MA1011-EA
Operation Guide 5181
ENGLISH
Congratulations upon your selection of this CASIO watch.
x Note that the product illustrations in this manual are intended for reference only,
and so the actual product may appear somewhat different than depicted by an
illustration.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
or loss suffered by you or any third party arising through the use of this product or
its malfunction.
E-1
About This Manual
Things to check before using the watch
Button operations are indicated using the letters A
through D shown in the illustration.
B
@
+
1. Hold down C at least two seconds to enter the Timekeeping Mode, and then
observe the movement of the xSecond Hand.
Hand Functions
z Hour Hand
x Second Hand
c Minute Hand
Is the xSecond Hand moving smoothly in one-second intervals?
NO
YES
v Left Dial Hand: Indicates the current mode.
b Lower Dial Hand
n Right Dial Hands: Indicate a time, in 24-hour format,
depending on the current mode.
m Day
The watch is charged sufficiently.
For details about charging, see
“Charging the Watch” (page E-8).
Is the xSecond Hand moving at
two-second intervals or is it stopped
completely?
ꢀꢁ
>
5
*
6
YES
NEXT
Power is low. Charge the watch by placing
it in a location where it is exposed to light.
For details, see “Charging the Watch”
(page E-8).
Go to step 2.
This User’s Guide uses numbers shown above to identify
watch hands and indicators.
E-2
E-3
E-5
E-7
2. Check the Home City and the daylight saving time (DST) setting.
Contents
Use the procedure under “To configure Home City settings” (page E-20) to configure
your Home City and daylight saving time settings.
E-2
E-3
E-8
About This Manual
Things to check before using the watch
Important!
Charging the Watch
Proper World Time setting depends on correct Home City, time, and date settings in
the Timekeeping Mode. Make sure you configure these settings correctly.
E-15 To recover from the sleep state
E-16 Mode Reference Guide
3. Set the current time.
E-17 To determine the watch’s current mode
E-17 To return to the Timekeeping Mode from any other mode
E-18 To select a mode
See “Configuring Current Time and Date Settings” (page E-24).
The watch is now ready for use.
E-19 Timekeeping
E-20 Configuring Home City Settings
E-20 To configure Home City settings
E-4
E-22 To toggle the Home City time between standard time and daylight
saving time
E-39 To specify standard time or daylight saving time (DST) for a city
E-41 To swap your Home City and World Time City
E-24 Configuring Current Time and Date Settings
E-24 To change the current time setting
E-27 To change the current date setting
E-43 Using the Alarm
E-44 To change the alarm time setting
E-44 To turn the alarm on or off
E-44 To stop the alarm
E-30 Using the Stopwatch
E-31 To perform elapsed time measurement
E-31 To perform an elapsed time operation
E-31 To pause at a split time
E-45 Adjusting the Home Positions
E-45 To adjust the home positions
E-49 Troubleshooting
E-54 Specifications
E-33 Using the Countdown Timer
E-34 To specify the countdown start time
E-35 To perform a countdown timer operation
E-36 To stop the alarm
E-37 Checking the Current Time in a Different Time Zone
E-38 To view the time in another time zone
E-6
Warning!
Charging the Watch
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become
particularly hot when exposed to the following conditions for long periods.
x On the dashboard of a car parked in direct sunlight
The face of the watch is a solar cell that generates power from light. The generated
power charges a built-in rechargeable battery, which powers watch operations. The
watch charges whenever it is exposed to light.
x Too close to an incandescent lamp
x Under direct sunlight
Charging Guide
Whenever you are not
wearing the watch, be sure
to leave it in a location
where it is exposed to light.
x Best charging
performance is achieved
by exposing the watch to
light that is as strong as
possible.
When wearing the watch,
makes sure that its face is
not blocked from light by the
sleeve of your clothing.
x The watch may enter a
sleep state (page E-14) if
its face is blocked by your
sleeve even only partially.
Important!
x Keep the watch in an area normally exposed to bright light when storing it for long
periods. This helps to ensure that power does not run down.
x Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause power to run down.
Make sure that the watch is exposed to bright light whenever possible.
E-8
E-9
Operation Guide 5181
B
+
x The watch will exit the setting mode automatically if
you do not perform any operation for about two or
three minutes.
x For details about city codes, see the “City Code
Table” at the back of this manual.
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
Note
x This watch does not have a city code that corresponds
to Newfoundland.
2. To change the Home City setting, press D to move the
xSecond Hand clockwise.
ꢀꢁ
x Keep pressing D until the xSecond Hand is pointing
at the city code you want to select as your Home City.
x Each time you select a city code, the zHour Hand,
cMinute Hand, bLower Dial Hand and mDay
move to the current time and date for that city code.
Do not perform the next operation until these hands
stop moving.
1. In the Timekeeping Mode, keep A depressed (for about
ꢀꢁ
five seconds) as the xSecond Hand moves to the city
5
> *
@
code of the currently selected Home City.
x This indicates the city code setting mode.
@
3. Press B to toggle the time for the currently selected city code between STD
(standard time)/DST (daylight saving time).
x In the city code setting mode, the vLeft Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
E-20
E-21
x Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
3. After the setting is the way you want, press A to return to the Timekeeping Mode.
Note
4. After all the settings are the way you want, press A to return to the Timekeeping
Mode.
x After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time
in your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping. The
reference point for UTC is Greenwich, England.
To toggle the Home City time between standard time and daylight saving time
1. Perform the step 1 under “To configure Home City settings” on page E-20.
x Each time you select a city code, the zHour Hand, cMinute Hand, and
bLower Dial Hand move to the current time for that city code. Do not perform
the next operation until these hands stop moving.
2. Press B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
x In the city code setting mode, the vLeft Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
x Note that you cannot switch between STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
E-22
E-23
B
@
+
2. Change the Home City and daylight saving time (DST)
settings, if you want.
x For details about these settings, see steps 2 and 3
under “To configure Home City settings” (page E-20).
x In the following steps, each press of C cycles
between settings as shown below.
Configuring Current Time and Date Settings
You can configure current time and date settings.
To change the current time setting
1. In the Timekeeping Mode, keep A depressed (for about
five seconds) as the xSecond Hand moves to the city
code of the currently selected Home City.
Home city/DST
Hour/Minute
Day
Year
ꢀꢁ
x At this time, the vLeft Dial Hand will indicate the
Home City’s current daylight saving time setting (STD
or DST).
ꢀꢁ
Month
>
*
3. Press C.
>
@
x The watch will beep, and the xSecond Hand and
vLeft Dial Hand will move to their 12 o’clock
positions. This is the time setting mode.
E-24
E-25
To change the current date setting
1. In the Timekeeping Mode, keep A depressed (for
4. Use D (+) and B (–) to change the time (hour and minute) setting.
x Each press of either button will move the hands (zHour Hand and cMinute
Hand) one minute.
x Holding down D or B will start high-speed zHour Hand and cMinute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
x The bLower Dial Hand and zHour Hand move in sync with each other.
x When setting the time, make sure that the bLower Dial Hand indicates the
proper a.m./p.m. hour.
x If you want to change the date setting at this time, press C and perform the
procedure starting from step 3 under “To change the current date setting” (page
E-27).
00
about five seconds) as the xSecond Hand moves to
>
the city code of the currently selected Home City.
90
10
2. Press C twice.
x The watch will beep and change to the year setting
80
70
20
30
mode.
x The year can be set in the range of 2000 to 2099.
3. Use D and B to change the year setting.
x Each press of B will move the vLeft Dial Hand and
change the tens digit of the year setting.
60
40
50
Setting the year (tens digit)
5. After the time setting is the way you want, press A to return to the Timekeeping
Mode.
x This will cause the xSecond Hand to move automatically to 12 o’clock and
resume movement from there.
E-26
E-27
@
@
0
6
1
5
x Each press of D will move the xSecond Hand
7. Use D (+) and B (–) to change the mDay setting.
x If you want to change the time setting at this time,
press C and then perform the procedure starting
from step 3 under “To change the current time setting”
(page E-24).
2
3
4
and change the ones digit of the year setting.
4. After the year setting is the way you want, press C.
x The watch will beep and change to the month
setting mode.
9
8
8. After the settings are the way you want, press A to
return to the Timekeeping Mode.
x This will cause the xSecond Hand to move
automatically to 12 o’clock and resume movement
from there.
x The day of the week indicated by the vLeft Dial
Hand changes automatically in accordance with the
date (year, month, and day).
7
Setting the year (ones digit)
ꢀꢁ
Dec
Nov Jan
5. Use D to move the xSecond Hand to the month
setting you want.
Oct
Sep
Aug
Feb
Mar
Apr
>
5
6. After the month setting is the way you want, press
C.
x The watch will beep and change to the day setting
mode.
Note
x The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s rechargeable battery replaced or after
power drops to Level 3.
@
Jun
Jul
May
Setting the month
E-28
E-29
Operation Guide 5181
To perform elapsed time measurement
1. Use C to move the vLeft Dial Hand to
Using the Stopwatch
The stopwatch measures elapsed time and split times.
.
2. Now you can perform either of following stopwatch operations.
@
Hand Functions
To perform an elapsed time operation
x Second Hand: Indicates the stopwatch seconds count.
v Left Dial Hand: Indicates the stopwatch 1/20-second
B
B
B
B
D
count.
Start
Stop
(Restart)
(Stop)
Reset
n Right Dial Hands: Indicate the stopwatch hours and
minutes.
To pause at a split time
ꢀꢁ
B
D
B
D
Normal stopwatch hand movement will
resume automatically after five seconds.
Start
Split
Stop
Reset
>
6
E-30
E-31
Note
Using the Countdown Timer
The countdown timer can be configured to start automatically at a preset time, and
sound an alarm when the end of the countdown is reached.
x The Stopwatch Mode can indicate elapsed time up to 23 hours, 59 minutes, 59.95
seconds.
x D button operation (split, reset) is disabled while hands are moving at high speed
following a reset operation and when transitioning from a split time back to normal
elapsed timekeeping.
x Once started, stopwatch timing continues until you press B to stop it, even if you
exit the Stopwatch Mode to another mode and even if timing reaches the stopwatch
limit defined above.
x You can press B to start an elapsed time operation immediately after entering the
Stopwatch Mode, even if the watch’s hands are still moving to their initial Stopwatch
Mode positions. Note, however, that if the stopwatch was not reset after the last
elapsed time operation, timing will restart from where it was last stopped, and not
from 0.
x The vLeft Dial Hand indicates the 1/20-second count for the first 30 seconds of
a stopwatch elapsed time operation. After that, the hand stops at 0. 1/20-second
timing continues internally after the first 30 seconds, and the vLeft Dial Hand will
jump to the current value whenever B (Stop) or D (Split) is pressed.
@
Hand Functions
x Second Hand:
Moves counter-clockwise to countdown the seconds.
Automatically switches to clockwise movement after
the end of the countdown is reached to count up the
seconds of the elapsed time operation.
v Left Dial Hand: Points to TMR.
n Right Dial Hands:
ꢀꢁ
Move counter-clockwise to countdown the hours and
minutes. Automatically switch to clockwise movement
after the end of the countdown is reached to count up
the hours and minutes of the elapsed time operation.
>
6
E-32
E-33
To specify the countdown start time
To perform a countdown timer operation
1. Use C to move the vLeft Dial Hand to TMR.
B
B
B
B
D
2. After confirming that the xSecond Hand is stopped (which indicates there is no
ongoing countdown timer operation), press D.
x If the xSecond Hand is moving, press B to stop it and then press D.
Start
Stop
(Restart)
(Stop)
Reset
x Before starting a countdown timer operation, check to make sure that the
countdown timer is not already operating (indicated by a moving xSecond Hand).
If it is, press B to stop it and then D to reset to the countdown start time.
x An alarm sounds for 10 seconds when the end of the countdown is reached. This
alarm will sound in all modes.
x While a countdown operation is in progress, the xSecond Hand and nRight Dial
Hands move counterclockwise. When the end of a countdown is reached, the x
Second Hand and nRight Dial Hands change direction and start moving clockwise
to measure elapsed time after the end of the countdown. The elapsed time
operation continues until you press B to stop it.
3. Use D (+) and A (–) to specify the countdown start time.
x Each press of either button will move the nRight Dial Hands one minute.
x Holding down D or A will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
x The maximum countdown start time setting is 24 hours. To set a countdown start
time of 24 hours, move the nRight Dial Hands to 24.
x The maximum time measured by the elapsed time operation that starts after a
countdown is complete is 23 hours, 59 minutes, 59 seconds.
E-34
E-35
To stop the alarm
Press any button.
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to view the current time in one of 29 time zones
around the globe. The city that is currently selected in the World Time Mode is called
the “World Time City”.
Note
x Pressing any button while the alarm is sounding simply stops the alarm sound.
It does not stop the elapsed time operation that started when the end of the
countdown was reached. To stop the elapsed time operation, press B.
Hand Functions
@
x Second Hand:
Indicates the currently selected World Time City.
v Left Dial Hand:
Indicates the current STD or DST setting of the
currently selected time zone.
n Right Dial Hands:
ꢀꢁ
Indicate the current time in the selected World Time
City in 24-hour format.
>
6
E-36
E-37
To view the time in another time zone
To specify standard time or daylight saving time (DST) for a city
1. Use C to move the vLeft Dial Hand to STD or DST.
x The xSecond Hand will move to the city code of the currently selected World
Time City.
1. In the World Time Mode, use D to select the city code
whose setting you want to change.
x Wait until the nRight Dial Hands complete their
move to the time in the currently selected World
Time City. You will not be able to perform step 2 of
this procedure until the hands stop moving.
2. Use D to move the xSecond Hand to the city code you want to select as the
World Time City.
x The nRight Dial Hands will move to the current time in the time zone of the
current city code. At this time, the zHour Hand and cMinute Hand will
continue to indicate the current time in the Home City.
x For full information on city codes, see the “City Code Table” at the back of this
manual.
x If you think that the time indicated for the selected time zone is not correct, it
probably means that there is something wrong with your Home City settings. Use
the procedure under “To configure Home City settings” (page E-20) to correct
the Home City settings.
ꢀꢁ
2. Hold down A for about two seconds until the watch
beeps. This will cause the vLeft Dial Hand to toggle
between DST and STD.
x Note that you cannot switch between STD/DST
while UTC is selected as the World Time City.
x Note that the STD/DST setting affects only the
currently selected time zone. Other time zones are
not affected.
>
6
Hold down
A for two
seconds
E-38
E-39
Operation Guide 5181
Swapping your Home City and World Time City
To swap your Home City and World Time City
You can use the procedure below to swap your Home City and World Time City. This
capability can come in handy when you frequently travel between two locations in
different time zones.
1. In the World Time Mode, use D to select the World
6
Time City you want.
x In this example, you would move the xSecond Hand
to NEW YORK (NYC) in order to select New York as
the World Time City.
x Wait until the nRight Dial Hands complete their
move to the time in the currently selected World Time
City. You will not be able to perform step 2 of this
procedure until the hands stop moving.
The following example shows what happens when the
@
Home City and World Time City are swapped while the
Home City originally is TOKYO (TYO) and the World Time
City is NEW YORK (NYC).
ꢀꢁ
Home City
World Time City
2. Hold down B for about three seconds until the watch
beeps.
x This will make the World Time City (NEW YORK (NYC)
in this example) your new Home City. At the same
time, it will change the Home City you had selected
prior to step 2 (TOKYO (TYO) in this example), to your
World Time City.
TOKYO (TYO)
10:08 p.m.
NEW YORK (NYC)
9:08 a.m.
Before
ꢀꢁ
@
swapping
(Standard time)
(Daylight saving time)
NEW YORK (NYC)
9:08 a.m.
(Daylight saving time)
TOKYO (TYO)
10:08 p.m.
(Standard time)
After
swapping
E-40
E-41
x After swapping the Home City and World Time City, the watch will stay in the
World Time Mode. The xSecond Hand will point to your new World Time City
(TOKYO (TYO) in this example).
x The nRight Dial Hands will indicate the current time in your new World Time
City.
Using the Alarm
When the alarm is turned on, an alarm will sound for about 10 seconds each day
when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
Hand Functions
@
x Second Hand:
Indicates the current alarm ON/OFF setting.
v Left Dial Hand: Points to ALM.
n Right Dial Hands:
Indicate the current alarm time setting in 24-hour
format.
ꢀꢁ
>
6
E-42
E-43
To change the alarm time setting
1. Use C to move the vLeft Dial Hand to ALM.
Adjusting the Home Positions
Strong magnetism or impact can cause the hands and/or date of the watch to be off.
2. Use D (+) and B (–) to change the alarm time setting.
If this happens, perform the applicable home position adjustment procedures in this
x Each press of either button will move the nRight Dial Hands one minute.
x Holding down D or B will start high-speed hand movement in the applicable
direction. To stop high-speed hand movement, press any button.
x The alarm always works based on the time kept in the Timekeeping Mode.
x The watch will return to the Timekeeping Mode automatically if you do not
perform any operation in the Alarm Mode for about two or three minutes.
section.
x Hand home position adjustment is not required if the time and day settings are
correct.
Note
Any time after you enter the home position adjustment mode in step 1 of the following
procedure, you can return to the Timekeeping Mode by pressing A. The watch also
will return to the Timekeeping Mode automatically if you do not perform any operation
for about two or three minutes in the home position adjustment mode. In either case,
any adjustments you made before the watch returned to the Timekeeping Mode will
be applied.
To turn the alarm on or off
In the Alarm Mode, press A to toggle the alarm on and off. The xSecond Hand will
indicate the current ON/OFF setting.
To stop the alarm
Press any button.
To adjust the home positions
1. Hold down C at least two seconds until the watch beeps twice and enters the
Timekeeping Mode.
E-44
E-45
3. After confirming that the xSecond Hand is at the proper home position, press C.
This will cause the zHour Hand, cMinute Hand, and bLower Dial Hand to
move to their home positions.
x The zHour Hand and cMinute Hand are at their proper home positions if
they both move to 12 o’clock. The bLower Dial Hand home position is 24. If
the hands are not at their proper home positions, use D (+) and B (–) to move
the zHour Hand and cMinute Hand so they point to 12. The bLower Dial
Hand will move along with zHour Hand movement, and cannot be adjusted
individually.
@
2. Hold down D for about three seconds until the watch
beeps.
x The watch is now in the home position adjustment
mode.
x The watch will exit the adjustment mode automatically
if you do not perform any operation for about two or
three minutes.
x First is xSecond Hand home position adjustment.
ꢀꢁ
x If the xSecond Hand moves to 12 o’clock, it is in the
correct home position. If it doesn’t, use D to move it
to 12 o’clock.
B
+
4. After confirming that the zHour Hand and cMinute
Hand are in their correct home positions, press C.
This will switch to nRight Dial Hand home position
adjustment.
x Each press of C in the home position adjustment mode will cycle through the
adjustment settings as shown below.
x The nRight Dial Hands are at their proper home
positions if they both move to 24. If the hands are not
positioned correctly, use D (+) and B (–) to move
them to 24.
xSecond
mDay
zHour/ cMinute/ b24-hour
nRight Dial Hands
vLeft Dial Hand
ꢀꢁ
*
6
E-46
E-47
>
6
5. After confirming that the nRight Dial Hands are in the
correct home position, press C. This will advance to
vLeft Dial Hand home position adjustment.
x The vLeft Dial Hand is in the correct home position if
it is pointing at 12 o’clock. If it isn’t, use D (+) and B
(–) to move it to 12 o’clock.
Troubleshooting
Hand Movement and Position
■ I lost track of what mode the watch is in.
Refer to “To select a mode” (page E-18). To return directly to the Timekeeping Mode
from any other mode, hold down C at least two seconds.
6. After confirming that the vLeft Dial Hand is in the
correct home position, press C. This will advance to
day home position adjustment.
x The mDay is in the correct home position if it
shows 1. If it doesn’t, use D (+) and B (–) to change
the day to 1.
ꢂ
■ The xSecond Hand is moving at two-second intervals.
■ All the watch’s hands are stopped at 12 o’clock and none of the buttons work.
Power may be low. Expose the watch to light until the xSecond Hand starts moving
normally, at one-second intervals (page E-8).
5
7. Press A to return to the Timekeeping Mode.
x The mDay moves to the current day, and then the zHour Hand and the
cMinute Hand move to the current time. Wait until everything stops moving.
E-48
E-49
Operation Guide 5181
■ The hands of the watch suddenly start moving at high speed, even when I do
■ The current time setting is off by hours.
Your Home City setting may be wrong. Check your Home City setting and correct it, if
necessary (page E-20).
not perform any operation.
This could be due to any one of the following causes. In all cases, the hand movement
does not indicate malfunction, and should stop shortly.
x The watch is recovering from a sleep state (page E-14).
x The watch is returning to the Timekeeping Mode automatically from the Alarm Mode
(page E-43).
■ The current time setting is off by one hour.
You may need to change your Home City’s STD (standard time)/DST (daylight saving
time) setting. Use the procedure under “To toggle the Home City time between
standard time and daylight saving time” (page E-22) to change the STD/DST setting.
■ Hands suddenly stop moving. Button operation also is disabled.
The watch may be in the power recovery mode (page E-12). Do not perform any
operation until the hands return to their normal positions (in about 15 minutes). The
hands should return to their correct positions when power recovers. To help power
recover, leave the watch in a location where it is exposed to light.
■ The hands and/or day indications are off.
This could indicate that the watch has been exposed to magnetism or strong impact,
which has caused problems with proper hand and day alignment. Adjust the watch’s
hand and day home position alignment (page E-45).
E-50
E-51
■ The xSecond Hand starts to move at one-second intervals, but then suddenly
returns to moving at two-second intervals.
The watch probably is not sufficiently charged yet. Continue keeping it exposed to
light.
World Time Mode
■ The World Time indicated by the nRight Dial Hands in the Timekeeping Mode
and World Time Mode is one hour off from the actual time in the selected
time zone.
The STD (standard time)/DST (daylight saving time) setting of the selected World
Time City may be wrong. Select the correct STD (standard time)/DST (daylight saving
time) setting (page E-39).
■ The World Time indicated by the nRight Dial Hands in the Timekeeping Mode
and World Time Mode is off.
Your Home City setting may be wrong. Check your Home City settings and correct
them, if necessary (page E-20).
Charging
■ The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 3 (page E-10). Continue
exposing the watch to light until the xSecond Hand starts moving normally (at one-
second intervals).
E-52
E-53
World Time: 29 cities (29 time zones) and Coordinated Universal Time
Other: Standard Time/Daylight Saving Time (summer time); Home City/World Time
City swapping
Alarm: Daily alarm
Other: Power Saving
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 6 months (no exposure to light after a full
charge and 10 seconds alarm beeper operation per day)
Specifications
Accuracy at normal temperature: 15 seconds a month
Timekeeping: Hour, minutes (hand moves every 10 seconds), seconds, 24-hour,
day, day of the week
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 29 city codes and Coordinated
Universal Time); Daylight Saving Time (summer time) / Standard Time
Stopwatch: Measuring capacity: 23:59'59.95"
Measuring unit: 1/20 second
Measuring mode: Elapsed time, split time
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments)
Other: Auto switching to elapsed time measurement (1-second units) when the end
of a countdown timer operation is reached
E-54
E-55
City Code
City
Tehran
Dubai
Kabul
Karachi
Delhi
UTC Offset/GMT Differential
City Code Table
TEHRAN
DUBAI
KABUL
(THR)
(DXB)
(KBL)
(KHI)
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
City Code
City
Pago Pago
Honolulu
Anchorage
Los Angeles
Denver
Chicago
New York
Santiago
UTC Offset/GMT Differential
PAGO PAGO
(PPG)
(HNL)
(ANC)
(LAX)
(DEN)
(CHI)
–11
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
HONOLULU
ANCHORAGE
LOS ANGELES
DENVER
CHICAGO
NEW YORK
SANTIAGO
RIO
KARACHI
DELHI
(DEL)
(DAC)
(RGN)
(BKK)
(HKG)
(TYO)
(ADL)
(SYD)
(NOU)
(WLG)
DHAKA
Dhaka
YANGON
BANGKOK
HONG KONG
TOKYO
ADELAIDE
SYDNEY
Yangon
Bangkok
Hong Kong
Tokyo
Adelaide
Sydney
Noumea
Wellington
(NYC)
(SCL)
Rio De Janeiro
Fernando de Noronha
Praia
F. DE NORONHA
PRAIA
(FEN)
(RAI)
NOUMEA
WELLINGTON
UTC
0
LONDON
PARIS
ATHENS
(LON)
(PAR)
(ATH)
(JED)
London
Paris
Athens
Jeddah
+1
+2
+3
xꢀ
xꢀ
ꢀBased on data as of July 2010.
ꢀThe rules governing global times (UTC offset and GMT differential) and summer
JEDDAH
time are determined by each individual country.
L-1
L-2
|