Assembly Instructions and Parts List
PW1686
Please read and save these instructions. Read carefully before attempting to assem-
ble, install, operate or maintain the product described. Protect yourself and others by
observing all safety information. Failure to comply with instructions could result in
personal injury and/or property damage! Retain instructions for future reference.
Electric Pressure
Washer
NOTE: REFER TO PRODUCT MANUAL
FOR ALL SAFETY INSTRUCTIONS
Specifications
Max Pressure
with
Motor
Power
Maximum
Inlet
Cleaning Standard Maximum (Single
Water
Unit
Model
Power
Lance
Capacity
Phase)
Voltage
120V
Temp. Weight
PW1686
2640
1650 psi 1.6 GPM 14 Amps
100˚F
38 lbs.
Assembly Instructions
1. Attach detergent suction tube to
hose barb on detergent tank and
put cap on detergent tank (Figure
1).
3
3
4
2. Slide accessory storage bracket onto
back of pressure washer (Figure 1).
3. Slide cord holder and lance storage
collar onto side of pressure washer
(Figure 1).
1
2
4. Align handle on back of pressure
washer and attach using screws pro-
vided (Figure 1).
Figure 1
5. Assemble one wheel to axle and
slide through back of pressure wash-
er and detergent tank (Figure 2).
Figure 2
For parts, product & service information
IN463600AV 12/03
© 2003 Campbell Hausfeld
visit www.chpower.com
Assembly Instructions and Parts List
Assembly Instructions (Continued)
PW1686
6. Assemble second wheel to axle
(Figure 3).
7. Attach hose holder with screws pro-
vided (Figure 4).
8. Attach lance storage holder with
screw provided (FIgure 5).
9. Align hub cap locking tabs with
wheels and press into place (Figure
5).
Figure 3
Figure 5
Figure 4
2
Assembly Instructions and Parts List
PW1686
Garden Hose Connection
! IMPORTANT !
GARDEN HOSE CONNECTION
INSTRUCTIONS
1. Attach nipple adapter to inlet fitting
on the unit (this may already be
attached to the pump).
2. Attach quick connect fitting to gar-
den hose.
3. Pull side “A” of quick connect fitting
toward garden hose and push onto
nipple adapter.
This pressure washer is equipped with a
microswitch sensitive to water flow. This
Instant Start/Stop switch (ISS) senses
water flow in the pump. When the trig-
ger is released, water stops flowing
through the pump. The ISS then auto-
matically turns the motor off to protect
pump from overheating.
OPERATION
1. Pull trigger on gun.
4. Push side “A” of quick connect fitting
towards nipple adapter and release.
2. Turn the “ON/OFF” switch to “ON”.
3. Release trigger. The pressure washer
motor will stop running.
"A"
Quick Connect Fitting
4. To spray again, pull trigger and motor
and pump will restart.
Garden Hose
Note: Occasionally the motor may run
for a short time to bring fresh, cool
water into the pump even if trigger is
released. This is part of normal opera-
tion and will not damage the unit.
Nipple
Adapter
Figure 6 - Garden Hose Connection
Always turn the
“ON/OFF” switch to “OFF”
!
CAUTION
Power Cord
then trigger gun to release hose pres-
sure before unplugging power cord.
1. Plug the power cord into a ground-
ed 120V outlet and press the reset
button as shown in Figure 7.
Risk of equipment dam-
!
CAUTION
age. Always make sure
the “ON/OFF” switch on the unit is
“OFF” and unit is unplugged prior to
storage.
2. THIS MUST BE DONE EACH TIME THE
UNIT IS PLUGGED IN AN OUTLET.
Reset
Risk of Injection.
!
WARNING
Unit will start spraying
when trigger is squeezed if on/off
switch is in “ON” position. Always
point gun in safe direction.
Call 1-800-330-0712
for Technical Service
Figure 7 - Grounded plug/reset button
3
Assembly Instructions and Parts List
PW1686
System Connection
1. Insert lance into the gun and turn
clockwise to positive stop as shown in
Figure 8.
4. Connect garden hose as explained
under Garden Hose Connection
Instructions.
5. Plug the power cord into a grounded
120V outlet, that is on a dedicated
circuit.
6. Turn water on.
7. Depress and hold the trigger on the
gun for one minute to release pres-
sure and remove any air trapped in
the system.
8. Turn the “ON/OFF” switch to the
“ON” position.
Figure 8 - Gun/Lance Connection
2. Ensure that the power switch is in the
“OFF” position.
3. Attach the high pressure hose and
gun assembly to the unit.
NOTE: REFER TO PRODUCT MANUAL
FOR OPERATING INSTRUCTIONS
Gun
On/Off
Switch
OUTLET
13 mm
High
Pressure
Hose
INLET
Garden
Hose
Figure 9
4
Assembly Instructions and Parts List
PW1686
Please provide following information:
-Model number
Replacement Parts List
-Serial number (if any)
-Part description and number as
shown in parts list
For Replacement Parts,
Call 1-800-330-0712
Address parts correspondence to:
The Campbell Group / Parts Dept.
100 Production Drive
8
Harrison, OH 45030 U.S.A.
9
20
4
1
10
11
9
9
19
16
5
3
2
12
13
14
6
7
18
17
15
Ref.
No.
Part
Number
Description
Qty.
1
Adjustable pressure lance
Turbo lance
PM271080SV
PM022621AV
PM243600AV
PM037201SJ
PM022100AV
PM020600SV
PM008500AV
PM271000SV
PM271010SV
PM271020SV
PM271030SV
PM271040SV
PM270050SV
PM060000SV
PM271050SV
PM066300SV
PM066301SV
PM271060SV
PM271070SV
PM232200SV
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
3
Hose
4
Gun
5
Nipple adapter
Quick connect fitting
Tip cleaner
6
7
8
Handle
9
Hardware pack
Lance storage collar
Accessories storage bracket
Lance storage holder
Hose holder
10
11
12
13
14
15
16
17
18
19
20
Detergent tank cap
Detergent tank
Wheel cover
Wheel
Axle
Cord holder
O-ring
5
|