CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
mOUNTINg RECOmmENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FAN INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
CONTROL FEATURES:
inteli•touch operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
inteli•touch troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
reaD anD saVe these instructions
Safety and the proper operation of your Casablanca fan both require a thorough knowledge of the
product and proper installation; therefore, before attempting to install and operate your Casablanca
fan, read this owner’s manual completely and carefully. Retain this manual for future reference.
cauTion: To avoid possible electrical shock, make certain that electricity is turned off at
the circuit breaker or fuse box before attempting any installation procedure.
BEFOREYOU START
• All wiring must be in accordance with the National Electric Code ANSI/NFPA 70-1993 and the appropriate local electrical
codes. The National Electric Code requires proper grounding as a precaution against electrical shock. A qualified electri-
cian should be consulted if you are unsure.
• This fan is designed to be installed on an existing electrical outlet box. The outlet box must be UL Listed for ceiling fan
installations, if it is not, a new box must be installed. Casablanca extension poles are available for sloped or high ceiling
installations.
• This ceiling fan requires a grounded electrical supply of 120 VAC, 60 Hz and a minimum 15 amp circuit. The maximum
current requirement for the fan with light fixture is 3.8 amps. The fan uses about 1 amp or 100 watts. Maximum light
current is 2.8 amps or 340 watts of lighting.
• Where wire nuts are employed, be sure all bare wires are within the connectors. When installing the canopy hatch, make
sure all wires are within the canopy and that no wires are being pinched.
For best performance and for your warranty to be valid,
use only genuine Casablanca blades, light fixtures, and accessories.
NOTES
• The blades in each pack are matched for
equal weight to assure smooth fan operation.
If more than one fan is being installed, be
careful not to mix blades from different
cartons.
• Inspect the contents of your carton for
possible shipping or handling damage and
report any such damage directly to your
authorized Casablanca dealer.
• It is always a good idea to have an assistant
to help with the installation.
FUSE BOX
(remove fuse for The
circuiT you will be
working on)
18″
70″
84″
• When cleaning, painting, or working near
your fan, be very careful of the fan and
blades. Always turn the power OFF to the
ceiling fan before servicing it, working on
it, or replacing light bulbs.
CIRCUIT BREAKER
(Trip breaker for The
circuiT you will be
working on)
• Never insert anything into the path of the
fan blades while the fan is in operation.
• Never install a fan over a pool or spa.
• Never operate a fan that has been damaged in
any way. Contact Casablanca Fan Company by
calling 1-888-227-2178, or contact your local
authorized Casablanca dealer for assistance
in obtaining service.
pn 6343001 at1008
1
®
Vi c t o r i a n
INSTALLATION INSTRUCTIONS
Unpacking: Before assembling and installing your ceiling fan,
remove all parts from the shipping cartons and check them
against the parts listed here. Before discarding packaging
material, be certain that all parts have been removed.
noTe: Only one set of blade holders is supplied. Depend-
ing on the fan model and series they will be either the
Commodore Style, the Center Style, the Badge Style with
matching badges, or the Standard Style blade holder.
PERMA LOCk™ HARDWARE
•
ALLEN SET SCREw
DOwNROD & BALL
ASSEmBLy
1
⁄
4-20 x 1⁄4
”
3mm
allen Wrench
(pre-installeD)
FAN PREPARATION
imporTanT safeTy informaTion!
mOTOR
wIRES
before starting the installation of your ceiling fan, install the
threaDeD DoWnroD into the Motor coupling anD lock the asseMbly
gROUND
wIRE
prepare for fan installation as follows:
Step A. Route the wires from the motor through the
Perma Lock™ downrod and ball assembly.
•
DOwNROD
& BALL
ASSEmBLy
Tip: The downrod has a tapered thread
that is designed to lock completely when
correctly installed.
tapereD
threaD
Step B. Using the provided allen wrench, loosen the set screw
several turns to allow installation of the downrod. Thread the
downrod into the motor coupling until it stops turning, this
will take at least four and a half full turns.
ALLEN
SET SCREw
Step C. Securely tighten the set screw with the provided allen
wrench to ensure safe operation of your fan.
mOTOR
coupling
CAUTION: Failure to fully lock in the down-
rod before securely tightening the set screw
may cause the fan to separate from the
downrod during normal operation!
CEILING HARDWARE
addiTional hardware
21/4″ x 8-32 rounD heaD
SCREwS (2)
CROSSBAR mOUNT-
wIRE NUT (4)
1″ x 8-32 rounD
INg BRACKET
flat Washer (2)
heaD screWs (2)
GETTING STARTED
Installing a New Ceiling Fixture Outlet Box
Using Existing Ceiling Fixture Outlet Box
If you do not have an existing fixture located where you wish After turning the power OFF at its source (either circuit
to place your Casablanca fan, an approved ceiling fixture breaker or fuse box), lower the old fixture and disconnect
outlet box must be installed and wired.
the wiring. Check the ceiling fixture outlet box to be sure
that it is marked ‘Approved for ceiling fan mounting’. If it is
not, a new box must be installed.
warning: To reduce the risk of fire, electrical shock,
or personal injury, mount to outlet box marked ac-
ceptable for ceiling fan support using the mounting
hardware provided with the outlet box.
3
CROSSBAR MOUNTING BRACkET INSTALLATION
CEILINg FAN
approVeD
proceed with installation as follows:
Step 1. Route the wires from the ceiling outlet box through
the crossbar mounting bracket center hole. Attach the
bracket, with ground wire and ridges down, to the ceiling
fixture outlet box with the mounting hardware included with
the outlet box.
wIRINg BOX
CEILINg
wIRINg
Tighten the screws firmly by hand only, being careful not to
bend the bracket by over tightening.
RIDgE
SIDE
DOwN
CROSSBAR
mOUNTINg
BRACKET
FLAT
Washer
CAUTION: To reduce the risk of
personal injury, use only the
mounting hardware provided with
the approved outlet box to install
the crossbar mounting bracket.
gREEN
gROUND
wIRE
approVeD
OUTLET BOX
harDWare
CANOPY HARDWARE
canopy screW (4)
canopy lock Washer (4)
canopy
hatch
canopy
CANOPY INSTALLATION
Step 2. Attach the canopy to the crossbar mount-
ing bracket with three of the 8-32 x 21/4″ long
canopy screws and canopy lock washers.
Tighten the screw firmly by hand only.
CROSSBAR
mOUNTINg
BRACKET
noTe: On sloped ceilings, align the
canopy opening towards the top or
room peak.
canopy
canopy lock
Washer
canopy
SCREw
4
®
Vi c t o r i a n
HANGINGTHE FAN
Step 3. To hang the fan body in the
canopy, hold the fan body firmly and
insert the ball into the canopy open-
ing. Check that no wires were pinched.
Rotate the fan body until the slot in the
nylon ball fits into the pin opposite the
canopy opening.
cappeD
BLUE
D1-option
wIRE ON
BALL
noTe: Independent control of the
light fixture using a W-80 requires
an additional power wire run from
the wall switch to the fan. See Page
11 for wiring.
3-speeD only
for inDepenDent
W-80 light
CONTROL
SLOT
pin
CANOPY ELECTRICAL CONNECTIONS
wIRE NUT
Step 4a. Attach the fan wires to the ceiling fixture outlet
box wiring by twisting the bare ends of the wires together
and then securing with a wire nut. Test that the connection
is secure by pulling on the wire nut. Connect in this order:
pull chain or
W-40 connections
2 BLACK & BLUE
D1-option Wires
(Without W-80)
step 4b. pull chain or W-40 Wiring connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
• BLUE wire and BLACK power wire from fan to BLACK power
wire in ceiling outlet box. Secure with wire nut.
2 White Wires
3 gREEN wIRES
step 4c. W-80 Wiring connections
W-80 connections
• GREEN leads from mounting plate and fan to GROUND
conductor of power source. Secure with wire nut.
• WHITE wire from fan to white NEUTRAL wire in ceiling
fixture outlet box. Secure with wire nut.
BLUE & yELLOw
wIRES
• BLACK power wire from fan to RED wire from W-80 in ceil-
ing outlet box. Secure with wire nut.
• BLUE wire from fan to YELLOW wire from W-80 in ceiling
outlet box. Secure with wire nut.
BLACK & RED
wIRES
2 White Wires
3 gREEN wIRES
note: see page 7 for additional wiring information.
CANOPY HATCH INSTALLATION
Step 5. Tuck the wires into the canopy
with the wire nuts pointed upwards, so
that the WHITE and BLACK wires are on
opposite sides of the canopy and all wires
are clear of the canopy opening.
canopy
hatch
step 6. Install canopy hatch with the
last canopy screw and lock washer. To
do this, tilt the fan body away from the
hatch opening.
LOCK
Washer
canopy
Tighten the screws firmly by hand only,
SCREw
tilt the
FAN TO
INSTALL
LAST
canopy
SCREw
Step 7. Straighten the fan, then check
to ensure that there is no movement be-
tween the canopy and ceiling or Hang-Tru
ball and top support shaft.
5
BLADE HOLDERS & HARDWARE
BADgE STyLE
blaDe holDer screW
(2 per blaDe)
BLADE SCREw
(4 per blaDe)
BADgE
BADGE STYLE BLADE HOLDER & BLADE
Step 8. Badge Style
Attach the blades to the blade
holders by first pressing the
blade badge into the blade, then
installing the blade holder using
the four blade screws provided for
each blade.
BADgE STyLE
blaDe holDer
Hand tighten securely.
Install the assembled blade and
blade holder to the flywheel
(round holes) or direct drive
motor.
blaDe holDer screW
(2 per blaDe holDer)
Hand tighten securely.
BLADE
BADgE
BLADE
Repeat for each assembly.
Your fan is equipped with a flywheel
that allows for both 4 and 5 blade in-
stallation. The screw holes surrounded
by squares are for 4 blade installation,
while the screw holes in circles are for
5 blade installation as shown above.
6
Inteli•Touch®
R
INTELI•TOUCH INSTALLINGTHEW-32WALL CONTROL
The wall control installs in the same manner as an ordinary light switch, using an existing junction box and wiring. This
controller is designed to signal the fan microcomputer as well as perform normal switching operations. For this reason the
following precautions must be observed:
1. Use only the Casablanca W-32 wall control.
4. No other light fixtures or electrical appliances may be
2. Do not use any additional control with your Inteli-Touch
connected on the circuit controlled by the W-32 wall
fan (for example, dimmer, fan speed control, etc.).
3. Do not use more than one fan per wall control.
control.
INTELI•TOUCH SINGLEW-32 INSTALLATION
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
W-32 is used to describe either white (-11) or ivory finish.
1. Remove the screws and switch plate from the existing switch box.
2. Remove the screws holding the switch in the switch box.
3. Pull the existing switch from the switch box to expose the wire con-
nections.
4. Remove the two wires from the switch.
5. Connect the two wires just removed from the switch to the W-32
wall control black wire and black/white stripe wire. Secure these
connections with wire nuts.
6. Connect the green ground wire coming from the back of the W-32
control to the ground wire in the switch box. Secure the splice with
a wire nut.
7. Install the W-32 in the wall box with the two long screws pro-
vided.
8. Install the wall plate with the two color matched screws.
N0TE: If wall control operation is reversed (fan switch controls lights
and light switch controls fan) turn off the power at the breaker or
fuse panel, then swap the two W-32 black/white stripe wires.
INTELI•TOUCH DUALW-32 INSTALLATION
CAUTION! Ensure power is turned OFF at the breaker
or fuse panel before starting installation.
To control the fan and lights from two locations (a three-way
circuit), use 2 W-32 wall controls.
1. Remove the screws and switch plate from the existing
switch box and the screws holding the switch in the
switch box.
2. Pull the existing switch from the switch box to expose
the wire connections.
3. Determine which wire is connected to the common ter-
minal of the 3-way switch. (The terminal will be marked
on switch).
4. Remove the wire from the common terminal of the 3-way
switch. Connect this wire to the remaining black/white
striped wire on the W-32 control. Secure this splice with
a wire nut.
R
R
5. Remove the two remaining wires from the 3-way switch.
Connect one of these wires to a black wire on the W-32
control. Secure the splice with a wire nut. The remaining
wire is to be connected to the other black wire on the
W-32. Secure the splice with a wire nut.
6. Connect the green ground wire coming from the back of
the W-32 control to the ground wire in the switch box.
Secure the splice with a wire nut.
7. Install the W-32 in the wall box with the two long screws
provided.
8. Install the wall plate with the two short color-matched
screws provided.
9. Installation of the second W-32 control is identical.
Repeat steps 1 through 7.
NOTE: If wall control operation is reversed (fan switch controls lights and
light switch controls fan) turn off the power at the breaker or fuse panel,
then swap the two W-32 black/white stripe wires.
7
Inteli•Touch®
The POWER button is normally left in the on position. Always turn the
power off during cleaning or servicing the fan and during thunderstorms. It
is also used to exit or enter additional programs.
R
INTELI•TOUCH OPERATION POWER
POWER must be left on to retain a previously set fan speed or light
level.
INTELI•TOUCH OPERATION SPEED CONTROL
There are six individual speed settings for the fan; each speed is indicated
by an audible tone of increasing pitch.
FAN CONTROL
To select the desired fan speed:
ON - OFF
A momentary press
of the FAN button
FAN
1. With fan off, press and hold the button labeled
. The fan blades
will start rotating at the slowest speed, and will increase in steps.
2. Release the button when the desired speed is reached.
The fan speed is now in memory and will automatically come on at the same
TO CHANGE SPEED
Press and hold FAN
button longer than
one second
FAN
speed each time the
button is used. To maintain this level of speed,
FAN
turn the fan on by pressing
less than one second. To lower speed,
FAN
turn fan off, then on by pressing and holding the
desired speed is reached. When the fan is on, you may increase the speed by
button until the
FAN
pressing and holding the
then release it.
button until the desired speed is reached,
INTELI•TOUCH REVERSING AIRFLOW
•
The direction of airflow can be changed from downward to
R
Note: A four-toned signal indi-
cates the command was accepted
by the fan. A few seconds later
the fan will slow to a stop and
then reverse direction.
upward or from upward to downward.
To reverse the airflow:
FAN
1. Make sure the
is on.
button.
REVERSE
2. Press the
INTELI•TOUCH LIGHT
LIGHT
To turn the lights off and on, press and release the
than one second.
button for less
LIGHT CONTROL
To vary the light brightness:
R
ON - OFF
A momentary press of
the LIGHT button
LIGHT
1. With lights off, press and hold the
button. After one second the
lights come on at their lowest level and gradually become brighter.
2. Release the button when the desired brightness level is reached.
The brightness level is now in the fan memory and will automatically come
TO CHANGE BRIGHT-
NESS
PRESS AND HOLD
LIGHT BUTTON
LONGERTHAN ONE
SECOND
LIGHT
on at the same brightness the next time the
maintain this level of brightness, press the
button is used. To
button for less than
LIGHT
one second. To lower the brightness, turn the lights off, then press and hold
LIGHT
the
button until the desired brightness level is reached. When the
light is on, you may increase the brightness level by pressing and holding
LIGHT
the
button until the desired level is reached, then release it.
AUTOMATIC DEMONSTRATION PROGRAM
A multi-tone signal will verify the start of the test program which
proceeds as follows:
• Lights slowly increase to full intensity.
• Fan accelerates to speed three with audio tones.
• Light dims to half intensity.
• Fan accelerates to full speed with audio tones.
• Fan reverses at full speed with audio tones.
• Fan operates at full speed.
• Fan power is reversed with audio tones.
• Fan turns off with audio tones (blades coast for a short time).
• Lights turn off.
Programmed into every Inteli-Touch Series fan is an Automatic
Demonstration Program. It can be used to fully demonstrate and
test the operation of the fan.
To enter the demonstration program:
POWER
1. Turn POWER off for at least three seconds. This will clear
the fan memory ready for programming.
POWER
2. Turn Pon.
3. Immediately operate the buttons in the following sequence:
LIGHT
LIGHT
FAN
FAN
FAN
+
+
+
+
The complete cycle lasts slightly over one minute. It will continue
POWER
to repeat until the POWER is turned off for more than three
seconds, cancelling the program.
8
Inteli•Touch®
R
INTELI•TOUCH OPERATION LIGHT-MINDER PROGRAM
The Light-Minder program automatically turns OFF the fan mounted lights after
two hours.
To enter the Light-Minder Program:
POWER
1. Turn the POWEROFF for at least three seconds.
POWER
2. Turn the
ON.
3. Immediately operate the buttons in the following sequence:
LIGHT
FAN
FAN
LIGHT
+
+
+
4. A series of tones indicates this command has been accepted.
The fan and light will operate normally using the buttons to turn them on and off.
But, if the lights are left on, they will automatically shut off after two hours. To
cancel the Light-Minder Program, turn the POWER off for three seconds.
INTELI•TOUCH OPERATION SAFE-EXIT PROGRAM
The Safe-Exit Program gives you about thirty seconds of light when you turn
the lights off, enabling you to exit your home before the lights go out.
To enter the Safe-Exit Program:
POWER
1. Turn the POWE off for at least three seconds.
POWER
2. Turn the POWE on.
3. Immediately operate the buttons in the following sequence:
FAN
FAN
LIGHT
LIGHT
+
+
+
After you hear the confirming audio
tones from the fan - immediately press
LIGHT
4. The lights will blink to indicate this command has been accepted.
The lights will stay on for twenty seconds and then begin to dim. After a total
of thirty seconds has elapsed, the lights will be off completely. To cancel the
Note: Both Light-Minder and Safe-Exit
programs can run at the same time,
however the dimmer cannot be used,
the light may only be turned ON/OFF.
POWER
Safe-Exit Program, turn the Poff for three seconds.
INTELI•TOUCH OPERATION HOME-SAFE® PROGRAM
The Home-Safe Program makes an unoccupied home appear occupied by turning
the lights on and off at random times.
To enter the Home-Safe Program:
POWER
1. Turn the off for at least three seconds.
POWER
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
LIGHT
LIGHT
FAN
FAN
+
+
+
4. A tone and flashing light indicate this command has been accepted.
This program overrides all manual control of lights and fan. The lights will now be
automatically cycled on and off in a controlled sequence as follows: On 1 hour, off
1/2 hour, on 2 hours, off 1 hour, on 1/2 hour then off 2 hours.
This seven hour pattern will repeat continuously so that a different pattern of
lighting is seen each day of the week.
To cancel the Home-Safe Program, turn the off for three seconds.
POWER
INTELI•TOUCH OPERATION FAN-MINDER® PROGRAM
The Fan-Minder feature will add to your comfort when used in the bedroom. The program reduces the
speed of the fan each two-hour interval to compensate for the cooling night air.
To enter the Fan-Minder Program:
POWER
1. Turn the POWE off for at least three seconds.
POWER
2. Turn the on.
3. Immediately operate the buttons in the following sequence:
LIGHT
LIGHT
FAN
FAN
+
+
+
4. The fan controller will respond with three descending tones. A timer is now initiated and the fan
will reduce one speed for each two-hour interval. The fan will not, however, descend below the
second lowest speed.
POWER
To cancel the Fan-Minder Program, turn the E off for three seconds. You may increase the fan
FAN
speed by pressing and holding the
button until the desired speed is reached, then release
it. The fan will again reduce one speed for each 2 hour interval.
9
Inteli•Touch®
TROUBLESHOOTING
Before Requesting Service: Please follow this troubleshooting guide be-
fore contacting your dealer for assistance.
Caring for Finishes: For cleaning, a soft brush or lint-free cloth Never Lubricate this Fan!
should be used to prevent scratching the finish. A vacuum cleaner The precision motor at the heart of your Casablanca fan features
brush nozzle can remove heavier dust. Surface smudges or an ac- sealed bearings that are lubricated for life. Do not attempt to oil
cumulation of dirt and dust can easily be removed by using a mild the motor.
detergent and slightly dampened soft cloth. An antistatic agent Changing Light Bulbs
may be used, but never use abrasive cleaning agents. These will Be sure to turn power to the fan OFF at the wall switch or circuit
damage the finish. Painted and high-gloss blades may be cleaned breaker before changing light bulbs. Replace bulbs with same type as
in the same manner.
removed from the fixture. Each fan is rated for a maximum TOTAL
Blades: Wood finish blades should be cleaned with a furniture wattage of lighting.
polishing cloth. Occasionally, a light coat of furniture polish may Exceeding the rated maximum allowable wattage for the fan will
be applied for added protection and beauty.
burn out the fan electronics module and void the warranty.
PROBLEM
INTELI•TOUCH
POSSIBLE REMEDIES
NO FAN OR LIGHT
Check main circuit fuses, curcuit breakers, or wall switch position. Check all wire connections, making
sure the power is turned off during this inspection.
FANWOBBLES OR SHAkES
Be sure canopy pin is properly set into the slot on the ball
EXCESSIVELY
Check the screws holding the blade holders to the fan motor. Tighten as necessary.
Check the angle of the blades to make sure that a blade holder has not been bent during installation.
FAN NOISY DURING
OPERATION
Check and tighten light fixture retaining screws, glass shade screws and/or the light bulb(s).
Tighten canopy screws and mounting plate assembly.
Tighten the blade to bladeholder screws and blade holders to flywheel.
Make sure all screws in the motor housing are snug, but not overly tight.
Check that the wire nuts inside the canopy and switch housing are not touching the metal parts or
have fallen off the wire splices. Tighten or adjust as necessary.
BREAK-IN PERIOD
Let fan run at high speed for two (2) hours
DOES NOT RUN ON
LOW SPEED
If new, “break-in” may be required - run at higher speed for several days
LIGHTS FLASH OR BLINK DURING OPERATION OFW-32WALL CONTROLS/FAN MAY ROTATE OR MAKE
AUDIBLETONES DURING OPERATION OFTHEW-32WALL CONTROLS: Normal operation.
WHEN AC POWER ISTURNED ON FORTHE FIRSTTIME,THE LIGHTS OPERATE NORMALLY, BUTW-32WALL
CONTROL OPERATION IS REVERSED: FAN BUTTON OPERATESTHE LIGHTS; LIGHT BUTTON OPERATES
THE FAN: Reverse the 2 black and white striped wire connections.
FAN OR LIGHTS APPEARTO OPERATE BYTHEMSELVES (CHANGING SPEED OR INTENSITY),WALL CON-
TROL OPERATION IS INTERMITTENT: Check AC supply for irregularities, (noise spikes, fluctuations, or failure); or circuit
board assembly.
10
®
Vi c t o r i a n
PRODUCT SPECIFICATIONS
®
Model Name:
Victorian®
63XXT
Motor:
XLP-2000
Model Number:
Blade Span:
Blade Iron Pitch:
No. of Blades:
Technology:
46" or 54"
15°
5
Dimensions:
A =11.5"
B =13.5"
C = 3"
D = 13"
E =5.6"
Inteli•Touch® W-32
NOTE: Dimension B
includes light fixture
and glass.
Airflow*:
6,250 cfm
Electricity Use*:
Airflow Efficiency*:
108 watts
51.1 cfm/watt
Weight:
23 lbs.
* Performance data is for fan only. No lighting wattage is included.
Measurements taken with 21" basic blades.
11
|