MA0702-EA
Operation Guide DQD-105
•
A sticker is affixed to the glass of this clock when you purchase it. Be sure to remove the sticker before using the clock.
ILLUSTRATION
• Depending on its model number, the appearance of your clock may differ somewhat from that shown in the
illustration.
3
4
6
Alarm Off
Snooze Alarm On
Current time (Hour, minutes, seconds)
DST indicator
Snooze on indicator
5
PM indicator
Antenna Icon
Date
(month – date)
Alarm on indicator
Day of the week
Wave OK indicator
1
2
GENERAL GUIDE
1SNOOZE/LIGHT button
• Press this button to illuminate the display for about four seconds.
• Pressing this button while the alarm is sounding stops the alarm.
2WAVE button
Press this button to receive the time calibration signal and adjust timekeeping.
3AUTO LIGHT button
Use this button to configure Auto Light settings.
4Alarm Time Set buttons
Use these buttons to change the alarm time or current time setting.
5SET button
Use this button when setting the current time.
7
6RESET button
Press this button to reset the clock after replacing its batteries.
7Alarm Mode selector
SNOOZE: Snooze alarm on
ALM ON: Alarm on
1
ALM OFF: Alarm off
8Batteries
2
8
1
Operation Guide DQD-105
USING THE ALARM
TO TURN AUTO LIGHT ON AND OFF
The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm
Mode selector (7) to select the snooze alarm feature.
1. While the Normal Timekeeping Screen is displayed, press the AUTO LIGHT button (3).
2. Within about five seconds, press the Alarm Time Set buttons (4) to toggle Auto Light on or off.
3. After the setting is the way you want, simply do not perform any key operation for about five seconds. The clock
will return to the Normal Timekeeping Screen automatically.
Setting the Alarm Time
Use the Alarm Time Set buttons (4) to set the alarm time.
Pressing the Alarm Time Set buttons (4) causes the alarm time to appear in place of the time on the display.
* A NIGHT LIGHT indicator (
) remains on the clock display while Auto Light is on.
3 4
Press to change the
alarm time setting (
Press to change the
alarm time setting (+).
—
).
• Holding down + or – changes the digits at high speed.
Turning the Alarm On and Off
Normal Timekeeping Screen
Use the Alarm Mode selector (7) on the side of the clock to turn the alarm on and off, and to select the snooze
feature.
Alarm Mode selector
SNOOZE
Description
The alarm sounds at the preset time for one minute, and seven
more times every five minutes thereafter. Even if you stop the
alarm sound by pressing the SNOOZE/LIGHT button (1), the
alarm operation is performed again five minutes later.
flashes on the display to indicate that the
snooze feature is activated.
( )
AUTO LIGHT button (3)
Five seconds
NIGHT LIGHT indicator (
)
• The indicator
ALM ON
( )
ALM OFF
Auto Light Off
Auto Light On
The alarm sounds at the preset time for one minute.
Alarm Time Set buttons (4)
The alarm does not sound.
• The light also turns on for the first five seconds that the alarm sounds.
• The alarm sound changes over four levels as it sounds.
Alarm Time Set buttons (4)
Stopping the Alarm
• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned
on, the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector (7) to ALM OFF.
USING THE LIGHT
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the
dark.
Important!
• Overuse of the light can shorten battery life.
AUTO LIGHT
• You can configure the Auto Light feature to illuminate the display of the clock at a specific time.
• The display will remain illuminate for six hours starting from the time you specify.
3
Operation Guide DQD-105
TO SPECIFY THE ILLUMINATION ON TIME
BATTERY REPLACEMENT
1. While the Normal Timekeeping Screen is displayed, press the AUTO LIGHT button (3).
2. Within about five seconds, use the Alarm Time Set buttons (4) to turn on Auto Light.
3. Within about five seconds, press the AUTO LIGHT button (3).
• This will cause the current Auto Light start time setting to appear on the display.
4. Within about five seconds, use the Alarm Time Set buttons (4) to change the Auto Light start time setting. You
can change the Auto Light start time in 10-minute increments.
5. After the setting is the way you want, simply do not perform any key operation for about five seconds. The clock
will return to the Normal Timekeeping Screen automatically.
* If you allow about five seconds to elapse without performing any operation during any of the above steps, the
clock will return to the Normal Timekeeping Screen automatically.
Replace batteries whenever the display of the clock becomes dim and difficult to read.
1. Open the battery compartment cover as shown in the illustration.
2. Remove all of the old batteries.
3. Load a full set of new batteries. Make sure that their positive (+) and negative (–) ends face in the correct
directions. If you load batteries incorrectly, they can burst and damage the clock.
4. Replace the battery compartment cover.
5. Press the RESET button (6). Be sure to press the RESET button (6) after replacing batteries.
Battery precautions
• Keep batteries out of the reach of small children. If a battery is swallowed accidentally, contact your physician
immediately.
Normal Timekeeping Screen
• Be sure to load the batteries with their positive (+) and negative (–) ends facing correctly.
• Never mix old and new batteries, or batteries of different brands.
• Never charge the batteries that come with the clock.
• Should batteries ever leak while in the clock, wipe out the fluid with a cloth, taking care not to let any get onto
your skin.
• Replace the batteries at least once a year, even if the current batteries are working properly.
• The batteries that come with the clock lose some of their power during transport and storage.
AUTO LIGHT button (3)
Five seconds
Auto Light Off
Auto Light On
Alarm Time Set buttons (4)
Alarm Time Set buttons (4)
After turning on Auto Light,
press the AUTO LIGHT button (3)
Current Illumination On Time Setting
Five seconds
Normal Timekeeping Screen
4
|