WARNING
Marine Electrical Products
These instructions are intended to provide assistance with the
installation of this product, and are not a substitute for a more
comprehensive understanding of electrical systems. We strongly
recommend that a competent electrical professional perform the
installation of this product.
If either the switch front or back is to be exposed to water it must be
protected with a waterproof shield.
The switch must not be installed in explosive environments such as
gasoline engine rooms or battery compartments as the switches
are not ignition proof.
The vessel’s shore power cord must be disconnected form shoreside
power before installing this electrical switch.
If an inverter is installed on the vessel its power leads must be
disconnected at the battery before the panel installation. Be aware that
many inverters have a “sleep mode” in which their voltage potential
may not be detectable with measuring equipment.
If an AC Generator is installed aboard it must be stopped and rendered
inoperable before the switch is installed.
Verify that no other AC or DC source is connected to the vessel’s
wiring before the switch is installed.
AC Rotary Switch
2 Positions + OFF, 2 Pole
9009/9011
Features
• Switches 2 - 120V AC Sources or 2 - 230V AC Sources
• Compact solution when circuit protection is provided elsewhere
• Allows connecting one of two different AC sources to one circuit
• Heavy duty industrial rated switches
• Intuitive function - One handed operation
• UL listed switches
Specifications
Amperage Rating: PN 9009 is rated for 32 amp maximum service
PN 9011 is rated for 65 amp maximum service
Voltage Rating:
600 Volts AC Maximum
Maximum Wire Size: PN 9009
PN 9011
10 AWG
6 AWG
Minimum Wire Size: PN 9009
PN 9011
Terminal Recommended Torque:
PN 9009
14 AWG
12 AWG
Guarantee:
Blue Sea Systems stands behind its products for as long as you own
12 lb-in.
40 lb-in.
Inches
1.890 x 1.890
2.520 x 2.520
1.913
For customer service, call 800-222-7617.
PN 9011
Millimeters
48.00 x 48.00
64.00 x 64.00
48.60
Overall Dimensions: PN 9009
PN 9011
Mounting Depth:
PN 9009
PN 9011
2.807
71.30
Maximum Panel Thickness:
0.157
4.00
Blue Sea Systems Inc.
425 Sequoia Drive
Bellingham, WA 98226 USA
Phone (360) 738-8230
Fax (360) 734-4195
6670 Rev 002
Installation
The switch provides switching, but does not provide circuit protection.
It is not a substitute for a main circuit breaker.
1. Disconnect all AC and DC power
Disconnect all AC power originating on or off the vessel. This includes
inverters, generators, shore power attachments and any other device
capable of supplying AC power to the ship’s circuits.
Wire sizing chart
Use the wire sizing chart below to determine the proper branch and
feed circuit wire sizes.
Disconnect the main positive DC cable from all batteries to eliminate
the possibility of a short circuit and to disable the inverter while
installing the switch.
Allowable Amperage of Conductors
2. Select mounting location and cut opening
Select a mounting location which is protected from water on the front
and back of the switch and is not in an area where flammable vapors
from propane, gasoline or lead acid batteries accumulate. AC rotary
switches are not ignition protected and may ignite such vapors.
Using the template provided, drill the mounting surface where the
switch is to be mounted. The mounting surface maximum thickness is
0.157” (4.00mm). Do not yet fasten the switch to the mounting surface.
3. Install source 1, source 2 and output wires
Install the feed wires from AC Shore Power and AC Generator. Install
the output wires. Refer to the wire sizing chart to select the minimum
wire size. Connect the black AC hot, white AC neutral and green AC
safety ground as shown in the illustration. To avoid excess wire
temperatures when cooling may be limited, we recommend using at
least 12 gauge wire for 30A and 8 gauge wire for 50A.
Note: This chart assumes wire with 105°C insulation rating
and no more than 2 conductors are bundled.
Not suitable for sizing flexible shore power cords.
4. Testing
It is very important that the wiring be connected according to the
diagram. The line and neutral from each source must be paired
together and not connected such that the switch selects line from one
source and neutral from another. Verify the connections and see that
each connection is securely tightened, including the terminals for the
jumpers installed on the switch where no wires are attached.
Do not confuse the neutral current carrying wires (sometimes called
ground) with the green normally non-current carrying wires (sometimes
called grounding). These two wires must be connected only at the
source of power, nowhere else.
It is possible to verify the connections using an ohmmeter before power
is applied. These procedures take a little time, but are recommended,
especially if some elements of a previous installation might not have
A double pole circuit breaker must be installed within 10 feet of the
shore power inlet, ahead of this switch. The measurement is made
along the conductors.
been properly labeled or followed the expected color codes.
Page 1 of 3
Installation (continued)
Wiring Diagram
AC Rotary Selector Switch
0.197"
PN 9009 / PN 9011
Ø
5mm
0.394-0.590"
10.00-15.00mm
4 PLACES
Ø
0.197"
0.315-0.590"
8.00-15.00mm
Ø
Ø
5mm
4 PLACES
1.890"
48.00mm
1.417"
36.00mm
1.417"
36.00mm
1.890"
48.00mm
Panel Mounting
Panel Mounting
Hole Pattern
Hole Pattern
PN 9009
PN 9011
Panel Mounting
Assembly
6670 Rev 002
Page 3 of 3
|