP Inactivity Timeout—The amount of time for a WAP device to
detect a downlink traffic specification as idle before deleting it. The valid
integer range is from 0 to 120 seconds and the default is 30 seconds.
TSPEC Station Inactivity Timeout—The amount of time for a WAP device
to detect an uplink traffic specification as idle before deleting it. The valid
integer range is from 0 to 120 seconds and the default is 30 seconds.
TSPEC Legacy WMM Queue Map Mode—Enables or disables the
intermixing of legacy traffic on queues operating as ACM. By default, this
mode is off.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
!
CAUTION After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
Rogue AP Detection
A Rogue AP is an access point that has been installed on a secure network without
explicit authorization from a system administrator. Rogue access points pose a
security threat because anyone with access to the premises can ignorantly or
maliciously install an inexpensive wireless WAP device that can potentially allow
unauthorized parties to access the network.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
69
Wireless
Rogue AP Detection
5
The WAP device performs an RF scan on all channels to detect all APs in the
vicinity of the network. If rogue APs are detected, they are shown on the Rogue AP
Detection page. If an AP listed as a rogue is legitimate, you can add it to the Known
AP List.
NOTE The Detected Rogue AP List and Trusted AP List provide information that you can
use to take further action. The AP does not have any control over rogue APs on the
lists and cannot apply any security policies to APs detected through the RF scan.
When AP detection is enabled, the radio periodically switches from its operating
channel to scan other channels within the same band.
Viewing the Rogue AP List
Rogue AP detection can be enabled and disabled. To enable the radio to collect
information about rogue APs, click Enable next to AP Detection and then click
Save.
Information about detected and trusted rogue access points appears. You can
click Refresh to refresh the screen and show the most current information:
•
Action—If the AP is in the Detected Rogue AP List, you can click Trust to
move the AP to the Trusted AP List.
If the AP is in the Trusted AP list, you can click Untrust to move the AP to the
Detected Rogue AP List.
NOTE The Detected Rogue AP List and Trusted AP List provide information.
The WAP device does not have any control over the APs on the list and
cannot apply any security policies to APs detected through the RF scan.
•
•
MAC Address—The MAC address of the rogue AP.
Beacon Interval—The beacon interval used by the rogue AP.
Beacon frames are transmitted by an AP at regular intervals to announce
the existence of the wireless network. The default behavior is to send a
beacon frame once every 100 milliseconds (or 10 per second).
Type—The type of device:
•
-
AP indicates the rogue device is an AP that supports the IEEE 802.11
Wireless Networking Framework in Infrastructure Mode.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
70
Wireless
Rogue AP Detection
5
-
Ad hoc indicates a rogue station running in Ad hoc mode. Stations set to
Ad hoc mode communicate with each other directly, without the use of a
traditional AP. Ad hoc mode is an IEEE 802.11 Wireless Networking
Framework also referred to as peer-to-peer mode or an Independent
Basic Service Set (IBSS).
•
•
SSID—The Service Set Identifier (SSID) for the WAP device.
The SSID is an alphanumeric string of up to 32 characters that uniquely
identifies a wireless local area network. It is also referred to as the Network
Name.
Privacy—Indicates whether there is any security on the rogue device:
-
Off indicates that the Security mode on the rogue device is set to None
(no security).
-
On indicates that the rogue device has some security in place.
WPA—Whether WPA security is on or off for the rogue AP.
•
•
Band—The IEEE 802.11 mode being used on the rogue AP. (For example,
IEEE 802.11a, IEEE 802.11b, IEEE 802.11g.)
The number shown indicates the mode:
-
2.4 indicates IEEE 802.11b, 802.11g, or 802.11n mode (or a combination
of the modes).
-
5 indicates IEEE 802.11a or 802.11n mode (or both modes).
•
Channel—The channel on which the rogue AP is currently broadcasting.
The channel defines the portion of the radio spectrum that the radio uses
for transmitting and receiving.
•
•
Rate—The rate in megabits per second at which the rogue AP is currently
transmitting.
The current rate is always one of the rates shown in Supported Rates.
Signal—The strength of the radio signal emitting from the rogue AP. If you
hover the mouse pointer over the bars, a number representing the strength
in decibels (dB) appears.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
71
Wireless
Rogue AP Detection
5
•
•
•
Beacons—The total number of beacons received from the rogue AP since it
was first discovered.
Last Beacon—The date and time of the last beacon received from the
rogue AP.
Rates—Supported and basic (advertised) rate sets for the rogue AP. Rates
are shown in megabits per second (Mbps).
All Supported Rates are listed, with Basic Rates shown in bold. Rate sets
Creating and Saving a Trusted AP List
To create a Trusted AP List and save it to a file:
STEP 1 In the Detected Rogue AP List, click Trust for APs that are known to you. The
Trusted APs move to the Trusted AP List.
STEP 2 In the Download/Backup Trusted AP List area, select Backup (AP to PC).
STEP 3 Click Save.
The list contains the MAC addresses of all APs that have been added to the
Known AP List. By default, the filename is Rogue2.cfg. You can use a text editor or
web browser to open the file and view its contents.
Importing a Trusted AP List
You can import a list of known APs from a saved list. The list might be acquired
from another AP or created from a text file. If the MAC address of an AP appears in
the Trusted AP List, it is not detected as a rogue.
To import an AP list from a file, use these steps:
STEP 1 In the Download/Backup Trusted AP List area, select Download (PC to AP).
STEP 2 Click Browse and choose the file to import.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
72
Wireless
Networks
5
The file that you import must be a plain-text file with a .txt or .cfg extension. Entries
in the file are MAC addresses in hexadecimal format with each octet separated by
colons, for example 00:11:22:33:44:55. You must separate entries with a single
space. For the AP to accept the file, it must contain only MAC addresses.
STEP 3 Choose whether to replace the existing Trusted AP List or add the entries in the
imported file to the Trusted AP List.
a. Select Replace to import the list and replace the contents of the Known AP
List.
b. Select Merge to import the list and add the APs in the imported file to the APs
currently shown in the Known AP List.
STEP 4 Click Save.
When the import is complete, the screen refreshes and the MAC addresses of the
APs in the imported file appear in the Known AP List.
Networks
Virtual Access Points (VAPs) segment the wireless LAN into multiple broadcast
domains that are the wireless equivalent of Ethernet VLANs. VAPs simulate
multiple access points in one physical WAP device. Up to four VAPs are supported
on the WAP121 and up to eight VAPs are supported on the WAP321.
Each VAP can be independently enabled or disabled, with the exception of VAP0.
VAP0 is the physical radio interface and remains enabled as long as the radio is
enabled. To disable operation of VAP0, the radio itself must be disabled.
Each VAP is identified by a user-configured Service Set Identifier (SSID). Multiple
VAPs cannot have the same SSID name. SSID broadcasts can be enabled or
disabled independently on each VAP. SSID broadcast is enabled by default.
SSID Naming Conventions
The default SSID for VAP0 is ciscosb. Every additional VAP created has a blank
SSID name. The SSIDs for all VAPs can be configured to other values.
The SSID can be any alphanumeric, case-sensitive entry from 2 to 32 characters.
The printable characters plus the space (ASCII 0x20) are allowed, but these six
characters are not:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
73
Wireless
Networks
5
?, ", $, [, \, ], and +.
The allowable characters are:
ASCII 0x20, 0x21, 0x23, 0x25 through 0x2A, 0x2C through 0x3E, 0x40
through 0x5A, 0x5E through 0x7E.
In addition, these three characters cannot be the first character:
!, #, and ; (ASCII 0x21, 0x23, and 0x3B, respectively).
Trailing and leading spaces (ASCII 0x20) are not permitted.
NOTE This means that spaces are allowed within the SSID, but not as the first or last
character, and the period "." (ASCII 0x2E) is also allowed.
VLAN IDs
Each VAP is associated with a VLAN, which is identified by a VLAN ID (VID). A VID
can be any value from 1 to 4094, inclusive. The WAP121 supports five active
VLANs (four for WLAN plus one management VLAN). The WAP321 supports nine
active VLANs (eight for WLAN plus one management VLAN).
By default, the VID assigned to the configuration utility for the WAP device is 1,
which is also the default untagged VID. If the management VID is the same as the
VID assigned to a VAP, then the WLAN clients associated with this specific VAP
can administer the WAP device. If needed, an access control list (ACL) can be
created to disable administration from WLAN clients.
Configuring VAPs
To configure VAPs:
STEP 1 Select Wireless > Networks in the navigation pane.
STEP 2 Select the Enabled check box for the VAP you want to configure.
—Or—
If VAP0 is the only VAP configured on the system, and you want to add a VAP, click
Add. Then, select the VAP and click Edit.
STEP 3 Configure the parameters:
•
VLAN ID—The VID of the VLAN to associate with the VAP.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
74
Wireless
Networks
5
!
CAUTION Be sure to enter a VLAN ID that is properly configured on the network. Network
problems can result if the VAP associates wireless clients with an improperly
configured VLAN.
When a wireless client connects to the WAP device by using this VAP, the WAP
device tags all traffic from the wireless client with the VLAN ID you enter in this field,
unless you enter the port VLAN ID or use a RADIUS server to assign a wireless
client to a VLAN. The range for the VLAN ID is from 1 to 4094.
NOTE If you change the VLAN ID to a different ID than the current
management VLAN ID, WLAN clients associated with this specific VAP
cannot administer the device. Verify the configuration of the untagged and
management VLAN IDs on the LAN page. For more information, see VLAN
•
SSID Name—A name for the wireless network. The SSID is an alphanumeric
string of up to 32 characters. Choose a unique SSID for each VAP.
NOTE If you are connected as a wireless client to the same WAP device that
you are administering, resetting the SSID will cause you to lose connectivity
to the WAP device. You need to reconnect to the new SSID after you save
this new setting.
•
Broadcast SSID—Enables and disables the broadcast of the SSID.
Specify whether to allow the WAP device to broadcast the SSID in its
beacon frames. The Broadcast SSID parameter is enabled by default. When
the VAP does not broadcast its SSID, the network name is not shown in the
list of available networks on a client station. Instead, you must enter the exact
network name manually into the wireless connection utility on the client so
that it can connect.
Disabling the broadcast SSID is sufficient to prevent clients from
accidentally connecting to your network, but it does not prevent even the
simplest of attempts by a hacker to connect or monitor unencrypted traffic.
Suppressing the SSID broadcast offers a very minimal level of protection on
an otherwise exposed network (such as a guest network) where the priority
is to make it easy for clients to get a connection and where no sensitive
information is available.
•
Security—The type of authentication required for access to the VAP:
-
-
None
Static WEP
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
75
Wireless
Networks
5
-
-
-
Dynamic WEP
WPA Personal
WPA Enterprise
If you select a security mode other than None, additional fields appear.
NOTE We recommend using WPA Personal or WPA Enterprise as the
authentication type as it provides stronger security protection. Use Static
WEP or Dynamic WEP only for legacy wireless computers or devices that do
not support WPA Personal/Enterprise. If you need to set security as Static
WEP or Dynamic WEP, configure Radio as 802.11a or 802.11b/g mode (see
security mode.
•
MAC Filtering—Specifies whether the stations that can access this VAP are
restricted to a configured global list of MAC addresses. You can select one
of these types of MAC filtering:
-
-
Disabled—Do not use MAC filtering.
Filtering page.
-
RADIUS—Use the MAC Authentication list on an external RADIUS server.
•
Channel Isolation—Enables and disables station isolation.
-
When disabled, wireless clients can communicate with one another
normally by sending traffic through the WAP device.
-
When enabled, the WAP device blocks communication between
wireless clients on the same VAP. The WAP device still allows data traffic
between its wireless clients and wired devices on the network, across a
WDS link, and with other wireless clients associated with a different VAP,
but not among wireless clients.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
!
CAUTION After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
76
Wireless
Networks
5
NOTE To delete a VAP, select the VAP and click Delete. To save your deletion permanently,
click Save when complete.
Configuring Security Settings
These sections describe the security settings that you configure, depending on
your selection in the Security list on the Networks page.
None (Plain-text)
If you select None as your security mode, no additional security settings are
configurable on the WAP device. This mode means that any data transferred to
and from the WAP device is not encrypted. This security mode can be useful
during initial network configuration or for problem solving, but it is not
recommended for regular use on the internal network because it is not secure.
Static WEP
Wired Equivalent Privacy (WEP) is a data encryption protocol for 802.11 wireless
networks. All wireless stations and access points on the network are configured
with a static 64-bit (40-bit secret key + 24-bit initialization vector (IV)) or 128-bit
(104-bit secret key + 24-bit IV) Shared Key for data encryption.
Static WEP is not the most secure mode available, but it offers more protection
than setting the security mode to None (Plain-text), as it does prevent an outsider
from easily sniffing out unencrypted wireless traffic.
WEP encrypts data moving across the wireless network based on a static key.
(The encryption algorithm is a stream cipher called RC4.)
These parameters configure Static WEP:
•
Transfer Key Index—A key index list. Key indexes 1 through 4 are available.
The default is1.
The Transfer Key Index indicates which WEP key the WAP device uses to
encrypt the data it transmits.
•
•
Key Length—The length of the key. Select one:
-
-
64 bits
128 bits
Key Type—The key type. Select one:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
77
Wireless
Networks
5
-
-
ASCII
Hex
•
WEP Keys—You can specify up to four WEP keys. In each text box, enter a
string of characters for each key. The keys you enter depend on the key
type selected:
-
ASCII—Includes uppercase and lowercase alphabetic letters, the
numeric digits, and special symbols such as @ and #.
-
Hex—Includes digits 0 to 9 and the letters A to F.
Use the same number of characters for each key as specified in the
Characters Required field. These are the RC4 WEP keys shared with the
stations using the WAP device.
Each client station must be configured to use one of these same WEP keys
in the same slot as specified on the WAP device.
•
•
Characters Required—The number of characters you enter into the WEP
Key fields is determined by the key length and key type you select. For
example, if you use 128-bit ASCII keys, you must enter 26 characters in the
WEP key. The number of characters required updates automatically based
on how you set the key length and key type.
802.1X Authentication—The authentication algorithm defines the method
used to determine whether a client station is allowed to associate with WAP
device when static WEP is the security mode.
Specify the authentication algorithm you want to use by choosing one of
these options:
-
Open System authentication allows any client station to associate with
the WAP device whether that client station has the correct WEP key or
not. This algorithm is also used in plaintext, IEEE 802.1X, and WPA
modes. When the authentication algorithm is set to Open System, any
client can associate with the WAP device.
NOTE Just because a client station is allowed to associate does not
ensure it can exchange traffic with an WAP device. A station must have
the correct WEP key to be able to successfully access and decrypt data
from the WAP device, and to transmit readable data to the WAP device.
-
Shared Key authentication requires the client station to have the correct
WEP key in order to associate with the WAP device. When the
authentication algorithm is set to Shared Key, a station with an incorrect
WEP key cannot associate with the WAP device.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
78
Wireless
Networks
5
-
Both Open System and Shared Key. When you select both
authentication algorithms, client stations configured to use WEP in
shared key mode must have a valid WEP key in order to associate with
the WAP device. Also, client stations configured to use WEP as an open
system (shared key mode not enabled) can associate with the WAP
device even if they do not have the correct WEP key.
Static WEP Rules
If you use Static WEP, these rules apply:
•
All client stations must have the Wireless LAN (WLAN) security set to WEP,
and all clients must have one of the WEP keys specified on the WAP device
in order to decode AP-to-station data transmissions.
•
•
The WAP device must have all keys used by clients for station-to-AP
transmit so that it can decode the station transmissions.
The same key must occupy the same slot on all nodes (AP and clients). For
example, if the WAP device defines abc123 key as WEP key 3, then the
client stations must define that same string as WEP key 3.
•
•
Client stations can use different keys to transmit data to the access point.
(Or they can all use the same key, but using the same key is less secure
because it means one station can decrypt the data being sent by another.)
On some wireless client software, you can configure multiple WEP keys and
define a client station transfer key index, and then set the stations to encrypt
the data they transmit using different keys. This ensures that neighboring
access points cannot decode other access point transmissions.
•
You cannot mix 64-bit and 128-bit WEP keys between the access point and
its client stations.
Dynamic WEP
Dynamic WEP refers to the combination of 802.1x technology and the Extensible
Authentication Protocol (EAP). With Dynamic WEP security, WEP keys are changed
dynamically.
EAP messages are sent over an IEEE 802.11 wireless network using a protocol
called EAP Encapsulation Over LANs (EAPOL). IEEE 802.1X provides dynamically
generated keys that are periodically refreshed. An RC4 stream cipher is used to
encrypt the frame body and cyclic redundancy checking (CRC) of each 802.11
frame.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
79
Wireless
Networks
5
This mode requires the use of an external RADIUS server to authenticate users.
The WAP device requires a RADIUS server that supports EAP, such as the
Microsoft Internet Authentication Server. To work with Microsoft Windows clients,
the authentication server must support Protected EAP (PEAP) and MSCHAP V2.
You can use any of a variety of authentication methods that the IEEE 802.1X mode
supports, including certificates, Kerberos, and public key authentication. You must
configure the client stations to use the same authentication method the WAP
device uses.
These parameters configure Dynamic WEP:
•
Use Global RADIUS Server Settings—By default, each VAP uses the
global RADIUS settings that you define for the WAP device (see RADIUS
RADIUS servers.
To use the global RADIUS server settings, ensure that the check box is
selected.
To use a separate RADIUS server for the VAP, uncheck the check box and
enter the RADIUS server IP address and key in these fields:
•
•
Server IP Address Type—The IP version that the RADIUS server uses.
You can toggle between the address types to configure IPv4 and IPv6
global RADIUS address settings, but the WAP device contacts only the
RADIUS server or servers for the address type you select in this field.
Server IP Address 1 or Server IPv6 Address 1—The address for the
primary RADIUS server for this VAP.
When the first wireless client tries to authenticate with the WAP device, the
WAP device sends an authentication request to the primary server. If the
primary server responds to the authentication request, the WAP device
continues to use this RADIUS server as the primary server, and
authentication requests are sent to the address you specify.
The IPv4 address should be in a form similar to xxx.xxx.xxx.xxx (192.0.2.10).
The IPv6 address should be in a form similar to
xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx (2001:DB8::CAD5:7D91).
•
Server IP Address 2 to 4 or Server IPv6 Address 2 to 4—Up to three IPv4
or IPv6 backup RADIUS server addresses.
If authentication fails with the primary server, each configured backup
server is tried in sequence.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
80
Wireless
Networks
5
•
Key—The shared secret key that the WAP device uses to authenticate to
the primary RADIUS server.
You can use up to 63 standard alphanumeric and special characters. The
key is case sensitive and must match the key configured on the RADIUS
server. The text you enter is shown as asterisks.
•
•
Key 2 to Key 4—The RADIUS key associated with the configured backup
RADIUS servers. The server at Server IP (IPv6) Address 2 uses Key 2, the
server at Server IP (IPv6) Address 3 uses Key 3, and so on.
Enable RADIUS Accounting—Enables tracking and measuring of the
resources a particular user has consumed, such as system time, amount of
data transmitted and received, and so on.
If you enable RADIUS accounting, it is enabled for the primary RADIUS
server and all backup servers.
•
•
Active Server—Enables administratively selecting the active RADIUS
server, rather than having the WAP device attempt to contact each
configured server in sequence and choose the first server that is up.
Broadcast Key Refresh Rate—The interval at which the broadcast (group)
key is refreshed for clients associated with this VAP.
The default is 300. The valid range is from 0 to 86400 seconds. A value of 0
indicates that the broadcast key is not refreshed.
•
Session Key Refresh Rate—The interval at which the WAP device
refreshes session (unicast) keys for each client associated with the VAP.
The valid range is from 0 to 86400 seconds. A value of 0 indicates that the
broadcast key is not refreshed.
WPA Personal
WPA Personal is a Wi-Fi Alliance IEEE 802.11i standard, which includes AES-CCMP
and TKIP encryption. The Personal version of WPA uses a pre-shared key (PSK)
instead of using IEEE 802.1X and EAP as is used in the Enterprise WPA security
mode. The PSK is used for an initial check of credentials only. WPA Personal is also
referred to as WPA-PSK.
This security mode is backwards-compatible for wireless clients that support the
original WPA.
These parameters configure WPA Personal:
•
WPA Versions—The types of client stations you want to support:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
81
Wireless
Networks
5
-
-
WPA—The network has client stations that support the original WPA
and none that support the newer WPA2.
WPA2—All client stations on the network support WPA2. This protocol
version provides the best security per the IEEE 802.11i standard.
If the network has a mix of clients, some of which support WPA2 and others
which support only the original WPA, select both of the check boxes. This
lets both WPA and WPA2 client stations associate and authenticate, but
uses the more robust WPA2 for clients who support it. This WPA
configuration allows more interoperability in place of some security.
•
Cipher Suites—The cipher suite you want to use:
-
-
TKIP
CCMP (AES)
You can select either or both. Both TKIP and AES clients can associate with
the WAP device. WPA clients must have one of these keys to be able to
associate with the WAP device:
-
-
A valid TKIP key
A valid AES-CCMP key
Clients not configured to use WPA Personal are not able to associate with
the WAP device.
•
•
Key—The shared secret key for WPA Personal security. Enter a string of at
least 8 characters to a maximum of 63 characters. Acceptable characters
include uppercase and lowercase alphabetic letters, the numeric digits, and
special symbols such as @ and #.
Key Strength Meter—The WAP device checks the key against complexity
criteria such as how many different types of characters (uppercase and
lowercase alphabetic letters, numbers, and special characters) are used
and how long the string is. If the WPA-PSK complexity check feature is
enabled, the key is not accepted unless it meets the minimum criteria. See
•
Broadcast Key Refresh Rate—The interval at which the broadcast (group)
key is refreshed for clients associated with this VAP. The default is 300
seconds and the valid range is from 0 to 86400 seconds. A value of 0
indicates that the broadcast key is not refreshed.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
82
Wireless
Networks
5
WPA Enterprise
WPA Enterprise with RADIUS is an implementation of the Wi-Fi Alliance IEEE
802.11i standard, which includes CCMP (AES), and TKIP encryption. The
Enterprise mode requires the use of a RADIUS server to authenticate users.
This security mode is backwards-compatible with wireless clients that support
the original WPA.
These parameters configure WPA Enterprise:
•
WPA Versions—The types of client stations to be supported:
-
WPA—If all client stations on the network support the original WPA but
none support the newer WPA2, and then select WPA.
-
WPA2—If all client stations on the network support WPA2, we suggest
using WPA2 which provides the best security per the IEEE 802.11i
standard.
-
WPA and WPA2—If you have a mix of clients, some of which support
WPA2 and others which support only the original WPA, select both WPA
and WPA2. This setting lets both WPA and WPA2 client stations
associate and authenticate, but uses the more robust WPA2 for clients
who support it. This WPA configuration allows more interoperability, in
place of some security.
•
Enable pre-authentication—If for WPA Versions you select only WPA2 or
both WPA and WPA2, you can enable pre-authentication for WPA2 clients.
Click Enable pre-authentication if you want WPA2 wireless clients to send
pre-authentication packets. The pre-authentication information is relayed
from the WAP device that the client is currently using to the target WAP
device. Enabling this feature can help speed up authentication for roaming
clients who connect to multiple APs.
This option does not apply if you selected WPA for WPA Versions because
the original WPA does not support this feature.
•
Cipher Suites—The cipher suite you want to use:
-
-
-
TKIP
CCMP (AES)
TKIP and CCMP (AES)
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
83
Wireless
Networks
5
By default both TKIP and CCMP are selected. When both TKIP and CCMP
are selected, client stations configured to use WPA with RADIUS must have
one of these addresses and keys:
-
-
A valid TKIP RADIUS IP address and RADIUS Key
A valid CCMP (AES) IP address and RADIUS Key
•
Use Global RADIUS Server Settings—By default, each VAP uses the
global RADIUS settings that you define for the WAP device (see RADIUS
RADIUS servers.
To use the global RADIUS server settings, make sure the check box is
selected.
To use a separate RADIUS server for the VAP, uncheck the box and enter the
RADIUS server IP address and key in these fields:
•
•
Server IP Address Type—The IP version that the RADIUS server uses.
You can toggle between the address types to configure IPv4 and IPv6
global RADIUS address settings, but the WAP device contacts only the
RADIUS server or servers for the address type that you select in this field.
Server IP Address 1 or Server IPv6 Address 1—The address for the
primary RADIUS server for this VAP.
If IPv4 is selected as the Server IP Address Type, enter the IP address of
the RADIUS server that all VAPs use by default, for example, 192.168.10.23.
If IPv6 is selected, enter the IPv6 address of the primary global RADIUS
server, for example, 2001:DB8:1234::abcd.
•
•
Server IP Address 2 to 4 or Server IPv6 Address 2 to 4—Up to three IPv4
and/or IPv6 addresses to use as the backup RADIUS servers for this VAP.
If authentication fails with the primary server, each configured backup
server is tried in sequence.
Key 1—The shared secret key for the global RADIUS server. You can use up
to 63 standard alphanumeric and special characters. The key is case
sensitive, and you must configure the same key on the WAP device and on
your RADIUS server. The text you enter is shown as asterisks to prevent
others from seeing the RADIUS key as you type.
•
Key 2 to Key 4—The RADIUS key associated with the configured backup
RADIUS servers. The server at Server IP (IPv6) Address 2 uses Key 2, the
server at Server IP (IPv6) Address 3 uses Key 3, and so on.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
84
Wireless
Scheduler
5
•
•
Enable RADIUS Accounting—Tracks and measures the resources a
particular user has consumed such as system time, amount of data
transmitted and received, and so on.
If you enable RADIUS accounting, it is enabled for the primary RADIUS
server and all backup servers.
Active Server—Enables the administrative selection of the active RADIUS
server, rather than having the WAP device attempt to contact each
configured server in sequence and choose the first server that is up.
Broadcast Key Refresh Rate—The interval at which the broadcast (group)
key is refreshed for clients associated with this VAP.
The default is 300 seconds. The valid range is from 0 to 86400 seconds. A
value of 0 indicates that the broadcast key is not refreshed.
•
Session Key Refresh Rate—The interval at which the WAP device
refreshes session (unicast) keys for each client associated with the VAP.
The valid range is from 0 to 86400 seconds. A value of 0 indicates that the
session key is not refreshed.
Scheduler
The Radio and VAP Scheduler allows you to configure a rule with a specific time
interval for VAPs or radios to be operational, which automates the enabling or
disabling of the VAPs and radio.
One way you can use this feature is to schedule the radio to operate only during
the office working hours in order to achieve security and reduce power
consumption. You can also use the Scheduler to allow access to VAPs for wireless
clients only during specific times of day.
The WAP device supports up to 16 profiles. Only valid rules are added to the
profile. Up to 16 rules are grouped together to form a scheduling profile. Periodic
time entries belonging to the same profile cannot overlap.
Adding Scheduler Profiles
You can create up to 16 scheduler profile names. By default, no profiles are
created.
To view Scheduler status and add a Scheduler profile:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
85
Wireless
Scheduler
5
STEP 1 Select Wireless > Scheduler in the navigation pane.
STEP 2 Ensure that the Administrative Mode is enabled. By default it is disabled.
The Scheduler Operational Status area indicates the current operation status of
the Scheduler:
•
Status—The operational status of the Scheduler. The range is Up or Down.
The default is Down.
•
Reason—The reason for the scheduler operational status. Possible values
are:
-
-
IsActive—The scheduler is administratively enabled.
ConfigDown—Operational status is down because global configuration
is disabled.
-
TimeNotSet—Time is not set on the WAP device either manually or
through NTP.
STEP 3 To add a profile, enter a profile name in the Scheduler Profile Configuration text
box and click Add. The profile name can be up to 32 alphanumeric characters.
Configuring Scheduler Rules
You can configure up to 16 rules for a profile. Each rule specifies the start time, end
time and day (or days) of the week the radio or VAP can be operational. The rules
are periodic in nature and are repeated every week. A valid rule must contain all of
the parameters (days of the week, hour, and minute) for the start time and the end
time. Rules cannot conflict; for example, you can configure one rule to start on each
weekday and another to start on each weekend day, but you cannot configure one
rule to begin daily and another rule to begin on weekends.
To configure a rule for a profile:
STEP 1 Select the profile from the Select a Profile Name list.
STEP 2 Click Add Rule.
The new rule shows in the rule table.
STEP 3 Check the box next to the Profile Name and click Edit.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
86
Wireless
Scheduler Association
5
STEP 4 From the Day of the Week menu, select the recurring schedule for the rule. You
can configure the rule to occur daily, each weekday, each weekend day (Saturday
and Sunday), or any single day of the week.
STEP 5 Set the start and end times:
•
•
Start Time—The time when the radio or VAP is operationally enabled. The
time is in HH:MM 24-hour format. The range is <00-23>:<00-59>. The default
is 00:00.
End Time—The time when the radio or VAP is operationally disabled. The
time is in HH:MM 24-hour format. The range is <00-23>:<00-59>. The default
is 00:00.
STEP 6 Click Save. The changes are saved to the Startup Configuration.
NOTE A Scheduler profile must be associated with a radio interface or a VAP interface to
NOTE To delete a rule, select the profile from the Profile Name column and click Delete.
Scheduler Association
The Scheduler profiles need to be associated with the WLAN interface or a VAP
interface to be effective. By default, there are no Scheduler profiles created, and
no profile is associated with any radio or VAP.
Only one Scheduler profile can be associated with the WLAN interface or each
VAP. A single profile can be associated with multiple VAPs. If the Scheduler profile
associated with a VAP or the WLAN interface is deleted, then the association is
removed.
To associate a Scheduler profile with the WLAN interface or a VAP:
STEP 1 Select Wireless > Scheduler Association in the navigation pane.
STEP 2 For the WLAN interface or a VAP, select the profile from the Profile Name list.
The Interface Operational Status column shows whether the interface is
currently enabled or disabled.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
87
Wireless
Bandwidth Utilization
5
Bandwidth Utilization
Use the Bandwidth Utilization page to configure how much of the radio bandwidth
can be used before the WAP device stops allowing new client associations. This
feature is disabled by default.
To enable bandwidth utilization:
STEP 1 Select Wireless > Bandwidth Utilization in the navigation pane.
STEP 2 Click Enable for the Bandwidth Utilization setting.
STEP 3 In the Maximum Utilization Threshold box, enter the percentage of network
bandwidth utilization allowed on the radio before the WAP device stops accepting
new client associations.
The valid integer range is from 0 to 100 percent. The default is 70 percent. When
set to 0, all new associations are allowed regardless of the utilization rate.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
NOTE After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
MAC Filtering
Media Access Control (MAC) filtering can be used to exclude or allow only listed
client stations to authenticate with the access point. MAC authentication is
is configured, the WAP device may refer to a MAC filter list stored on an external
RADlUS server, or may refer a MAC filter list stored locally on the WAP device.
Configuring a MAC Filter List Locally on the WAP Device
The WAP device supports one local MAC filter list only; that is, the same list
applies to all VAPs that are enabled to use the local list. The filter can be
configured to grant access only to the MAC addresses on the list, or to deny
access only to addresses on the list.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
88
Wireless
MAC Filtering
5
Up to 512 MAC addresses can be added to the filter list.
To configure MAC filtering:
STEP 1 Select Wireless > MAC Filtering in the navigation pane.
STEP 2 Select how the WAP device uses the filter list:
•
Allow only stations in the list—Any station that is not in the Stations List is
denied access to the network through the WAP device.
•
Block all stations in list—Only the stations that appear in the list are denied
access to the network through the WAP device. All other stations are
permitted access.
NOTE The filter setting also applies to the MAC filtering list stored on the
RADIUS server, if one exists.
STEP 3 In the MAC Address field, enter the MAC address to allow or block and click Add.
The MAC address appears in the Stations List.
STEP 4 Continue entering MAC addresses until the list is complete, and then click Save.
The changes are saved to the Startup Configuration.
NOTE To remove a MAC address from the Stations List, select it and then click Remove.
NOTE After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
Configuring MAC Authentication on the RADIUS Server
If one or more VAPs are configured to use a MAC filter stored on a RADIUS
authentication server, you must configure the station list on the RADIUS server. The
format for the list is described in this table:
RADIUS Server
Attribute
Description
Value
User-Name (1)
MAC address of the client station. Valid Ethernet MAC
address.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
89
Wireless
WDS Bridge
5
RADIUS Server
Attribute
Description
Value
User-Password (2)
A fixed global password used to
look up a client MAC entry.
NOPASSWORD
WDS Bridge
The Wireless Distribution System (WDS) allows you to connect multiple WAP121
and WAP321 devices. With WDS, access points communicate with one another
without wires. This capability is critical in providing a seamless experience for
roaming clients and for managing multiple wireless networks. It can also simplify
the network infrastructure by reducing the amount of cabling required. You can
configure the WAP device in point-to-point or point-to-multipoint bridge mode
based on the number of links to connect.
In the point-to-point mode, the WAP device accepts client associations and
communicates with wireless clients and other repeaters. The WAP device
forwards all traffic meant for the other network over the tunnel that is established
between the access points. The bridge does not add to the hop count. It functions
as a simple OSI Layer 2 network device.
In the point-to-multipoint bridge mode, one WAP device acts as the common link
between multiple access points. In this mode, the central WAP device accepts
client associations and communicates with the clients and other repeaters. All
other access points associate only with the central WAP device that forwards the
packets to the appropriate wireless bridge for routing purposes.
The WAP device can also act as a repeater. In this mode, the WAP device serves
as a connection between two WAP devices that might be too far apart to be within
cell range. When acting as a repeater, the WAP device does not have a wired
connection to the LAN and repeats signals by using the wireless connection. No
special configuration is required for the WAP device to function as a repeater, and
there are no repeater mode settings. Wireless clients can still connect to an WAP
device that is operating as a repeater.
Before you configure WDS on the WAP device, note these guidelines:
•
•
WDS only works with Cisco WAP121 and Cisco WAP321 devices.
All Cisco WAP devices participating in a WDS link must have the following
identical settings:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
90
Wireless
WDS Bridge
5
-
-
-
-
Radio
IEEE 802.11 Mode
Channel Bandwidth
Channel (Auto is not recommended)
NOTE When operating bridging in the 802.11n 2.4 GHz band, set the Channel
Bandwidth to 20 MHz, rather than the default 20/40 MHz. In the 2.4 GHz
20/40 MHz band, the operating bandwidth can change from 40 MHz to
20 MHz if any 20 MHz WAP devices are detected in the area. The
mismatched channel bandwidth can cause the link to disconnect.
•
•
When using WDS, be sure to configure WDS on both WAP devices
participating in the WDS link.
You can have only one WDS link between any pair of WAP devices. That is,
a remote MAC address may appear only once on the WDS page for a
particular WAP device.
To configure a WDS bridge:
STEP 1 Select Wireless > WDS Bridge in the navigation pane.
STEP 2 Select Enable for Spanning Tree Mode. When enabled, STP helps prevent
switching loops. STP is recommended if you configure WDS links.
STEP 3 Select Enable for WDS Interface.
STEP 4 Configure the remaining parameters:
•
Remote MAC Address—Specifies the MAC address of the destination WAP
device; that is, the WAP device on the other end of the WDS link to which
data is sent or handed-off and from which data is received.
TIP You can find the MAC address on the Status and Statistics > Network
Interface page.
•
Encryption—The type of encryption to use on the WDS link; it does not have
to match the VAP you are bridging. The WDS Encryption settings are unique
to the WDS bridge. The options are none, WEP, and WPA Personal.
If you are unconcerned about security issues on the WDS link, you may
decide not to set any type of encryption. Alternatively, if you have security
concerns you can choose between Static WEP and WPA Personal. In WPA
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
91
Wireless
WDS Bridge
5
Personal mode, the WAP device uses WPA2-PSK with CCMP (AES)
encryption over the WDS link. See WEP on WDS Links or WPA/PSK on
WDS Links following this procedure for more information about encryption
options.
STEP 5 Repeat these steps for up to three additional WDS interfaces.
STEP 6 Click Save. The changes are saved to the Startup Configuration.
STEP 7 Replicate this procedure on the other device or devices connecting to the bridge.
TIP You can verify that the bridge link is up by going to the Status and Statistics
> Network Interface page. In the Interface Status table, the WLAN0:WDS(x)
status should state Up.
!
CAUTION After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
WEP on WDS Links
These additional fields appear when you select WEP as the encryption type.
•
Key Length—If WEP is enabled, specify the length of the WEP key as
64 bits or 128 bits.
•
•
Key Type—If WEP is enabled, specify the WEP key type: ASCII or Hex.
WEP Key—If you selected ASCII, enter any combination of 0 to 9, a to z,
and A to Z. If you selected Hex, enter hexadecimal digits (any combination
of 0 to 9 and a to f or A to F). These are the RC4 encryption keys shared with
the stations using the WAP device.
Note that the required number of characters is indicated to the right of the
field and changes based on your selections in the Key Type and Key
Length fields.
WPA/PSK on WDS Links
These additional fields appear when you select WPA/PSK as the encryption type.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
92
Wireless
WorkGroup Bridge
5
•
•
WDS ID—Enter an appropriate name for the new WDS link you have
created. It is important that the same WDS ID is also entered at the other
end of the WDS link. If this WDS ID is not the same for both WAP devices on
the WDS link, they will not be able to communicate and exchange data.
The WDS ID can be any alphanumeric combination.
Key—Enter a unique shared key for the WDS bridge. This unique shared
key must also be entered for the WAP device at the other end of the WDS
link. If this key is not the same for both WAPs, they will not be able to
communicate and exchange data.
The WPA-PSK key is a string of at least 8 characters to a maximum of 63
characters. Acceptable characters include uppercase and lowercase
alphabetic letters, the numeric digits, and special symbols such as @ and #.
WorkGroup Bridge
The WAP device WorkGroup Bridge feature enables the WAP device to extend the
accessibility of a remote network. In WorkGroup Bridge mode, the WAP device
acts as a wireless station (STA) on the wireless LAN. It can bridge traffic between
a remote wired network or associated wireless clients and the wireless LAN that
is connected using the WorkGroup Bridge mode.
The WorkGroup Bridge feature enables support for STA-mode and AP-mode
operation simultaneously. The WAP device can operate in one Basic Service Set
(BSS) as an STA device while operating on another BSS as a WAP device. When
WorkGroup Bridge mode is enabled, the WAP device supports only one BSS for
wireless clients that associate with it, and another BSS with which the WAP
device associates as a wireless client.
It is recommended that WorkGroup Bridge mode be used only when the WDS
bridge feature cannot be operational with a peer WAP device. WDS is a better
solution and is preferred over the WorkGroup Bridge solution. Use WDS if you are
bridging Cisco WAP121 and WAP321 devices. If you are not, then consider
WorkGroup Bridge. When the WorkGroup Bridge feature is enabled, the VAP
configurations are not applied; only the WorkGroup Bridge configuration is
applied.
NOTE The WDS feature does not work when the WorkGroup Bridge mode is enabled on
the WAP device.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
93
Wireless
WorkGroup Bridge
5
In WorkGroup Bridge mode, the BSS managed by the WAP device while operating
in WAP device mode is referred to as the access point interface, and associated
STAs as downstream STAs. The BSS managed by the other WAP device (that is,
the one to which the WAP device associates as an STA) is referred to as the
infrastructure client interface, and the other WAP device is referred as the
upstream AP.
The devices connected to the wired interface of the WAP device, as well as the
downstream stations associated with the access point interface of the device, can
access the network connected by the infrastructure client interface. To allow the
bridging of packets, the VLAN configuration for the access point interface and
wired interface should match that of the infrastructure client interface.
WorkGroup Bridge mode can be used as range extender to enable the BSS to
provide access to remote or hard-to-reach networks. A single-radio can be
configured to forward packets from associated STAs to another WAP device in the
same ESS, without using WDS.
Before you configure WorkGroup Bridge on the WAP device, note these
guidelines:
•
All WAP devices participating in WorkGroup Bridge must have the following
identical settings:
-
-
-
-
Radio
IEEE 802.11 Mode
Channel Bandwidth
Channel (Auto is not recommended)
WorkGroup Bridge mode currently supports only IPv4 traffic.
•
•
WorkGroup Bridge mode is not supported across a Single Point Setup.
To configure WorkGroup Bridge mode:
STEP 1 Select Wireless > WorkGroup Bridge in the navigation pane.
STEP 2 Select Enable for the WorkGroup Bridge Mode.
STEP 3 Configure these parameters for the Infrastructure Client Interface (upstream):
•
SSID—The SSID of the BSS.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
94
Wireless
WorkGroup Bridge
5
NOTE There is an arrow next to SSID for SSID Scanning; this feature is
disabled by default, and is enabled only if AP Detection is enabled in Rogue
AP Detection (which is also disabled by default).
•
Security—The type of security to use for authenticating as a client station
on the upstream WAP device. Choices are:
-
-
-
-
None
Static WEP
WPA Personal
WPA Enterprise
Personal security settings.
•
VLAN ID—The VLAN associated with the BSS.
NOTE The Infrastructure Client Interface will be associated with the
upstream WAP device with the configured credentials. The WAP device may
obtain its IP address from a DHCP server on the upstream link. Alternatively,
you can assign a static IP address. The Connection Status field indicates
whether the WAP is connected to the upstream WAP device. You can click
the Refresh button at the top of the page to view the latest connection
status.
STEP 4 Configure the following additional fields for the Access Point Interface:
•
•
Status—Select Enable for the Access Point Interface.
SSID—The SSID for the Access Point Interface does not need to be the
same as the Infrastructure Client SSID. However, if attempting to support a
roaming type of scenario, the SSID and security must be the same.
•
•
SSID Broadcast—Select if you want the downstream SSID to be broadcast.
SSID Broadcast is enabled by default.
Security—The type of security to use for authenticating. Choices are:
-
-
-
None
Static WEP
WPA Personal
•
MAC Filtering—Select one of these options:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
95
Wireless
Quality of Service
5
-
-
-
Disabled—The set of clients in the APs BSS that can access the
upstream network is not restricted to the clients specified in a MAC
address list.
Local—The set of clients in the APs BSS that can access the upstream
network is restricted to the clients specified in a locally defined MAC
address list.
RADIUS—The set of clients in the APs BSS that can access the upstream
network is restricted to the clients specified in a MAC address list on a
RADIUS server.
the MAC filter list.
•
VLAN ID—Configure the Access Point Interface with the same VLAN ID as
advertised on the Infrastructure Client Interface.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
The associated downstream clients now have connectivity to the upstream
network.
Quality of Service
The quality of service (QoS) settings provide you with the ability to configure
transmission queues for optimized throughput and better performance when
handling differentiated wireless traffic, such as Voice-over-IP (VoIP), other types of
audio, video, streaming media, and traditional IP data.
To configure QoS on the WAP device, you set parameters on the transmission
queues for different types of wireless traffic and specify minimum and maximum
wait times (through contention windows) for transmission.
WAP Enhanced Distributed Channel Access (EDCA) parameters affect traffic
flowing from the WAP device to the client station.
Station EDCA parameters affect traffic flowing from the client station to the WAP
device.
In normal use, the default values for the WAP device and station EDCA should not
need to be changed. Changing these values affects the QoS provided.
To configure WAP device and Station EDCA parameters:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
96
Wireless
Quality of Service
5
STEP 1 Select Wireless > QoS in the navigation pane.
STEP 2 Select an option from the EDCA Template list:
•
•
•
WFA Defaults—Populates the WAP device and Station EDCA parameters
with WiFi Alliance default values, which are best for general, mixed traffic.
Optimized for Voice—Populates the WAP device and Station EDCA
parameters with values that are best for voice traffic.
Custom—Enables you to choose custom EDCA parameters.
These four queues are defined for different types of data transmitted from WAP-
to-station. If you choose a Custom template, the parameters that define the queues
are configurable; otherwise, they are set to predefined values appropriate to your
selection. The four queues are:
•
•
•
•
Data 0 (Voice)—High priority queue, minimum delay. Time-sensitive data
such as VoIP and streaming media are automatically sent to this queue.
Data 1 (Video)—High priority queue, minimum delay. Time-sensitive video
data is automatically sent to this queue.
Data 2 (Best Effort)—Medium priority queue, medium throughput and delay.
Most traditional IP data is sent to this queue.
Data 3 (Background)—Lowest priority queue, high throughput. Bulk data that
requires maximum throughput and is not time-sensitive is sent to this queue
(FTP data, for example).
STEP 3 Configure the following EDCA and Station EDCA parameters:
NOTE These parameters are configurable only if you selected Custom in the
previous step.
•
•
Arbitration Inter-Frame Space—A wait time for data frames. The wait time
is measured in slots. Valid values for AIFS are 1 through 255.
Minimum Contention Window—An input to the algorithm that determines
the initial random backoff wait time (window) for retry of a transmission.
This value is the upper limit (in milliseconds) of a range from which the initial
random backoff wait time is determined.
The first random number generated is a number between 0 and the number
specified here.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
97
Wireless
Quality of Service
5
If the first random backoff wait time expires before the data frame is sent, a
retry counter is incremented and the random backoff value (window) is
doubled. Doubling continues until the size of the random backoff value
reaches the number defined in the Maximum Contention Window.
Valid values are 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1024. This value must be
lower than the value for the Maximum Contention Window.
•
•
•
Maximum Contention Window—The upper limit (in milliseconds) for the
doubling of the random backoff value. This doubling continues until either the
data frame is sent or the Maximum Contention Window size is reached.
After the Maximum Contention Window size is reached, retries continue until
a maximum number of retries allowed is reached.
Valid values are 1, 3, 7, 15, 31, 63, 127, 255, 511, or 1024. This value must be
higher than the value for the Minimum Contention Window.
Maximum Burst (WAP only)—A WAP EDCA parameter that applies only to
traffic flowing from the WAP to the client station.
This value specifies (in milliseconds) the maximum burst length allowed for
packet bursts on the wireless network. A packet burst is a collection of
multiple frames transmitted without header information. The decreased
overhead results in higher throughput and better performance.
Valid values are 0.0 through 999.
Wi-Fi MultiMedia (WMM)—Select Enable to enable Wi-Fi MultiMedia
(WMM) extensions. This field is enabled by default. With WMM enabled, QoS
prioritization and coordination of wireless medium access is on. With WMM
enabled, QoS settings on the WAP device control downstream traffic
flowing from the WAP device to client station (AP EDCA parameters) and the
upstream traffic flowing from the station to the AP (station EDCA
parameters).
Disabling WMM deactivates QoS control of station EDCA parameters on
upstream traffic flowing from the station to the WAP device. With WMM
disabled, you can still set some parameters on the downstream traffic
flowing from the WAP device to the client station (AP EDCA parameters).
•
TXOP Limit (Station only)—The TXOP Limit is a station EDCA parameter and
only applies to traffic flowing from the client station to the WAP device. The
Transmission Opportunity (TXOP) is an interval of time, in milliseconds, when
a WME client station has the right to initiate transmissions onto the wireless
medium (WM) towards the WAP device. The TXOP Limit maximum value is
65535.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
98
Wireless
WPS Setup
5
STEP 4 Configure the following additional settings:
•
No Acknowledgement—Select Enable to specify that the WAP device
should not acknowledge frames with QosNoAck as the service class value.
•
Unscheduled Automatic Power Save Delivery—Select Enable to enable
APSD, which is a power management method. APSD is recommended if
VoIP phones access the network through the WAP device.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
!
CAUTION After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
WPS Setup
This section describes the Wi-Fi Protected Setup (WPS) protocol and its
configuration on the WAP device.
WPS Overview
WPS is a standard that enables simple establishment of wireless networks
without compromising network security. It relieves both the wireless client users
and the WAP device administrators from having to know network names, keys, and
various other cryptographic configuration options.
WPS facilitates network setup by allowing the administrator to use a push button
or PIN to establish wireless networks, which avoids the manual entry of network
names (SSIDs) and wireless security parameters:
•
Push button: The WPS button is either on the product or a clickable button
on the user interface.
•
Personal Identification Number (PIN): The PIN can be viewed in the
product user interface.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
99
Wireless
WPS Setup
5
WPS maintains network security by requiring both the users of new client devices
and WLAN administrators to have either physical access to their respective
devices or secure remote access to these devices.
Usage Scenarios
These are typical scenarios for using WPS:
•
A user wishes to enroll a client station on a WPS-enabled WLAN. (The
enrolling client device may detect the network, and prompt the user to
enroll, although this is not necessary.) The user triggers the enrollment by
pushing a button on the client device. The WAP device's administrator then
pushes a button on the WAP device. During a brief exchange of WPS
protocol messages, the WAP device supplies the new client with a new
security configuration through Extensible Authentication Protocol (EAP).
The two devices disassociate, and then reassociate and authenticate with
the new settings.
•
•
A user wishes to enroll a client station on a WPS-enabled WLAN by
supplying the WAP device administrator with the PIN of the client device.
The administrator enters this PIN in the configuration utility of the WAP
device and triggers the device enrollment. The new enrollee and the WAP
device exchange WPS messages, including a new security configuration,
disassociate, reassociate, and authenticate.
A WAP device administrator purchases a new WAP device that has been
certified by the Wi-Fi Alliance to be compliant with WPS version 2.0, and
wishes to add the WAP device to an existing (wired or wireless) network.
The administrator turns on the WAP device, and then accesses a network
host that supports the WPS registration protocol. The administrator enters
the PIN of the WAP device in the configuration utility of this external
registrar, and triggers the WPS registration process. (On a wired LAN, the
WPS protocol messages are transported through Universal Plug and Play,
or UPnP, protocol.) The host registers the WAP as a new network device and
configures the WAP with new security settings.
•
•
A WAP device administrator has just added a new WAP device to an
existing (wireless or wired) network through WPS, and wishes to grant
network access to a new client device. The device is enrolled through
either the PIN or Push-Button Control (PBC) methods described above, but
this time the device enrolls with the external registrar, with the WAP device
acting solely as a proxy.
A wireless device that does not support WPS must join the WPS-enabled
WLAN. The administrator, who cannot use WPS in this case, instead
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
100
Wireless
WPS Setup
5
manually configures the device with the SSID, public shared key, and
cryptography modes of the WPS-enabled WAP device. The device joins
the network.
The PIN is either an eight-digit number that uses its last digit as a checksum value,
or a four-digit number with no checksum. Each of these numbers may contain
leading zeroes.
WPS Roles
The WPS standard assigns specific roles to the various components in its
architecture:
•
•
•
Enrollee—A device that can join the wireless network.
AP—A device that provides wireless access to the network.
Registrar—An entity that issues security credentials to enrollees and
configures APs.
The WAP devices act as AP devices and support a built-in registrar. They do not
function as an enrollee.
Enabling and Disabling WPS on a VAP
The administrator can enable or disable WPS on only one VAP. WPS is operational
only if this VAP meets these conditions:
•
•
•
•
The WAP device is configured to broadcast the VAP SSID.
MAC address filtering is disabled on the VAP.
WEP encryption is disabled on the VAP.
The VAP is configured to use either WPA-Personal security or none. If
WPA2-PSK encryption mode is enabled, then a valid pre-shared key (PSK)
must be configured and CCMP (AES) encryption must be enabled.
•
The VAP is operationally enabled.
WPS is operationally disabled on the VAP if any of these conditions are not met.
NOTE Disabling WPS on a VAP does not cause disassociation of any clients previously
authenticated through WPS on that VAP.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
101
Wireless
WPS Setup
5
External and Internal Registration
It is not necessary for the WAP devices to handle the registration of clients on the
network themselves. The WAP device can either use its built-in registrar, or act as
a proxy for an external registrar. The external registrar may be accessed through
the wired or wireless LAN. An external registrar may also configure the SSID,
encryption mode, and public shared key of a WPS-enabled BSS. This capability is
very useful for out-of-box deployments; that is, when an administrator simply
attaches a new WAP device to a LAN for the first time.
If the WAP device is using a built-in registrar, it enrolls new clients using the
configuration of the VAP associated with the WPS service, whether this
configuration was configured directly on the WAP device or acquired by an
external registrar through WPS.
Client Enrollment
Push-button Control
The WAP device enrolls 802.11 clients through WPS by one of two methods: the
Push-Button Control (PBC) method, or the Personal Identification Number (PIN)
method.
The PBC method is when the user of a prospective client pushes a button on the
enrolling device, and the administrator of the WAP device with an enabled built-in
registrar pushes a similar (hardware or software) button. This sequence begins the
enrollment process, and the client device joins the network. Although the Cisco
WAP devices do not support an actual hardware button, the administrator can
initiate the enrollment for a particular VAP using a software button in the web-
based configuration utility.
NOTE There is no defined order in which the buttons on the client device and WAP device
must be pressed. Either device can initiate the enrollment. However, if the software
button on the WAP device is pressed, and no client attempts to enroll after 120
seconds, the WAP device terminates the pending WPS enrollment transaction.
PIN Control
A client may also enroll with a registrar by using a PIN. For example, the WAP
device administrator may start an enrollment transaction for a particular VAP by
entering the PIN of a client. When the client detects the WPS-enabled device, the
user can then supply its PIN to the WAP device to continue the enrollment process.
After the WPS protocol has completed, the client securely joins the network. The
client can also initiate this process.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
102
Wireless
WPS Setup
5
As with the PBC method, if the WAP device begins the enrollment transaction and
no client attempts to enroll after 120 seconds, the WAP device terminates the
pending transaction.
Optional Use of Built-In Registrar
Although the WAP device supports a built-in registrar for WPS, its use is optional.
After an external registrar has configured the WAP device, the WAP device acts as
a proxy for that external registrar, regardless if the built-in registrar of the WAP
device is enabled (it is enabled by default).
Lockdown Capability
Each WAP device stores a WPS-compatible device PIN in nonvolatile RAM. WPS
requires this PIN if an administrator wants to allow an unconfigured WAP device
(that is, one with only factory defaults, including WPS being enabled on a VAP) to
join a network. In this scenario, the administrator obtains the PIN value from the
configuration utility of the WAP device.
The administrator may wish to change the PIN if network integrity has been
compromised in some way. The WAP device provides a method for generating a
new PIN and storing this value in NVRAM. If the value in NVRAM is corrupted,
erased, or missing, a new PIN is generated by the WAP device and stored in
NVRAM.
The PIN method of enrollment is potentially vulnerable by way of brute force
attacks. A network intruder could try to pose as an external registrar on the
wireless LAN and attempt to derive the PIN value of the WAP device by
exhaustively applying WPS-compliant PINs. To address this vulnerability, in the
event that a registrar fails to supply a correct PIN in three attempts within 60
seconds, the WAP device prohibits any further attempts by an external registrar to
register with the WAP device on the WPS-enabled VAP for 60 seconds. The
lockdown duration increases upon subsequent failures, up to a maximum of 64
minutes. The WAP devices registration functionality goes into permanent
lockdown after the 10th consecutive failed attempt. Reset the device to restart the
registration functionality.
However, wireless client stations may enroll with the WAP device's built-in
registrar, if enabled, during this lockdown period. The WAP device also continues
to provide proxy services for enrollment requests to external registrars.
The WAP device has an additional security features for protecting its device PIN.
After the WAP device has completed registration with an external registrar, and
the resulting WPS transaction has concluded, the device PIN is automatically
regenerated.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
103
Wireless
WPS Setup
5
VAP Configuration Changes
The WPS protocol can configure the following parameters for a WPS-enabled VAP
on a WAP device:
•
•
•
•
Network SSID
Key management options (WPA-PSK, or WPA-PSK and WPA2-PSK)
Cryptography options (CCMP/AES, or TKIP and CCMP/AES)
Network (public shared) key
If a VAP is enabled for WPS, these configuration parameters are subject to change,
and are persistent between reboots of the WAP device.
External Registration
The WAP device supports registration with WPS External Registrars (ER) on the
wired and wireless LAN. On the WLAN, external registrars advertise their
capabilities within WPS-specific Information Elements (IEs) of their beacon frames;
on the wired LAN, external registrars announce their presence through UPnP.
WPS v2.0 does not require registration with an ER through the user interface. The
administrator can register the WAP device with an ER by:
STEP 1 Entering the ER PIN on the WAP device.
STEP 2 Entering the WAP device PIN on the user interface of the ER.
NOTE The registration process can also configure the WAP device as specified in the VAP
Configuration Changes section, if the WAP device has declared within the WPS-
specific IEs of its beacon frames or UPnP messages that it requires such
configuration.
The WAP device can serve as a proxy for up to three external registrars
simultaneously.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
104
Wireless
WPS Setup
5
Exclusive Operation of WPS Transactions
Any one VAP on the WAP device can be enabled for WPS. At most, one WPS
transaction (for example, enrollment and association of an 802.11 client) can be in
progress at a time on the WAP device. The WAP device administrator can
terminate the transaction in progress from the web-based configuration utility. The
configuration of the VAP, however, should not be changed during the transaction;
nor should the VAP be changed during the authentication process. This restriction
is recommended but not enforced on the WAP device.
Backward Compatibility with WPS Version 1.0
Although WAP devices support WPS version 2.0, the WAP device interoperates
with enrollees and registrars that are certified by the Wi-Fi Alliance to conform to
version 1.0 of the WPS protocol.
Configuring WPS Settings
You can use the WPS Setup page to enable the WAP device as a WPS-capable
device and configure basic settings. When you are ready to use the feature to
enroll a new device or add the WAP device to a WPS-enabled network, use the
WPS Process page.
!
CAUTION For security reasons, it is recommended, but not required, that you use an HTTPS
connection to the web-based configuration utility when configuring WPS.
To configure the WAP device as a WPS-capable device:
STEP 1 Select Wireless > WPS Setup in the navigation pane.
The WPS Setup page shows global parameters and status, and parameters and
status of the WPS instance. An instance is an implementation of WPS that is
associated with a VAP on the network. The WAP device supports one instance
only.
STEP 2 Configure the global parameters:
•
Supported WPS Version—The WPS protocol version that the WAP device
supports.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
105
Wireless
WPS Setup
5
•
WPS Device Name—Provides a default device name. You can assign a
different name from 1 to 32 characters, including spaces and special
characters.
•
•
WPS Global Operational Status—Whether the WPS protocol is enabled or
disabled on the WAP device. It is enabled by default.
WPS Device PIN—A system-generated eight-digit WPS PIN for the WAP
device. The administrator may use this generated PIN to register the WAP
device with an external registrar.
You can click Generate to generate a new PIN. Generating a new pin is
advisable if network integrity has been compromised.
STEP 3 Configure the WPS instance parameters:
•
WPS Instance ID—An identifier for the instance. As there is only one
instance, the only option is wps1.
•
•
•
WPS Mode—Enables or disables the instance.
WPS VAP—The VAP associated with this WPS instance.
WPS Built-in Registrar—Enables the built-in registrar function. When
enabled, enrollees (typically WLAN clients) can register with the WAP
device. When disabled, the registrar functionality in the WAP device is
turned off and the enrollee needs to register with another registrar on the
network. In this case, another device on the network acts as the registrar and
the WAP device serves as a proxy for forwarding client registration requests
and the responses of the registrar.
•
WPS Configuration State—Specifies if the VAP will be configured from the
external registrar as a part of WPS process. It can be set to one of these
values:
-
Unconfigured—VAP settings are configured using WPS, after which the
state will be change to Configured.
-
Configured—VAP settings are not configured by the external registrar
and will retain the existing configuration.
STEP 4 Click Update. The changes are saved to the Startup Configuration.
The operational status of the instance and the reason for that status appears. See
Enabling or Disabling WPS on a VAP for information about conditions that may
cause the instance to be disabled.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
106
Wireless
WPS Process
5
Instance Status
The Instance Status area shows the following information about the selected WPS
instance:
•
•
WPS Operational Status—Whether or not the WPS instance is operational.
AP Lockdown Status—Whether the AP is in lockdown mode, in which
external registrars are blocked from registering with the AP. When in
lockdown status, this field reports the start time of the lockdown, whether it
is temporary or permanent, and if temporary, the duration of the lockdown
period. When not in lockdown mode, the status appears as Disabled.
•
Failed Attempts with Invalid PIN—The number of times an external
registrar has tried and failed to register with the WAP device.
When in lockdown status, the following fields appear:
•
AP Lockdown Duration—The duration in minutes for which the WAP is
locked. When the WAP is permanently locked, this value is set to –1.
•
AP Lockdown Timestamp—The time when the WAP device was locked.
You can click Refresh to update the page with the most recent status information.
WPS Process
You can use the WPS Process page to use WPA to enroll a client station on the
network. You can enroll a client using a pin or using the push button method, if
supported on the client station.
Enrolling a Client Using the PIN Method
To enroll a client station using the PIN method:
STEP 1 Obtain the PIN from the client device. The PIN may be printed on the hardware
itself, or may be obtained from the software interface of the device.
STEP 2 Select Wireless > WPS Process in the navigation pane.
STEP 3 Enter the PIN of the client in the PIN Enrollment text box and click Start.
STEP 4 Within two minutes, enter the WAP pin on the software interface of the client
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
107
Wireless
WPS Process
5
When you enter the PIN on the client device, the WPS Operational Status changes
to Adding Enrollee. When the enrollment process is complete, the WPS
Operational Status changes to Ready and the Transaction Status changes to
Success.
When the client is enrolled, either the built-in registrar of the WAP device or the
external registrar on the network proceeds to configure the client with the SSID,
encryption mode, and public shared key of a WPS-enabled BSS.
!
CAUTION This enrollment sequence may also work in reverse; that is, you may be able to
initiate the process on the client station by entering the pin of the WAP device.
However, this method is not recommended for security reasons, as it enables the
client to configure the SSID and security settings on the AP. The administrator
should only share the PIN with trusted devices.
Enrolling a Client Using the Push Button Method
To enroll a client station using the push button method:
STEP 1 Click Start next to PBC Enrollment.
STEP 2 Push the hardware button on the client station.
NOTE You can alternatively initiate this process on the client station and then click the PBC
Enrollment Start button on the WAP device.
When you push the button on the client station, the WPS Operational Status
changes to Adding Enrollee. When the enrollment process is complete, the WPS
Operational Status changes to Ready and the Transaction Status changes to
Success.
When the client is enrolled, either the built-in registrar of the WAP device or the
external registrar on the network proceeds to configure the client with the SSID,
encryption mode, and public shared key of a WPS-enabled BSS.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
108
Wireless
WPS Process
5
Viewing Instance Status Information
The Instance Status section shows the following information about the WPS
instance selected in the WPS Instance ID list:
•
•
WPS Status—Whether the selected WPS instance is enabled or disabled.
WPS Configuration State—Whether the VAP will be configured from the
external registrar as a part of the WPS process.
•
•
Transaction Status—The status of the last WPS transaction. The possible
values are None, Success, WPS Message Error, and Timed Out.
WPS Operational Status—The status of the current or most recent WPS
transaction. The possible values are Disabled, Ready, Configuring, Proxying,
and Adding Enrollee. When no WPS transactions have occurred since WPS
was enabled, Ready appears.
•
•
AP Lockdown Status—Whether the instance is currently in lockdown state.
Failed Attempts with Invalid PIN—The number of times an attempt at
authenticating an external registrar has failed due to an invalid password.
Viewing Instance Summary Information
This information appears for WPS instance:
•
•
•
•
WPS Radio
WPS VAP
SSID
Security
If the WPS Configuration State field on the WPS Setup page is set to
Unconfigured, then the SSID and Security values are configured by the external
registrar. If the field is set to Configured, then these values are configured by the
administrator.
NOTE You can click Refresh to update the page with the most recent status information.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
109
6
System Security
This chapter describes how to configure security settings on the WAP device
device.
It contains these topics:
•
•
•
•
RADIUS Server
Several features require communication with a RADIUS authentication server. For
example, when you configure Virtual Access Points (VAPs) on the WAP device, you
can configure security methods that control wireless client access (see the Radio
page). The Dynamic WEP and WPA Enterprise security methods use an external
RADIUS server to authenticate clients. The MAC address filtering feature, where
client access is restricted to a list, may also be configured to use a RADIUS server
to control access. The Captive Portal feature also uses RADIUS to authenticate
clients.
You can use the Radius Server page to configure the RADIUS servers that are
used by these features. You can configure up to four globally available IPv4 or IPv6
RADIUS servers; however, you must select whether the RADIUS client operates in
IPv4 or IPv6 mode with respect to the global servers. One of the servers always
acts as a primary while the others act as backup servers.
NOTE In addition to using the global RADIUS servers, you can also configure each VAP to
To configure global RADIUS servers:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
110
System Security
RADIUS Server
6
STEP 1 Select Security > RADIUS Server in the navigation pane.
STEP 2 Enter the parameters:
•
Server IP Address Type—The IP version that the RADIUS server uses.
You can toggle between the address types to configure IPv4 and IPv6 global
RADIUS address settings, but the WAP device contacts only the RADIUS
server or servers of the address type you select in this field.
•
Server IP Address 1 or Server IPv6 Address 1—The addresses for the
primary global RADIUS server.
When the first wireless client tries to authenticate with the WAP device, the
device sends an authentication request to the primary server. If the primary
server responds to the authentication request, the WAP device continues to
use this RADIUS server as the primary server, and authentication requests
are sent to the address specified.
•
•
Server IP Address (2 through 4) or Server IPv6 Address (2 through 4)—
Up to three backup IPv4 or IPv6 RADIUS server addresses.
If authentication fails with the primary server, each configured backup server
is tried in sequence.
Key 1—The shared secret key that the WAP device uses to authenticate to
the primary RADIUS server.
You can use from 1 to 64 standard alphanumeric and special characters. The
key is case sensitive and must match the key configured on the RADIUS
server. The text you enter appears as asterisks.
•
•
Key (2 through 4)—The RADIUS key associated with the configured backup
RADIUS servers. The server at Server IP (IPv6) Address 2 uses Key 2, the
server at Server IP (IPv6) Address-3 uses Key 3, and so on.
Enable RADIUS Accounting—Enables tracking and measuring of the
resources a particular user has consumed, such as system time, amount of
data transmitted and received, and so on.
If you enable RADIUS accounting, it is enabled for the primary RADIUS
server and all backup servers.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
111
System Security
802.1X Supplicant
6
802.1X Supplicant
IEEE 802.1X authentication enables the access point to gain access to a secured
wired network. You can enable the access point as an 802.1X supplicant (client) on
the wired network. A user name and password that are encrypted using the MD5
algorithm can be configured to allow the access point to authenticate using
802.1X.
On networks that use IEEE 802.1X port-based network access control, a
supplicant cannot gain access to the network until the 802.1X authenticator grants
access. If your network uses 802.1X, you must configure 802.1X authentication
information on the WAP device, so that it can supply it to the authenticator.
The 802.1X Supplicant page is divided into three areas: Supplicant Configuration,
Certificate File Status, and Certificate File Upload.
The Supplicant Configuration area enables you to configure the 802.1X
operational status and basic settings.
STEP 1 Select System Security > 802.1X Supplicant in the navigation pane.
STEP 2 Enter the parameters:
•
•
Administrative Mode—Enables the 802.1X supplicant functionality.
EAP Method—The algorithm to be used for encrypting authentication user
names and passwords.
-
-
MD5—A hash function defined in RFC 3748 that provides basic security.
PEAP—Protected Extensible Authentication Protocol, which provides a
higher level of security than MD5 by encapsulating it within a TLS tunnel.
-
TLS—Transport Layer Security, as defined in RFC 5216, an open
standard that provides a high level of security.
•
Username—The WAP device uses this username when responding to
requests from an 802.1X authenticator. The username can be 1 to 64
characters long. ASCII-printable characters are allowed, which includes
uppercase and lowercase alphabetic letters, numeric digits, and all special
characters except quotation marks.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
112
System Security
802.1X Supplicant
6
•
Password—The WAP device uses this MD5 password when responding to
requests from an 802.1X authenticator. The password can be 1 to 64
characters in length. ASCII-printable characters are allowed, which includes
uppercase and lowercase alphabetic letters, numeric digits, and all special
characters except quotation marks.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
NOTE After new settings are saved, the corresponding processes may be
stopped and restarted. When this happens, the WAP device may lose
connectivity. We recommend that you change WAP device settings when a
loss of connectivity will least affect your wireless clients.
The Certificate File Status area shows whether a current certificate exists:
•
Certificate File Present—Indicates whether the HTTP SSL Certificate file
is present. The field shows Yes if it is present. The default setting is No.
•
Certificate Expiration Date—Indicates when the HTTP SSL Certificate file
will expire. The range is a valid date.
The Certificate File Upload area enables you to upload a certificate file to the WAP
device:
STEP 1 Select either HTTP or TFTP as the Transfer Method.
STEP 2 If you selected HTTP, click Browse to select the file.
If you selected TFTP, enter the Filename and the TFTP Server IPv4 Address. The
filename cannot contain the following characters: spaces, <, >, |, \, : , (, ), &, ; , #, ? , *,
and two or more successive periods.
STEP 3 Click Upload.
A confirmation window appears, followed by a progress bar to indicate the status
of the upload.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
113
System Security
Password Complexity
6
Password Complexity
You can configure complexity requirements for passwords used to access the
WAP device configuration utility. Complex passwords increase security.
To configure password complexity requirements:
STEP 1 Select Security > Password Complexity in the navigation pane.
STEP 2 For the Password Complexity setting, select Enable.
STEP 3 Configure the parameters:
•
Password Minimum Character Class—The minimum number of character
classes that must be represented in the password string. The four possible
character classes are uppercase letters, lowercase letters, numbers, and
special characters available on a standard keyboard.
•
Password Different From Current—Select to have users enter a different
password when their current password expires. If not selected, users can
reenter the same password when it expires.
•
•
•
•
Maximum Password Length—The maximum password character length is
a range from 64 to 80. The default is 64.
Minimum Password Length—The minimum password character length is a
range from 0 to 32. The default is 8.
Password Aging Support—Select to have passwords expire after a
configured time period.
Password Aging Time—The number of days before a newly created
password expires, from 1 to 365. The default is 180 days.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
114
System Security
WPA-PSK Complexity
6
WPA-PSK Complexity
When you configure VAPs on the WAP device, you can select a method of
securely authenticating clients. If you select the WPA Personal protocol (also
known as WPA pre-shared key or WPA-PSK) as the security method for any VAP,
you can use the WPA-PSK Complexity page to configure complexity requirements
for the key used in the authentication process. More complex keys provide
increased security.
To configure WPA-PSK complexity:
STEP 1 Select Security > WPA-PSK Complexity in the navigation pane.
STEP 2 Click Enable for the WPA-PSK Complexity setting to enable the WAP device to
check WPA-PSK keys against the criteria you configure. If you uncheck the box,
none of these settings are used. WPA-PSK Complexity is disabled by default.
STEP 3 Configure the parameters:
•
WPA-PSK Minimum Character Class—The minimum number of character
classes that must be represented in the key string. The four possible
character classes are uppercase letters, lowercase letters, numbers, and
special characters available on a standard keyboard. Three is the default.
•
WPA-PSK Different From Current—Select one of these options:
-
Enable—Users must configure a different key after their current key
expires.
-
Disable—Users can use the old or previous key after their current key
expires.
•
•
Maximum WPA-PSK Length—The maximum key length in number of
characters is from 32 to 63. The default is 63.
Minimum WPA-PSK Length—The minimum key length in number of
characters is from 8 to 16. The default is 8. Check the box to make the field
editable and to activate this requirement.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
115
7
Client Quality of Service
This chapter provides an overview of Client quality of service (QoS) and explains
the QoS features available from the Client QoS menu. It contains these topics:
•
•
•
•
•
•
Client QoS Global Settings
You can use the Client QoS Global Settings page to enable or disable quality of
service functionality on the WAP device.
If you disable Client QoS Mode, all ACLs, rate limiting, and DiffServ configurations
are globally disabled.
If you enable this mode, you can also enable or disable Client QoS mode on
page.
ACL
ACLs are a collection of permit and deny conditions, called rules, that provide
security by blocking unauthorized users and allowing authorized users to access
specific resources. ACLs can block any unwarranted attempts to reach network
resources.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
116
Client Quality of Service
ACL
7
The WAP device supports up to 50 IPv4, IPv6, and MAC ACLs.
IPv4 and IPv6 ACLs
IP ACLs classify traffic for Layers 3 and 4.
Each ACL is a set of up to 10 rules applied to traffic sent or received by the WAP
device. Each rule specifies whether the contents of a given field should be used to
permit or deny access to the network. Rules can be based on various criteria and
may apply to one or more fields within a packet, such as the source or destination
IP address, the source or destination port, or the protocol carried in the packet.
NOTE There is an implicit deny at the end of every rule created. To avoid deny all, it is
strongly recommended to add a permit rule within the ACL to allow traffic.
MAC ACLs
MAC ACLs are Layer 2 ACLs. You can configure the rules to inspect fields of a
frame such as the source or destination MAC address, the VLAN ID, or the class of
service. When a frame enters or exits the WAP device port (depending on whether
the ACL is applied in the up or down direction), the WAP device inspects the frame
and checks the ACL rules against the content of the frame. If any of the rules match
the content, a permit or deny action is taken on the frame.
Configuring ACLs
Configure ACLs and rules on the ACL Configuration page, and then apply the rules
to a specified VAP.
These steps give a general description of how to configure ACLs:
STEP 1 Select Client QoS > ACL in the navigation pane.
STEP 2 Specify a name for the ACL.
STEP 3 Select the type of ACL to add.
STEP 4 Add the ACL.
STEP 5 Add new rules to the ACL.
STEP 6 Configure the match criteria for the rules.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
117
Client Quality of Service
ACL
7
These steps give a detailed description of how to configure ACLs:
STEP 1 Select Client QoS > ACL in the navigation pane.
STEP 2 Enter these parameters to create a new ACL:
•
ACL Name—A name to identify the ACL. The name can contain from 1 to 31
alphanumeric and special characters. Spaces are not allowed.
•
ACL Type—The type of ACL to configure:
-
-
-
IPv4
IPv6
MAC
IPv4 and IPv6 ACLs control access to network resources based on Layer 3
and Layer 4 criteria. MAC ACLs control access based on Layer 2 criteria.
STEP 3 Click Add ACL.
The page shows additional fields for configuring the ACL.
STEP 4 Configure the rule parameters:
•
ACL Name - ACL Type—The ACL to configure with the new rule. The list
contains all ACLs added in the ACL Configuration section.
•
Rule—The action to be taken:
-
-
Select New Rule to configure a new rule for the selected ACL.
If rules already exist (even if created for use with other ACLs), you can
select the rule number to add the rule to the selected ACL or to modify
the rule.
When an ACL has multiple rules, the rules are applied to the packet or frame
in the order in which you add them to the ACL. There is an implicit deny all
rule as the final rule.
•
Action—Whether the ACL rule permits or denies an action.
When you select Permit, the rule allows all traffic that meets the rule criteria
to enter or exit the WAP device (depending on the ACL direction you select).
Traffic that does not meet the criteria is dropped.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
118
Client Quality of Service
ACL
7
When you select Deny, the rule blocks all traffic that meets the rule criteria
from entering or exiting the WAP device (depending on the ACL direction
you select). Traffic that does not meet the criteria is forwarded unless this
rule is the final rule. Because there is an implicit deny all rule at the end of
every ACL, traffic that is not explicitly permitted is dropped.
•
Match Every Packet—If selected, the rule, which either has a permit or deny
action, matches the frame or packet regardless of its contents.
If you select this field, you cannot configure any additional match criteria. The
Match Every Packet option is selected by default for a new rule. You must
clear the option to configure other match fields.
For IPv4 ACLs, configure these parameters:
•
Protocol—The Protocol field to use an Layer 3 or Layer 4 protocol match
condition based on the value of the IP Protocol field in IPv4 packets or the
Next Header field in IPv6 packets.
If you select Protocol, select one of these options:
-
Select From List—Select one of these protocols: IP, ICMP, IGMP, TCP, or
UDP.
-
Match to Value—Enter a standard IANA-assigned protocol ID from
0 to 255. Choose this method to identify a protocol not listed by name in
the Select From List.
•
•
Source IP Address—Requires a packet's source IP address to match the
address listed here. Enter an IP address in the appropriate field to apply this
criteria.
Wild Card Mask—The source IP address wildcard mask.
The wildcard mask determines which bits are used and which bits are
ignored. A wildcard mask of 255.255.255.255 indicates that no bit is
important. A wildcard of 0.0.0.0 indicates that all bits are important. This field
is required when Source IP Address is checked.
A wildcard mask is basically the inverse of a subnet mask. For example, to
match the criteria to a single host address, use a wildcard mask of 0.0.0.0. To
match the criteria to a 24-bit subnet (for example, 192.168.10.0/24), use a
wildcard mask of 0.0.0.255.
•
Source Port—Includes a source port in the match condition for the rule. The
source port is identified in the datagram header.
If you select Source Port, choose the port name or enter the port number.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
119
Client Quality of Service
ACL
7
-
-
Select From List—The keyword associated with the source port to
match: ftp, ftpdata, http, smtp, snmp, telnet, tftp, www.
Each of these keywords translates into its equivalent port number.
Match to Port—The IANA port number to match to the source port
identified in the datagram header. The port range is 0 to 65535 and
includes three different types of ports:
0 to 1023—Well Known Ports
1024 to 49151—Registered Ports
49152 to 65535—Dynamic and/or Private Ports
•
•
Destination IP Address—Requires a packet's destination IP address to
match the address listed here. Enter an IP address in the appropriate field to
apply this criteria.
Wild Card Mask—The destination IP address wildcard mask.
The wildcard mask determines which bits are used and which bits are
ignored. A wildcard mask of 255.255.255.255 indicates that no bit is
important. A wildcard of 0.0.0.0 indicates that all bits are important. This field
is required when Source IP Address is selected.
A wildcard mask is basically the inverse of a subnet mask. For example, to
match the criteria to a single host address, use a wildcard mask of 0.0.0.0. To
match the criteria to a 24-bit subnet (for example, 192.168.10.0/24), use a
wildcard mask of 0.0.0.255.
•
Destination Port—Includes a destination port in the match condition for the
rule. The destination port is identified in the datagram header.
If you select the Destination Port, choose the port name or enter the port
number.
-
-
Select From List—Select the keyword associated with the destination
port to match: ftp, ftpdata, http, smtp, snmp, telnet, tftp, www.
Each of these keywords translates into its equivalent port number.
Match to Port—The IANA port number to match to the destination port
identified in the datagram header. The port range is from 0 to 65535 and
includes three different types of ports:
0 to 1023—Well-Known Ports
1024 to 49151—Registered Ports
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
120
Client Quality of Service
ACL
7
49152 to 65535—Dynamic and/or Private Ports
•
IP DSCP—Matches packets based on their IP DSCP value.
If you select IP DSCP, choose one of these options as the match criteria:
-
Select From List—DSCP Assured Forwarding (AS), Class of Service
(CS), or Expedited Forwarding (EF) values.
-
Match to Value—A custom DSCP value, from 0 to 63.
•
•
IP Precedence—Matches packets based on their IP Precedence value. If
selected, enter an IP Precedence value from 0 to 7.
IP TOS Bits—Specifies a value to use the packet's Type of Service bits in
the IP header as match criteria.
The IP TOS field in a packet is defined as all eight bits of the Service Type
octet in the IP header. The IP TOS Bits value is a two-digit hexadecimal
number from 00 to ff.
The high-order three bits represent the IP precedence value. The high-order
six bits represent the IP Differentiated Services Code Point (DSCP) value.
•
IP TOS Mask—Enter an IP TOS Mask value to identify the bit positions in the
IP TOS Bits value that are used for comparison against the IP TOS field in a
packet.
The IP TOS Mask value is a two-digit hexadecimal number from 00 to FF,
representing an inverted (that is, wildcard) mask. The zero-valued bits in the
IP TOS Mask denote the bit positions in the IP TOS Bits value that are used
for comparison against the IP TOS field of a packet. For example, to check
for an IP TOS value having bits 7 and 5 set and bit 1 clear, where bit 7 is most
significant, use an IP TOS Bits value of 0 and an IP TOS Mask of 00.
For IPv6 ACLs, configure these parameters:
•
Protocol—Select the Protocol field to use a Layer 3 or Layer 4 protocol
match condition based on the value of the IP Protocol field in IPv4 packets or
the Next Header field in IPv6 packets.
If you select this field, choose the protocol to match by keyword or protocol
ID.
•
Source IPv6 Address—Select this field to require a packet's source IPv6
address to match the address listed here. Enter an IPv6 address in the
appropriate field to apply this criteria.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
121
Client Quality of Service
ACL
7
•
•
Source IPv6 Prefix Length—Enter the prefix length of the source IPv6
address.
Source Port—Select this option to include a source port in the match
condition for the rule. The source port is identified in the datagram header. If
selected, choose the port name or enter the port number.
•
Destination IPv6 Address—Select this field to require a packet's
destination IPv6 address to match the address listed here. Enter an IPv6
address in the appropriate field to apply this criteria.
•
•
Destination IPv6 Prefix Length—Enter the prefix length of the destination
IPv6 address.
Destination Port—Select this option to include a destination port in the
match condition for the rule. The destination port is identified in the datagram
header. If selected, choose the port name or enter the port number.
•
•
IPv6 Flow Label—A 20-bit number that is unique to an IPv6 packet. It is used
by end stations to signify QoS handling in routers (range 0 to 1048575).
IP DSCP—Matches packets based on their IP DSCP value. If selected,
choose one of these options as the match criteria:
-
Select From List—DSCP Assured Forwarding (AS), Class of Service
(CS), or Expedited Forwarding (EF) values.
-
Match to Value—A custom DSCP value, from 0 to 63.
For a MAC ACL, configure these parameters:
•
EtherType—Select to compare the match criteria against the value in the
header of an Ethernet frame.
Select an EtherType keyword or enter an EtherType value to specify the
match criteria.
-
Select from List—Select one of these protocol types: appletalk, arp,
ipv4, ipv6, ipx, netbios, pppoe.
-
Match to Value—Enter a custom protocol identifier to which packets are
matched. The value is a four-digit hexadecimal number in the range of
0600 to FFFF.
•
Class of Service—Select this field and enter an 802.1p user priority to
compare against an Ethernet frame.
The valid range is from 0 to 7. This field is located in the first/only 802.1Q
VLAN tag.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
122
Client Quality of Service
ACL
7
•
•
Source MAC Address—Select this field and enter the source MAC address
to compare against an Ethernet frame.
Source MAC Mask—Select this field and enter the source MAC address
mask specifying which bits in the source MAC to compare against an
Ethernet frame.
For each bit position in the MAC mask, a 0 indicates that the corresponding
address bit is significant and a 1 indicates that the address bit is ignored. For
example, to check only the first four octets of a MAC address, a MAC mask
of 00:00:00:00:ff:ff is used. A MAC mask of 00:00:00:00:00:00 checks all
address bits and is used to match a single MAC address.
•
•
Destination MAC Address—Select this field and enter the destination MAC
address to compare against an Ethernet frame.
Destination MAC Mask—Enter the destination MAC address mask to
specify which bits in the destination MAC to compare against an Ethernet
frame.
For each bit position in the MAC mask, a 0 indicates that the corresponding
address bit is significant and a 1 indicates that the address bit is ignored. For
example, to check only the first four octets of a MAC address, a MAC mask
of 00:00:00:00:ff:ff is used. A MAC mask of 00:00:00:00:00:00 checks all
address bits and is used to match a single MAC address.
•
VLAN ID—Select this field and enter the specific VLAN ID to compare
against an Ethernet frame.
This field is located in the first/only 802.1Q VLAN tag.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
NOTE To delete an ACL, ensure that it is selected in the ACL Name-ACL Type list, select
Delete ACL, and click Save.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
123
Client Quality of Service
Class Map
7
Class Map
The Client QoS feature contains Differentiated Services (DiffServ) support that
allows traffic to be classified into streams and given a certain QoS treatment in
accordance with defined per-hop behaviors.
Standard IP-based networks are designed to provide best-effort data delivery
service. Best-effort service implies that the network delivers the data in a timely
fashion, although there is no guarantee that it will. During times of congestion,
packets may be delayed, sent sporadically, or dropped. For typical Internet
applications, such as email and file transfer, a slight degradation in service is
acceptable and in many cases unnoticeable. However, on applications with strict
timing requirements, such as voice or multimedia, any degradation of service has
undesirable effects.
A DiffServ configuration begins with defining class maps, which classify traffic
according to their IP protocol and other criteria. Each class map can then be
associated with a policy map, which defines how to handle the traffic class.
Classes that include time-sensitive traffic can be assigned to policy maps that
give precedence over other traffic.
page to define policies and associate class maps to them.
Adding a Class Map
To add a class map:
STEP 1 Select Client QoS > Class Map in the navigation pane.
STEP 2 Enter a Class Map Name. The name can contain from 1 to 31 alphanumeric and
special characters. Spaces are not allowed.
STEP 3 Select a value from the Match Layer 3 Protocol list:
•
•
IPv4—The class map applies only to IPv4 traffic on the WAP device.
IPv6—The class map applies only to IPv6 traffic on the WAP device.
The Class Map page appears with additional fields, depending on the Layer 3
protocol selected:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
124
Client Quality of Service
Class Map
7
Use the fields in the Match Criteria Configuration area to match packets to a class.
Select the check box for each field to be used as a criterion for a class and enter
data in the related field. You can have multiple match criteria in a class.
The match criteria fields that are available depend on whether the class map is an
IPv4 or IPv6 class map.
Defining a Class Map
To configure a class map:
STEP 1 Select the class map from the Class Map Name list.
STEP 2 Configure the parameters (parameters that appear only for IPv4 or IPv6 class
maps are noted):
•
Match Every Packet—The match condition is true to all the parameters in a
Layer 3 packet.
When selected, all Layer 3 packets will match the condition.
•
Protocol—Use a Layer 3 or Layer 4 protocol match condition based on the
value of the IP Protocol field in IPv4 packets or the Next Header field in IPv6
packets.
If you select this field, choose the protocol to match by keyword or enter a
protocol ID.
-
Select From List—Match the selected protocol: IP, ICMP, IPv6, ICMPv6,
I G M P, TC P, U D P.
-
Match to Value—Match a protocol that is not listed by name. Enter the
protocol ID. The protocol ID is a standard value assigned by IANA. The
range is a number from 0 to 255.
•
•
Source IP Address or Source IPv6 Address—Requires a packet's source
IP address to match the address listed here. Check the box and enter an IP
address.
Source IP Mask (IPv4 only)—The source IP address mask.
The mask for DiffServ is a network-style bit mask in IP dotted decimal format
indicating which part(s) of the destination IP address to use for matching
against packet content.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
125
Client Quality of Service
Class Map
7
A DiffServ mask of 255.255.255.255 indicates that all bits are important, and
a mask of 0.0.0.0 indicates that no bits are important. The opposite is true
with an ACL wildcard mask. For example, to match the criteria to a single host
address, use a mask of 255.255.255.255. To match the criteria to a 24-bit
subnet (for example, 192.168.10.0/24), use a mask of 255.255.255.0.
•
•
Source IPv6 Prefix Length (IPv6 only)—The prefix length of the source IPv6
address.
Destination IP Address or Destination IPv6 Address—Requires a packet's
destination IP address to match the address listed here. Enter an IP address
in the appropriate field to apply this criteria.
•
Destination IP Mask (IPv4 only)—The destination IP address mask.
The mask for DiffServ is a network-style bit mask in IP dotted decimal format
indicating which part(s) of the destination IP address to use for matching
against packet content.
A DiffServ mask of 255.255.255.255 indicates that all bits are important, and
a mask of 0.0.0.0 indicates that no bits are important. The opposite is true
with an ACL wildcard mask. For example, to match the criteria to a single host
address, use a mask of 255.255.255.255. To match the criteria to a 24-bit
subnet (for example, 192.168.10.0/24), use a mask of 255.255.255.0.
•
•
Destination IPv6 Prefix Length (IPv6 only)—The prefix length of the
destination IPv6 address.
IPv6 Flow Label (IPv6 only)—A 20-bit number that is unique to an IPv6
packet. It is used by end stations to signify QoS handling in routers (range 0
to 1048575).
•
•
IP DSCP—See description under Service Type fields.
Source Port—Includes a source port in the match condition for the rule. The
source port is identified in the datagram header.
If you select the field, choose the port name or enter the port number.
-
Select From List—Matches a keyword associated with the source port:
ftp, ftpdata, http, smtp, snmp, telnet, tftp, www.
Each of these keywords translates into its equivalent port number.
-
Match to Port—Matches the source port number in the datagram header
to an IANA port number that you specify. The port range is from 0 to
65535 and includes three different types of ports:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
126
Client Quality of Service
Class Map
7
0 to 1023—Well-Known Ports
1024 to 49151—Registered Ports
49152 to 65535—Dynamic and/or Private Ports
•
Destination Port—Includes a destination port in the match condition for the
rule. The destination port is identified in the datagram header.
If you select this field, choose the port name or enter the port number.
-
-
Select From List—Matches the destination port in the datagram header
with the selected keyword: ftp, ftpdata, http, smtp, snmp, telnet, tftp,
www.
Each of these keywords translates into its equivalent port number.
Match to Port—Matches the destination port in the datagram header
with an IANA port number that you specify. The port range is from 0 to
65535 and includes three different types of ports:
0 to 1023—Well Known Ports
1024 to 49151—Registered Ports
49152 to 65535—Dynamic and/or Private Ports
•
EtherType—Compares the match criteria against the value in the header of
an Ethernet frame.
Select an EtherType keyword or enter an EtherType value to specify the
match criteria.
-
Select from List—Matches the Ethertype in the datagram header with
the selected protocol types: appletalk, arp, ipv4, ipv6, ipx, netbios,
pppoe.
-
Match to Value—Matches the Ethertype in the datagram header with a
custom protocol identifier that you specify. The value can be a four-digit
hexadecimal number in the range of 0600 to FFFF.
•
•
•
Class of Service—A class of service 802.1p user priority value to be
matched for the packets. The valid range is from 0 to 7.
Source MAC Address—A source MAC address to compare against an
Ethernet frame.
Source MAC Mask—The source MAC address mask specifying which bits
in the destination MAC to compare against an Ethernet frame.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
127
Client Quality of Service
Class Map
7
For each bit position in the MAC mask, a 0 indicates that the corresponding
address bit is significant and a 1 indicates that the address bit is ignored. For
example, to check only the first four octets of a MAC address, a MAC mask
of 00:00:00:00:ff:ff is used. A MAC mask of 00:00:00:00:00:00 checks all
address bits and is used to match a single MAC address.
•
•
Destination MAC Address—The destination MAC address to compare
against an Ethernet frame.
Destination MAC Mask—The destination MAC address mask specifying
which bits in the destination MAC to compare against an Ethernet frame.
For each bit position in the MAC mask, a 0 indicates that the corresponding
address bit is significant and a 1 indicates that the address bit is ignored. For
example, to check only the first four octets of a MAC address, a MAC mask
of 00:00:00:00:ff:ff is used. A MAC mask of 00:00:00:00:00:00 checks all
address bits and is used to match a single MAC address.
•
VLAN ID—A VLAN ID to be matched for packets. The VLAN ID range is
from 0 to 4095.
The following Service Type fields show for IPv4 only. You can specify one type
of service to use in matching packets to class criteria.
•
IP DSCP—A differentiated services code point (DSCP) value to use as a
match criterion:
-
-
Select from List—A list of DSCP types.
Match to Value—A DSCP value that you specify, from 0 to 63.
•
•
IP Precedence (IPv4 only)—Matches the packet's IP Precedence value to
the class criteria IP Precedence value. The IP Precedence range is from 0 to
7.
IP TOS Bits (IPv4 only)—Uses the packet's Type of Service bits in the IP
header as match criteria.
The IP TOS bit value ranges between (00 to FF). The high-order three bits
represent the IP Precedence value. The high-order six bits represent the IP
Differentiated Services Code Point (DSCP) value.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
NOTE To delete a class map, select it in the Class Map Name list and click Delete. The
class map cannot be deleted if it is already attached to a policy.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
128
Client Quality of Service
Policy Map
7
Policy Map
Packets are classified and processed based on defined criteria. The classification
a policy's attributes on the Policy Map page. Policy attributes may be defined on a
per-class instance basis and determine how traffic that matches the class criteria
is handled.
The WAP device supports up to 50 policy maps. A policy map can contain up to
10 class maps.
To add and configure a policy map:
STEP 1 Select Client QoS > Policy Map in the navigation pane.
STEP 2 Enter a Policy Map Name The name can contain from 1 to 31 alphanumeric and
special characters. Spaces are not allowed.
STEP 3 Click Add Policy Map. The page refreshes with additional fields for configuring
the policy map.
STEP 4 In the Policy Class Definition area, ensure that the newly created policy map
shows in the Policy Map Name list.
STEP 5 In the Class Map Name list, select the class map to apply this policy.
STEP 6 Configure the parameters:
•
Police Simple—Establishes the traffic policing style for the class. The
simple form of the policing style uses a single data rate and burst size,
resulting in two outcomes: conform and nonconform. If you select this field,
configure one of these fields:
-
Committed Rate—The committed rate, in Kbps, to which traffic must
conform. The range is from 1 to 1000000 Kbps.
-
Committed Burst—The committed burst size, in bytes, to which traffic
must conform. The range is from 1 to 204800000 bytes.
•
•
Send—Specifies that all packets for the associated traffic stream are to be
forwarded if the class map criteria is met.
Drop—Specifies that all packets for the associated traffic stream are to be
dropped if the class map criteria is met.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
129
Client Quality of Service
Client QoS Association
7
•
•
Mark Class of Service—Marks all packets for the associated traffic stream
with the specified class of service value in the priority field of the 802.1p
header. If the packet does not already contain this header, one is inserted.
The CoS value is an integer from 0 to 7.
Mark IP DSCP—Marks all packets for the associated traffic stream with the
IP DSCP value you select from the list or specify.
-
-
Select from List—A list of DSCP types.
Match to Value—A DSCP value that you specify. The value is an integer
between 0 to 63.
•
Mark IP Precedence—Marks all packets for the associated traffic stream
with the specified IP precedence value. The IP precedence value is an
integer from 0 to 7.
•
•
Disassociate Class Map—Removes the class selected in the Class Map
Name list from the policy selected in the Policy Map Name list.
Member Classes—Lists all DiffServ classes currently defined as members
of the selected policy. If no class is associated with the policy, the field is
empty.
STEP 7 Click Save. The changes are saved to the Startup Configuration.
NOTE To delete a policy map, select it in the Policy Map Name list and click Delete.
Client QoS Association
The Client QoS Association page provides additional control over certain QoS
aspects of wireless clients that connect to the network, such as the amount of
bandwidth an individual client is allowed to send and receive. To control general
categories of traffic, such as HTTP traffic or traffic from a specific subnet, you can
configure ACLs and assign them to one or more VAPs.
In addition to controlling general traffic categories, Client QoS allows you to
configure per-client conditioning of various micro-flows through Differentiated
Services (DiffServ). DiffServ policies are a useful tool for establishing general
micro-flow definition and treatment characteristics that can be applied to each
wireless client, both inbound and outbound, when it is authenticated on the
network.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
130
Client Quality of Service
Client QoS Association
7
To configure client QoS association parameters:
STEP 1 Select Client QoS > Client QoS Association in the navigation pane.
STEP 2 From the VAP list, select the VAP on which you want to configure client QoS
parameters.
STEP 3 Select Enable for the Client QoS Global to enable this feature.
STEP 4 Configure these parameters for the selected VAP:
•
Client QoS Mode—Select Enable to enable client QoS functionality on the
selected VAP.
•
Bandwidth Limit Down—The maximum allowed transmission rate from the
WAP device to the client in bits per second (bps). The valid range is from 0
to 300 Mbps.
•
•
Bandwidth Limit Up—The maximum allowed transmission rate from the
client to the WAP device in bits per second (bps). The valid range is from 0
to 300 Mbps.
ACL Type Down—The type of ACL to apply to traffic in the outbound (WAP
device-to-client) direction, which can be one of these options:
-
-
-
IPv4—The ACL examines IPv4 packets for matches to ACL rules.
IPv6—The ACL examines IPv6 packets for matches to ACL rules.
MAC—The ACL examines Layer 2 frames for matches to ACL rules.
•
•
ACL Name Down—The name of the ACL applied to traffic in the outbound
direction.
After switching the packet or frame to the outbound interface, the ACL's
rules are checked for a match. The packet or frame is transmitted if it is
permitted and discarded if it is denied.
ACL Type Up—The type of ACL that is applied to traffic in the inbound
(client-to-WAP) direction, which can be one of these options:
-
-
-
IPv4—The ACL examines IPv4 packets for matches to ACL rules.
IPv6—The ACL examines IPv6 packets for matches to ACL rules.
MAC—The ACL examines Layer 2 frames for matches to ACL rules.
•
ACL Name Up—The name of the ACL applied to traffic entering the WAP
device in the inbound direction.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
131
Client Quality of Service
Client QoS Status
7
When a packet or frame is received by the WAP device, the ACL's rules are
checked for a match. The packet or frame is processed if it is permitted and
discarded if it is denied.
•
•
DiffServ Policy Down—The name of the DiffServ policy applied to traffic
from the WAP device in the outbound (WAP-to-client) direction.
DiffServ Policy Up—The name of the DiffServ policy applied to traffic sent
to the WAP device in the inbound (client-to-WAP) direction.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
Client QoS Status
The Client QoS Status page shows the client QoS settings that are applied to each
client currently associated with the WAP device.
To show the Client QoS Status page, select Client QoS > Client QoS Status in the
navigation pane.
Use these fields to configure Client QoS Status:
•
Station—The Station menu contains the MAC address of each client
currently associated with the WAP device. To view the QoS settings
applied to a client, select its MAC address from the list.
•
•
•
Global QoS Mode—Whether QoS is enabled globally on the WAP device.
Client QoS Mode—Whether QoS is enabled on the associated VAP. This
Bandwidth Limit Down—The maximum allowed transmission rate from the
WAP device to the client in bits per second (bps). The valid range is from 0
to 4294967295 bps.
•
•
Bandwidth Limit Up—The maximum allowed transmission rate from the
client to the WAP device in bits per second (bps). The valid range is from 0
to 4294967295 bps.
ACL Type Up—The type of ACL that is applied to traffic in the inbound
(client-to-WAP) direction, which can be one of these options:
-
IPv4: The ACL examines IPv4 packets for matches to ACL rules.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
132
Client Quality of Service
Client QoS Status
7
-
-
IPv6: The ACL examines IPv6 packets for matches to ACL rules.
MAC: The ACL examines Layer 2 frames for matches to ACL rules.
•
•
ACL Name Up—The name of the ACL applied to traffic entering the WAP in
the inbound direction. When a packet or frame is received by the WAP, the
ACL rules are checked for a match. The packet or frame is processed if it is
permitted and discarded if it is denied.
ACL Type Down—The type of ACL to apply to traffic in the outbound
(WAP-to-client) direction, which can be one of these options:
-
-
-
IPv4: The ACL examines IPv4 packets for matches to ACL rules.
IPv6: The ACL examines IPv6 packets for matches to ACL rules.
MAC: The ACL examines Layer 2 frames for matches to ACL rules.
•
ACL Name Down—The name of the ACL applied to traffic in the outbound
direction. After switching the packet or frame to the outbound interface, the
ACL rules are checked for a match. The packet or frame is transmitted if it is
permitted and discarded if it is denied.
•
•
DiffServ Policy Up—The name of the DiffServ policy applied to traffic sent
to the WAP device in the inbound (client-to-WAP) direction.
DiffServ Policy Down—The name of the DiffServ policy applied to traffic
from the WAP device in the outbound (WAP-to-client) direction.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
133
8
Simple Network Management Protocol
This chapter describes how to configure the Simple Network Management
Protocol (SNMP) to perform configuration and statistics gathering tasks.
It contains these topics:
•
•
•
•
•
•
SNMP Overview
SNMP defines a standard for recording, storing, and sharing information about
network devices. SNMP facilitates network management, troubleshooting, and
maintenance.
The WAP device supports SNMP versions 1, 2, and 3. Unless specifically noted, all
configuration parameters apply to SNMPv1 and SNMPv2c only. Key components
of any SNMP-managed network are managed devices, SNMP agents, and a
management system. The agents store data about their devices in Management
Information Bases (MIBs) and return this data to the SNMP manager when
requested. Managed devices can be network nodes such as WAP devices,
routers, switches, bridges, hubs, servers, or printers.
The WAP device can function as an SNMP managed device for seamless
integration into network management systems.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
134
Simple Network Management Protocol
General SNMP Settings
8
General SNMP Settings
You can use the General page to enable SNMP and configure basic protocol
settings.
To configure general SNMP settings:
STEP 1 Select SNMP > General in the navigation pane.
STEP 2 Select Enabled for the SNMP setting. SNMP is disabled by default.
STEP 3 Specify a UDP Port for SNMP traffic.
By default, an SNMP agent listens only to requests from port 161. However, you
can configure this so that the agent listens to requests on a different port. The valid
range is from 1025 to 65535.
STEP 4 Configure the SNMPv2 settings:
•
•
•
Read-only Community—A read-only community name for SNMPv2
access. The valid range is 1 to 256 alphanumeric and special characters.
The community name acts as a simple authentication feature to restrict the
machines on the network that can request data to the SNMP agent. The
name functions as a password, and the request is assumed to be authentic
if the sender knows the password.
Read-write Community—A read-write community name to be used for
SNMP set requests. The valid range is from 1 to 256 alphanumeric and
special characters.
Setting a community name is similar to setting a password. Only requests
from the machines that identify themselves with this community name are
accepted.
Management Station—Determines which stations can access the WAP
device through SNMP. Select one of these options:
-
All—The set of stations that can access the WAP device through SNMP
is not restricted.
-
User Defined—The set of permitted SNMP requests is restricted to
those specified.
•
NMS, IPv4 Address/Name—The IPv4 IP address, DNS hostname, or subnet
of the network management system (NMS), or the set of machines that can
execute get and set requests to the managed devices.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
135
Simple Network Management Protocol
General SNMP Settings
8
A DNS hostname can consist of one or more labels, which are sets of up to
63 alphanumeric characters. If a hostname includes multiple labels, each is
separated by a period (.). The entire series of labels and periods can be up
to 253 characters long.
As with community names, this setting provides a level of security on SNMP
settings. The SNMP agent only accepts requests from the IP address,
hostname, or subnet specified here.
To specify a subnet, enter one or more subnetwork address ranges in the
form address/mask_length where address is an IP address and
mask_length is the number of mask bits. Both formats address/mask and
address/mask_length are supported. For example, if you enter a range of
192.168.1.0/24, this specifies a subnetwork with address 192.168.1.0 and a
subnet mask of 255.255.255.0.
The address range is used to specify the subnet of the designated NMS.
Only machines with IP addresses in this range are permitted to execute get,
and set requests on the managed device. Given the example above, the
machines with addresses from 192.168.1.1 through 192.168.1.254 can
execute SNMP commands on the device. (The address identified by suffix .0
in a subnetwork range is always reserved for the subnet address, and the
address identified by .255 in the range is always reserved for the broadcast
address.)
As another example, if you enter a range of 10.10.1.128/25, machines with IP
addresses from 10.10.1.129 through 10.10.1.254 can execute SNMP requests
on managed devices. In this example, 10.10.1.128 is the network address and
10.10.1.255 is the broadcast address. A total of 126 addresses would be
designated.
•
NMS IPv6 Address/Name—The IPv6 address, DNS hostname, or subnet of
the machines that can execute, get, and set requests to the managed
devices. The IPv6 address should be in a form similar to
xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx (2001:DB8::CAD5:7D91).
A hostname can consist of one or more labels, which are sets of up to 63
alphanumeric characters. If a hostname includes multiple labels, each is
separated by a period (.). The entire series of labels and periods can be up
to 253 characters long.
STEP 5 Configure the SNMPv2 trap settings:
Trap Community—A global community string associated with SNMP traps.
•
Traps sent from the device provide this string as a community name. The
valid range is from 1 to 60 alphanumeric and special characters.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
136
Simple Network Management Protocol
Views
8
•
Trap Destination Table—A list of up to three IP addresses or hostnames to
receive SNMP traps. Check the box and choose a Host IP Address Type
(IPv4 or IPv6) before adding the Hostname/IP Address.
An example of a DNS hostname is snmptraps.foo.com. Because SNMP traps
are sent randomly from the SNMP agent, it makes sense to specify where
exactly the traps should be sent. You can have a maximum of three DNS
hostnames. Ensure that you select the Enabled check box and select the
appropriate Host IP Address Type.
Also see the note about hostnames in the preceding step.
STEP 6 Click Save. The changes are saved to the Startup Configuration.
NOTE After new settings are saved, the corresponding processes may be stopped and
restarted. When this happens, the WAP device may lose connectivity. We
recommend that you change WAP device settings when a loss of connectivity will
least affect your wireless clients.
Views
An SNMP MIB view is a family of view subtrees in the MIB hierarchy. A view
subtree is identified by the pairing of an Object Identifier (OID) subtree value with a
bit string mask value. Each MIB view is defined by two sets of view subtrees,
included in or excluded from the MIB view. You can create MIB views to control the
OID range that SNMPv3 users can access.
The WAP device supports a maximum of 16 views.
These notes summarize some critical guidelines regarding SNMPv3 view
configuration. Please read all the notes before proceeding.
NOTE A MIB view called all is created by default in the system. This view contains all
management objects supported by the system.
NOTE By default, view-all and view-none SNMPv3 views are created on the WAP device.
These views cannot be deleted or modified.
To add and configure an SNMP view:
STEP 1 Select SNMP > Views in the navigation pane.
STEP 2 Click Add to create a new row in the SNMPv3 Views table.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
137
Simple Network Management Protocol
Groups
8
STEP 3 Check the box in the new row and click Edit:
•
•
•
View Name—Enter a name that identifies the MIB view. View names can
contain up to 32 alphanumeric characters.
Type—Choose whether to include or exclude the view subtree or family of
subtrees from the MIB view.
OID—Enter an OID string for the subtree to include or exclude from the view.
For example, the system subtree is specified by the OID string .1.3.6.1.2.1.1.
•
Mask—Enter an OID mask. The mask is 47 characters in length. The format
of the OID mask is xx.xx.xx (.)... or xx:xx:xx.... (:) and is 16 octets in length. Each
octet is two hexadecimal characters separated by either a period (.) or a
colon (:). Only hex characters are accepted in this field.
For example, OID mask FA.80 is 11111010.10000000.
A family mask is used to define a family of view subtrees. The family mask
indicates which subidentifiers of the associated family OID string are
significant to the family's definition. A family of view subtrees enables
efficient control access to one row in a table.
STEP 4 Click Save. The view is added to the SNMPv3 Views list and your changes are
saved to the Startup Configuration.
NOTE To remove a view, select the view in the list and click Delete.
Groups
SNMPv3 groups allow you to combine users into groups of different authorization
and access privileges. Each group is associated with one of three security levels:
•
•
•
noAuthNoPriv
authNoPriv
authPriv
Access to Management Information Bases (MIBs) for each group is controlled by
associating a MIB view to a group for read or write access, separately.
By default, the WAP device has two groups:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
138
Simple Network Management Protocol
Groups
8
•
•
RO—A read-only group using authentication and data encryption. Users in
this group use an MD5 key/password for authentication and a DES key/
password for encryption. Both the MD5 and DES key/passwords must be
defined. By default, users of this group have read access to the default all
MIB view.
RW—A read/write group using authentication and data encryption. Users in
this group use an MD5 key/password for authentication and a DES key/
password for encryption. Both the MD5 and DES key/passwords must be
defined. By default, users of this group have read and write access to the
default all MIB view.
NOTE The default groups RO and RW cannot be deleted.
NOTE The WAP device supports a maximum of eight groups.
To add and configure an SNMP group:
STEP 1 Select SNMP > Groups in the navigation pane.
STEP 2 Click Add to create a new row in the SNMPv3 Groups table.
STEP 3 Check the box for the new group and click Edit.
STEP 4 Configure the parameters:
•
Group Name—A name that identifies the group. The default group names
are RO and RW.
Group names can contain up to 32 alphanumeric characters.
•
Security Level—Sets the security level for the group, which can be one of
these options:
-
noAuthentication-noPrivacy—No authentication and no data
encryption (no security).
-
Authentication-noPrivacy—Authentication, but no data encryption.
With this security level, users send SNMP messages that use an MD5
key/password for authentication, but not a DES key/password for
encryption.
-
Authentication-Privacy—Authentication and data encryption. With this
security level, users send an MD5 key/password for authentication and a
DES key/password for encryption.
For groups that require authentication, encryption, or both, you must
define the MD5 and DES key/passwords on the SNMP Users page.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
139
Simple Network Management Protocol
Users
8
•
•
Write Views—The write access to MIBs for the group, which can be one of
these options:
-
-
write-all—The group can create, alter, and delete MIBs.
write-none—The group cannot create, alter, or delete MIBs.
Read Views—The read access to MIBs for the group:
-
-
view-all—The group is allowed to view and read all MIBs.
view-none—The group cannot view or read MIBs.
STEP 5 Click Save. The group is added to the SNMPv3 Groups list and your changes are
saved to the Startup Configuration.
NOTE To remove a group, select the group in the list and click Delete.
Users
You can use the SNMP Users page to define users, associate a security level to
each user, and configure security keys per-user.
Each user is mapped to an SNMPv3 group, either from the predefined or user-
defined groups, and, optionally, is configured for authentication and encryption.
For authentication, only the MD5 type is supported. For encryption, only the DES
type is supported. There are no default SNMPv3 users on the WAP device, and
you can add up to eight users.
To a d d S N M P u s e r s :
STEP 1 Select SNMP > Users in the navigation pane.
STEP 2 Click Add to create a new row in the SNMPv3 Users table.
STEP 3 Check the box in the new row and click Edit.
STEP 4 Configure the parameters:
•
User Name—A name that identifies the SNMPv3 user. User names can
contain up to 32 alphanumeric characters.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
140
Simple Network Management Protocol
Ta r g e t s
8
•
•
Group—The group that the user is mapped to. The default groups are
RWAuth, RWPriv, and RO. You can define additional groups on the SNMP
Groups page.
Authentication Type—The type of authentication to use on SNMPv3
requests from the user, which can be one of these options:
-
-
MD5—Require MD5 authentication on SNMP requests from the user.
None—SNMPv3 requests from this user require no authentication.
•
•
Authentication Pass Phrase—(If you specify MD5 as the Authentication
Type) A pass phrase to enable the SNMP agent to authenticate requests
sent by the user. The pass phrase must be between 8 and 32 characters in
length.
Encryption Type—The type of privacy to use on SNMP requests from the
user, which can be one of these options:
-
-
DES—Use DES encryption on SNMPv3 requests from the user.
None—SNMPv3 requests from this user require no privacy.
•
Encryption Pass Phrase—(If you specify DES as the privacy type) A pass
phrase to use to encrypt the SNMP requests. The pass phrase must be
between 8 and 32 characters in length.
STEP 5 Click Save. The user is added to the SNMPv3 Users list and your changes are
saved to the Startup Configuration.
NOTE To remove a user, select the user in the list and click Delete.
Targets
SNMPv3 targets send SNMP notifications using Inform messages to the SNMP
Manager. For SNMPv3 targets, only Informs are sent, not traps. For SNMP versions
1 and 2, traps are sent. Each target is defined with a target IP address, UDP port,
and SNMPv3 user name.
configuring SNMPv3 targets.
NOTE The WAP device supports a maximum of eight targets.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
141
Simple Network Management Protocol
Ta r g e t s
8
To a d d S N M P t a r g e t s :
STEP 1 Select SNMP > Targets in the navigation pane.
STEP 2 Click Add. A new row is created in the table.
STEP 3 Check the box in the new row and click Edit.
STEP 4 Configure the parameters:
•
IP Address—Enter the IPv4 address of the remote SNMP manager to
receive the target.
•
•
UDP Port—Enter the UDP port to use for sending SNMPv3 targets.
Users—Enter the name of the SNMP user to associate with the target. To
STEP 5 Click Save. The user is added to the SNMPv3 Targets list and your changes are
saved to the Startup Configuration.
NOTE To remove an SMMP target, select the user in the list and click Delete.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
142
9
Captive Portal
This chapter describes the Captive Portal (CP) feature, which allows you to block
wireless clients from accessing the network until user verification has been
established. You can configure CP verification to allow access for both guest and
authenticated users.
NOTE The Captive Portal feature is available only on the Cisco WAP321 device.
Authenticated users must be validated against a database of authorized Captive
Portal groups or users before access is granted. The database can be stored
locally on the WAP device or on a RADIUS server.
Captive Portal consists of two CP instances. Each instance can be configured
independently, with different verification methods for each VAP or SSID. Cisco
WAP321 devices operate concurrently with some VAPs configured for CP
authentication and other VAPs configured for normal wireless authentication
methods, such as WPA or WPA Enterprise.
This chapter includes these topics:
•
•
•
•
•
•
•
•
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
143
Captive Portal
Captive Portal Global Configuration
9
Captive Portal Global Configuration
You can use the Global CP Configuration page to control the administrative state
of the CP feature and configure global settings that affect all captive portal
instances configured on the WAP device.
To configure CP Global settings:
STEP 1 Select Captive Portal > Global Configuration in the navigation pane.
STEP 2 Configure the parameters:
•
•
Captive Portal Mode—Enables CP operation on the WAP device.
Authentication Timeout—To access the network through a portal, the client
must first enter authentication information on an authentication web page.
This field specifies the number of seconds the WAP device keeps an
authentication session open with the associated wireless client. If the client
fails to enter authentication credentials within the timeout period allowed,
the client may need to refresh the web authentication page. The default
authentication timeout is 300 seconds. The range is from 60 to 600 seconds.
•
•
Additional HTTP Port—HTTP traffic uses the HTTP management port,
which is 80 by default. You can configure an additional port for HTTP traffic.
Enter a port number between 1025 and 65535, or 80. The HTTP and HTTPs
ports cannot be the same.
Additional HTTPS Port—HTTP traffic over SSL (HTTPS) uses the HTTPS
management port, which is 443 by default. You can configure an additional
port for HTTPS traffic. Enter port number between 1025 and 65535, or 443.
The HTTP and HTTPs ports cannot be the same.
The Captive Portal Configuration Counters area shows read-only CP information:
•
Instance Count—The number of CP instances currently configured on the
WAP device. Up to two instances can be configured.
•
Group Count—The number of CP groups currently configured on the WAP
device. Up to two groups can be configured. Default Group exists by default
and cannot be deleted.
•
User Count—The number of CP users currently configured on the WAP
device. Up to 128 users can be configured.
STEP 3 Click Save. The changes are saved to the Startup Configuration.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
144
Captive Portal
Instance Configuration
9
Instance Configuration
You can create up to two Captive Portal instances; each CP instance is a defined
set of instance parameters. Instances can be associated with one or more VAPs.
Different instances can be configured to respond differently to users as they
attempt to access the associated VAP.
NOTE Before you create an instance, review these bullets first:
•
•
•
To create a CP instance and configure its settings:
STEP 1 Select Captive Portal > Instance Configuration in the navigation pane.
STEP 2 Ensure that Create is selected from the Captive Port Instances list.
STEP 3 Enter an Instance Name from 1 to 32 alphanumeric characters and click Save.
STEP 4 Select the instance name from the Captive Port Instances list.
The Captive Portal Instance Parameters fields reappear with additional options.
STEP 5 Configure the parameters:
•
•
•
Instance ID—The instance ID. This field is nonconfigurable.
Administrative Mode—Enables and disables the CP instance.
Protocol—Specifies HTTP or HTTPs as the protocol for the CP instance to
use during the verification process.
-
-
HTTP—Does not use encryption during verification.
HTTPS—Uses the Secure Sockets Layer (SSL), which requires a
certificate to provide encryption.
The certificate is presented to the user at connection time.
•
Verification—The authentication method for CP to use to verify clients:
-
-
Guest—The user does not need to be authenticated by a database.
Local—The WAP device uses a local database to authenticated users.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
145
Captive Portal
Instance Configuration
9
-
RADIUS—The WAP device uses a database on a remote RADIUS server
to authenticate users.
•
•
•
Redirect—Specifies that CP should redirect the newly authenticated client
to the configured URL. If this option is clear, the user sees the locale-specific
welcome page after a successful verification.
Redirect URL—Enter the URL (including http://) to which the newly
authenticated client is redirected if the URL Redirect Mode is enabled. The
range is from 0 to 256 characters.
Away Timeout—The amount of time a user remains in the CP authenticated
client list after the client disassociates from the WAP. If the time specified in
this field expires before the client attempts to reauthenticate, the client entry
is removed from the authenticated client list. The range is from 0 to 1440
minutes. The default value is 60 minutes.
Users page. The away timeout value set on the Local Users page has
precedence over the value configured here, unless the value is set to 0 (the
default). A value of 0 indicates to use the instance timeout value.
•
•
Session Timeout—The time remaining, in seconds, for the CP session to be
valid. After the time reaches zero, the client is deauthenticated. The range is
from 0 to 1440 minutes. The default value is 0.
Maximum Bandwidth Upstream—The maximum upload speed, in
megabits per second, that a client can transmit traffic when using the captive
portal. This setting limits the bandwidth at which the client can send data into
the network. The range is from 0 to 300 Mbps. The default value is 0.
•
Maximum Bandwidth Downstream—The maximum download speed, in
megabits per second, that a client can receive traffic when using the captive
portal. This setting limits the bandwidth at which the client can receive data
from the network. The range is from 0 to 300 Mbps. The default value is 0.
•
•
User Group Name—If the Verification Mode is Local or RADIUS, assigns an
existing User Group to the CP instance. All users who belong to the group are
permitted to access the network through this portal.
RADIUS IP Network—Choose if the WAP RADIUS client uses the
configured IPv4 or IPv6 RADIUS server addresses.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
146
Captive Portal
Instance Configuration
9
•
•
Global RADIUS—If the Verification Mode is RADIUS, select this option to the
default Global RADIUS server list to authenticate clients. (See RADIUS
Server for information about configuring the global RADIUS servers.) If you
want the CP feature to use a different set of RADIUS servers, uncheck the
box and configure the servers in the fields on this page.
RADIUS Accounting—Enables tracking and measuring the resources a
particular user has consumed, such as system time and amount of data
transmitted and received.
If you enable RADIUS accounting, it is enabled for the primary RADIUS
server, all backup servers, and globally or locally configured servers.
•
Server IP Address 1 or Server IPv6 Address 1—The IPv4 or IPv6 address
for the primary RADIUS server for this VAP. The IPv4 address should be in a
form similar to xxx.xxx.xxx.xxx (192.0.2.10). The IPv6 address should be in a
form similar to xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx:xxxx
(2001:DB8::CAD5:7D91).
When the first wireless client tries to authenticate with a VAP, the WAP
device sends an authentication request to the primary server. If the primary
server responds to the authentication request, the WAP device continues to
use this RADIUS server as the primary server, and authentication requests
are sent to the specified address.
•
•
Server IP Address (2 through 4) or Server IPv6 Address (2 through 4)—
Up to three IPv4 or IPv6 backup RADIUS server addresses.
If authentication fails with the primary server, each configured backup server
is tried in sequence.
Key 1—The shared secret key that the WAP device uses to authenticate to
the primary RADIUS server.
You can use up to 63 standard alphanumeric and special characters. The key
is case sensitive and must match the key configured on the RADIUS server.
The text you enter is shown as asterisks.
•
•
•
Key 2 to 4—The RADIUS key associated with the configured backup
RADIUS servers. The server at Server IP Address 1 uses Key 1, Server IP
Address 2 uses Key 2, and so on.
Locale Count—The number of locales associated with the instance. You can
create and assign up to three different locales to each CP instance from the
Web Customization page.
Delete Instance—Deletes the current instance.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
147
Captive Portal
Instance Association
9
STEP 6 Click Save. Your changes are saved to the Startup Configuration.
Instance Association
Once you create an instance, you can use the Instance Association page to
associate a CP instance to a VAP. The associated CP instance settings applies to
users who attempt to authenticate on the VAP.
To associate an instance to a VAP:
STEP 1 Select Captive Portal > Instance Association in the navigation pane.
STEP 2 Select the instance name for each VAP you want to associate an instance to.
STEP 3 Click Save. Your change are saved to the Startup Configuration.
Web Portal Customization
Once your CP instance is associated with a VAP, you need to create a locale (an
authentication web page) and map it to the CP instance. When a user accesses a
VAP that is associated with a captive portal instance, the user sees an
authentication page. You use the Web Portal Customization page to create unique
pages for different locales on your network, and to customize the text and images
on the pages.
To create and customize a CP authentication page:
STEP 1 Select Captive Portal > Web Portal Customization in the navigation pane.
STEP 2 Select Create from the Captive Portal Web Locale list.
You can create up to three different authentication pages with different locales on
your network.
STEP 3 Enter a Web Locale Name to assign to the page. The name can be from 1 to 32
alphanumeric characters.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
148
Captive Portal
Web Portal Customization
9
STEP 4 From the Captive Portal Instances list, select the CP instance that this locale is
associated with.
You can associate multiple locales with an instance. When a user attempts to
access a particular VAP that is associated with a CP instance, the locales that are
associated with that instance show as links on the authentication page. The user
can select a link to switch to that locale.
STEP 5 Click Save. The changes are saved to the Startup Configuration.
STEP 6 From the Captive Portal Web Locale list, select the locale you created.
The page shows additional fields for modifying the locale. The Locale ID and
Instance Name fields cannot be edited. The editable fields are populated with
default values.
STEP 7 Configure the parameters:
•
•
Background Image Name—The image to show as the page background.
You can click Upload/Delete Custom Image to upload images for Captive
Portal instances. See Uploading and Deleting Images.
Logo Image Name—The image file to show on the top left corner of the
page. This image is used for branding purposes, such as the company logo.
If you uploaded a custom logo image to the WAP device, you can select it
from the list.
•
•
•
Foreground color—The HTML code for the foreground color in 6-digit
hexadecimal format. The range is from 1 to 32 characters. The default is
#999999.
Background color—The HTML code for the background color in 6-digit
hexadecimal format. The range is from 1 to 32 characters. The default is
#BFBFBF.
Separator—The HTML code for the color of the thick horizontal line that
separates the page header from the page body, in 6-digit hexadecimal
format. The range is from 1 to 32 characters. The default is #BFBFBF.
•
•
•
Locale Label—A descriptive label for the locale, from 1 to 32 characters.
The default is English.
Locale—An abbreviation for the locale, from 1 to 32 characters. The default
is en.
Account Image—The image file to show above the login field to depict an
authenticated login.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
149
Captive Portal
Web Portal Customization
9
•
•
•
•
Account Label—The text that instructs the user to enter a user name. The
range is from 1 to 32 characters.
User Label—The label for the user name text box. The range is from 1 to 32
characters.
Password Label—The label for the user password text box. The range is
from 1 to 64 characters.
Button Label—The label on the button that users click to submit their user
name/password for authentication. The range is from 2 to 32 characters. The
default is Connect.
•
Fonts—The name of the font to use for all text on the CP page. You can enter
multiple font names, each separated by a comma. If the first font is not
available on the client system, the next font is used, and so on. For font names
that have spaces, surround the entire name in quotes. The range is from 1 to
512 characters. The default is MS UI Gothic, Arial, sans-serif.
•
•
Browser Title—The text to show in the browser title bar. The range is from 1
to 128 characters. The default is Captive Portal.
Browser Content—The text that shows in the page header, to the right of the
logo. The range is from 1 to 128 characters. The default is Welcome to the
Wireless Network.
•
Content—The instructive text that shows in the page body below the user
name and password text boxes. The range is from 1 to 256 characters. The
default is To start using this service, enter your credentials and click the
connect button.
•
•
Acceptance Use Policy—The text that appears in the Acceptance Use
Policy box. The range is from 1 to 4096 characters. The default is
Acceptance Use Policy.
Accept Label—The text that instructs users to select the check box to
acknowledge reading and accepting the Acceptance Use Policy. The range
is from 1 to 128 characters. The default is Check here to indicate that you
have read and accepted the Acceptance Use Policy.
•
No Accept Text—The text that shows in a pop-up window when a user
submits login credentials without selecting the Acceptance Use Policy
check box. The range is from 1 to 128 characters. The default is Error: You
must acknowledge the Acceptance Use Policy before connecting!
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
150
Captive Portal
Web Portal Customization
9
•
•
•
•
•
Work In Progress Text—The text that shows during authentication. The
range is from 1 to 128 characters. The default is Connecting, please be
patient....
Denied Text—The text that shows when a user fails authentication. The
range is from 1 to 128 characters. The default is Error Invalid Credentials,
please try again!
Welcome Title—The text that shows when the client has authenticated to
the VAP. The range is from 1 to 128 characters. The default is
Congratulations!
Welcome Content—The text that shows when the client has connected to
the network. The range is from 1 to 256 characters. The default is You are
now authorized and connected to the network.
Delete Locale—Deletes the current locale.
STEP 8 Click Save. Your changes are saved to the Startup Configuration.
STEP 9 Click Preview to view the updated page.
NOTE You can click Preview to show the text and images that have already been saved
to the Startup Configuration. If you make a change, click Save before clicking
Preview to see your changes.
Uploading and Deleting Images
When users initiate access to a VAP that is associated with a captive portal
instance, an authentication page appears. You can customize the authentication
page with your own logo or other images.
Up to 18 images can be uploaded (assuming six locales, with each locale having
three images). All images must be 5 kilobytes or smaller and must be in GIF or JPG
format.
Images are resized to fit the specified dimensions. For best results, your logo and
account images should be similar in proportion to the default images, as follows:
Image Type
Use
Default Width by
Height
Background
Shows as the page background.
10 by 800 pixels
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
151
Captive Portal
Local Groups
9
Image Type
Logo
Use
Default Width by
Height
Shows at top left of page to provide
branding information.
168 by 78 pixels
Account
Shows above the login field to depict
an authenticated login.
295 by 55 pixels
To upload binary graphic files to the WAP device:
STEP 1 On the Web Portal Customization page, click Upload/Delete Custom Image next
to the Background Image Name, Logo Image Name, or Account Image fields.
The Web Portal Custom Image page appears.
STEP 2 Browse to select the image.
STEP 3 Click Upload.
STEP 4 Click Back to return to the Web Portal Custom Image page.
STEP 5 Select the Captive Portal Web Locale you want to configure.
STEP 6 For the Background Image Name, Logo Image Name, or Account Image fields,
select the newly uploaded image.
STEP 7 Click Save.
NOTE To delete an image, on the Web Portal Custom Image page, select it from the Delete
Web Customization Image list and click Delete. You cannot delete the default
images.
Local Groups
Each local user is assigned to a user group. Each group is assigned to a CP
instance. The group facilitates managing the assignment of users to CP instances.
The user group named Default is built-in and cannot be deleted. You can create up
to two additional user groups.
To add local user groups:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
152
Captive Portal
Local Users
9
STEP 1 Select Captive Portal > Local Groups in the navigation pane.
STEP 2 Enter a Group Name and click Save. The changes are saved to the Startup
Configuration.
NOTE To delete a group, select it in the Captive Portal Groups list, select the Delete
Group check box, and click Save.
Local Users
You can configure a captive portal instance to accommodate either guest users
and authorized users. Guest users do not have assigned user names and
passwords.
Authorized users provide a valid user name and password that must first be
validated against a local database or RADIUS server. Authorized users are
typically assigned to a CP instance that is associated with a different VAP than
guest users.
You can use the Local Users page to configure up to 128 authorized users in the
local database.
To add and configure a local user:
STEP 1 Select Captive Portal > Local Users in the navigation pane.
STEP 2 Enter a User Name and click Save.
Additional fields appear to configure the user.
STEP 3 Enter the parameters:
•
User Password—Enter the password, from 8 to 64 alphanumeric and
special characters. A user enter must enter the password to log into the
network through the Captive Portal.
•
•
Show Password as Clear Text—When enabled, the text you type is visible.
When disabled, the text is not masked as you enter it.
Away Timeout—The period of time a user remains in the CP authenticated
client list after the client disassociates from the AP. If the time specified in this
field expires before the client attempts to reauthenticate, the client entry is
removed from the authenticated client list. The range is from 0 to 1440
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
153
Captive Portal
Authenticated Clients
9
minutes. The default value is 60. The timeout value configured here has
precedence over the value configured for the captive portal instance, unless
the user value is set to 0. When set to 0, the timeout value configured for the
CP instance is used.
•
•
Group Name—The assigned user group. Each CP instance is configured to
support a particular group of users.
Maximum Bandwidth Up—The maximum upload speed, in megabits per
second, that a client can transmit traffic when using the captive portal. This
setting limits the bandwidth used to send data into the network. The range
is from 0 to 300 Mbps. The default is 0.
•
Maximum Bandwidth Down—The maximum download speed, in megabits
per second, that a client can receive traffic when using the captive portal.
This setting limits the bandwidth used to receive data from the network. The
range is from 0 to 300 Mbps. The default is 0.
•
Delete User—Deletes the current user.
STEP 4 Click Save. The changes are saved to the Startup Configuration.
Authenticated Clients
The Authenticated Clients page provides information about clients that have
authenticated on any Captive Portal instance.
To view the list of authenticated clients, select Captive Portal > Authenticated
Clients in the navigation pane.
•
•
•
•
MAC Address—The MAC address of the client.
IP Address—The IP address of the client.
User Name—The Captive Portal user name of the client.
Protocol—The protocol the user used to establish the connection (HTTP or
HTTPS).
•
Verification—The method used to authenticate the user on the Captive
Portal, which can be one of these values:
-
Guest—The user does not need to be authenticated by a database.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
154
Captive Portal
Failed Authentication Clients
9
-
-
Local—The WAP device uses a local database to authenticated users.
RADIUS—The WAP device uses a database on a remote RADIUS
server to authenticate users.
•
•
VAP ID—The VAP that the user is associated with.
Radio ID—The ID of the radio. Because the WAP321 has a single radio, this
field always shows Radio1.
•
•
•
Captive Portal ID—The ID of the Captive Portal instance to which the user
is associated.
Session Timeout—The time remaining, in seconds, for the CP session to be
valid. After the time reaches zero, the client is deauthenticated.
Away Timeout—The time remaining, in seconds, for the client entry to be
valid. The timer starts when the client dissociates from the CP. After the time
reaches zero, the client is deauthenticated.
•
•
•
•
Received Packets—The number of IP packets received by the WAP device
from the user station.
Transmitted Packets—The number of IP packets transmitted from the
WAP device to the user station.
Received Bytes—The number of bytes received by the WAP device from
the user station.
Transmitted Bytes—The number of bytes transmitted from the WAP
device to the user station.
You can click Refresh to show the latest data from the WAP device.
Failed Authentication Clients
The Failed Authenticated Clients page lists information about clients that
attempted to authenticate on a Captive Portal and failed.
To view a list of clients who failed authentication, select Captive Portal > Failed
Authentication Clients in the navigation pane.
•
•
•
MAC Address—The MAC address of the client.
IP Address—The IP address of the client.
User Name—The Captive Portal user name of the client.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
155
Captive Portal
Failed Authentication Clients
9
•
Verification—The method the client attempted to use to authenticate on the
Captive Portal, which can be one of these values:
-
-
-
Guest—The user does not need to be authenticated by a database.
Local—The WAP device uses a local database to authenticated users.
RADIUS—The WAP device uses a database on a remote RADIUS
server to authenticate users.
•
•
VAP ID—The VAP that the user is associated with.
Radio ID—The ID of the radio. Because the WAP321 has a single radio, this
field shows Radio1.
•
•
Captive Portal ID—The ID of the Captive Portal instance to which the user
is associated.
Failure Time—The time that the authentication failure occurred. A
timestamp is included that shows the time of the failure.
You can click Refresh to show the latest data from the WAP device.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
156
10
Single Point Setup
This chapter describes how to configure Single Point Setup over multiple WAP
devices.
It includes these topics:
•
•
•
•
•
Single Point Setup Overview
The Cisco WAP121 and WAP321 devices support Single Point Setup. Single Point
Setup provides a centralized method to administer and control wireless services
across multiple devices. You use Single Point Setup to create a single group, or
cluster, of wireless devices. After the WAP devices are clustered, you can view,
deploy, configure, and secure the wireless network as a single entity. After a
wireless cluster is created, Single Point Setup also facilitates channel planning
across your wireless services to reduce radio interference and maximize
bandwidth on the wireless network.
When you first set up your WAP device, you can use the Setup Wizard to configure
Single Point Setup or join an existing Single Point Setup. If you prefer not to use the
Setup Wizard, you can use the web-based configuration utility.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
157
Single Point Setup
Single Point Setup Overview
10
Managing Single Point Setup Across WAP Devices
Single Point Setup creates a dynamic, configuration-aware cluster, or group, of
WAP devices in the same subnet of a network. A cluster supports only a group of
configured WAP121 devices or a group of configured WAP321 devices. A single
cluster does not support a mix of WAP121 and WAP321 devices in the same
group.
Single Point Setup allows the management of more than one cluster in the same
subnet or network; however, they are managed as single independent entities.
The table below shows Single Point Setup wireless service limits.
Group/Cluster
Type
WAP Devices
per Single Point
Setup
Number of
Active Clients
per Single Point
Setup
Maximum
Number of
Clients (Active
and Idle)
WAP121
WAP321
4
8
40
64
160
256
A cluster can propagate configuration information, such as VAP settings, QoS
queue parameters, and radio parameters. When you configure Single Point Setup
on a device, settings from that device (whether they are manually set or set by
default) are propagated to other devices as they join the cluster. To form a cluster,
make sure the following prerequisites or conditions are met:
STEP 1 Plan your Single Point Setup cluster. Be sure the two or more WAP devices you
want to cluster are the same model. For example, Cisco WAP121 devices can only
cluster with other Cisco WAP121 devices.
It is strongly recommended to run the latest firmware version on all clustered WAP
devices.
NOTE Firmware upgrades are not propagated to all WAP devices in a
cluster; you must upgrade each device independently.
STEP 2 Set up the WAP devices that will be clustered on the same IP subnet and verify
that they are interconnected and accessible across the switched LAN network.
STEP 4 Verify that the WAP devices all reference the same Single Point Setup name. See
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
158
Single Point Setup
Single Point Setup Overview
10
Single Point Setup Negotiation
When a WAP device is enabled and configured for Single Point Setup, it begins
sending periodic advertisements every 10 seconds to announce its presence. If
there are other WAP devices that match the criteria for the cluster, arbitration
begins to determine which WAP device will distribute the master configuration to
the rest of the members of the cluster.
The following rules apply to Single Point Setup cluster formation and arbitration:
•
For existing Single Point Setup clusters, whenever the administrator
updates the configuration of any member of the cluster, the configuration
change is propagated to all members of the cluster, and the configured
WAP device assumes control of the cluster.
•
•
When two separate Single Point Setup clusters join into a single cluster,
then the latest modified cluster wins arbitration of the configuration and
overwrites and updates the configuration of all clustered WAP devices.
If a WAP device in a cluster does not receive advertisements from a WAP
device for more than 60 seconds (for example, if the device loses
connectivity to other devices in the cluster), the device is removed from the
cluster.
•
•
If a WAP device in Single Point Setup mode loses connectivity, it is not
immediately dropped from the cluster. If it regains connectivity and rejoins
the cluster without having been dropped, and configuration changes were
made to that device during the lost connectivity period, the changes are
propagated to the other cluster members when connectivity resumes.
If a WAP device in a cluster loses connectivity, is dropped, later rejoins the
cluster, and configuration changes were made in the during the lost
connectivity period, the changes are propagated to the device when it
rejoins. If there are configuration changes in both the disconnected device
and the cluster, then the device with the greatest number of changes and,
secondarily, the most recent change, will be selected to propagate its
configuration to the cluster. (That is, if WAP1 has more changes, but WAP2
has the most recent change, WAP1 is selected. If they have an equal
number of changes, but WAP2 has the most recent change, then WAP2 is
selected.)
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
159
Single Point Setup
Single Point Setup Overview
10
Operation of a WAP Device Dropped From a Single Point
Setup
When a WAP device that was previously a member of a cluster becomes
disconnected from the cluster, the following guidelines apply:
•
Loss of contact with the cluster prevents the WAP device from receiving the
latest operational configuration settings. The disconnection results in a halt
to proper seamless wireless service across the production network.
•
•
The WAP device continues to function with the wireless parameters that it
last received from the cluster.
Wireless clients associated with the non-clustered WAP device continue to
associate with the device with no interruption of the wireless connection. In
other words, loss of contact with the cluster does not necessarily prevent
wireless clients associated with that WAP device from continued access to
network resources.
•
If the loss of contact with the cluster is due to a physical or logical
disconnect with the LAN infrastructure, network services out to the wireless
clients may be impacted depending on the nature of the failure.
Propagation of Configuration Settings and Parameters in
Single Point Setup
The tables summarize configurations that are shared and propagated among all
clustered WAP devices.
Common Configuration Settings and Parameters that are Propagated in
Single Point Setup
Captive Portal
Client QoS
Password Complexity
User Accounts
QoS
Email Alert
HTTP/HTTPs Service (Except SSL Certificate Radio Settings Including
Configuration)
Log Settings
TSpec Settings (Some
exceptions)
Rogue AP Detection
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
160
Single Point Setup
Single Point Setup Overview
10
Common Configuration Settings and Parameters that are Propagated in
Single Point Setup
MAC Filtering
Scheduler
Management Access Control
Networks
SNMP General and SNMPv3
WPA-PSK Complexity
Time Settings
Radio Configuration Settings and Parameters that are Propagated in Single
Point Setup
Mode
Fragmentation Threshold
RTS Threshold
Rate Sets
Primary Channel
Protection
Fixed Multicast Rate
Broadcast or Multicast Rate Limiting
Channel Bandwidth
Short Guard Interval Supported
Radio Configuration Settings and Parameters that are Not Propagated in
Single Point Setup
Channel
Beacon Interval
DTIM Period
Maximum Stations
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
161
Single Point Setup
Access Points
10
Radio Configuration Settings and Parameters that are Not Propagated in
Single Point Setup
Transmit Power
Other Configuration Settings and Parameters That Are Not Propagated in
Single Point Setup
Bandwidth Utilization
Bonjour
Port Settings
VLAN and IPv4
WDS Bridge
WPS
IPv6 Address
IPv6 Tunnel
Packet Capture
WorkGroup Bridge
Access Points
The Access Points page allows you to enable or disable Single Point Setup on a
WAP device, view the cluster members, and configure the location and cluster
name for a member. You can also click the IP address of a member to configure
and view data on that device.
Configuring the WAP Device for Single Point Setup
To configure the location and name of an individual Single Point Setup cluster
member:
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
162
Single Point Setup
Access Points
10
STEP 1 Select Single Point Setup > Access Points in the navigation pane.
Single Point Setup is disabled by default on the WAP device. When disabled, the
Enable Single Point Setup button is visible. If Single Point Setup is enabled, the
Disable Single Point Setup button is visible. You can edit Single Point Setup
options only when Single Point Setup is disabled.
Icons on the right side of the page indicate whether Single Point Setup is enabled
and, if it is, the number of WAP devices that are currently joined in the cluster.
STEP 2 With Single Point Setup disabled, configure the following information for each
individual member of a Single Point Setup cluster.
•
Location—Enter a description of where the access point is physically
located, for example, Reception. The location field is optional.
•
Cluster Name—Enter the name of the cluster for the WAP device to join, for
example Reception_Cluster.
The cluster name is not sent to other WAP devices. You must configure the
same name on each device that is a member. The cluster name must be
unique for each Single Point Setup you configure on the network. The default
is ciscosb-cluster.
•
Clustering IP Version—Specify the IP version that the WAP devices in the
cluster use to communicate with other members of the cluster. The default is
IPv4.
If you choose IPv6, Single Point Setup can use the link local address,
autoconfigured IPv6 global address, and statically configured IPv6 global
address. Ensure that when using IPv6, all the WAP devices in the cluster
either use link-local addresses only or use global addresses only.
Single Point Setup works only with devices using the same type of IP
addressing. It does not work with a group of WAP devices where some have
IPv4 addresses and some have IPv6 addresses.
STEP 3 Click Enable Single Point Setup.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
163
Single Point Setup
Access Points
10
The WAP device begins searching for other WAP devices in the subnet that are
configured with the same cluster name and IP version. A potential cluster member
sends advertisements every 10 seconds to announce its presence.
While searching for other cluster members, the status indicates that the
configuration is being applied. Refresh the page to see the new configuration.
If one or more WAP devices are already configured with the same cluster settings,
the WAP device joins the cluster and information on each member shows in a
table.
STEP 4 Repeat these steps on additional WAP devices that you want to join the Single
Point Setup.
Viewing Single Point Setup Information
When Single Point Setup is enabled, the WAP device automatically forms a cluster
with other WAP devices with the same configuration. On the Access Points page,
the WAP devices detected are listed in a table and the following information is
shown:
•
•
Location—Description of where the access point is physically located.
MAC Address—Media Access Control (MAC) address of the access point.
The address is the MAC address for the bridge (br0), and is the address by
which the WAP device is known externally to other networks.
•
IP Address—The IP address for the access point.
Note that the Single Point Setup status and the number of WAP devices are shown
graphically on the right side of the page.
Adding a New Access Point to a Single Point Setup Cluster
To add a new access point that is currently in standalone mode into a Single Point
Setup cluster:
STEP 1 Go to the web-based configuration utility on the standalone access point.
STEP 2 Select Single Point Setup > Access Points in the navigation pane.
STEP 3 Set the Cluster name to the same name that is configured for the cluster
members.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
164
Single Point Setup
Access Points
10
STEP 4 (Optional) In the Location field, enter a description of where the access point is
physically located, for example, Reception.
STEP 5 Click Enable Single Point Setup.
The access point automatically joins the Single Point Setup.
Removing an Access Point from a Single Point Setup Cluster
To remove an access point from the Single Point Setup cluster:
STEP 1 In the table showing the detected devices, click the IP address for the clustered
WAP device you want to remove.
The web-based configuration utility for that WAP device shows.
STEP 2 Select Single Point Setup > Access Points in the navigation pane.
STEP 3 Click Disable Single Point Setup.
The Single Point Setup status field for that access point will now show Disabled.
Navigating to Configuration Information for a Specific WAP
Device
All WAP devices in a Single Point Setup cluster reflect the same configuration (if
the configurable items can be propagated). It does not matter which WAP device
you connect to for administration—configuration changes on any WAP device in
the cluster are propagated to the other members.
There may be situations, however, when you want to view or manage information
on a particular WAP device. For example, you might want to check status
information such as client associations or events for an access point. In this case,
you can click the IP address in the table on the Access Points page to show the
web-based configuration utility for the particular access point.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
165
Single Point Setup
Sessions
10
Navigating to a WAP Device Using its IP Address in a URL
You can also link to the web-based configuration utility of a specific WAP device
by entering the IP address for that access point as a URL directly into a web
browser address bar in the following form:
http://IPAddressOfAccessPoint (if using HTTP)
https://IPAddressofAccessPoint (if using HTTPS)
Sessions
The Sessions page shows information on WLAN clients that are associated with
the WAP devices in the Single Point Setup cluster. Each WLAN client is identified
by its MAC address, along with the device location where it is currently
connected.
NOTE The Sessions page shows a maximum of 20 clients per radio on the clustered WAP
devices. To see all WLAN clients associated with a particular WAP device, view the
Status > Associated Clients page directly on that device.
To view a particular statistic for a WLAN client session, select an item from the
Display list and click Go. You can view information about idle time, data rate, and
signal strength.
A session in this context is the period of time in which a user on a client device
(station) with a unique MAC address maintains a connection with the wireless
network. The session begins when the WLAN client logs on to the network, and
the session ends when the WLAN client either logs off intentionally or loses the
connection for some other reason.
NOTE A session is not the same as an association, which describes a WLAN client
connection to a particular access point. A WLAN client association can shift from
one clustered access point to another within the same session.
To view sessions associated with the cluster, select Single Point Setup >
Sessions in the navigation pane.
The following data shows for each WLAN client session with a Single Point Setup.
•
AP Location—The location of the access point.
The location is derived from the location specified on the
Administration > System Settings page.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
166
Single Point Setup
Channel Management
10
•
•
•
User MAC—The MAC address of the wireless client.
A MAC address is a hardware address that uniquely identifies each node of
a network.
Idle—The amount of time this WLAN client has remained inactive.
A WLAN client is considered to be inactive when it is not receiving or
transmitting data.
Rate—The negotiated data rate. Actual transfer rates can vary depending on
overhead.
The data transmission rate is measured in megabits per second (Mbps). The
value should fall within the range of the advertised rate set for the mode in
use on the access point. For example, 6 to 54 Mbps for 802.11a.
•
Signal—The strength of the radio frequency (RF) signal the WLAN client
receives from the access point. The measure is known as Received Signal
Strength Indication (RSSI), and is a value between 0 and 100.
•
•
•
Receive Total—The number of total packets received by the WLAN client
during the current session.
Transmit Total—The number of total packets transmitted to the WLAN client
during this session.
Error Rate—The percentage of time frames are dropped during
transmission on this access point.
To sort the information shown in the tables by a particular indicator, click the
column label you want to sort by. For example, if you want to see the table rows
ordered by signal strength, click the Signal column label.
Channel Management
The Channel Management page shows the current and planned channel
assignments for WAP devices in a Single Point Setup cluster.
When channel management is enabled, the WAP device automatically assigns
radio channels used by WAP devices in a Single Point Setup cluster. Automatic
channel assignment reduces mutual interference (or interference with other WAP
devices outside of its cluster) and maximizes Wi-Fi bandwidth to help maintain
efficient communication over the wireless network.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
167
Single Point Setup
Channel Management
10
The automatic channel assignment feature is disabled by default. The state of
channel management (enabled or disabled) is propagated to the other devices in
the Single Point Setup cluster.
At a specified interval, the channel manager (that is, the device that provided the
configuration to the cluster) maps all clustered WAP devices to different channels
and measures interference levels of the cluster members. If significant channel
interference is detected, the channel manager automatically reassigns some or all
of the devices to new channels per an efficiency algorithm (or automated channel
plan). If the channel manager determines that a change is necessary, then the
reassignment information is sent to all members of the cluster. A syslog message
is generated as well indicating the sender device and the new and old channel
assignments.
To configure and view the channel assignments for the Single Point Setup
members:
STEP 1 Select the Single Point Setup > Channel Management in the navigation pane.
From the Channel Management page, you can view channel assignments for all
WAP devices in the cluster and stop or start automatic channel management. You
can also use the advanced settings to modify the interference reduction potential
that triggers channel reassignment, change the schedule for automatic updates,
and reconfigure the channel set used for assignments.
STEP 2 To start automatic channel assignment, click Start.
Channel management overrides the default cluster behavior, which is to
synchronize radio channels of all WAP devices that are members of the cluster.
When channel management is enabled, the radio channel is not synchronized
across the cluster to other devices.
When automatic channel assignment is enabled, the channel manager periodically
maps radio channels used by WAP devices in a Single Point Setup cluster and, if
necessary, reassigns channels to reduce interference with cluster members or
with devices outside the cluster. The channel policy for the radio is automatically
set to static mode, and the Auto option is not available for the Channel field on the
Wireless > Radio page.
See Viewing Channel Assignments and Setting Locks for information on the
current and proposed channel assignments.
STEP 3 To stop automatic channel assignment, click Stop.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
168
Single Point Setup
Channel Management
10
No channel usage maps or channel reassignments are made. Only manual updates
affect the channel assignment.
Viewing Channel Assignments and Setting Locks
When channel management is enabled, the page shows the Current Channel
Assignations table and the Proposed Channel Assignments table.
Current Channel Assignments Table
The Current Channel Assignments table shows a list of all WAP devices in the
Single Point Setup cluster by IP address.
The table provides the following details on the current channel assignments.
•
•
•
•
•
Location—The physical location of the device.
IP Address—The IP address for the access point.
Wireless Radio—The MAC address of the radio.
Band—The band on which the access point is broadcasting.
Channel—The radio channel on which this access point is currently
broadcasting.
•
•
Locked—Forces the access point to remain on the current channel.
Status—Shows the status of the wireless radio in the device. (Some WAP
devices may have more than one wireless radio; each radio is displayed on
a separate line in the table.) The radio status is up (operational) or down (not
operational).
When selected for an access point, automated channel management plans do not
reassign the WAP devices to a different channel as a part of the optimization
strategy. Instead, WAP devices with locked channels are factored in as
requirements for the plan.
Click Save to update the locked setting. Locked devices show the same channel
for the Current Channel Assignments table and the Proposed Channel
Assignments table. Locked devices keep their current channels.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
169
Single Point Setup
Channel Management
10
Proposed Channel Assignments Table
The Proposed Channel Assignments table shows the proposed channels that are
to be assigned to each WAP device when the next update occurs. Locked
channels are not reassigned—the optimization of channel distribution among
devices takes into account that locked devices must remain on their current
channels. WAP devices that are not locked may be assigned to different channels
than they were previously using, depending on the results of the plan.
For each WAP device in the Single Point Setup, the Proposed Channel
Assignments table shows the location, IP Address, and Wireless Radio, as in the
Current Channel Assignations table. It also shows the Proposed Channel, which is
the radio channel to which this WAP device would be reassigned if the channel
plan is applied.
Configuring Advanced Settings
The Advanced settings area enables you to customize and schedule the channel
plan for the Single Point Setup.
By default, channels are automatically reassigned once every hour, but only if
interference can be reduced by 25 percent or more. Channels are reassigned
even if the network is busy. The default settings are designed to satisfy most
scenarios where you would need to implement channel management.
You can change the Advanced settings to configure the following settings:
•
Change channels if interference is reduced by at least—The minimum
percentage of interference reduction a proposed plan must achieve in
order to be applied. The default is 75 percent. Use the drop-down menu to
choose percentages ranging from 5 percent to 75 percent. Using this
setting lets you set a threshold gain in efficiency for channel reassignment
so that the network is not continually disrupted for minimal gains in
efficiency.
For example, if channel interference must be reduced by 75 percent and
the proposed channel assignments will only reduce interference by 30
percent, then channels will not be reassigned. However, if you reset the
minimal channel interference benefit to 25 percent and click Save, the
proposed channel plan will be implemented and channels will be
reassigned as needed.
•
Determine if there is better set of channels every—The schedule for
automated updates. A range of intervals is provided, from 30 minutes to six
months
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
170
Single Point Setup
Wireless Neighborhood
10
The default is one hour, meaning that channel usage is reassessed and the
resulting channel plan is applied every hour.
If you change these settings, click Save. The changes are saved to the active
configuration and the Startup Configuration.
Wireless Neighborhood
The Wireless Neighborhood page shows up to 20 devices within range of each
wireless radio in the cluster. (For example, if a WAP device has two wireless
radios, 40 devices would be displayed for that device.) The Wireless
Neighborhood page also distinguishes between cluster members and
nonmembers.
The Wireless Neighborhood view can help you:
•
Detect and locate unexpected (or rogue) devices in a wireless domain so
that you can take action to limit associated risks.
•
Verify coverage expectations. By assessing which WAP devices are visible
and at what signal strength from other devices, you can verify that the
deployment meets your planning goals.
•
Detect faults. Unexpected changes in the coverage pattern are evident at a
glance in the color coded table.
To view neighboring devices, select Single Point Setup > Wireless
Neighborhood in the navigation pane. To see all the devices detected on a given
Single Point Setup, navigate to the web interface of a member and select
Wireless > Rogue AP Detection in the navigation pane.
For each neighbor access point, the following information is shown:
•
Display Neighboring APs—Select one of the following radio buttons to
change the view:
-
-
In cluster—Only neighbor WAP devices that are members of the cluster.
Not in cluster—Only neighbor WAP devices that are not cluster
members.
-
Both—Shows all neighbor WAP devices (cluster members and
nonmembers).
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
171
Single Point Setup
Wireless Neighborhood
10
•
Cluster—The list at the top of the table shows IP addresses for all WAP
devices that are clustered together. (This list is the same as the members
list on the Single Point Setup > Access Points page.)
If there is only one WAP device in the cluster, only a single IP address
column shows, indicating that the WAP device is grouped with itself.
You can click on an IP address to view more details on a particular WAP
device.
•
Neighbors—Devices that are neighbors of one or more of the clustered
devices are listed in the left column by SSID (network name).
A device that is detected as neighbor can also be a cluster member itself.
Neighbors who are also cluster members are always shown at the top of the list
with a heavy bar above and include a location indicator.
The colored bars to the right of each WAP device in the Neighbors list shows the
signal strength for each of the neighbor WAP devices, as detected by the cluster
member whose IP address is shown at the top of the column.
The color of the bar indicates the signal strength:
•
•
Dark Blue Bar—A dark blue bar and a high signal strength number (for
example 50) indicates good signal strength detected from the neighbor, as
seen by the device whose IP address is listed above that column.
Lighter Blue Bar—A lighter blue bar and a lower signal strength number (for
example 20 or lower) indicates medium or weak signal strength from the
neighbor, as seen by the device whose IP address is listed above that
column
•
•
•
White Bar—A white bar and the number 0 indicates that a neighboring
device that was detected by one of the cluster members cannot be
detected by the device whose IP address is listed above that column.
Light Gray Bar—A light gray bar and no signal strength number indicates
that no signal has been detected from the neighbor, but the neighbor may
have been detected by other members of the cluster.
Dark Gray Bar—A dark gray bar and no signal strength number indicates
the WAP device itself that corresponds to the IP address listed above it. A
signal strength of zero is displayed because the device’s own signal
strength is not measured.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
172
Single Point Setup
Wireless Neighborhood
10
Viewing Details for a Cluster Member
To view details on a cluster member, click the IP address of a member at the top of
the page.
The following details for the device appear below the Neighbors list.
•
•
•
•
SSID—The Service Set Identifier for the neighboring access point.
MAC Address—The MAC address of the neighboring access point.
Channel—The channel on which the access point is currently broadcasting.
Rate—The rate in megabits per second at which this access point is
currently transmitting. The current rate is always one of the rates shown in
Supported Rates.
•
Signal—The strength of the radio signal detected from the access point,
measured in decibels (dB).
•
•
Beacon Interval—The beacon interval used by the access point.
Beacon Age—The date and time of the last beacon received from this
access point.
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
173
A
Deauthentication Message Reason Codes
When a client deauthenticates from the WAP device, a message is sent to the
system log. The message includes a reason code that may be helpful in
determining why a client was deauthenticated. You can view log messages when
you click Status and Statistics > Log Status.
The following table describes the deauthentication reason codes.
Reason code Meaning
0
1
2
3
Reserved
Unspecified reason
Previous authentication no longer valid
Deauthenticated because sending station (STA) is leaving or has
left Independent Basic Service Set (IBSS) or ESS
4
5
Disassociated due to inactivity
Disassociated because WAP device is unable to handle all
currently associated STAs
6
7
8
Class 2 frame received from nonauthenticated STA
Class 3 frame received from nonassociated STA
Disassociated because sending STA is leaving or has left Basic
Service Set (BSS)
9
STA requesting (re)association is not authenticated with
responding STA
10
Disassociated because the information in the Power Capability
element is unacceptable
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
174
Deauthentication Message Reason Codes
A
Reason code Meaning
11
Disassociated because the information in the Supported
Channels element is unacceptable
12
13
Disassociated due to BSS Transition Management
Invalid element, i.e., an element defined in this standard for
which the content does not meet the specifications in Clause 8
14
15
16
17
Message integrity code (MIC) failure
4-Way Handshake timeout
Group Key Handshake timeout
Element in 4-Way Handshake different from (Re)Association
Request/Probe Response/Beacon frame
18
19
20
21
22
23
24
Invalid group cipher
Invalid pairwise cipher
Invalid AKMP
Unsupported RSNE version
Invalid RSNE capabilities
IEEE 802.1X authentication failed
Cipher suite rejected because of the security policy
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
175
B
Where to Go From Here
Cisco provides a wide range of resources to help you and your customer obtain
the full benefits of the Cisco WAP121 and WAP321 Access Point.
Support
Cisco Small Business
Support Community
Cisco Small Business
Support and Resources
Phone Support Contacts
www.cisco.com/en/US/support/
_support_center_contacts.html
Cisco Small Business
Firmware Downloads
Select a link to download firmware for Cisco Small
Business Products. No login is required.
Downloads for all other Cisco Small Business
products, including Network Storage Systems, are
available in the Download area on Cisco.com at
www.cisco.com/go/software (registration/login
required).
Cisco Small Business Open
Source Requests
Product Documentation
Cisco Small Business
WAP121 and WAP321
Wireless-N Access Point
with PoE Quick Start Guide
and Administration Guide
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
176
Where to Go From Here
B
Cisco Small Business
Cisco Partner Central for
Small Business (Partner
Login Required)
Cisco Small Business
Home
Cisco Small Business WAP121 and WAP321 Wireless-N Access Point with PoE
177
|