ATON Stereo Receiver AIR6 User Manual

3. Connect the Cat-5 wires to the correct location on the AIB4 connection  
terminals (+12VDC, IR, STATUS, and GND).  
Stand-Alone System Connections:  
A: Basic System  
Figure 2 shows a basic IR distribution system using the ATON AIB4 Amplified IR  
Connection Block, AIR6 In-Wall IR Receiver, and AIE2 Talk-Back IR Emitters to con-  
trol source equipment.  
Advanced IR Filtering Technology  
AIR6  
The AIR6 features Advanced IR Filtering Technology that reduces IRI, CFL, EMI,  
and ESI noise sources in addition to blocking plasma TV emissions. This means  
that the AIR6 can be used in areas that receive substantial ambient noise such  
as near plasma TVs or compact flourescent lights.  
4. Install and plug the AIE1 Emitters into the AIB4.  
5. Set the DIP switches to LP ON and NET ON.  
6. Plug the local AIR5 IR Receiver into the IR RECEIVER jack.  
7. Plug in the PS2 12VDC Power Supply.  
8. IR signals sent to the AIR6s will pass through the AIB4 and control the  
equipment.  
In-Wall  
IR Receiver  
AIR6  
NOTE: The AIR6 will take a few seconds to adjust to a given noise source. During  
this time, the blue Activity LED will glow brightly and then fade out. If the inter-  
ference disappears momentarily,then returns, the fade down process will repeat.  
Certain noise sources, however, (such as plasma screens) may result in low-level  
flickering even after the fade down. This is normal. Such signals have been fil-  
tered, allowing most equipment to be controlled.  
In-Wall  
IR Receiver  
NOTE: Refer to the ATON AIB4 Instructions for power supply considerations and  
other important information.  
Introduction  
The ATON AIR6 is a small, attractively styled ‘plasma-friendly’ IR receiver  
designed to fit in-wall electrical boxes (J-Boxes). This receiver uses advanced IR  
filtering technology which allows it to work even in areas that receive normally  
harmful interference (near plasma TV’s, compact flourescent lights, etc.).  
A/V Receiver  
Connection  
Terminals  
ROOM 3  
ROOM 1  
ROOM 2  
AIR1  
AIR1  
AIR6  
Surface-Mount  
IR Receiver  
Limited Warranty  
Surface-Mount  
IR Receiver  
In-Wall IR Receiver  
AIE2 Talk-Back Emitter  
Satellite  
ATON* warrants to the purchaser/end user (“you”) that the AIR6 is to be free from defects in materials and  
workmanship for a period of five (5) years from date of purchase (the “Warranty Period”). This warranty is  
transferable to subsequent owners of the product as long as the original proof of purchase is retained. If  
you discover a defect in material or workmanship within the Warranty Period, you can obtain warranty ser-  
vice by contacting ATON during the Warranty Period at (859)-422-7137 or [email protected]. If ATON  
determines that the product is in fact defective, ATON shall, at its option, repair or replace the product free  
of charge to you.  
Features (Refer to Figure 1)  
Striped  
Striped  
Side  
Side  
• Stripped Leads Plus a 4-Conductor Terminal Strip  
• ‘Plasma-Friendly’ Technology Helps Block Plasma TV Interference  
• IR Lens Rejects Visible Light Interference  
• Internal Crosshatch Shield Inhibits EMI/ESI Interference  
• STATUS Indicator: Green LED for System On/Off indication  
• ACTIVITY Indicator: Blue LED indicates IR signal activity  
GND  
+12V  
IR OUT  
IR OUT  
GND  
+12V  
STATUS  
Rear View  
STATUS  
Connection Block  
AIE2 Talk-Back Emitter  
DVD  
Rear View  
Add Resistor at each IR receiver  
to reduce STATUS brightness,  
if desired. See text.  
This warranty shall not apply to equipment (a) not manufactured by ATON, (b) to equipment which was  
improperly installed, (c) which was repaired or altered by persons other than ATON or its authorized repre-  
sentatives or subject to unauthorized tampering, alteration or modification, (d) damaged due to misuse,  
negligence, accident, acts of God (including, but not limited to, excess moisture, insects, lightning, flood,  
electrical surge, tornado, earthquake, or other catastrophic events beyond ATON’s control), or (e) subject to  
improper operation, maintenance or storage or unreasonable use. The foregoing warranties do not cover  
reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in  
connection with repair or replacement. The foregoing remedies shall be your exclusive remedies for any  
breach of warranty.  
Wh/Blue IR  
Blue STATUS  
Brown GROUND  
Wh/Green +12 VDC  
To Switched  
AC Outlet  
PS2  
Power  
AIE2 Talk-Back Emitter  
Supply  
Connection Terminals  
Front  
Rear  
1-1/2" (38mm)  
AIB4  
A/V Receiver  
To 120V AC  
Amplified IR  
(unswitched)  
Figure 2  
Connection Block  
Connection  
Terminals  
Decora® Style  
Insert Plate  
AIR5  
Tabletop  
PS2  
AIE1 Emitter  
Satellite  
STATUS  
Supply  
1. Pull Cat-5 from the AIR6’s mounting location to the connection terminals of an  
AIB4 Amplified IR Distribution Block.  
2. Connect the Cat-5 wires and IR emitters into the AIB4, as shown.  
3. Using the provided screws, mount the AIR6 into a J Box-type electrical box.  
4. Set the DIP switches on the AIB4 to LP ON and NET ON or OFF.  
5. Plug in the power supply.  
IR Receiver  
IR Pickup  
Diode  
Further, the foregoing warranty does not extend to equipment sold, but not manufactured by, ATON (“Third  
Party Products”). With respect to any Third Party Products, the warranty for such product shall be as pro-  
vided by the manufacturer of such product, who will also be responsible for warranty service, and ATON will  
pass through to you any transferable warranty actually extended to ATON by the manufacturer.  
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED  
WARRANTIES. ATON EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED  
TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-  
INFRINGEMENT. Notwithstanding the above, where applicable, if you qualify as a “consumer” under the  
Magnuson-Moss Warranty Act, then you may be entitled to any implied warranties allowed by law for the  
Warranty Period. Some states do not allow limitations on how long an implied Limited Warranty lasts, so the  
above limitation may not apply to you.  
IR Lens  
4"  
(102mm)  
AIE2 Talk-Back Emitter  
Status LED  
(Green)  
DVD  
Activity LED  
(Blue)  
PS2  
AIB4  
or PS3  
Amplified IR  
Connection Block  
AIE2 Talk-Back Emitter  
Power  
Supply  
6. IR signals sent to the AIR6 will pass through the AIB4 and control the  
equipment.  
To 120V AC  
(unswitched)  
Figure 1  
B: Multi-Room System  
Figure 3 shows an example of multiple AIR6 IR Receivers in a stand-alone multi-  
room system. These control the various components in the equipment area.  
ATTENTION: TO OUR VALUED CONSUMERS  
Figure 3  
Specifications:  
Valid proof of purchase is required for all warranty services. Warranty service requests made without proof  
of date of purchase will be denied. Please keep the original sales receipt for your records and send a copy to  
request warranty service.  
• Requires 12VDC power supply, termination block, and IR emitters for IR  
operation.  
1. Pull Cat-5 from each room (home runs) to the AIB4 terminator near the  
controlled components.  
• Mounting: Fits in standard single-gang (J-Box) electrical boxes  
• Power: +12VDC @ 6mA  
This warranty gives you specific legal rights, and you may also have other rights which vary from state to  
state.  
* ATON is a division of ELAN Home Systems, LLC.  
STATUS Brightness  
Figure 3 also shows how an external resistor can be added to reduce the bright-  
ness of the Status LEDs on ATON IR receivers. In this example, a PS2 12VDC  
Power Supply is used as the voltage source to indicate ON/OFF status of an A/V  
Receiver. Choose a resistor value that achieves the brightness you desire (about  
2.2k to 12k, 1/8W). Connect it in series with the STATUS lead on each IR receiver,  
as shown.  
• Carrier Frequency Acceptance Range: 28kHz to 90kHz  
• Control Range: Up to 35 feet, depending on remote strength and ambient noise  
conditions  
NOTE: MAX DISTANCE of ALL Wire Runs is 1200 ft using Cat-5 cable. When using  
long lengths, the dipswitch on the AIB4 must be set to the NET ON position and a  
500 Ohm resistor must be used.  
• Control Angle: +/- 50 degrees off-axis  
• Room-to-Room Wire Recommendations: Cat-5  
• Maximum recommended cable length: 1200 feet using Cat-5  
• Dimensions: 4” (102mm) H x 1¼2” (38mm) W x 1” (25mm) D  
2. Connect IR receivers in each room to the Cat-5 runs as shown, using the termi-  
nal strips supplied.  
©2007 • All rights reserved.  
P/N 227948 REV:C  
 
1
2
3
4

Accusplit Fitness Electronics 998 314 User Manual
Acer Laptop 290E User Manual
Acer Laptop 3030 Series User Manual
Acer Projector K11 User Manual
Air King Greenhouse Kit Ak912 User Manual
Amana Oven RS2320006 User Manual
Axor Outdoor Shower 27192XX1 User Manual
Axor Plumbing Product 06573000 User Manual
Bakers Pride Oven Oven C 48R User Manual
Behringer Mixer RX1202FX User Manual