ZANUSSI
FREEZER
ZEUT 6245
INSTRUCTION BOOK
GB
200369475
A/ZE/17. (04.)
IMPORTANT SAFETY INSTRUCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings or these warnings contact the Customer Care Department.
Prior to installation
Do not place carbonated or fizzy drinks in the
freezer.
Check the appliance for transport damage. Under
no circumstances should a damaged appliance be
installed. In the event of damage please contact
your retailer.
Ice lollies can cause 'frost/freezer burns' if
consumed straight from the freezer.
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
Bottles and cans must not be placed int the
freezer they can burst when the contents freeze.
Manufacturers' recommended storage times should
be adhered to. Refer to relevant instructions.
Installation
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
Ensure that the appliance does not stand on the
electrical supply cable. If the supply cable is
damaged, it must be replaced by a cable available
from your local Service Force Centre.
Make sure that the power plug is not squashed
or damage the back of the fridge/freezer.
- A damaged power plug may overheat and cause a
fire.
Maintenance and Cleaning
Before cleaning, always switch off the appliance
and disconnect from the electrical supply.
When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Servicing
This product should be serviced by an
authorised engineer and only genuine spare
parts should be used.
Do not place heavy articles or the
fridge/freezer itself on the power cord.
- There is a risk of a short circuit and fire.
Do not remove the power cord by pulling on its
lead, particularly when the fridge/freezer is
being pulled out of its niche.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Contact your local
Service Force Centre.
- Damage to the cord may cause a short-circuit, fire
and/or electric shock.
- If the power cord is damaged, it must be replaced
by a certified service agent or qualified service
personnel.
At the end of the Appliance Life
When disposing of your appliance use an
authorised disposal site.
If the power plug socket is loose, do not insert
the power plug.
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
- There is a risk of electric shock or fire.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall, but leaving the required
distance for ventilation, as stated in the installation
instructions.
Safety precautions for isobutane
Warning
The refrigerant isobutane (R 600a) is contained
within the refrigerant circuit of the appliance, a
natural gas with a high level of environmental
compatibility, which is nevertheless flammable.
Keep ventilation openings, in the appliance
enclosure or in the built-in structure, clear of
obstruction.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Do not use mechanical devices or other means
to accelerate the defrosting process, other than
those recommended by the manufacturer.
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance.
Child Safety
Do not allow children to tamper with the controls or
play with the product.
There is a risk of suffocation! Keep packaging
material away from children!
The Appliance and the Environment
During Use
This appliance does not contain gases which could
damage the ozone layer.
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs. It is
not intended for commercial or industrial use.
Containers with flammable gases or liquids can
leak at low temperatures. Do not store any
containers with flammable materials, such as spray
cans, fire extinguisher refill cartridges etc. in the
freezer.
Avoid damaging the cooling unit.
The packaging used on this appliance marked with
the
symbol is recyclable.
Keep this instruction book for future reference
and ensure it is passed on to any new owner.
Frozen food should not be refrozen once it has
thawed out.
3
CONTENTS
Instructions for the User
Guide to use the instruction book
Important Safety Information
Instructions for the Installer
2
3
Technical Specifications
13
Installing the Appliance
Transportation, Unpacking
Location
Ventilation Requirements
Levelling
13
13
13
14
14
Instructions for the User
General Information
Description of the Appliance
5
5
5
Door Reversal
14
15
Indicator Lights
Fast Freeze Facility
Basket Storage
Freezer Tray
6
6
6
6
Electrical Connection
Using the Appliance
Before Use
To Start the Appliance
Thermostat Control
Freezing Fresh Food
Frozen Food Storage
Thawing
7
7
7
7
7
8
8
8
Making Ice Cubes
Hints and Tips
Food Storage
Energy Saving Advice
In the Event of a Power Failure
8
8
9
9
Maintenance and Cleaning
Internal cleaning
External cleaning
When the appliance is not in use
Defrosting
9
9
9
9
9
Something Not Working
Service and Spare Parts
Customer Care Department
Guarantee Conditions
10
11
11
12
4
INSTRUCTIONS FOR THE USER
To ensure correct operation, the appliance should
be located where the ambient temperature is
between 16-32 °C.
General information
This appliance is designed for the freezing and
storage of frozen food in a domestic home.
Description of the Appliance
9
5
10
1
2
8
11
3
4
12
13
6
7
1. Freezing tray (with 1 ice cube tray)
2. Freezing compartment
3. Storing compartments (wire baskets)
4. Rating Plate
6. Defrost water outlet
7. Adjustable feet
8. Door gasket
9. Thermostat
5. Control Panel
10. Air grid
a) Green Indicator Light
11. Condenser
12. Air circulation
13. Compressor
b) Red Indicator Light
c) Yellow Indicator Light
d) Fast Freeze Switch (continuous operation)
e) Thermostat control knob
5
Indicator Lights
The indicator lights are situated in the control panel.
A.)Green Indicator Light
When the appliance is switched on at the mains the
green indicator light will illuminate and remain lit
until the appliance is switched off at the mains.
B.)Red Indicator Light
A few hours after starting up the red indicator light
will go out to show that the correct temperature has
been reached for the setting chosen and will stay
out to indicate that everything is in order.
It will come on if the freezer temperature rises
unduly for instance, after opening the freezer door
or placing food inside the cabinet, but the light
should go out again when the temperature returns
to the correct storage level.
C.)Yellow Indicator Light - (Fast Freeze)
When fast freeze is switched on the Yellow
Indicator Light will illuminate and remain lit until fast
freeze is switched off.
D.)Fast Freeze Facility
To operate the Fast Freeze Facility slide the switch
to the right hand position.
E.)Thermostat Control
This is for setting and changing the temperature
inside the appliance.
Basket Storage
Frozen food should be stored in the two lower baskets
and the top compartment used for storage or fast
freezing of fresh food.
Freezer Tray
The Freezer Tray is particularly suitable for open
freezing, for example strawberries, raspberries etc.
6
Using the Appliance
Before Use
Remove all packaging and securing tapes. Wash
inside the appliance with lukewarm water and
bicarbonate of soda (5 ml to 0,5 litre of water). Do not
use soap or detergent as the smell may linger. Dry
thoroughly.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or products containing alcohol.
To Start the Appliance
)
1. Allow the appliance to stand for 2 hrs after
installation.
2. Plug in the appliance and switch on at the mains
supply.
3. Slide the 'fast freeze' switch to the right (yellow
indicator light will illuminate) and leave to run for 4
hours to allow the correct temperature to be
reached before placing food inside.
4. The red indicator light will also illuminate until the
correct temperature is reached.
5. When the appliance has reached the set
temperature and the red indicator light has gone
out slide the 'fast freeze' switch back to the left.
Thermostat Control
The temperature within the freezer is controlled by the
thermostat control knob situated on the control panel.
0 = Off
Turning the thermostat control knob clockwise makes
the temperature progressively colder.
Freezing Fresh Food
It is important that fresh food placed in the freezer is
frozen quickly and that the food already in the freezer
is heated as little as possible.
If more than 3-4 kg of food is to be frozen:
)
1. Slide the fast freeze switch (d) to the right 6-24
hours before placing the fresh food in the freezer,
the yellow light will illuminate. The compressor will
now run continuously, to ensure that the fresh food
is frozen as quickly as possible.
2. Place the food in the freezing compartment and
leave the 'fast freeze' switch on for a further 24
hours.
7
3. After 24 hours, slide the 'fast freeze' switch back to
the left (the yellow light will go out) and transfer the
food to the storing compartments. The freezer will
return to normal storage temperature.
To Make Ice Cubes
1. Fill the ice cube tray 3/4 full with cold water,
place in the freezing compartment and leave to
freeze.
)
If the 'fast freeze' switch is accidentally left on,
the freezer will not be damaged, but energy
will be wasted.
2. To remove the cubes twist the tray or hold it
under running water for a few seconds.
Never try to free an ice tray that is frozen
to the freezer compartment by using
pointed or sharp edged objects.
Frozen Food Storage
When first starting the freezer or if the freezer has
been out of use for some time, we advise you to run
your appliance for at least 2 hours with the 'fast freeze'
switch on before storing frozen food.
Hints & Tips
Food Storage
Do not exceed the storage period indicated by the
manufacturer.
To obtain the best performance from your freezer:
Do not store warm food or evaporating liquid.
Do not open the door frequently or leave it open
longer than is necessary.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container
is advisable. When you arrive home, place the
frozen food in the freezer immediately.
Important
Do not put carbonated liquids in the freezer.
Ice lollies, if consumed immediately after removal
from the freezer can cause a low temperature skin
burn.
Do not push food together too much, try to allow
air to circulate around each item.
Do not store food uncovered.
Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions or
frost/freezer burns.
Ensure that food placed in the freezer is dated
and labelled and used in date order to ensure
that food is consumed at its best.
In the event of a power cut the food in the freezer
will not be affected if the power cut is short and the
freezer is full. Do not open the lid. Should the food
begin to thaw it must be consumed quickly and
must not be re-frozen. (See Hints and Tips)
Lean food keeps better and longer than fatty
food, salt reduces the storage time.
Wrap the food in polythene or aluminium
freezing bags or foil so that they adhere to the
food and provide an airtight seal.
Packaging which is swollen or has traces of
refrozen water droplets on the pack could
indicate that the product has not been kept at a
suitable temperature and that it may have lost its
original quality. Partially thawed food must not be
refrozen, it must be consumed within 24 hours.
Never exceed the storage times indicated by the
manufacturer.
Thawing
Deep frozen or frozen food, prior to being used, can
be thawed in a fridge or at room temperature,
depending on the time available. Small food items may
even be cooked from frozen, in this case cooking will
take longer.
Any frozen food which is allowed to thaw accidentally
should either be eaten as soon as possible, or thrown
away. Alternatively, if the food is uncooked and has not
been completely defrosted it can be cooked and then
refrozen.
Defrosted cooked food must never be
refrozen.
8
Energy Saving Advice
In the Event of a Power Failure
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
If there is a power failure during the storage of
frozen foods, keep the door closed. If the
temperature within your freezer should rise, do not
refreeze the food without checking its condition.
The following guidelines should assist you:
Locate the appliance in a cool well ventilated room
and make sure that the air openings of the
appliance are not obstructed.
Ice Cream: Once thawed should be discarded.
Avoid unnecessary frosting in the cabinet by
packing all foodstuffs into airtight packages before
placing them in the freezer.
Fruits & Vegetables: If soft should be cooked and
used up.
Food which is to be frozen (when cool) should be
placed in the fridge before being transferred to the
freezer.
Breads & Cakes: Can be refrozen without danger.
Shellfish: Should be refrigerated and used up
quickly.
Try to avoid keeping the door open for long periods
or opening the door too frequently as warm air will
enter the cabinet and cause the compressor to
switch on unnecessarily often.
Cooked Dishes: i.e. casseroles should be
refrigerated and used up.
Large Pieces of Meat: Can be refrozen providing
there are still ice crystals remaining within them.
Ensure there are no obstructions preventing the
door from closing properly.
Small Joints: Should be cooked and can then be
refrozen as cooked dishes.
Chicken: Should also be cooked and refrozen as a
fresh dish.
Maintenance & Cleaning
When the Appliance is not in
Use
Before any maintenance or cleaning is
carried out you must DISCONNECT the
appliance from the electricity supply.
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the door
open to prevent unpleasant smells.
Internal Cleaning
Clean the inside and accessories with warm water and
bicarbonate of soda (5 ml to 0.5 litre of water).
Rinse and dry thoroughly.
NEVER use detergents, abrasive powders,
highly perfumed cleaning products or wax
polishes to clean the interior as these will
damage the surface and leave a strong
odour.
Defrosting
The freezer compartment will become progressively
covered with frost. This should be removed with the
special plastic scraper provided whenever the
thickness of frost exceeds 6mm (¼”).
External Cleaning
Wash the outer cabinet with warm soapy water.
During this operation it is not necessary to switch
off the power supply or to remove the foodstuffs.
However, when the ice becomes very thick on the
inner liner, complete defrosting should be carried
out and it is advisable to peform this operation
when the appliance is empty.
Once or twice a year dust the condenser (black grille)
and the compressor at the back of the appliance with
a brush or vacuum cleaner, as an accumulation of dust
will affect the performance of the appliance and cause
excessive electricity consumption.
9
5. During defrosting, push the defrost water
towards the edge of the cooling plates using a
dry cloth or a sponge. It will be collected at the
bottom of the appliance, from where it can be
diverted into the tray and then disposed of.
To carry out complete defrosting:
)
1. Disconnect the appliance from the electrical
supply. If the plug is inaccessible turn the
thermostat control knob to „0“.
6. To accelerate the defrosting process place a
bowl of hot (not boiling) water inside the freezer
and close the door.
2. Remove any stored food, wrap in several layers of
newspaper and store in a cool place.
3. Leave the door open.
7. When defrosting is completed, dry the interior
thoroughly, replace the drain spout and close
the door.
4. Carefully draw the plastic drain spout out of the
lower part of the appliance according to the
direction of the arrow and place a tray of a suitable
size in the position shown.
8. Turn the thermostat control knob back to a
medium setting and leave to run for at least 4
hours with the 'fast freeze' switch on.
9. Replace the previously removed food.
Important
A temperature rise of the frozen food packs
during defrosting may shorten their safe storage
life.
Never use sharp metal tools to scrape off frost
from the evaporator as this could damage the
appliance beyond repair.
Something Not Working
If the appliance is not working correctly, please carry out the following checks before contacting your local
Zanussi Service Force Centre.
Problem
Possible Cause
No power at the socket.
Solution
No power to the
appliance
Check there is power at the socket.
There is a power cut.
Check there is not a power cut by checking the
household lights.
The fuse has blown.
Check the fuse has not blown.
Check the thermostat setting.
Thermostat control is set at „0“.
The appliance is located in an unsuitable position.
The temperature in the
appliance is too high
Check the ambient temperature is within the
appliances operating limits of 16 °C to 32 °C.
The thermostat control is set too low.
The thermostat control is set too high.
Check that the thermostat control knob is turned to
the correct setting relative to ambient conditions.
The temperature in the
appliance is too low
Set the thermostat control knob to a lower
position.
Excessive frost and ice
has built up
The door has been left open.
Something is obstructing the door.
The door gasket is dirty.
Check the door has not been left open.
Check nothing is preventing the door from closing.
Check the door gasket is intact and clean.
The appliance is noisy.
The appliance is not level.
Check if the appliance stands stable (all four feet
should be on the floor).
If after the above checks your appliance still does not
operate correctly, contact your local Zanussi Service
Force Centre.
In-guarantee customers should ensure that the
above checks have been made, as the
engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
Please note that it will be necessary to provide proof
of purchase for any in-guarantee service calls.
10
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:-
08705 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working."
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
Customer Care Department
For general enquiries concerning your Zanussi - Electrolux appliance or for further information on
Zanussi - Electrolux products, please contact our Customer Care Department by letter or telephone at the
Customer Care Department
Zanussi - Electrolux
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 (*)
*calls to this number may be recorded for training purposes.
11
Guarantee Conditions
We Zanussi - Electrolux undertake that if within 12
EUROPEAN GUARANTEE
months of the date of the purchase this
ZANUSSI - ELECTROLUX appliance or any part
thereof is proved to be defective by reason only of
faulty workmanship or materials, the company will, at
our option repair or replace the same FREE OF
CHARGE for labour, materials or carriage on condition
that:
If you should move to another country within
Europe then your guarantee moves with you to your
new home subject to the following qualifications:
The guarantee starts from the date you first
purchased your product.
The guarantee is for the same period and to the
same extent for labour and parts as exists in the
new country of use for this brand or range of
products.
The appliance has been correctly installed and
used only on the electrical supply stated on the
rating plate.
This guarantee relates to you and cannot be
transferred to another user.
The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer's instructions.
Your new home is within the European
Community (EC) or European Free Trade Area.
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
The product is installed and used in accordance
with our instructions and is only used
domestically, i.e. a normal household.
All service work under this guarantee must be
undertaken by a Service Force Centre.
The product is installed taking into account
regulations in your new country.
Any appliance or defective part replaced shall
become the Company's property.
Before you move please contact your nearest
Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your
move and able to look after you and your
appliances.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
EXCLUSIONS
France
Germany Nurenberg
Italy
Sweden
UK
Senlis
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
This Guarantee does not cover:
Damage or calls resulting from transportation,
improper use or neglect, the replacemet of any light
bulbs or removable parts of glass or plastic.
Pordenone +39 (0) 0434 39 4700
Stockholm
Slough
+46 (0) 8 672 53 90
+44 (0) 1753 219897
Costs incurred for calls to put right an appliance
improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial
environment, plus those which are the subject of
rental agreements.
Products of Zanussi - Electrolux manufacture
which are not marketed by Zanussi - Electrolux.
The guarantee is in addition to your statutory and legal
rights.
12
Instructions for the Installer
Technical Specifications
Model
ZEUT 6245
117
Gross capacity (l)
Net capacity (l)
100
550
850
600
0.56
204
A
Width (mm)
Height (mm)
Depth (mm)
Energy consumption (kWh/day)
(kWh/year)
Energy class, according to EU Standards
Freezing capacity (kg/24h)
Rising time (h)
12
17
Rated power (W)
Weight (kg)
90
39
Location
Installing the appliance
The appliance should be positioned in a well
ventilated, dry room.
Transportation, unpacking
The appliance and the interior fitting are protected for
transport.
Energy use is affected by the ambient temperature.
The appliance should therefore:
Remove all packaging and any adhesive tape.
Any remnants of adhesive can be removed using
white spirit.
not be installed next to radiators, cookers or
other sources of heat
After transportation the appliance must not be
switched on for 2 hours. This is to allow the
refrigerant to settle.
only be installed at a location where the ambient
temperature corresponds to the climate
classification, for which the appliance is
designed.
The climate classification can be found on the
rating plate.
The following table shows which ambient
temperature is correct for each climate
classification:
Cleaning
Clean the accessories and the inside of the appliance
with warm water and bicarbonate of soda (5 ml to 0.5
litres of water). Rinse and dry thoroughly.
Climate Classification Ambient Temperature
Do not use detergents, abrasive powders, highly
perfumed cleaning products, wax polishes or
cleaning products containing bleach or alcohol.
SN
N
+10 to +32 °C
+16 to +32 °C
+18 to +38 °C
ST
13
Ventilation Requirements
The appliance must have adequate ventilation to
ensure correct operation.
Diagram shows the ventilation requirements when
installed:
A* Under a worktop, or cupboard.
* The clearance space of 10 cm above the appliance
may be reduced to 5 cm providing a clearance
space 2.5 cm is left on either side of the appliance.
B When freestanding
Levelling
The appliance must be level. Level the appliance by
adjusting the two adjustable feet (1) at the front of the
appliance.
If required the washer (2) can be removed.
2
1
Door Reversal
If required the opening direction of the door can be
changed as follows:
Disconnect the appliance from the electricity
supply.
Tilt the appliance backwards, resting the top edge
of the appliance on a stool or something similar.
Unscrew the adjustable feet situated on both sides
at the front (2 pieces). Remove the lower door
hinge plate by unscrewing the 3 retaining screws.
Remove the hinge pin from the bottom of the door.
Slot the hinge pin into the hole in the hinge plate.
Take the door off.
14
Refit the upper hinge pin into the opposite location.
Fit the door in place on the hinge pin.
Slot the hinge pin into the hole in the hinge plate
and relocate the hinge assembly to the opposite
location and refit using the retaining screws.
Refit the bottom hinge plate assembly on the
opposite side, taking care that the edge of the door
is parallel with the side of the cabinet.
To reverse the handle proceed as follows:
Remove screw covers (if fitted) and handle retaining
screws. Remove blanking plugs on the opposite
side using a punch.
Relocate the handle to the opposite side and refit
retaining screws (covers if fitted), and push the
plastic plugs supplied with the instruction book into
the holes where the handle was previously fitted.
Electrical Connection
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability should
these safety measures not be observed.
Electrical Requirements
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug
supplied, a 13 amp ASTA approved (BS 1362) fuse
must be used. Should the plug need to be replaced
15
for any reason. The wires in the mains lead are
coloured in accordance with the following code:
Green and Yellow:
Blue:
Earth
Neutral
Live
Brown:
The wire coloured green and yellow must be
connected to the terminal marked with the letter „E“ or
by the earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal „N“ or coloured black.
The wire coloured brown must be connected to the
terminal marked „L“ or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
This appliance complies with the following
E.E.C. Directives:
73/23 EEC of 19.02.73 (Low Voltage Directive)
and subsequent modifications,
89/336 EEC of 03.05.89 (Electromagnetic
Compatibility
modifications.
Directive)
and
subsequent
© Electrolux plc 2004
ELECTROLUX HOME PRODUCTS OPERATIONS EUROPE
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux
Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of
approx. USD 14 billion in more than 150 countries around the world.
|