I N S T A L L A T I O N I N S T R U C T I O N S
Universal Slat Wall
Dual Arm Mounts
KSG110
Installation Instructions
KSG110
LEGEND
Pencil Mark
Tighten Fastener
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Drill Hole
Loosen Fastener
Perforar
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Percez un trou
Adjust
Phillips Screwdriver
Ajustar
Destornillador Phillips
Einstellen
Ajustar
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Regolare
Afstellen
Ajuster
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Remove
Quitar
Open-Ended Wrench
Llave de boca
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Optional
Opcional
Optional
Opcional
Opzionale
Optie
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
En option
Security Wrench
Hex-Head Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
3
KSG110
Installation Instructions
TOOLS REQUIRED FOR INSTALLATION
3/16"
5/32"
(Provided)
(Provided)
PARTS
A (1)
B (1)
E (1)
C (1)
3/16"
D (1)
5/32"
G1
G5
G4
G2
F (2)
8-32 x 3/8"
G3
G (1)
4
Installation Instructions
KSG110
INSTALLATION
B
WARNING: FAILURE TO PROVIDE ADEQUATE
STRUCTURAL STRENGTH FOR THIS COMPONENT CAN
RESULT IN SERIOUS PERSONAL INJURY OR DAMAGE
TO EQUIPMENT! It is the installer’s responsibility to make
sure the structure to which this component is attached can
support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
1. Install the slat wall bracket (B) following the instructions
included with kit.
IMPORTANT ! : If the display being installed has a recessed
mounting surface, the display must be assembled to the mount
prior to mount installation. See Display Installation in this
document before proceeding.
3
A
2. Insert top of mount (A) over lip on top of wall bracket (B).
(See Figure 1)
Figure 2
4. Tighten set screw using 5/32" hex key (D). (See Figure 3)
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Make sure set
screw engages back side of mounting dish on wall bracket
(B). (See Figure 3)
A
2
A
B
B
4
Figure 1
3. Swing mount (A) down flush against wall bracket (B). (See
Figure 2)
Figure 3
DISPLAY INSTALLATION
The mounting holes on the back of the display will be flush with
the back surface, or recessed into the back. Refer to the
applicable installation procedure below.
Swing Arm Flush Display Installation
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
5
KSG110
Installation Instructions
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
bracket!
Centris Cup
4
1. Ensure Centris cup is able to swivel and tilt easily, yet still
be tight enough to hold display in desired position. Adjust
as required before proceeding. See "ADJUSTMENT" for
detail.
G1 x 2
2. Using Phillips screwdriver, carefully install two screws (G1)
into the upper mounting holes on the display. Thread
screws completely into display, then back out 3 complete
turns.
3. Align two screws (G1) (installed on the back of the display
in the previous step) with the two top teardrop mounting
holes on the Centris cup.
Figure 5
6. Proceed to "CABLE MANAGEMENT."
Swing Arm Recessed Display Installation
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Smaller area of
teardrop mounting holes must be facing downward for proper
installation. Reposition Centris cup if required.
1. Ensure Centris bracket is able to swivel and tilt easily, yet
still be tight enough to hold display in desired position.
Adjust as required before proceeding. See
"ADJUSTMENT" for detail.
2. Carefully place display face down on a clean and dry
surface.
3. Determine depth of recessed mounting holes relative to
back surface of display.
4. Select proper length spacer and screw from table below:
G1 x 2
IMPORTANT ! : All spacers used should be the same length.
If the recess depths result in multiple spacer lengths, then
2
select the longer spacer.
IF recess DEPTH is: THEN use spacer:
3/8" or less G4 (3/8" long)
AND screw:
3
G2 (G4 x 20mm)
G3 (G4 x 30mm)
More than 3/8" up to G5 (3/4" long)
and including 3/4"
5. Place the four (G4 or G5) spacers over each mounting hole
on the back of display. (See Figure 6)
6. Orient mount so that mounting holes in the Centris cup are
aligned with the holes in the spacers (G4 or G5); rotate the
Centris cup as required (See Figure 6).
Centris Cup
Figure 4
4. Using Phillips screwdriver, install two screws (G1) through
the lower mounting holes in Centris cup into the display.
CAUTION: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
5. Tighten all screws (G1). Do not overtighten!
7. Using Phillips screwdriver, install four screws (G2 or G3)
through the mounting holes in Centris cup, through the
spacers (G4 or G5), into display (See Figure 6).
8. Tighten all four screws. Do not overtighten!
9. Return to mount installation section to continue.
6
Installation Instructions
Centris Cup
KSG110
G2 or G3
(4 places)
7
G4 or G5
(4 places)
Cable Management
Bracket (in open position)
5
Cable Path (typical)
NOTE: Display not shown for clarity.
Figure 8
4. Close cable management bracket by sliding it back towards
the centerline of the arm (See Figure 7).
Figure 6
NOTE: If necessary, cable management bracket attach screws
may be tightened using hex key.
Cable Management
1. Attach all cables to display.
2. Open the cable management bracket by sliding it towards
the edge of the arm (See Figure 7).
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cover (E) or screws (F).
NOTE: If necessary, cable management bracket attach screws
may be loosened using hex key.
5. Carefully insert cables in cavity located in lower portion of
mount arm (See Figure 9).
6. Using Phillips screwdriver, install cover (E) with two
screws (F).
Attach
Screws
Cable Path
(typical)
CLOSED Position
View from Bottom
OPEN Position
Figure 7
E
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched
when bracket is closed.
F x 2
3. Carefully insert cables into bracket (See Figure 8).
Figure 9
Installation is complete.
Adjustments
Centris Head Tension Adjustment
1. If previously attached, disconnect cables from
display, remove display.
7
KSG110
Installation Instructions
2. Using Phillips screwdriver, slightly loosen or tighten
the adjustment screw as necessary (See Figure 10).
Adjustment Screw
2
Figure 10
3. Reinstall display. See Display Installation in this
document.
Display Adjustment
Lateral position on display:
Figure 12
1. Using your fingers, slightly loosen adjustment knob "A".
(See Figure 11)
2. Slide display to desired position.
3. Using your fingers, tighten adjustment knob "A". (See
Figure 11)
PITCH / YAW / ROLL Tension
1. Using your fingers, slightly loosen adjustment knob "B".
(See Figure 11)
2. Adjust display as desired.
3. Using your fingers, tighten adjustment knob "B".
B
A
Figure 11
Swing Arm Tension
1. Using 3/16" hex wrench (C), loosen or tighten adjustment
screw(s) as necessary (See Figure 12).
8
Installation Instructions
KSG110
9
KSG110
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
+31 (0)40 2668615
Asia Pacific
A
Room 30I, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA. Post Code: 518112
8832-000237
¤2007 Chief Manufacturing
08/07
P
F
+86-755-8996 9226 ; 8996 9236 ; 8996 9220
+86-755-8996 9217
|