R
Vehicle Security
User’s Manual
Model: PLUS-6800
For Technical Assistance, please call (800) 638-3600,
Remote Control Transmitters
The LCD screen on the 2-way remote control displays graphic icons. It provides visual information
on any trigger of the sensors and around the clock surveillance of your vehicle, as well as
displaying the present status of the system.
2-Way LCD Remote
LCD Display Icons
1-Way Remote
LCD Remote Icons
Door Lock
Vehicles Doors are Locked
Timer Control Start
Automatic Engine Start (Timed)
Power Save Mode
Saves The Battery Power when
Transmitter is not in Use
Door Unlock
Vehicles Doors are Unlocked
Armed Mode
Security System is Armed
Vibrate Mode
Vibrates when Security System is
Triggered
Valet Mode
Security System is in Valet Mode
Low Battery
Replace the Transmitter Battery
Remote Transmission
Transmitting a Signal
Shock Sensor
Shock Sensor Triggered (Zone 4)
In-Range Indicator
You are within Remote Control Range
Ignition
Engine Starting by Remote Control
Door Triggered
Doors are Opened (Zone 3)
Ignition
Trigger On Ignition Switch (Zone 5)
Trunk/Hood Triggered
Trunk/Hood are Open (Zone 2)
Engine Running
Vehicle Engine is Running
Warn Away
Shock Sensor Triggered (Zone 1)
Driver Paging / Lost and Found
Someone is Paging you from the Vehicle
Second Vehicle
Communicate with a Second Vehicle’s
Security System
System Trigger/Panic
Alerts that the System has been
Triggered
3
LCD Remote Control Transmitter Operation
Transmitter Button
System Function
Remark
Lock Doors & Arms System
Arm and Delete the 2-Stage
Shock Sensor
Press Twice within 3 Seconds
-
-
Press within 3 Seconds.
For 1-Way Transmitter
Arm System and
Hidden Alarm Function
Press
-
Car Locator
Panic Function
Upon Armed
Press and Hold for 3 seconds.
Ignition in “OFF” Position
Silent Arming/Disarming
Active Anti-Car Jacking Mode
+
+
Ignition in “ON” Position,
Press and Hold for 2 Seconds
Unlock Doors & Disarm System
Two Steps Door Unlock and
Disarm System
-
-
Press Twice within 3 Seconds
Press and Hold for 2 Seconds
For 1-Way Transmitter
Press
Trunk Release - Channel 3
Passive Arming Bypass
While the System
is in “Disarmed” Mode.
For 1-Way Transmitter
Press
-
Activate or Turn Off
the Remote Start
-
Press Twice within 3 Seconds
+
Turbo Timer Mode
For 1-Way Transmitter
Timer Control Output - Channel 4
+
Press
+
4
Programming the LCD Transmitter
Vibration/Melody Mode
This mode is useful when you are in a noisy place and it is difficult to hear the beep from the
transmitter. While in the Vibration/Melody Mode, the transmitter will vibrate if your security
system has been activated.
1. Press and hold the
and buttons at the same time until one long beep is
heard. Programming has now been entered.
2. Within 5 seconds, press the
button to select the vibration or Melody Mode.
The icon will be displayed on the screen to show the remote transmitter is in
Vibration Mode.
3. To exit the Programming Mode, take no action for five seconds. The remote
control will generate two long beeps to indicate Programming Mode has been
exited.
Power Save Mode
While in the Power Save Mode, the LCD remote transmitter will “Sleep” until a
button is pushed, extending the life of battery. When Power Save Mode is “OFF”,
the remote control will wake up periodically to check for messages from the
security system.
1. Press and hold the
and
buttons at the same time until one long beep is
heard. Programming has now been entered.
2. Within 5 seconds, press the
button to toggle between “ON” or “OFF”. The
remote will beep once for “ON”, and twice for “OFF”. When Power Save Mode is “ON”, the
icon on the LCD screen indicates entry into Power Save Mode.
3. To exit Programming Mode, take no action for five seconds. The remote control will generate
two long beeps indicating Programming Mode has been exited.
Screen Lamp On
Press the
button once, and the LCD screen lamp will turn on for 5 seconds.
System Status Check
To check the system’s present status through the LCD screen, press the
transmitter button first, then within 3 seconds press
and buttons at the
same time. The response will be one melody sound, and the LCD screen will be
illuminated. Note: If no response is received, then you are out of range.
Clear the Flash Icon and Melody Sound
Press the
button first, then within 3 seconds press the
and buttons at the same time.
These steps will clear the flash icon and melody sound on the LCD transmitter.
Stop the Trigger Melody Sound
While triggering the alarm the LCD screen will alert the user through a melody sound and a
flashing trigger icon. Press any button on the LCD transmitter to stop melody sound only, and the
remote control will not send a command to the system.
5
Programming the LCD Transmitter
Press Buttons at the Same Time: Then Press Button Within:
System Function
Switching to 2nd Vehicle
or Returning to 1st
Vehicle Operation
+
5 Sec.
+
+
Melody / Vibration Mode
Power Save Mode
5 Sec.
5 Sec.
LCD Screen Lamp
Turns On for Five Seconds
+
+
System Status Check
3 Sec.
3 Sec.
Clear the Flash Icon
and Melody Sound
Battery Replacement
The LCD remote control is powered by a 1.5 Volt
AAA Alkaline battery. When the power of the
battery weakens the battery icon
will be
displayed on the screen. When the old battery is
replaced with a new one, there will be a beep to
indicate the power is up. To replace the battery,
follow the steps in the illustration at left.
Note: Press the
button two times when the
battery compartment is empty, then insert the
new battery.
Interference
The transmission range may decrease if the system encounters interference from tall structures or
stronger radio frequencies such as high-voltage power lines.
LED Indicator
LED
Function
OFF
System is Disarmed
Slow Flashing
Fast Flashing
On Solid
System is Armed
System in Automatic Arming
System in Valet Mode
2 Flashes - Pause
3 Flashes - Pause
4 Flashes - Pause
5 Flashes - Pause
Zone 2, Trigger on Trunk/Hook
Zone 3, Trigger on Door Switch
Zone 4, Trigger on Shock Sensor
Zone 5, Trigger on Ignition Switch
6
Parking Lights
Flash
Function
1 Flash
System is Armed
System is Disarmed
Disarmed / Triggered
Car Locator
2 Flashes
3 Flashes
12 Flashes
Constant On or Flashing Under Remote Start
Chirp Indicators
Chirp
Function
1 Chirp
2 Chirps
3 Chirps
4 Chirps
6 Chirps
System is Armed
System is Disarmed
Ajar Warning
Disarm / Triggered
Car Locator
System Characteristics
Parking
Light
Siren/Horn
LED
Doors
Locking
Unlocking
Starter
Dome Light
Disabled
(Option)
1. Arming
1 or 3 Chirps
1 Flash
Slow Flash
2 or 3
Flashes
Turns on for
30 Seconds
2. Disarming 2 or 4 Chirps
Disabled
(Option)
3. Trigger
4. Panic
Alarming
Alarming
Alarming
6 Chirps
Flashes
Flashes
Slow Flash
Flashes
Flashes
Flashes
5.Car
Jacking
Disabled
(Option)
Flashes
6.Car
Locator
12 Flashes
Locking
7
Manual Arming: Lock & Arm
1. Press the
button on the transmitter.
2. The siren will chirp once and parking lights will flash once indicating that the system is now
armed. The vehicle doors will lock upon arming when interfaced with the security system.
System Armed
Door Ajar
Trunk/Hood Ajar
Ajar Warning:
If the siren sounds 3 chirps,
then you have left a door,
trunk, or hood lid ajar.
Silent Arming/Disarming
Press the transmitter and button at the same time to arm or disarm your security system. No
chirp sound will be heard. The arm/disarm confirmation will be through the vehicle’s parking
lights only.
Shock Sensor Bypass
Press the button on the transmitter two times within 3 seconds. This will arm the security
system and bypass the shock sensor. The system will chirp one additional time to confirm the
sensor Bypass Mode was activated. The sensor bypass feature is programmed to activate for one
arming cycle only. The security system will return to normal operation during the next arming
cycle.
Hidden Alarm Function
Press the
button first, within 3 seconds press the
button to activate the hidden alarm
function. The security system will arm, but the siren / horn will be silenced even if the sensor is
triggered in the armed status.
Automatic Arming
Manual arming/disarming is controlling your security system via the remote transmitter. This
security system is equipped with an optional Automatic Arming feature which allows the security
system to arm 30 seconds after the last door is closed. Operation is as follows:
1. Turn the ignition to the “OFF” position and exit the vehicle.
2. After all entrances are closed, the security system LED will flash fast for 30 seconds. If you
reopen any Door, Hood, Trunk the security system LED will stop flashing. It will begin flashing
again once the vehicle’s entrances are closed.
3. After the 30-second timer has elapsed, the security system will automatically “ARM”. The
siren/horn will chirp once, and the parking lights will flash once.
Automatic Arming with Automatic Door Locking (Programmable)
The vehicle doors will automatically lock after the passive arming cycle has been completed.
8
Automatic Arming Bypass
While the system is in Disarmed Mode, press the
button twice. The horn/siren will respond
with one chirp and the LED will turn “ON”. The security system will remain in this mode for as
long as you wish. To exit this mode press the or buttons and the system will return to normal
status.
Manual Disarming Unlock & Disarm
1. Press the button on the transmitter.
2. The siren will chirp twice and parking lights will flash twice indicating that the system is now
disarmed. The vehicle door will unlock and the dome light will turn on for 30 seconds upon
disarming when interfaced with the security system.
System Disarmed
Doors Triggered
Trunk/Hood Triggered Shock Sensor Triggered Ignition Triggered
Tamper Disarming
If the security system is triggered upon disarm, the siren will chirp 4 times and the parking lights
will flash 3 times.
Pathway Illumination
This feature turns the parking lights “ON” for 30 seconds upon a unlock signal and for 10 seconds
upon the lock signal.
Two Step Door Unlock
This feature will independently unlock the driver’s door only when disarming the security system.
Pushing the button a second time within 3 seconds will unlock the other doors.
Automatic Rearm
If this feature is selected, the security system will automatically rearm itself within 60 seconds
after disarming with the remote transmitter. Automatic rearm will cancel if any door is opened
before the 60 second timer is up.
Disarming without a Transmitter
The override function may be used if the remote transmitter is lost or inoperative. Override can be
done without password/pin number (this is the factory default setting).
1. Enter the vehicle and turn the ignition switch to “ON” position (alarm will sound).
2. Within 10 seconds push and release the valet switch. The alarm will stop sounding and enter
the Disarm Mode. You can now start and operate the vehicle normally.
9
Valet Mode (System in Disarm or Valet Mode)
The valet switch allows you to temporarily bypass all alarm functions eliminating the need to hand
your transmitter to parking attendants or garage mechanics. When the system is in Valet Mode, all
alarm functions and remote start functions are bypassed. However, the remote panic feature and
remote door locks remain operational. To use the Valet Mode, the system must first be disarmed
either by using your remote transmitter, or by operating the manual override sequence.
Remote Door Lock
Remote Door Unlock
Enter Valet Mode
1. In the Disarmed Mode, turn the ignition to “ON”
position.
2. Push and hold the valet switch for 2 seconds
until the LED turns on solid. The LED will remain
on solid as long as the unit is in the Valet Mode.
Exit Valet Mode
1. To return to normal operation, turn “ON” ignition.
2. Push and hold valet switch for 2 seconds. The LED will turn off, indicating the system has now
exited the Valet Mode.
Car Locator
While in the Armed Mode, press the button to activate car locator function. The siren/horn will
chirp 6 times and the parking lights will flash 12 times to help you locate your car.
Panic Function
The transmitter can be used as a remote panic switch to manually trigger the alarm system in
case of an emergency.
1. Press and hold the button for 3 seconds to enter the Panic Mode (horn/siren will start to
sound and parking lights will flash).
2. While in Panic Mode the transmitter and buttons can be used to lock and unlock the door
(if that option is installed). However, if the
button is pressed, the vehicle’s starter disable
device (when installed) will be disabled, allowing the vehicle to start.
3. To turn off the panic function, press and hold the or button again for 3 seconds.
Note: If any transmitter buttons other than or button is pressed the panic function will be
turned off.
4. If the panic function is not turned off by the transmitter, it will turn off and reset itself after 30
seconds.
10
Anti-Car Jacking
Warning: This security system has a car jacking feature. Its default setting is “OFF”. So be sure to
enable this feature if you feel it is needed.
Active Anti-Car Jacking
1. Press and hold the transmitter
and
buttons at the same time for 2 seconds while the
vehicle’s ignition is “ON”. The parking lights will turn on for 1.5 seconds to indicate the system
has entered the Anti-Car Jacking Mode.
2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the door
is opened and closed while the ignition is “ON”.
Passive Anti-Car Jacking
1. Turn the ignition switch to the “ON” position, and the system will enter the Anti-Car Jacking
Mode.
2. Once the system is armed in the Anti-Car Jacking Mode, the system will trigger when the door
is opened and closed while the ignition is “ON”.
Trigger the Anti-Car Jacking Mode
A. 50 seconds after the system has been triggered. The siren will start chirping for 15 seconds.
B. During this 15 second period of chirping, you can push the valet switch once to turn off the car
jacking feature.
C. 65 seconds after the system has been triggered. The siren starts sounding and the parking
lights start flashing.
D. 90 seconds after the system has been triggered:
1. The siren will still be sounding and the parking lights flashing.
2. The starter disable will activate to prevent the vehicle from starting.
3. Anti-Car Jacking Mode will remain active until the override procedure is performed or the
vehicle's battery power is exhausted.
Override the System to Turn Off Anti-Car Jacking
Turn the ignition switch from OFF to ON, and within 10 seconds push the valet switch. The siren
will stop sounding and the security system is now disarmed.
Note: If you use password pin code to double protect the vehicle, you will need to use it to
completely disarm the system.
11
Dome Light Supervision
The Security System has a unique feature for using your vehicle’s dome light:
1. Upon disarming the vehicles security system, the interior dome light will remain on for 30
seconds.
2. If the security system is triggered, the dome light will flash for the same duration as the
horn/siren.
Note: Turn “ON” the ignition switch or arm the system to turn off the dome light.
Ignition Controlled Door Locks
If the vehicles door locks have been interfaced with the security system, the system will
automatically lock the doors when the ignition is turned “ON”, or unlock the doors when ignition
key is turned “OFF”.
Trunk Release Output (Channel 3)
Press and hold the
button for two seconds to activate the trunk release (Channel 3 output)
and/or any other devices connected.
Timer Control Output (Channel 4)
Press and hold the
and
button at the same time to activate the Channel 4 output. Channel 4
is user programmable timer output. You may program the built-in timer to send a ground signal
for any time duration from 1 second to 120 seconds. For example, this timer output may be used
to turn on the headlights, power window or sunroof (Factory defaults setting at momentary
output.)
Driver Paging / Lost and Found (For LCD transmitter only)
Driver Paging / Lost and Found is useful the event that someone wants to page
the driver of the parked vehicle, or someone cannot find the LCD transmitter.
With the ignition switch in the “OFF” position, press and hold the valet switch for
2 seconds to page the driver. One chirp shall be emitted and the paging melody
continues sounding from the LCD transmitter and
will flash on the screen.
Out-of-Range Indication
If the Out-of-Range Indication feature is activated the system will automatically check the range
every 30 minutes after armed.
1. If the user is within the range, the icon will display on the LCD screen.
2. If user is out of range, the
beeps 5 times.
icon will disappear from the LCD screen and the transmitter will
Note: Activating this feature will decrease the life expectancy of battery.
Power-On Memory
This security system is equipped with circuitry that will allow the unit to remember its alarm state
if the power is lost and then reconnected.
12
REMOTE START OPERATION
Activate
Remote Start
Remote Start Your Vehicle Using the Remote Transmitter
1. Press the button twice on the transmitter.
2. The parking lights will turn on indicating the remote start has received the
signal (A melody sound from your LCD transmitter and the
on the LCD screen to confirm the remote start was activated.)
3. The engine will start in approximately 5 seconds.
icon will flash
4. Once the engine is running, the parking lights will turn on again after a few
seconds, and the climate controls will activate and adjust the vehicles interior
temperature to your preset setting. While the vehicle is running, the
will flash on the LCD screen indicating the count down timer based on the 5, 10,
20 or 30 minute run-time setup by the installer.
icon
Engine
Running
5. The vehicle will run for 5 to 30 minute cycles and automatically shut down.
(When the unit shuts off, the count down timer will turn off and the
transmitter will play a melody).
Note: The Remote Start Unit will not start the vehicle if any one of the following
conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. Move the optional remote start enable toggle switch to OFF position (if installed).
4. The vehicle is in a gear other then “Park” or “Neutral”.
Safe Start (Child Safety Mode)
If the default method of remote starting has been reprogrammed to Child Safety Mode Operation,
to remote start your vehicle is to press the
Note: To turn off the remote start press the
and the
and the
buttons at the same time.
buttons at the same time.
To Operate the Vehicle After the Vehicle has been Started by Remote Start
1. Insert the ignition key, and turn it to the “ON” position, NOT the “START” position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the “ON” position, the engine will
automatically shut off.
Temporary Stop Feature
This feature allows the vehicle to remain running after the key has been removed from the
ignition. It is useful on occasions when you wish to exit and lock the vehicle for a short period of
time, but keep the engine running allowing the climate controls to stay on.
1. Before turning the engine off with the ignition key, press the
three times indicating the feature has been activated.
button twice. The LED will flash
2. Turn the ignition key to the “OFF” position (the engine will stay running).
3. The engine will run until the pre-programmed time has elapsed or shutdown input is received.
13
Turbo Timer Mode
After arriving at your destination, Turbo Timer keeps the engine running for a programmable time
period of 1, 3 or 5 minutes. This allows the engine’s turbo charger time to conveniently cool down
after you have left the vehicle.
To Activate:
1. While the engine is running, set the emergency brake and place the transmission into "Park".
2. Before turning off the engine, press and release and buttons at the same time. The parking
lights will flash indicating the remote start has entered Turbo Timer Mode.
3. Remove the ignition key and the engine will keep running.
4. Exit and secure the vehicle. The engine continues running until the pre-programmed time has
elapsed.
Timer Start
Important! Timer Start should be used only in open areas. Never start or leave a vehicle running in
an enclosed area such as a garage or carport.
This unit can be programmed to auto-start and run the engine every 2 or 3 hours (3 hours is the
default setting). The engine will run for the programmed run time and then shut down. This
feature is designed to prevent the engine from freezing in cold climates.
A Maximum of Six Auto-Start Cycles can Occur.
Enter Timer Start:
1. Press the button twice to remote start the vehicle.
2. As soon as the parking lights have turned on or are flashing, press the
button once. Then
press and hold the
times and the
button. The parking light will flash 3 times, the siren or horn will chirp 3
icon will appear on the LCD display. The vehicle is now
programmed to start every 3 hours.
3. Press the brake pedal to shut off the engine.
Exit Timer Start:
1. Make sure the remote start system is not operating the engine.
2. Turn the ignition “ON”. The LED and parking lights will flash 4 times. The horn
chirps 4 times. The vehicle is no longer programmed to Timer Start
automatically.
Or
1. Press the button twice to remote start the vehicle.
2. As soon as the parking lights have turned on or flashing, press the button once. Then press
and hold the button. The parking lights will flash 4 times. The siren or horn chirps 4 times.
The vehicle is no longer programmed to Timer Start automatically.
14
Turn Off Remote Start
When the engine is running by remote start and you wish to shut it off, follow
these steps:
1. While in Remote Start Mode, press the
transmitter.
button twice on the remote
2. Move the optional remote start toggle switch to the “OFF” position (if
installed).
3. Press the vehicle’s brake pedal, the engine will stop running and the parking
lights will turn off to indicate the engine has been shut off.
Shut Down Input for Remote Starter
If any of the following conditions exist while the system is operating, the engine will not start or will
shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. The hand brake is released (for Standard Transmission vehicles only).
4. Engine is over-revved (Tachometer Checking Type only).
5. The preprogrammed run time (5/10/20/30 minutes) has elapsed.
6. Press the
button twice on the remote transmitter under Remote Start Mode.
7. Move the optional remote start enable toggle switch to “OFF” position (if installed).
8. The vehicle refused to start running after 3 unsuccessful attempts.
Disabling The Remote Start System (If Installed)
The disabling the Remote Start System feature allows your system’s remote start unit to be
temporarily disabled, which prevents the vehicle from being remote started accidentally. This is
useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start,
move the optional remote start enable toggle switch to the “OFF” position.
15
Second Carbine Security System Operation
If your transmitters have been programmed to a second Carbine security system, follow the steps
below.
For LCD Remote Control Transmitter:
Second Vehicle Operation: While the
can remote control and communicate with a second vehicle security system.
1. Press and hold and buttons at the same time until one long beep is heard.
icon is displayed on the LCD screen, you
Programming Mode has now been entered.
Note: No action for five seconds will generate two long beeps indicating the
Programming Mode has been exited.
2. Within 5 seconds, press and hold the
button until two beeping sounds are
heard and the
3. While the
icon is displayed on the LCD screen indicating second car operation.
is displayed, press any button on the transmitter to control the second vehicle’s
security system or alarm function (arm/disarm/trunk/remote start).
Note: Button functions are the same for the second car as they are for the first car.
Return to First Car Operation
1. Press and hold
and buttons at the same time until one long beep is heard.
Programming Mode has now been entered.
Note: No action for five seconds will generate two long beeps indicating the
Programming Mode has been exited.
2. Within 5 seconds, press and hold the
button until one beeping sounds are
heard and the
operation.
icon is not displayed on the LCD screen indicating first car
16
Replacement Parts and Accessories
TRANSMITTERS
DESCRIPTION
MODEL #
$ PRICE
2-Way LCD Remote for
PLUS-6800 Security System
CA-RFLCD1
139.95 ea.
1-Way Remote for
PLUS-6800 Security System
CA-RC6HF
59.95 ea.
BATTERIES
1.5 Volt AAA Alkaline Battery commonly
found in grocery stores, hardware stores,
etc.
CR2032 - 3 Volt Lithium Battery (1 pc.)
Models:
Radio Shack: #23-162
Duracell: #DL2032
Eveready: #ECR2032
Panasonic: # CR2032
17
Parts and Accessories Order Form
Mail to: Magnadyne Corporation
ATTN: Consumer Parts Sales
P.O. Box 5365
Credit Card or Money Order Only
(Sorry No Cash, C.O.D. or personal checks accepted)
Call: (310) 884-7777 Fax: (310) 637-9542
Carson, CA 90749-5365
SHIP TO: (No P.O. Boxes)
LAST NAME
FIRST NAME
INITIAL
STREET ADDRESS
ADDITIONAL ADDRESS
ADDITIONAL ADDRESS
CITY
STATE
ZIP CODE
DAY TIME PHONE NUMBER
CREDIT CARD INFORMATION
VISA
MC
CREDIT CARD N0.
CARD HOLDER’S LAST NAME
STREET ADDRESS
CITY
EXPIRATION DATE
FIRST NAME
INITIAL
STATE
QTY.
ZIP CODE
PART #
DESCRIPTION
PRICE EACH
TOTAL
Shipping and Handling
Sales Subtotal = ________ . ______
Up to $20.00
20.01 to 30.00
30.01 to 45.00
45.01 to 70.00
Over 70.01
$5.00
5.95
6.50
6.95
7.95
California Residents Add Sales Tax = ________ . ______
Shipping and Handling (See Chart) = ________ . ______
TOTAL = ________ . ______
On regular orders please allow 4-5 weeks for delivery.
Please give a shipping address where this order may be delivered between the hours of 9 am and 5 pm weekdays.
If UPS is unable to deliver, your order will be returned and additional shipping charges will be required.
18
Limited Lifetime Warranty
Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original
purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found
defective in materials or workmanship, when properly connected and operating on the correct
power requirements designated for the specific product. This warranty and Magnadyne Corporation
or its authorized agents obligations, hereunder do not apply where the product was: damaged while
in the possession of the consumer, subjected to unreasonable or unintended use, not reasonably
maintained, utilized in commercial or industrial operation, or serviced by anyone other than
Magnadyne Corporation or its authorized agent, or where the warning seal on the product is broken
or the power plugs or wires are detached from the unit. Magnadyne Corporation or any of its
authorized agents do not assume any labor costs for the removal and reinstallation of any product
found to be defective, or the cost of transportation to Magnadyne Corporation or its authorized
agents. Such costs are the sole responsibility of the purchaser.
This warranty does not cover the cabinet, appearance items, normal wear and tear or accessories
used in connection with the product resulting from improper installation, alteration, accident,
misuse, abuse or acts of nature.
This Limited Life Time Warranty applies only to the receiver section of the security system. Neither
the siren, transmitters, wire harness or any accessory item added to or used with a Remote Mobile
security system are covered by this Limited Life Time Warranty. Sirens, transmitters, wire harness
or any accessory item are covered by our standard 12 month limited warranty.
Magnadyne Corporation or its authorized agents shall not be liable to anyone for consequential
or incidental damages or claims that may arise due to failure of product to operate properly
except those accorded by law. Magnadyne's or its authorized agents liability to the repair,
replacement of the product as stated above if all conditions of the warranty are met. No
expressed warranty or implied warranty is given except those set forth herein. Magnadyne does
not warrant or guarantee against break in damage or the theft of the vehicle in part or whole, or
against the loss or damage to the contents of any vehicle in which a security system is
installed. Magnadyne security systems are only a deterrent against possible theft.
This warranty extends only to the original purchaser of the product and for the vehicle in which it
was originally installed. This warranty is not transferable or assignable to any person or vehicle.
Defective merchandise should be returned to the original point of purchase or secondly to
Magnadyne Corporation, 1111 W. Victoria Street, Compton, CA 90220. A return authorization must
be obtained before sending, or merchandise may be refused.
19
R
PLUS-6800-UM 4-28-06 Rev. A
© Copyright 2006 Magnadyne Corporation
|