RF2IR
RF Base Station
Quick Start
Installation Instructions
ATTENTION: Requires the XTR39 to operate.
- 1 -
RF2IR Diagram (Front)
IR LED, RF LED: Flashes when emitting IR and RS232 commands
Quick Start Instructions
Step 1. Plug the (4) 283M emitters (included) into the port labeled IR output 1 thru 4 on the back of
the RF2IR. Next, place the associated 283M emitter head directly over the IR eye on the proper
source component to be controlled.
Step 2. Plug the RS232 Adapter Cable (if required) into the RF2IR port labeled RS232. Next, connect
the DB9 plug to the source component to be controlled. In some instances, a null modem converter
may be required. Below is a pin-out of the RS232 Adapter Cable.
Step 3. Plug the power supply into the RF2IR port labeled 12VDC. The IR and RF LEDs will
illuminate for 10 seconds. This is part of the start-up sequence. After the LEDs turn ‘off’, the RF2IR is
ready to be used.
Step 4. Follow the XTR39 Instructions, RF2IR Addendum and follow the steps to setup the XTR39.
- 3 -
RF2IR Configuration (Channel Address)
The Channel Address on the RF2IR cannot be programmed using Universal Dragon. Located on the
bottom of the RF2IR device is a rotary switch. Turn this switch to select the desired Channel Address.
The switch is labeled in HEX notation. “A” stands for Channel Address “10”. “B” stands for Channel
Address “11”. The Channel Address increments with the alphabet until it ends at “F”, which is “15”.
Locating the RF2IR
Thanks to Xantech’s superior antenna design, the RF2IR can be placed in several locations.
Key Location Points:
• The RF2IR should be placed on a flat, stable surface.
• For optimal performance, the RF2IR should be placed at a height greater than 3 feet above the
floor. The ideal height should be level to the XTR39 transmitter.
• Avoid placing the RF2IR near corners of a room.
• Avoid placing the RF2IR next to microwave ovens.
Care and Maintenance
Clean the outside of the plastic housing using a soft cloth. Use warm water and mild soap solution.
Do not use abrasive cleaners.
Information
FCC NOTICE
* Section 15.19 Labeling requirements
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference and
0197
(2) This device must accept any interference received,
including interference that may cause
undesired operation.
RF2IR RF Base Station Quick Start Installation Instructions
© 2006 Xantech Corporation
* Section 15.21 Information to user
The changes or modifications not expressly approved by
the party responsible for compliance
could void the user’s authority to operate the
equipment.
This document is copyright protected. No part of this manual may be
copied or reproduced in any form without prior written consent from
Xantech Corporation.
* IMPORTANT NOTE: To comply with the FCC RF
exposure compliance requirements, no change to the
antenna or the device is permitted. Any change to the
antenna or the device could result in the device
exceeding the RF exposure requirements and void
user’s authority to operate the device.
Xantech Corporation shall not be liable for operational, technical, or
editorial errors/omissions made in this document.
Document Number 08905083A
- 4 -
Xantech Limited Warranty
(Effective for products sold after July 1, 2006)
Xantech Corporation (“Xantech”) warrants to the holder of a valid proof of purchase as the first end-user purchaser
(“You”), its products to be free from defects in materials and workmanship for the periods specified below from the date of
purchase. This limited warranty extends only to You for product purchased and used in the United States of America. For
product purchased outside of the United States of America, the terms of this warranty apply EXCEPT that You must
contact the Xantech authorized distributor in your region for warranty services. Product is not intended for end user
installation. If within the applicable warranty period above You discover such item was not as warranted above and You
promptly notify Xantech in writing, Xantech shall repair or replace the items at its option. Xantech may elect which remedy
or combination of remedies to provide in its sole discretion. Xantech may use functionally equivalent
reconditioned/refurbished/pre-owned or new products or parts under this limited warranty. This warranty shall not apply
(a) to product which shall have been installed by other than an authorized Xantech installer, (b) to installed product which
is not installed to Xantech’s specifications, (c) to product which shall have been repaired or altered by others than
Xantech, (d) to charges for installation or set up or adjustment of customer controls, (e) to product that has suffered
normal cosmetic deterioration (f) to product which shall have been subjected to negligence, misuse, abuse, accident, or
damage by circumstances beyond Xantech’s control, including, but not limited to, lightning, flood, electrical surge,
tornado, earthquake, or any other catastrophic events beyond Xantech’s control, or (g) to product which shall have been
subjected to improper operation, connected equipment failure or malfunction, inadequate packing or shipping damage,
maintenance or storage, or to other than normal use of service. The foregoing warranties do not cover reimbursement for
labor, transportation, shipping, removal, installation, or other expenses which may be incurred in connection with repair or
replacement. All claims for product shipping damage must be processes within 3 days of receipt by You.
A Xantech Return Authorization (RA) must be obtained from Xantech by You, your installer or your distributor for Product
covered under this warranty. Covered product must be sent to Xantech together with proof of purchase, RA number,
prepaid and insured to Xantech. Freight collect shipments will be refused. Risk of loss or damage in transit is borne by the
sender. Xantech's warranty does not cover Products which have been received improperly packaged, altered, or
physically damaged. Products will be inspected upon receipt.
Except as may be expressly provided and authorized in writing by Xantech, Xantech shall not be subject to any
other obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services
rendered by Xantech.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED
WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE.
ATTENTION: TO OUR VALUED CONSUMERS
To insure that consumers obtain quality pre-sale and after-sale support and service, Xantech products are sold
exclusively through authorized dealers and authorized distributors. Xantech products are not sold online. The
warranties on Xantech products are NOT VALID if the products have been purchased from an unauthorized
distributor or an online E-tailer. In order to determine if your Xantech re-seller is authorized, please call Xantech
(800) 843 - 5465.
XANTECH PRODUCT (go to Xantech.com/warranty for model numbers)
IR Receivers and IR Emitters
A/V distribution and Control
Remote Control Switchers
Modules and Connecting Blocks
Accessories
WARRANTY DURATION
Limited Lifetime
Limited Lifetime
Limited Lifetime
Limited Lifetime
Limited Lifetime
Limited Lifetime
5 year Limited
Speakers
Volume Controls and Speaker Selectors
MRC, BX, ZPR and Commercial Products
Amplifiers
2 year Limited
2 year Limited
Control Interfaces
2 year Limited
Hand Held Remote Controls
SPLCD Product
1 year Limited
1 year Limited
Source Components
1 year Limited
|