I N S T A L L A T I O N I N S T R U C T I O N S
Horizontal And Vertical Table Stands
and Accessories
Model: KTP-Series
The KTP-Series is a free standing, pole mount solution for multiple displays.
KTP-320
KTP-220 / KTP-225
KTP-440 / KTP-445
KTP-230
BEFORE YOU BEGIN
CAUTION!
To prevent damage to the Kit, which could affect or void the Factory warranty, and to the equipment that will be
attached to it, thoroughly study all instructions and illustrations before you begin the installation.
•
If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.
Chief® and Centris™ are trademarks of Milestone AV Technologies. All rights reserved.
8832-000142 Rev I
¤2008 Milestone AV Technologies,
a Duchossois Group Company
Chief Manufacturing, a products division of
Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
P: 800.582.6480 / 952.894.6280
11/08
Installation Instructions
Model: KTP-Series
(160)
(10 Includes 210, 220, 230)
(180)
(200)
(120)
(190)
(170)
(20)
(130)
(140)
250
260
(30)
(110)
(100)
(40)
240
(80)
(90)
(50)
(70)
(60)
Figure 1: Parts
ASSEMBLY AND INSTALLATION
(210)
(60)
Mount Assembly
KTP-230 Assembly
To assemble the KTP-230:
(220)
1. Assemble pole (60) to base (40) using one 3/8-16 x 1"
FHCS (90). (see Figure 2)
(60)
(230)
(140)
Figure 3: Mount Centris Head with Pole Clamp
(90)
(40)
Figure 2: Assemble Pole to Base
2. Place front pole clamp, with Centris Head, (210)
against pole in approximate mounting location.
3. Place three BHCS (230) into rear pole clamp (220)
and place against pole aligning with front pole clamp
(210). (see Figure 3)
3
Model: KTP-Series
Installation Instructions
NOTE: Equally tighten screws (230) against front pole
mount (210) and rear (220) pole clamps.
(see Figure 4)
Display Installation
Attach Centris Head to Flush Mount Display
CAUTION!
CAUTION: If display uses a screw size other than
those included in the kit, DO NOT use the screws
provided. Using the wrong screws could result in
damage to your monitor.
(230)
Keep equal
distance between
mount and
clamp when
tightening
(220)
1. Install two M4 x 12mm Phillips pan head screws (160)
into two upper mounting holes in display back.
(see Figure 6)
NOTE: DO NOT fully tighten at this time.
(210)
2. Hang display on Centris head. (see Figure 7)
Figure 4:
3. Install bottom two M4 x 12mm Phillips pan head
screws (160) through Centris head mounting holes
and into lower mounting holes in display back.
4. Secure rear pole clamp (220) to front pole mount
(210) and pole by tightening three BHCS (230) using
5/32" hex key (120). (see Figure 3)
4. Tighten ALL four M4 x 12mm Phillips pan head
screws (160). (see Figure 8)
KTP-220, 320, and 440 Assembly
To assemble the KTP-220, 320, and 440:
M4 x 12mm Phillips Pan Head Screw (30)
1. Assemble pole (50) to base (40) using one 3/8-16 x 1"
FHCS (90). (see Figure 2)
2. Assemble pole clamp back (240) to pole mount front
using two FW (250) and two BHCS (260) using a
5/32" hex key. (see Figure 5)
3. Secure pole mount back (240) to pole mount front and
pole by tightening two BHCS (260) using a 5/32" hex
key.
Display
Pole
Pole Mount front
with Array
Figure 6: Prepare Display
(250)
Display
(260)
(20, 30)
Pole Clamp Back (240)
Centris Head
Figure 5: Assemble Array Rail to Pole
Figure 7: Hang Display
4
Installation Instructions
Centris Head
Model: KTP-Series
3. Place display face down on a clean dry surface.
Display
4. Place four 3/8" or 3/4" nylon spacers (190 or 200)
over four mounting holes in display back (see Figure
11).
5. Align Centris head mounting holes with four nylon
spacers (see Figure 11).
6. Secure Centris head to display using four
M4 x 20mm Phillips pan head screws (170), or four
M4 x 30mm Phillips pan head screws (180)
(see Figure 11).
(20, 30)
(160)
Phillips Pan Head Screw
(170 or 180)
Centris Head
Figure 8: Secure Display to Centris Bracket
Attach Centris Head to Recessed Mount Display
Spacer
(190 or 200)
NOTE: Refer to Table 3 to select the applicable screw
and spacer combination.
1. Uninstall end lock using the 5/32" hex key (120).
(see Figure 9)
2. Remove Centris head from array rail (20, 30).
Centris Head
Square Nut
Display
Figure 11: Mount Centris Bracket to Display
7. Slide display with Centris bracket onto array rail (20,
30) (see Figure 12).
NOTE: Repeat previous steps for each additional display.
End Lock
(20, 30)
8. Reinstall end locks into mounting rail using the 5/32"
hex key (120) (see Figure 13).
Figure 9: Remove End Lock(s)
Display with Centris Bracket
(20, 30)
(20, 30)
Centris Head
Figure 10: Slide Centris Bracket off Array Rail
Figure 12: Mount Display with Centris Bracket to
Array Rail
5
Model: KTP-Series
Installation Instructions
Display Pitch and Roll Adjustment
To adjust display pitch or roll position:
(20, 30)
1. Loosen Centris bracket front adjustment knob.
(see Figure 15)
End Lock
2. Tilt display up or down, or adjust display roll left or
right until properly positioned.
3. Tighten Centris bracket front adjustmnent knob.
Pitch/Roll
Adjustment
Knob
Centris Head
End Lock Retaining Screw
Figure 13: Reinstall End Lock(s)
ADJUSTMENTS
Display Adjustment
The KTP Series mount allows horizontal, pitch, and
rotational adjustment of each display.
The KTP Series mount also allows a full 360 deg. of
display rotation with a maximum pitch range of 15° up
and 15° down.
Figure 15: Display Pitch and Roll Adjustment
Display Horizontal Position Adjustment
CABLE MANAGEMENT
To adjust display horizontal position:
The KTP Series mount includes cable management
features used to properly route and secure display
cables.
1. Loosen Centris bracket rear adjustment knob (see
Figure 14).
2. Slide Centris bracket with display left or right until
properly positioned on array rail.
To use the cable management features:
1. Connect cables to display.
3. Tighten Centris bracket rear adjustmnent knob.
2. Route cables through cable clips on array rail.
3. Route cables down pole and away from mount and
secure to pole using sheath (80).
Horizontal
Adjustment
Knob
Cable Clips
(80)
Figure 16: Cable Management
Figure 14: Display Horizontal Adjustment
6
Installation Instructions
Model: KTP-Series
7
|