LTC9316/00P
Security Systems
Installation Manual
Standard Pole
EN
LTC9316/00P
Instruction Manual
Installation
3
EN
7.778
24"
6"
4X
O
1.000
BASED ON A 11.00" B.C.
6"
36"
32"
24"
13.0007.778
4.000
24"
O
11.000
4.000
O
3.000
13.000
24"
32"
36"
Figure 3 Anchor Bolt Dimensions
PV4 Anchor jig (if applicable)
NOTE: Prepare the concrete per manufacturer's
directions. The concrete must have a compressive
!
8"
8"
strength of 3000 psi, and must be fabricated following
ACI318-89 requirements. Allow the concrete
foundation to cure thoroughly before proceeding with
the installation.
12"
12"
32"
36"
Reinforcement bars (12)
Figure 4 View of Concrete Foundation
Figure 2 Reinforcement Bars
3. FOR ANCHOR BOLT INSTALLATIONS:
4.2 Installation
Pour concrete per manufacturer's directions, making sure that
the wiring conduit is in the center of the pad. See Figure 3
(next page) for dimensions of the bolt pattern and suspend
appropriate bolts in the concrete around the wiring conduit.
Leave 2" to 3" of the Bolts protruding above the pad. If you are
using leveling nuts, leave 4" to 6" protruding.
NOTE: Be sure that the pole is oriented properly, with the
carriage.
!
1. Place the pole on the pad with the holes on the Base Plate
aligned with the bolts of the anchor bolts or anchor jig
(Figure 5).
2.
Remove the access opening plates at the bottom and top.
Bosch Security Systems 10 October 2003
LTC9316/00P
Instruction Manual
Installation
4
EN
Access opening plates
Bolts or
anchor jig
Figure 7 Lifting the Pole into Position
CAUTION: Pull all slack in the wiring as you lift the pole into
position to keep from pinching and possible damage.
Pad
Figure 5 Placement of Pole on Pad
6. Ensure that the pole is vertical on all sides. Use a
bubble level or plumb bob to check.
3. Insert the wiring into the 3" diameter hole in the base of the
pole. Be sure all slack is pulled completely through.
7. Secure the pole to the pad with fasteners (Figure 8).
4. Insert connecting wiring into the bottom access opening, run
through the pole up to the top access opening. Insert the end
rough the housing connecting hole. Close the top access
opening and make necessary wiring connections at the bottom
access opening (Figure 6).
Nut
Lock Washer
Top access opening
Flat Washer
Figure 8 Securing the Pole to the Pad
®
4.3 Mounting the AutoDome
1. Align the holes of the AutoDome adapter plate with the
holes on the mounting plate at the top of the pole
(Figure 9).
Figure 6 Connecting Wiring Through Pole
5. Slowly lift the pole into the upright position, aligning
the holes of the Base Plate with the Bolts in the concrete
pad (FigurBosch Security Systems10 October 2003e 7).
Bosch Security Systems 10 October 2003
Mount the LTC 9540/xx
Wall Bracket Using
These Holes
Adapter Plate
Figure 9 Aligning Adapter Plate with Mounting Plate
Figure 11 Mounting the LTC 9540/xx Wall Bracket
2. Attach the LTC 9540/xx Wall Bracket adapter plate, using
the provided hex head nuts and bolts, flat washers, and
lockwashers (see Figure 10).
5
SPARE PARTS
Part No.
LTC9316AP
Description
LTC 9540/xx Wall Arm
Adapter Plate
Lockwashers
Flat Washers
5/16-18 Nuts
Figure 10 Attaching the Adapter Plate
3. Attach the LTC 9540/xx Wall Bracket to the adapter plate
using recommended 8 mm (5/16-inch) bolts/studs (refer to
the LTC 9540/xx Installation Instructions). Bolts should be
secured with nuts, washers, and lockwashers.
Bosch Security Systems, Inc.
850 Greenfield Road
Robert Bosch GmbH
Geschäftsbereich
Bosch Security Systems B.V.
P.O. Box 80002
Lancaster, PA 17601 EE.UU.
Tel: 800-326-3270
Postfach 10 60 50
70049 Stuttgart
5600 JB Eindhoven
The Netherlands
Fax: 1-717-735-6560
Telefax (0711) 811-12 34
Tele +31 40 27 80000
© 2005 Bosch Security Systems GmbH
3935 890 38012 28
June
Data subject to change without notice.
|