Axis Communications Power Supply Q87 E User Manual

INSTALLATION GUIDE  
AXIS Q87-E Power Supply 230 V AC  
AXIS Q87-E Power Supply 120 V AC  
 
Safeguards  
Please read through this Installation Guide carefully before installing the product. Keep the  
Installation Guide for further reference.  
Store the Axis product in a dry and ventilated environment.  
Avoid exposing the Axis product to vibration, shocks or heavy pressure and do not install  
the product on unstable brackets, unstable or vibrating surfaces or walls, since this could  
cause damage to the product.  
Only use applicable tools when installing the Axis product; excessive force could cause  
damage to the product.  
Do not use chemicals, caustic agents, or aerosol cleaners. Use a damp cloth for cleaning.  
Only use accessories that comply with the technical specification of the product. These can  
be provided by Axis or a third party.  
Use only spare parts provided by or recommended by Axis.  
Do not attempt to repair the product by yourself, contact Axis or your Axis reseller for ser-  
vice matters.  
This Axis product shall be used in compliance with local laws and regulations.  
The Axis product should be installed by a trained professional. Please observe relevant  
national and local regulations for the installation.  
Transportation  
When transporting the Axis product, use the original packaging or equivalent to prevent  
damage to the product.  
 
 
AXIS Q87-E 230/120 V AC Installation Guide  
Page 5  
AXIS Q87-E Power Supply 230 V AC &  
AXIS Q87-E Power Supply 120 V AC  
Installation Guide  
This Installation Guide provides instructions for connecting AXIS Q87-E Power Supply 230/120 V AC  
with AXIS Q87-E Dual PTZ Network Camera Series.  
Installation Steps  
1. Check the package contents against the list below.  
2. Hardware overview. See page 6.  
Package Contents  
Item  
Models/variants/notes  
Power Supply  
Power supply (230/120 V AC) with built-in day/night sensor  
AXIS Q87-E 230/120 V AC Installation Guide (this document)  
Printed materials  
Tools needed (not included)  
Ratchet set  
Drill for drilling holes in mounting surface  
 
Page 6  
AXIS Q87-E 230/120 V AC Installation Guide  
Hardware Overview  
1
2
3
4
5
6
7
8
1
Power supply lid  
5
6
7
8
Cable gland (illuminator cable)  
Power supply box  
Day/night sensor  
2
3
4
Power supply lid screw (4x)  
Cable gland (mains power)  
Cable gland (unit power)  
Connector board  
 
 
AXIS Q87-E 230/120 V AC Installation Guide  
Page 7  
Install the Power Supply  
The mains supply shall be disconnected during installation.  
The supplied power supply shall be used. Using any other power supply will void the warranty  
and could leave the unit at a risk.  
The day/night sensor is attached to the power supply. If using the day/night sensor, place the  
power supply so that the sensor can track the changes in daylight.  
1. Install the power supply in the desired location. Make sure that the screws and plugs are appro-  
priate for the material (e.g. wood, metal, sheet rock, stone).  
2. Unscrew the lid screws and open the power supply.  
3. Route the network, power and, if applicable, the illuminator cables through the cable glands in  
the PTZ base.  
 
 
Page 8  
AXIS Q87-E 230/120 V AC Installation Guide  
4. Connect the pan/tilt power supply to the pan/tilt connector (6) in the power supply.  
5. If using the day/night sensor, connect the illuminator cable to the illuminator connector (J5) in  
the power supply.  
6. If using the day/night sensor, adjust the potentiometer to increase or decrease the sensitivity of  
the day/night sensor. see Connection Diagram, on page 9.  
Connect the mains supply cable to the mains supply connector in the power supply.  
1 2  
3
F1  
F2  
L1 L2  
K1  
P1  
J3  
J2  
J4 J5  
J1  
J6  
N
L
L
N
TR1  
TR2 TR3  
TR4 24~  
24~  
status  
Incoming mains  
-
+
4 5  
7
6 8 9  
1
2
3
4
5
6
7
8
9
Fuse F1  
Fuse F2  
Potentiometer  
Mains supply connector  
Mains supply cable  
Pan/tilt connector  
Pan/tilt power supply cable (24 V AC)  
Illuminator connector  
Illuminator cable  
7. Close the power supply and tighten the lid screws.  
8. Screw the cable gland caps on firmly.  
 
AXIS Q87-E 230/120 V AC Installation Guide  
Page 9  
Connection Diagram  
L
N
INCOMING  
MAINS VOLTAGE  
1
L
N
AXIS Q87-E  
POWER SUPPLY  
3
PE  
EXTERNAL PROTECTIVE  
GROUND WIRE  
2
1
2
3
Incoming mains voltage  
External protective ground wire  
AXIS Q87-E Power Supply  
Cable Specification  
Notes:  
• To maintain the products IP rating, the external diameter of the cables must be 5 - 10 mm.  
• The Pan/tilt power supply cable can not be longer than 3 m (9 ft).  
Cable  
Number of  
wires  
Cable area  
0.5 mm2 - 1.3 mm2 (AWG21 - AWG16)  
0.75 mm2 - 2.0 mm2 (AWG19 - AWG14)  
Mains supply  
cable  
3 (L, N, PE)  
Pan/tilt power  
supply cable (24 V  
AC)  
3 (L, N, PE)  
0.5 mm2 - 1.3 mm2 (AWG21 - AWG16)  
Illuminator cable 2 (signal, GND)  
 
 
Day/Night Sensor  
The day/night sensor is configured in the factory for optimal performance in a range of conditions.  
However, settings can be adjusted to suit specific conditions on site.  
To adjust the sensitivity of the day/night sensor, turn the potentiometer until it reaches the desired  
threshold. Turn the potentiometer clockwise to increase the threshold and advance the switch to  
night mode. Turn the potentiometer counterclockwise to decrease the threshold and delay the  
switch to night mode. The switch to night mode will activate the illuminators (sold separately).  
Technical Specifications  
Function/group  
Item  
Specifications  
Power supply  
Model  
AXIS Q87-E Power Supply 230 V AC  
AXIS Q87-E Power Supply 120 V AC  
General  
Operating con- -30 °C to 45 °C (-22 °F to 113 °F)  
ditions  
Humidity 50% – 100% RH (condensing)  
Overvoltage  
II  
Category (OVC)  
Fuses  
AXIS Q87-E Power Supply 230 V AC: F1 = 2 AT, F2 = 8 AT  
AXIS Q87-E Power Supply 120 V AC: F1 = 3,15 AT, F2 = 8 AT  
Approvals  
EN 55022 Class A, EN 55024,  
EN 61000-6-1, EN 61000-6-2  
FCC Part 15 Subpart B Class A demonstrated by compliance with  
EN 55022  
ICES-003 Class A demonstrated by compliance with EN 55022  
C-tick AS/NZS CISPR 22 demonstrated by compliance with EN 55022  
EN 61000-3-2, EN 61000-3-3  
EN 60950-1, EN 60950-22  
IEC/EN 60529 IP66  
Weight  
4 kg (8.8 lb.)  
Dimensions  
(HxWxD)  
278 mm x 242 mm x 90.5 mm (10.9” x 9.5” x 3.6”)  
Further Information  
guides.  
Warranty  
For information about Axis’ product warranty and thereto related information, see  
 
 
Installation Guide  
Ver.2.0  
Printed: April 2014  
Part No. 57182  
AXIS Q87-E 230/120 V AC  
© Axis Communications AB, 2013-2014  
 

Accusplit Headphones AE2700 User Manual
AEG Cooktop 6010 K User Manual
Agilent Technologies Power Supply 66312A User Manual
Aiwa CD Player XR X77 User Manual
Allied Air Enterprises GPS Receiver KLN 90B User Manual
Allied Air Enterprises Heat Pump 4HP16LT User Manual
AMD Computer Hardware 7ZMMC User Manual
Ativa Paper Shredder DMC120D User Manual
Atlona TV Cables AT PRO2HD1616M RX User Manual
Axor Indoor Furnishings 16530XX1 User Manual