I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Istruzioni di installazione
Installatie-instructies
Instruções de Instalação
Instructions d´installation
Height Adjustable Dual Arm with Keyboard Tray
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
KWK-110
Installation Instructions
KWK-110
LEGEND
Tighten Fastener
Pencil Mark
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Drill Hole
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Phillips Screwdriver
Adjust
Destornillador Phillips
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Remove
Quitar
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Clé à fourche
By Hand
Optional
Opcional
Optional
Opcional
Opzionale
Optie
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Hex-Head Wrench
Security Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Zeskantsleutel
Clé à tête hexagonale
3
KWK-110
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
#2
1/8"
1/4"
(included)
3/16"
(included)
5/32"
(included)
PARTS
B (1)
C (1)
I/M
A (1)
x1
F (6)
D (1)
E (1)
J (2)
#10
G (2)
#8-32 x 3/8"
H (2)
#10 x 2 1/2"
M(1)
L(1)
3/16"
K(1)
1/4"
5/32"
4
Installation Instructions
KWK-110
MOUNT INSTALLATION
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS MOUNT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this mount is attached can support
five times the combined weight of the mount and all
equipment attached to it. Reinforce the structure as required
before installing the mount.
(C)
(A)
5
Mount Installation Using Wood Studs
1. Determine location for mount keeping in mind extension
and height adjustment (if applicable) requirements.
2. Using wall plate (C) as a template, mark then drill two 1/8"
diameter pilot holes through top and bottom holes of wall
bracket into wall structure. (See Figure 1)
6
(H) x 2
3
2
Figure 2
7. Use 5/32" hex driver to tighten set screw in bottom of wall
mount. (See Figure 3)
NOTE: Ensure set screw engages on back side of wall plate to
properly secure wall mount.
(C)
(J) x 2
(A)
Figure 1
3. Install two #10 x 2 1/2" Phillips Pan Head Tapping screws
(H) through #10 washers (J), wall plate (C) and drywall into
wood stud. (See Figure 1)
Set
Screw
4. Ensure wall plate (C) is vertical, then tighten screws (H).
7
CAUTION: Overtightening screws may cause wall bracket
to compress into soft wall surface, resulting in difficult mount
installation or improper engaging of set screw in later step.
Figure 3
5. Insert top of wall mount (A) over lip on top of wall plate (C).
(See Figure 2)
6. Swing wall mount down flush against wall. (See Figure 2)
5
KWK-110
Installation Instructions
CABLE MANAGEMENT
1. Thread keyboard cable through one of two holes along the
back edge of the keyboard tray.
KEYBOARD AND WRIST PAD INSTALLATION
1. Remove adhesive backing from one side of hook and loop
connectors (F).
2. Open the cable management bracket by sliding it towards
the edge of the arm. (See Figure 6)
2. Place hook and loop connectors (F) on bottom of the
keyboard and bottom of wrist pad approximately as shown.
(See Figure 4)
NOTE: If necessary, cable management bracket attach screws
may be loosened using hex key (L).
NOTE: Place connectors only on flat sections of the keyboard
to ensure that they stick to the surface.
3. Remove the adhesive backing from the other side of the
hook and loop connectors (F).
4. Firmly place keyboard on keyboard tray making sure to
leave room for the wrist pad if necessary. (See Figure 4)
Attach
Screws
5. Firmly place wrist pad (D) on keyboard tray in front of the
keyboard. (See Figure 4)
keyboard
(F) x 6
CLOSED Position
View from Bottom
OPEN Position
Figure 6
(D)
CAUTION: Ensure that adequate cable slack exists for
movement of keyboard and mouse, and that cables will not
be pinched when bracket is closed.
3. Carefully insert cables into bracket. (See Figure 7)
(A)
Figure 4
Mouse Holder Installation
1. Remove adhesive backing from mouse holder (E).
2. Place mouse holder (E) on wall at desired location. (See
Figure 5)
Cable Management
Bracket (in open position)
Cable Path (typical)
Figure 7
(A)
4. Close cable management bracket by sliding it back towards
the centerline of the arm.
NOTE: If necessary, cable management bracket attach screws
may be tightened using hex key (L).
5. Carefully insert cables in cavity located in lower portion of
mount arm. (See Figure 8)
6. Using Phillips screwdriver, install cover (B) with two #8-32 x
3/8" Phillips flat screws (G). (See Figure 8)
(E)
Figure 5
6
Installation Instructions
KWK-110
Height Adjustable Screw
Cable Path
(typical)
(B) x 1
(G) x 2
Figure 8
Figure 10
Tray Tension Adjustment
ADJUSTMENTS
1. Using 1/4" hex key (K), slightly loosen or tighten the tray
tension adjustment screw as necessary. (See Figure 11)
Swing Arm
Pivot/Swing
1. Using 3/16" hex key (L), slightly loosen or tighten the
adjustment screw(s) as necessary. (See Figure 9)
Pivot/Swing Adjustment Screws
Tray Tension Adjustment Screw
Figure 11
Adjustable Mouse
Trays
Figure 9
Mouse Tray Adjustment
1. Mouse trays slide open and closed on both sides of the tray
for both right-handed and left-handed users. (See Figure 9)
Height Adjustable
1. Using 5/32" hex key (M), slightly loosen or tighten the
adjustment screw as necessary. (See Figure 10)
•
If display settles on its own, rotate adjustment
screw counterclockwise (towards the "+" symbol).
•
If display rises on its own, rotate adjustment
screw clockwise (towards the "-" symbol).
NOTE: It may be necessary to raise or lower the height
adjustable arm to expose the adjustment screw.
7
KWK-110
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Chief Manufacturing, a division of
Milestone AV Technologies
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8834-000005
P
F
+86-755-8996 9226
+86-755-8996 9217
©2008 Milestone AV Technologies
10/08
|