FR
EN
DE
IT
ES
PT
EL
PW1300 C
NL
DA
NO
FI
SV
CS
PL
SL
SK
LT
BG
RU
HU
RO
TR
HR
LV
ET
UK
cod. 90968 - GX
3
E3
E1
C3
B4
A1-A2-A3
B2
C2
B1
B5
C1
B6
B3
D
1
4
1
2
3
4
5
Ø13
6
2
5
E
3
D
H
1
I
2
H
H
4
6
E
5
1 ÷ 25 m
2 x 1,5 mm2
25 ÷ 50 m
2 x 2,5 mm2
Volt
230
S
L1
N
Z1
T
M
1~
S = Switch
Z1 = Capacitor suppressor
T = Thermal protection
M = Motor
S1 = Pressure switch
C
NO
NC
S1
I
English
11
SAFETY INSTRUCTIONS
before doing work on the appliance, rEMovE the plug.
ac c i d E n t a l s t a r t -u p h a z a r d
1
2.2.4
2.2.5
2.2.6
1.1
The appliance you have purchased is a technologically advanced
product designed by one of the leading European manufacturers
of high pressure pumps. To obtain the best performance from your
unit, read this booklet carefully and follow the instructions each
time you use the it. We congratulate you on your choice and wish
you successful operation.
before pressing the trigger, grip the gun firmly to
counteract the recoil. in j u r y h a z a r d
CoMpLY WiTh the requirements of the local water supply
company. According to Din 1988, the appliance may only
be connected to the mains drinking water supply if a backflow
preventer valve with drain facility is installed in the supply hose.
co n t a m i n a t i o n h a z a r d
SAFETY RULES
2
Maintenance and/or repair of electrical components MUsT
be carried out by qualified staff. ac c i d E n t h a z a r d
2.2.7
2.2.8
2.2.9
2.1
SAFETY “MUST NOTS”
Do noT use the appliance with
inflammable or toxic liquids, or
2.1.1
DisChArgE residual pressure before disconnecting the
unit hose. in j u r y h a z a r d
any products which are not compatible with the correct operation
of the appliance. Ex p l o s i o n o r p o i s o n i n g h a z a r d
before using the appliance, ChECK every time that the
screws are fully tightened and that there are no broken or
worn parts. ac c i d E n t h a z a r d
Do noT direct the water jet towards people or
animals. in j u r y h a z a r d
2.1.2
2.1.3
onLY UsE detergents which will
not corrode the coating materials
of the high pressure hose/electrical cable. Ex p l o s i o n a n d E l E c t r i c
s h o c k h a z a r d
2.2.10
2.2.11
Do noT direct the water jet towards the unit
itself, electrical parts or towards other electrical
equipment. El E c t r i c s h o c k h a z a r d
Do noT use the appliance outdoors in case of rain. sh o r t
c i r c u i t h a z a r d
2.1.4
2.1.5
2.1.6
2.1.7
2.1.8
2.1.9
2.1.10
EnsUrE that all people or animals keep a minimum
distance of 16 yd. (15m) away. in j u r y h a z a r d
Do noT allow children or incompetent persons to use the
appliance. in j u r y h a z a r d
Do noT touch the plug and/or socket with wet
hands. El E c t r i c s h o c k h a z a r d
Do noT use the appliance if the electrical cable is
damaged. El E c t r i c s h o c k a n d s h o r t c i r c u i t h a z a r d
Do noT use the appliance if the high pressure
hose is damaged. Ex p l o s i o n h a z a r d
Do noT jam the trigger in the operating position. ac c i d E n t
h a z a r d
Check that the data plates are affixed to the appliance, if
not, inform your dealer. Units without plates must noT
be used as they are unidentifiable and potentially dangerous.
ac c i d E n t h a z a r d
Do noT tamper with or alter the calibration of the
safety valve. Ex p l o s i o n h a z a r d
2.1.11
2.1.12
2.1.13
2.1.14
Do noT alter the original diameter of the spray head
nozzle. ha z a r d o u s a l t E r a t i o n o f o p E r a t i n g p E r f o r m a n c E
Do noT leave the appliance unattended. ac c i d E n t h a z a r d
Do noT move the appliance by pulling on the
ELECTRICAL CAbLE. sh o r t c i r c u i t h a z a r d
Make sure that cars do not drive over the high pressure hose.
2.1.15
2.2
SAFETY “MUSTS”
All electrical conductors MUsT bE proTECTED against the
water jet. sh o r t c i r c u i t h a z a r d
2.2.1
The appliance MUsT onLY bE ConnECTED to an
adequate power supply in compliance with all
applicable regulations. El E c t r i c s h o c k h a z a r d
2.2.2
• Use of
a
safety residual current circuit-breaker (R.C.C.B.) will
provide additional protection for the operator (30 mA).
The high pressure may cause
2.2.3
materials to bounce off surfaces
at speed; therefore protective clothing and safety goggles MUsT
bE Worn. in j u r y h a z a r d
12
English
b2 Lance
GENERAL INFORMATION (FIG.1)
3
b3 gun with safety catch
b4 power supply cable with plug
b5 high pressure hose
3.1 Use of the manual
This manual forms an integral part of the appliance and should be
EN
kept for future reference. please read it carefully before installing/
using the unit. if the appliance is sold, the seller must pass on this
manual to the new owner along with the appliance.
b6 Detergent tank (on models with this feature)
4.4.1
Accessories (where applicable – see fig.1).
C1 nozzle cleaning tool
C2 rotating nozzle kit
C3 handle
3.2 Delivery
The appliance is delivered partially assembled in a cardboard box.
The supply package is illustrated in fig.1.
C4 brush
C5 hose reel
3.2.1
Documentation supplied with the appliance
A1 Use and maintenance manual
A2 safety instructions
4.5 Safety devices
Caution - Danger!
A3 Declaration of conformity
Do not tamper with or adjust the safety valve set-
3.3 Disposing of packaging
ting.
The packaging materials are not environmental pollutants but must
still be recycled or disposed of in compliance with the relevant
legislation in the country of use.
-
Safety valve and pressure limiting valve.
The safety valve is also a pressure limiting valve. When the gun
trigger is released, the valve opens and the water recirculates
through the pump inlet.
3.4 Safety signs
Comply with the instructions provided by the safety signs fitted to
the appliance.
-
Safety catch (D): prevents accidental spraying of water.
Check that they are present and legible; otherwise, fit replacements
in the original positions.
E1 sign – indicates that the appliance must not be disposed of as
municipal waste; it may be handed in to the dealer on purchase of a
new appliance. The appliance's electrical and electronic parts must
not be reused for improper uses since they contain substances
which constitute health hazards.
INSTALLATION (FIG.2)
5.1 Assembly
5
Caution - Danger!
All installation and assembly operations must be
performed with the appliance disconnected from the mains
power supply.
The assembly sequence is illustrated in fig.2.
3.4.1
Symbols
E2 symbol – indicates that the appliance is intended for
professional use, i.e. for experienced people informed
about the relative technical, regulatory and legislative
aspects and capable of performing the operations neces-
sary for the use and maintenance of the appliance.
E3 symbol – Indicates that the appliance is intended for
non-professional (domestic) use.
5.2 Assembling the rotating nozzle
(For models with this feature)
The rotating nozzle kit delivers greater washing power.
5.3 Electrical connection
Caution - Danger!
Check that the electrical supply voltage and frequen-
cy (V-Hz) correspond to those specified on the appliance
data plate (fig.2). The appliance should only be connected
to a mains power supply equipped with an adequate earth
TECHNICAL INFORMATION (FIG.1)
4.1 Envisaged use
4
connection and
a
differential security breaker (30 mA)
to cut off the electricity supply in the instance of a short
circuit.
This appliance has been designed for individual use for the cleaning
of vehicles, machines, boats, masonry, etc, to remove stubborn dirt
using clean water and biodegradable chemical detergents.
vehicle engines may be washed only if the dirty water is disposed of
as per regulations in force.
Intake water temperature: see data plate on the appliance.
Intake water pressure: below 10 bar.
5.3.1
Use of extension cables
Use cables featuring “IPX5” protection level.
The cross-section of the extension cable should be pro-
portionate to its length; the longer it is, the greater its
cross-section should be. See table I.
-
-
-
Operating ambient temperature: above 0°C.
5.4 Water supply connection
The appliance is compliant with the EN 60335-2-79/A1 standard.
Caution - Danger!
Only clean or filtered water should be used for intake.
4.2 Operator
The delivery of the water intake tap should be equal to that
of pump capacity.
place the appliance as close to the water supply system as possible.
The symbol on the front cover identifies the appliance’s intended
operator (professional or non-professional).
4.3 Improper use
5.4.1
Connection points
Use by unskilled persons or those who have not read and under-
stood the instructions in the manual is forbidden.
The introduction of inflammable, explosive and toxic liquids into the
appliance is prohibited.
l
Water outlet (OUTLET)
Water inlet with filter (INLET)
n
5.4.2
Connection to the mains water supply
Use of the appliance in
atmosphere is forbidden.
a
potentially inflammable or explosive
The appliance can be connected directly to the mains
drinking water supply only if the supply hose is fitted with
a backflow preventer valve as per current regulations in
force. Make sure that the hose is at least Ø 13 mm and
that it is reinforced.
The use of non-original spare parts and any other spare parts not
specifically intended for the model in question is prohibited.
All modifications to the appliance are prohibited. Any modifications
made to the appliance shall render the Declaration of Conformity
null and void and relieve the manufacturer of all liability under civil
and criminal law.
4.4 Main components
b1 Adjustable spray nozzle
English
13
7.4 Restarting
1) Release the safety catch (D).
ADJUSTMENT INFORMATION (FIG.3)
6
6.1 Adjusting the spray nozzle (for models with this feature)
Water flow is adjusted by regulating the nozzle (E).
2) Depress the gun trigger and discharge the residual air inside
the hoses.
EN
6.2 Adjusting the detergent (on models with this feature)
Detergent flow is adjusted using the regulator (F).
3) Set the starter device on (ON/1).
7.5 Storage
6.3 Adjusting the detergent pressure
1) Switch the appliance off (OFF/0).
2) Remove the plug from the socket.
3) Turn off the water supply tap.
set the adjustable nozzle on " " to deliver detergent at the correct
pressure (on models with this feature).
6.4 Adjusting the pressure (on models with this feature)
The regulator (G) is used to adjust the working pressure. The pres-
sure is shown on the pressure gauge (where fitted).
4) Discharge the residual pressure from the gun until all the water
has come out of the nozzle.
5) Drain the detergent tank.
6) Engage the gun safety catch (D).
INFORMATION ON USE OF THE APPLIANCE (FIG.4)
7
7.6 Refilling and using detergent
When using detergent, the adjustable nozzle must be set on
7.1 Controls
"
" (on models with this feature).
-
Starter device (H).
Fill the tank with highly degradable detergent.
Set the starter switch on (ON/1) to:
7.7 Recommended cleaning procedure
a) start the motor (in models without TSS device);
b) set the motor ready to start (in models with TSS device).
if there is a pilot light on the starter device, it should light up.
If the “low/high” settings are available, use them as follows:
Low : low pressure washing
High : high pressure washing
Set the starter device switch on (OFF/0) to shut down the applian-
ce.
Dissolve dirt by applying the detergent mixed with water to the
surface while still dry.
When dealing with vertical surfaces work from the bottom upwards.
Leave the detergent to act for 1-2 minutes but do not allow the
surface to dry. starting from the bottom, use the high pressure jet
at a minimum distance of 30 cm. Do not allow the rinse water to run
onto unwashed surfaces.
if there is a pilot light on the starter device, it should go out.
MAINTENANCE (FIG.5)
Any maintenance operations not covered by this chapter should be
carried out by an Authorized sales and service Centre.
8
-
Water jet control lever (I).
Caution - Danger!
During operation the appliance must be positioned
as shown in fig. 4 on a sturdy, stable surface.
7.2 Start-up
Caution - Danger!
Always disconnect the plug from the power socket
before carrying out any work on the appliance.
Caution - Danger!
8.1 Cleaning the nozzle
before starting up the appliance check that the water
supply hose is connected properly; use of the appliance
without water will damage it; do not cover the ventilation
grilles when the appliance is in use.
1) Disconnect the lance from the nozzle.
2) Remove any dirt deposits from the nozzle hole using the tool
(C1).
8.2 Cleaning the filter
On three-phase models for professional use, at first use start the
appliance for a very short time to check that the motor is running
in the correct direction. If the motor fan is turning anti-clockwise,
exchange two of the three phase wires (L1, L2, L3) in the electrical
plug.
1) Turn on the water supply tap fully.
2) Release the safety catch (D).
Clean the suction filter (L) and the detergent filter after every 50
hours of operation.
8.3 Unjamming the motor (on models with this feature)
in case of lengthy stoppages, limescale sediments may cause the
motor to seize. To unjam the motor, turn the drive shaft with
tool (M).
a
3) Depress the gun trigger for a few seconds and start up the appli-
ance using the starter device (ON/1).
TSS models - In TSS models with automatic delivery flow cut-off
system:
8.4 End-of-season storage
Treat the appliance with non-corrosive, non-toxic antifreeze before
storing it away for winter.
-
when the gun trigger is released the dynamic pressure automati-
cally cuts out the motor (see fig.4);
-
when the gun trigger is depressed the automatic drop in pres-
sure starts the motor and the pressure is restored after a very
slight delay;
-
if the TSS is to function correctly all gun releasing and depress-
ing operations must be performed at intervals of less than 4-5
seconds.
To prevent damage to the appliance, when running do not
stop the water jet for more than 10 minutes at a time.
7.3 Stopping the appliance
1) Set the starter device switch on (OFF/0).
2) Depress the gun trigger and discharge the residual pressure
inside the hoses.
3) Engage the gun safety catch (D).
14
English
TROUbLESHOOTING
9
EN
Problem
Possible causes
Remedy
nozzle worn
replace nozzle
Water filter fouled
Clean filter (fig.5)
Water supply pressure low
Air being sucked into system
Turn on water supply tap fully
Check tightness of hose fittings
switch off the appliance and keep depressing and releas-
ing the gun trigger until the water comes out in a steady
flow. switch the appliance back on again.
pump does not reach working
pressure
Air in pump
Adjustable nozzle not positioned correctly
Water intake from external tank
intake water too hot
Turn the adjustable nozzle (E) (+) (fig.3)
Connect appliance to the mains water supply
reduce temperature
pressure drops during use
nozzle clogged
Clean nozzle (fig.5)
Check that the voltage of the mains power supply line is
the same as that on the plate (fig.2)
insufficient power supply
voltage loss due to use of extension cable
Appliance not used for a long period of time
problems with Tss device
Check characteristics of extension cable
Contact your nearest Authorized service Centre
Contact your nearest Authorized service Centre
Motor “sounds” but fails to start
Check that the plug is firmly in the socket and that the
mains voltage supply is present (*)
no electrical power
Motor fails to start
Water leakage
problems with Tss device
Contact your nearest Authorized service Centre
Using the tool (L) unjam the motor from the hole at the
rear of the appliance (in models with this feature) (fig.5)
have the seals replaced at your nearest Authorized
service Centre
Appliance not used for a long period of time
seals worn
Appliance noisy
Water too hot
Reduce temperature (see technical data
oil leakage
seals worn
Contact your nearest Authorized service Centre
nozzle clogged
Clean nozzle (fig.5)
TSS versions only: motor starts
even with gun trigger is released
high pressure system or pump hydraulic circuit not
watertight
Contact your nearest Authorized service Centre
TSS versions only: no water deliv-
ery when gun trigger is depressed nozzle clogged
Clean nozzle (fig.5)
(with supply hose connected)
If the motor starts and does not restart during operation, wait 2-3 minutes before repeating the start-up procedure (overload cutout has been tripped).
if the problem recurs more than once, contact your nearest Authorized service Centre.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this
product is in conformity with the following
EN
standards or standardized documents
EN 60335-1 - EN 60335-2-79; EN 55014-1; EN 55014-2;
EN 61000-3-2;EN 61000-3-3; EN 61000-3-11; EN 60704-1
In accordance with the regulations:
98/37/CE
2006/95/CE, 2002/95/CE, 2002/96/CE, 2004/108/CE, 2000/14/CE
Date: 23/01/2008
MODENA (I)
stefano reverberi
Managing Director
|