Yamaha Music Mixer DSP1D EX User Manual

-EX  
Owner’s Manual  
V480360 R0 1 IP 16  
E
200 AP Printed in Japan  
 
Precautions  
• Do not allow water to enter this unit or allow the unit  
to become wet. Fire or electrical shock may result.  
• The digital circuits of this unit may induce a slight  
noise into nearby radios and TVs. If noise occurs,  
relocate the affected equipment.  
• Connect this unit’s power cord only to an AC outlet of  
the type stated in this Owner’s Manual or as marked  
on the unit. Failure to do so is a fire and electrical  
shock hazard.  
• If the message “WARNING LOW BATTERY!” appears  
when you turn on this unit, contact your dealer as  
soon as possible about replacing the internal data  
backup battery. The unit will still operate correctly,  
but data other than the presets will be lost.  
Before you replace the battery, store your data to an  
ATA-compliant PC flash storage card via the CS1D, or  
store the data to the personal computer by connecting  
the computer to the PC CONTROL “RS-232-C” con-  
nector on the DSP1D/DSP1D-EX.  
• Do not scratch, bend, twist, pull, or heat the power  
cord. A damaged power cord is a fire and electrical  
shock hazard.  
• Do not place heavy objects, including this unit, on top  
of the power cord. A damaged power cord is a fire and  
electrical shock hazard. In particular, be careful not to  
place heavy objects on a power cord covered by a car-  
pet.  
• The unit is equipped with the ground connector to  
avoid the risk of electrical shock.  
Be sure to ground the unit before you insert the power  
plug into an AC outlet.  
• Be sure to ground the unit to avoid the risk of electri-  
cal shock  
• If you notice any abnormality, such as smoke, odor, or  
noise, or if a foreign object or liquid gets inside the  
unit, turn it off immediately. Remove the power cord  
from the AC outlet. Consult your dealer for repair.  
Using the unit in this condition is a fire and electrical  
shock hazard.  
If the power cord has three pins and the ground con-  
nector on the AC outlet is grounded, the unit will be  
grounded effectively.  
• Should this unit/AC adapter/power supply be  
dropped or the cabinet be damaged, turn the power  
switch off, remove the power plug from the AC outlet,  
and contact your dealer. If you continue using the unit  
without heeding this instruction, fire or electrical  
shock may result.  
• If the power cord is damaged (i.e., cut or a bare wire is  
exposed), ask your dealer for a replacement. Using the  
unit with a damaged power cord is a fire and electrical  
shock hazard.  
• Do not remove the unit’s cover. You could receive an  
electrical shock. If you think internal inspection,  
maintenance, or repair is necessary, contact your  
dealer.  
• Do not modify the unit. Doing so is a fire and electri-  
cal shock hazard.  
• When rack-mounting the unit, allow enough free  
space around the unit for normal ventilation. This  
should be: 10 cm behind, and 20 cm above.  
• For normal ventilation during use, remove the rear of  
the rack or open a ventilation hole.  
• If the airflow is not adequate, the unit will heat up  
inside and may cause a fire.  
• This unit has ventilation holes at the rear and bottom  
to prevent the internal temperature rising too high.  
Do not block them. Blocked ventilation holes are a fire  
hazard.  
• Hold the power cord plug when disconnecting it from  
an AC outlet. Never pull the cord. A damaged power  
cord is a potential fire and electrical shock hazard.  
• Do not touch the power plug with wet hands. Doing  
so is a potential electrical shock hazard.  
3
 
Thank you for choosing the DSP unit “DSP1D/DSP1D-EX, specifically designed for the Yamaha PM1D  
digital audio mixing system. The DSP1D/DSP1D-EX is an engine controlled by the CS1D control surface.  
Be sure to ask an authorizedYamaha service engineer to install the boards and  
set up the unit. Never perform installation and setup by yourself.  
The following optional boards can be installed in the DSP1D.  
CIB1D : Console interface board  
EMB1D : Engine management board  
PDB1D : Patch DSP board  
GDB1D : Group DSP board  
EDB1D : Effect DSP board  
IDB1D : Input DSP board  
Front panel  
ENGINE ID  
1
A
B
CONTROL I/O  
2
3
ENGINE ID  
1
2
A
B
CONTROL I/O  
1
2
INPUT  
CONFIGURATION  
INPUT  
CONFIGURATION  
48CH  
96CH  
POWER  
ON/ OFF  
48CH  
96CH  
POWER  
ON/ OFF  
4
Rear panel  
MIDI  
CONTROL I/O  
CONSOLE  
L M N  
O
1
IN  
DIGITAL I/O  
IN  
OUT  
THRU  
CONSOLE  
I/O  
CASCADE  
OUTPUT  
INPUT  
OUT  
5
6
7
8
1
IN  
5
3
1
9
7
5
3
1
2
IN  
OUT  
MIDI  
CONTROL I/O  
CONSOLE  
DIGITAL I/O  
CONSOLE  
I/O  
CASCADE  
OUTPUT  
INPUT  
1
IN  
PC  
CONTROL  
1
IN  
5
3
1
9
7
3
1
IN  
OUT  
THRU  
OUT  
2
REMOTE  
RS-422  
IN  
OUT  
PC  
CONTROL  
REMOTE  
RS-422  
RS-232-C  
RS-232-C  
9
J
K
2
OUT  
6
4
2
10  
8
6
4
2
USB  
GPI  
WORD CLOCK  
IN  
OFF  
75Ω  
ON  
TIME CODE IN  
OUT  
USB  
GPI  
2
OUT  
6
4
2
10  
8
6
4
2
WORD CLOCK  
IN  
OFF  
75Ω  
ON  
TIME CODE IN  
OUT  
P
4
 
AENGINE ID A/B indicators  
DPOWER ON/OFF switch  
These indicators indicate whether the DSP1D/  
DSP1D-EX is connected to the engine A or engine B  
channel.  
Use this switch to turn the power to the DSP1D/  
DSP1D-EX on or off. When the power is turned on,  
the indicators 1- 3light up.  
Indicator A lights up if the DSP1D/DSP1D-EX is con-  
nected to the engine A channel jacks of the CS1D con-  
trol surface (DIGITAL I/O jack A and CONTROL I/O  
jack A). Indicator B lights up if the DSP1D/DSP1D-  
EX is connected to the engine B channel jacks of the  
CS1D control surface (DIGITAL I/O jack B and CON-  
TROL I/O jack B).  
EMIDI IN/OUT/THRU connectors  
These connectors are used to transmit and receive  
Program change messages, MMC, and other MIDI  
messages among external MIDI devices.  
FPC CONTROL RS-232-C/USB ports  
Connect these ports to a PC that runs Windows 95 or  
Windows 98 to control the PM1D system from the  
PC. Use a D-sub, 9-pin cross cable (female to female)  
to connect the RS-232-C port to the serial (COM)  
port on the PC. The USB port is provided for future  
system expansion, but it is not operative in the current  
software version.  
Error indication  
• If both ENGINE ID A and B indicators are flash-  
ing:  
There is a malfunction in the internal board  
(PDB, GDB, IDB1/2, EDB, EMB, or CIB). Or  
the necessary board does not exist.  
GWORD CLOCK IN jack, 75 ON/OFF  
switch, and WORD CLOCK OUT jack  
The WORD CLOCK IN jack is used to provide word  
clock to the PM1D system from the connected exter-  
nal device, such as a clock generator. Use the WORD  
CLOCK OUT jack to provide the word clock to the  
connected external device from the PM1D. Use a BNC  
cable with an impedance of 75 for the WORD  
CLOCK IN/OUT jacks.  
• If either ENGINE ID A or B indicator is flashing:  
During the Mirror mode operation, the  
ENGINE ID indicator for the unused DSP1D/  
DSP1D-EX flashes, indicating that the unit is in  
standby mode.  
If Indicator A is flashing, unit A is in standby  
mode. If Indicator B is flashing, unit B is in  
standby mode.  
The WORD CLOCK ON/OFF switch is used to termi-  
nate the word clock connection. Basically, if the  
DSP1D/DSP1D-EX is the last device of the word clock  
chain, or if nothing is connected to the WORD  
CLOCK IN/OUT jacks, set this switch to ON.  
BCONTROL I/O 1/2 indicators  
These indicators indicate which one of two CON-  
SOLE 1, 2 IN/OUT jacks (8) on the rear panel is cur-  
rently effective.  
Note:  
HCONSOLE 1, 2 IN/OUT jacks  
These jacks are connected to the CONTROL I/O  
CONSOLE jacks of the CS1D control surface to trans-  
mit or receive control signals. For connection, use a  
genuine Yamaha cable or a BNC cable with an imped-  
ance of 50 .  
When you turn on the power to the DSP1D/  
DSP1D-EX and the CS1D, and communication  
between the DSP1D/DSP1D-EX and the CS1D is  
established, one of these two indicators lights up. If  
neither one lights up, check the connection of the  
CONSOLE 1, 2 IN OUT jacks on the rear panel.  
IREMOTE RS-422 connector  
This D-sub 9-pin connector is used to control a con-  
nected tape recorder or a hard disk recorder. Serial  
commands can be transmitted through this connector  
to play or stop such a recorder.  
Error indication  
• If the CONTROL I/O 1 indicator is flashing:  
Communication between the CS1D control  
surface and the DSP1D is not established.The  
CONSOLE 1, 2 IN OUT jacks or the PC CON-  
TROL port is not connected correctly.  
This connector is provided for future system expan-  
sion, but it is not operative in the current software  
version.  
CINPUT CONFIGURATION 48CH/96CH  
indicators  
JGPI connector  
This connector is used to connect an external device  
that supports GPI (General Purpose Interface), such  
as a video editor to control the external device from  
the PM1D system or to perform certain functions of  
the PM1D system while controlling from the external  
device. You can connect a custom-made external  
switch here.  
This connector is provided for future system expan-  
sion, but it is not operative in the current software  
version.  
These indicators indicate how many input channels  
are currently available. On the DSP1D, the 48CH  
indicator lights up. On the DSP1D-EX, the 96CH  
indicator lights up.  
Error indication  
• If the INPUT CONFIGURATION 48CH is flashing:  
The signal is not locking to the word clock.  
5
 
KTIME CODE IN connector  
This balanced XLR3-31 connector receives SMPTE  
time code (LTC) for analog input from the external  
device. The rated input level is –10 dB, and the pin  
assignment is as follows.  
NOUTPUT 1–6 slot  
Use these slots to connect the INPUT connectors of an  
analog output unit AO8 series or DIO8 digital I/O  
unit to output multi-channel digital audio signals  
from the DSP1D/DSP1D-EX. Use a genuine Yamaha  
half-pitch 68-pin cable for connection.  
1=ground, 2=hot, 3=cold  
LCONSOLE I/O 1, 2 slots  
OINPUT 1–10 slot  
Connect these slots to the DIGITAL I/O CONSOLE  
jacks of the CS1D control surface to transmit multi-  
channel digital audio signals. Use a genuine Yamaha  
half-pitch 68-pin cable for connection.  
Use these slots to connect the OUTPUT connectors of  
an analog input unit AI8 series or DIO8 digital I/O  
unit series to input multi-channel digital audio signals  
to the DSP1D/DSP1D-EX. Use a genuine Yamaha  
half-pitch 68-pin cable for connection.  
MCASCADE IN, OUT slots  
PGround connector  
Use one of these connectors to cascade two DSP1D/  
DSP1D-EX units to transmit multi-channel digital  
audio signals. Use a genuine Yamaha half-pitch 68-pin  
cable to connect the CASCADE IN (or OUT) to the  
CASCADE OUT (or IN) of another DSP1D/DSP1D-  
EX.  
These connectors are provided for future system  
expansion, but they are not operative in the current  
software version.  
Be sure to ground the unit to avoid the risk of electrical  
shock before you insert the power plug into an AC outlet.  
This product comes with a 3-pin power cord. If the  
ground connector of the AC outlet has already been  
grounded, the unit will be grounded effectively by  
using the 3-pin power cord.  
Grounding the unit is also effective for preventing  
hum and other noise.  
Specifications  
<External sync> 39.69 kHz – 50.88 kHz  
<Internal sync> 44.1 kHz, 48 kHz  
Sampling frequency  
USA and Canada : 120 V, 60 Hz  
Others : 230 V, 50 Hz  
170 W  
Power supply  
Power consumption  
Dimensions (W × H × D)  
Weight  
480 mm × 408.7 mm × 460.8 mm  
33 kg  
Operating temperature  
Fan circuit  
10 – 35˚C  
always fixed  
Accessories  
power cable 2.5 m × 1  
Digital I/Os  
I/O connectors  
DIGITAL I/O INPUT 1 –10  
Level  
RS-422  
Type  
D-sub, half-pitch, 68-pin connector (female) × 10  
D-sub, half-pitch, 68-pin connector (female) × 6  
D-sub, half-pitch, 68-pin connector (female) × 2  
D-sub, half-pitch, 68-pin connector (female) × 2  
BNC connector × 2  
DIGITAL I/O OUTPUT 1 – 6  
DIGITAL I/O CASCADE IN, OUT  
DIGITAL I/O CONSOLE I/O 1, 2  
RS-422  
RS-422  
RS-422  
CONTROL I/O CONSOLE 1 IN, OUT –0.225V — –1.825V/50 Ω  
CONTROL I/O CONSOLE 2 IN, OUT –0.225V — –1.825V/50 Ω  
BNC connector × 2  
REMOTE RS-422  
RS-422  
D-sub, 9-pin connector (female)  
C-MOS IN, Open collector OUT  
1 pin: 150mA, 8pin total: 500mA  
GPI  
D-sub, 25-pin connector (female)  
TIME CODE IN  
SMPTE format, Nominal –10 dB/10 kXLR-3-31 type connector  
MIDI IN, OUT, THRU  
PC CONTROL RS-232-C  
PC CONTROL USB  
WORD CLOCK IN  
WORD CLOCK OUT  
MIDI format  
RS-232-C  
5-pin DIN connector × 3  
D-sub, 9-pin connector (male)  
B type USB connector  
BNC connector  
0V — 3.3V  
TTL/75 (ON/OFF)  
TTL/75 Ω  
BNC connector  
6
 
Slots (for IDB1D board)  
Unit  
DPS1D  
Input channel  
*
INPUT 1-48 & ST IN 1-4  
DPS1D-EX  
INPUT 1-96 & ST IN 1-8 (DSP1D + IDB1D for expansion)  
*The DSP1D has an empty slot available for the IDB1D board.  
Dimensions  
480  
ENGINE ID  
A
B
CONTROL I/O  
1
2
INPUT  
CONFIGURATION  
48CH  
96CH  
POWER  
ON/ OFF  
unit: mm  
• Specifications and appearance are subject to change without notice for improvement.  
• For European Model  
Purchaser/User information specified in EN55103-1 and EN55103-2.  
Inrush Current: 31A  
Conformed Environment: E1, E2, E3 and E4.  
7
 
YAMAHA CORPORATION  
Pro Audio Division, #18/3  
P.O. Box 3, Hamamatsu, 430-8651, Japan  
 

Weslo Home Gym QVRX10170 User Manual
West Marine Marine Radio 14078562 User Manual
Whirlpool Double Oven AKZM 656 User Manual
Whirlpool Water Dispenser WHELJ1 User Manual
Woodstock Personal Lift D4070 User Manual
Yamaha Home Theater Server MCX A300 User Manual
Yamaha Portable Generator EF3000iSE, EF3000iSEB User Manual
Zanussi Cooktop ZKT 652 DX User Manual
Zanussi Plumbing Product 132535 User Manual
Zanussi Refrigerator ZA 23 S User Manual