I N S T A L L A T I O N I N S T R U C T I O N S
Pipe Adapter for SL-151 Projector Lift
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SMA-602
Installation Instructions
SMA-602
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
3
SMA-602
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
1/2" (12.7mm)
9/16" (14.3mm)
5/32"(included)
PARTS
B (1)
5/16-18 x 1/4"
C (3)
3/8-16 x 3 1/2"
A (1)
[Pipe adapter]
F (1)
5/32"
D (12)
3/8-16"
E (12)
3/8"
4
Installation Instructions
SMA-602
Assembly And Installation
The SMA-602 pipe adapter assembly was designed to attach
the UL-Listed SL151 lift (not included) to a 1-1/2" NPT or NPSM
following ANSI/ASME B1.20.1 (Schedule 40, 0.154" minimum
thickness steel or aluminum - ASTM B221) threaded extension
column (not included). A minimum of four threads must be
engaged.
(C) x 3
1
(underside of SL-151)
(E) x 3
Disassemble Pipe Adapter Assembly
1. Unscrew four hex nuts on pipe adapter assembly (A). (See
Figure 1)
2. Remove top and bottom slide assembly plates from main
plate. (See Figure 1)
hex nuts x 4
1
top slide plate
main plate
Figure 2
(D) x 3
(E) x 3
2
bottom slide plate
(underneath)
Figure 3
(D) x 3
4
Figure 1
Attach Main Plate to SL-151 Lift
1. Insert a 3/8-16 x 3 1/2" hex head tap bolt (C) through a 3/8"
washer (E) and through one of three holes on top of SL-151
lift. (See Figure 2)
2. Install a 3/8" washer (E) and a 3/8-16" hex nut (D) over tap
bolt. (See Figure 3)
3. Repeat Steps 1-2 for other two holes on SL-151 lift.
4. Thread each nut completely on bolts. (See Figure 4)
Figure 4
5
SMA-602
Installation Instructions
5. Partially thread a 3/8-16" hex nut (D) onto each of three 3/
8-16 x 3 1/2" hex head tap bolts (C). (See Figure 5)
Attaching Main Plate and SL-151 to Ceiling Pipe
IMPORTANT ! : Only attach SMA-602 to UL Listed Chief
ceiling mount SL151.
6. Place a 3/8" washer (E) over each hex nut. (See Figure 5)
IMPORTANT ! : These installation instructions assume that a
1-1/2" NPT or NPSM following ANSI/ASME B1.20.1 (Schedule
40, 0.154" minimum thickness aluminum - ASTM B221)
threaded extension column (not included) has been properly
installed and is in place.
7. Place main plate over three bolts lining up the holes on the
outside edge of the plate with the screws. (See Figure 5)
8. Place another 3/8" washer (E) and 3/8-16" hex nut (D) over
each bolt. (See Figure 5)
1. Thread top slide plate assembly onto ceiling pipe until it
cannot be tightened any further. (See Figure 7)
main plate
2. Adjust top slide plate assembly back clockwise until set
screw hole is facing target. (See Figure 7)
(D) x 3
(E) x 3
8
(D) x 3
5
(E) x 3
IMPORTANT ! : When SMA-602 is properly positioned, the
set screw access hole should be pointing directly at target.
3. Insert 5/16-18 x 1/4" set screw (B) into access hole to
secure top slide plate to ceiling pipe. (See Figure 7)
ceiling pipe
1
top slide plate
assembly
2
Figure 5
(B)
3
9. Secure main plate near top of bolts by threading nuts
together. Make sure to leave plenty of space between plate
and SL-151 to allow for easy access in later steps. (See
Figure 6)
Figure 7
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the SMA-602 up to (and
including) the projector does not exceed 105 lbs (47.6 kg).
9
WARNING: Improper installation can result in serious
personal injury or damage to equipment! The SL-151
projector mount weighs in excess of 50 lbs! Use either a
mechanical lifting device or at least two people to lift and
install SL-151.
4. Lift main plate and attached SL-151 underneath top slide
plate making sure the four slots on each plate are
perpendicular to each other. (See Figure 8)
leave space
5. Place bottom slide plate directly underneath main plate
inserting four bolts through four slots in main plate.
6. Insert four bolts up through four slots on top slide plate and
secure using the four hex nuts removed in Step 1 of
Disassemble Pipe Adapter Assembly. (See Figure 8)
Figure 6
6
Installation Instructions
SMA-602
Yaw Adjustment
1. Loosen set screw on top slide plate pipe connector. (See
Figure 10)
removed hex nuts
top slide plate
2. Adjust YAW position until set screw faces target. (See
Figure 10)
bottom slide
3. Tighten set screw on top slide plate pipe connector. (See
Figure 10)
plate (underneath)
main plate
5
6
2
Figure 10
Figure 8
Height Adjustment
7. Lower hex nuts holding main plate in place to bring SL-151
to desired height. (See Figure 8)
1. Adjust hex nuts up or down in order to make sure the SL-
151 is evenly mounted. (See Figure 11)
Adjustments
Location Adjustments
1. Loosen four hex nuts holding plates together. (See Figure 9)
2. Slide SL-151 in either direction until desired mounting
location is reached. (See Figure 9)
3. Tighten four hex nuts holding plates together. (See Figure
9)
1
2
2
Figure 11
Projector Installation
1. Refer to SL-151 Installation Manual for details on mounting
projector to SL-151.
Figure 9
7
SMA-602
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
6436 City West Parkway, Eden Prairie, MN 55344
800.582.6480 / 952.225.6000
877.894.6918 / 952.894.6918
Franklinstraat 14, 6003 DK Weert, Netherlands
+31 (0) 495 580 852
+31 (0) 495 580 845
Chief, a products division of
Milestone AV Technologies
Asia Pacific
A
Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
852 2145 4099
852 2145 4477
8800-002540 Rev00
¤2014 Milestone AV Technologies
03/14
P
F
|