Corner Unit with
built-in trash bag holder
S A F E U S E , C A R E A N D A S S E M B L Y M A N U A L
1 - Y E A R L I M I T E D W A R R A N T Y
8 5 - 1 0 6 6 - 6 ( A 0 1 0 0 1 )
Read and save this manual for future reference. If pre-assembled, leave this manual with unit for consumer’s future reference.
For product inquiries, parts, and warranty, please call
1-877-707-5463
I M P O R T A N T
Do not use if temperature falls below 0C (32F). Periodically check all hardware and plastic
parts for wear. Please retain these instructions for future reference. Please keep sales
receipt for proof of purchase.
•
W A R N I N G S
Please keep all assembly hardware, tools and packaging away from children.
•
Dispose of unused parts and their packages promptly.
•
Do not allow children to play in or around product.
•
Weight limit trash holder is 15lb.
•
Weight limit for the counter top is 20 lb (9 kg).
•
Remove trash from unit after every use to avoid attracting animals, and insects.
C A R E A N D
Do not use abrasive cleaners to clean any painted, porcelain or stainless steel parts. Exterior
surfaces should be cleaned with warm soapy water, and dried thoroughly.
M A I N T E N A N C E
To protect against corrosion and discoloration please read the following.
Stainless Steel performs best when clean- cleanliness is essential for maximum resistance to
corrosion. There are various practices for cleaning stainless Steel in use. This includes meth-
ods for removing free-iron contamination on stainless Steel surfaces. The salt air environ-
ment of coastal areas or a high humidity environment can be corrosive to Stainless Steel
finishes. These conditions can cause rusting. Other contaminates include dirt, debris,
residue from cleaners (many cleaners contain corrosive ingredients which require thorough
post clean rinsing with clean water) or other material, hinders the passivation process and
traps corrosive agents to the stainless steel, reducing corrosion protection. Routine clean-
ing is necessary to preserve and protect the appearance and integrity of the surface.
To clean stainless Steel surfaces, use a soft cloth and clean warm water to remove mild
stains and loose dirt. Other cleaning agents include a stainless steel cleaner, a non-abrasive,
chloride free, non-acidic cleaner, or simply a vinegar and water solution. Always wipe in the
direction of the grain and ensure that the unit is dried thoroughly after cleaning. DO not
use steel wool, as it will scratch the finish.
1
8 5 - 1 0 6 6 - 6 ( A 0 1 0 0 1 )
A
B
J
J
E
G
C
F
D
H
I
Item No.
Quantity
Specification
Top Lid
Part No.
P A R T S L I S T
A
B
C
D
E
F
1
1
1
1
1
1
1
1
1
2
A010-0001-01
A010-0100-01
A010-0003-01
A010-0005-01
A010-0006-01
A010-0002-01
A010-0007-01
A010-0004-01
G401-0062-01
A011-0039-01
8 5 - 1 0 6 6 - 6 ( A 0 1 0 0 1 )
Top Panel Assembly
Front Shelf
Left Side Panel
Right Side Panel
Back Shelf, Left
Back Shelf, Right
Bottom Shelf
Caster Assembly
Joint Hook
G
H
I
J
2
A S S E M B L Y I N S T R U C T I O N S
Tools Needed for Assembly
Hardware Pack List
No.
Description
Part Number
Quantity
1
1/4-20UNCx13Screw
Ø7 Lock Washer
Ø7 Washer
20120-13013-250
41400-07000-250
40300-07000-250
30220-13000-250
20124-10010-250
41400-05000-250
40300-05000-250
G401-0071-0182
6
2
6
•
•
•
•
Hammer
Slotted screwdriver
Safety glasses
3
6
®
#3 Phillips screwdriver
4
1/4”-20UNC NUT
NO.10-24UNCx10 Screw
Ø5 Lock Washer
Ø5 Washer
2
5
12
12
12
1
Before assembling the cart, read these instructions carefully.
Assemble the cart on a flat, clean surface.
6
7
8
Wrench
Notes: Do not fully tighten all the nuts during this initial stage.
You may have extra hardware after assembly is complete.
#1 – 1/4-20UNCx13Screw (6)
#5 – NO.10-24UNCx10 Screw (12)
#3 – Ø7 Washer (6)
#4 – 1/4”-20UNC NUT (2)
#7 – Ø5 Washer (12)
#2 – Ø7 Lock Washer (6)
#6 – Ø5 Lock Washer (12)
3
Fig. 1
Fig. 2
Fig. 3
H
1
Assemble the three casters (I ) to the bottom shelf (H) as shown.
I
2
Assemble the left side panel (D) to the bottom shelf (H) using hard-
ware #1, #2, #3, and #4 (x2) to Affix the front part of the left
side panel (D) to the bottom shelf (H).
E
D
Affix the right side panel (E) to the bottom shelf (H) using hardware
#1, #2, #3, and #4 (x2). Place the front shelf (C) between two side
panels (D & E) as shown. Use hardware #5, #6, and #7 (x6) as
shown to connect together with both side panels.
C
H
D
G
3
Affix the left and right back shelf ( F & G) to the bottom panel using
hardware #1, #2, #-3, and #4 (x2) as shown.
Then Affix each back shelf to the side shelf using hardware #5, #6,
and #7 (x6).
C
F
H
4
Fig. 4
4
B
Assemble the top panel assembly (B) to the cart assembly using
hardware #1, #2 and #3 (x4). Must fix the top panel (B) to the front
and both side panels.
5
D I S T R I B U T O R
Trileaf Distribution Trifeuil
Toronto, Canada
M4S 2B8
|